采用柠檬酸-硝酸盐自蔓延燃烧法分别合成了Pr_(0.6)Sr_(0.4)Co_(0.2)Fe_(0.8)O_(3-δ)(PSCF)和Gd_(0.2)Ce_(0.8)O_(2-δ)(GDC)粉体,高温固相法合成La_(0.9)Sr_(0.1)Ga_(0.8)Mg_(0.2)O_(3-δ)(LSGM)电解质粉体。以LSGM为电解质,PSCF同时...采用柠檬酸-硝酸盐自蔓延燃烧法分别合成了Pr_(0.6)Sr_(0.4)Co_(0.2)Fe_(0.8)O_(3-δ)(PSCF)和Gd_(0.2)Ce_(0.8)O_(2-δ)(GDC)粉体,高温固相法合成La_(0.9)Sr_(0.1)Ga_(0.8)Mg_(0.2)O_(3-δ)(LSGM)电解质粉体。以LSGM为电解质,PSCF同时作为阴极和阳极,GDC作为功能层材料,构建了对称固体氧化物燃料电池PSCF│GDC│LSGM│GDC│PSCF。利用X射线衍射法研究材料的成相以及相互间的化学稳定性,交流阻抗法记录界面极化行为,用扫描电子显微镜观察电池的断面微结构,用自组装的测试系统评价电池输出性能。结果表明,合成的PSCF粉体呈立方钙钛矿结构,具有良好的氧化–还原可逆性。使用GDC功能层明显改善了氢气环境下PSCF与LSGM材料间的化学相容性以及电池的输出性能,800℃时,电极│电解质界面极化电阻从6.892?·cm^2下降到0.314?·cm^2;以加湿H_2(含体积分数3%的水蒸气)为燃料气,空气为氧化气时,单电池输出功率密度由269 m W/cm2增大至463 m W/cm^2。研究结果显示,PSCF是对称固体氧化物燃料电池良好的候选电极材料,GDC功能层对改善电池长期稳定性能具有潜在的应用价值。展开更多
A series samples of La0.6M0.4FeO3-δ （M = Ca, Sr, process （GNP）. FTIR, TG-DSC, XRD and TEM techniques Ba） perovskite-type oxides were prepared by glycine nitrate were used to characterize the chemical constitution...A series samples of La0.6M0.4FeO3-δ （M = Ca, Sr, process （GNP）. FTIR, TG-DSC, XRD and TEM techniques Ba） perovskite-type oxides were prepared by glycine nitrate were used to characterize the chemical constitution, thermal stability and phase structure. The electrical conductivity of the samples was investigated by four-probe technique. With the increase of substituted-ionic radius, the temperature of phase formation increases, and the solid solubility decreases gradually, respectively. The La0.6Ca0.4FeO3-δ（LCF）powder is pure cubic perovskite-type crystalline after fired at 850℃ for 2 h. The XRD patterns of La0.6Sr0.4FeO3-δ（LSF） powder shows a small quantity of SrO peaks sintered at 1050℃ for 2 h. The electrical conductivity of LCF and LSF at 500 - 800℃ is over 100 S·cm^ - 1, and the value of LCF is 1170 S·cm^ - 1 at 800℃, which indicate that LCF and LSF may be used as a profitable cathode for IT-SOFCs. The characteristic of La0.6 Ba0.4FeO3-δ（LBF） is poor, and the electrical conductivity at intermediate temperatures is 1/20 less than that of LSF.展开更多
The conventional Ni cermet anode suffers from severe carbon deposition and sulfur poisoning when fossil fuels are used. Alternative anode materials are desired for high performance hydrocarbon fuel solid oxide fuel ce...The conventional Ni cermet anode suffers from severe carbon deposition and sulfur poisoning when fossil fuels are used. Alternative anode materials are desired for high performance hydrocarbon fuel solid oxide fuel cells （SOFCs）. We report the rational design of a very active Ni doped La0.6Sr0.4FeO3‐δ（LSFN） electrode for hydrocarbon fuel SOFCs. Homogeneously dispersed Ni‐Fe alloy nanoparticles were in situ extruded onto the surface of the LSFN particles during the operation of the cell. Sym‐metric SOFC single cells were prepared by impregnating a LSFN precursor solution onto a YSZ （yt‐tria stabilized zirconia） monolithic cell with a subsequent heat treatment. The open circuit voltage of the LSFN symmetric cell reached 1.18 and 1.0 V in humidified C3H8 and CH4 at 750？？, respective‐ly. The peak power densities of the cells were 400 and 230 mW/cm2 in humidified C3H8 and CH4, respectively. The electrode showed good stability in long term testing, which revealed LSFN has good catalytic activity for hydrocarbon fuel oxidation.展开更多
Single-phase perovskite La0.6Sr0.4Co0.8Fe0.2O3-δ has been successfully prepared by using citrate-EDTA complexation method at relatively low calcination temperature. The structure and thermal decomposition process of ...Single-phase perovskite La0.6Sr0.4Co0.8Fe0.2O3-δ has been successfully prepared by using citrate-EDTA complexation method at relatively low calcination temperature. The structure and thermal decomposition process of the complex precursor have been investigated by means of differential scanning calorimetry-thermal gravimetric analysis （DSC/TGA）, X-ray diffraction （XRD）, and Fourier transform infrared spectroscopic （FT-IR） measurements. The precursor decomposed completely and started to form perovskite-type oxide above 420 ℃ according to the differential scanning calorimetry （DSC） and thermal gravimetric analysis （TGA） results. Single-phase perovskite La0.6Sr0.4Co0.8Fe0.2O3-δ obtained has been confirmed from the XRD pattern, and no peak of SrCO3 was found by XRD of the oxides synthesized at a relatively low temperature of 800℃. The reducibility of La0.6Sr0.4Co0.8Fe0.2O3-δ was also characterized by the temperature programmed reduction （TPR） technique. Disk shaped dense La0.6Sr0.4Co0.8Fe0.2O3-δ membrane was prepared by the isostatical pressing method. The oxygen flux rate of dense La0.6Sr0.4Co0.8Fe0.2O3-δ membrane was （2.8-18）× 10^-8 mol/（cm^2.s） in the temperature range of 800-1000 ℃.展开更多
Ba0.6Sr0.4TiO3 (BST) thin films were fabricated on Pt coated Si (100) substrates by sol-gel techniques with molar ratio of (Ba+Sr) to Ti changing from 0.76 to 1.33. The effect of (Ba+Sr)/Ti ratio deviating from the st...Ba0.6Sr0.4TiO3 (BST) thin films were fabricated on Pt coated Si (100) substrates by sol-gel techniques with molar ratio of (Ba+Sr) to Ti changing from 0.76 to 1.33. The effect of (Ba+Sr)/Ti ratio deviating from the stoichiometry on microstructure, grain growth, dielectric and tunable properties of BST thin films were investigated. TiO2 and (Ba,Sr)2TiO4 were found as a second phase at the ratios of 0.76 and 1.33, respectively. The variation of the ratio reveals more significant effect on the grain size in B-site rich samples than that in A-site rich samples. The dissipation factor decreases rapidly from 0.1 to 0.01 at 1 MHz with decreasing (Ba+Sr)/Ti ratio. The tunability increases with decreasing ratio from 1.33 to 1.05, and then decreases with decreasing ratio from 1.05 to 0.76. The film with (Ba+Sr)/Ti ratio of 1.05 has a maximum tunability of 32% and a dissipation factor of 0.03 at 1 MHz.展开更多
以丙烯酰胺辅助柠檬酸为络合试剂,采用溶胶-凝胶燃烧法制备La0.6Sr0.4Co1-xMnxO3催化剂(x=0.3、0.5、0.7)并与La Co O3进行比较,进行XRD、BET、SEM、XPS和苯的催化氧化性能和稳定性表征。结果表明,催化活性顺序为:La0.6Sr0.4Co0.7Mn0.3O...以丙烯酰胺辅助柠檬酸为络合试剂,采用溶胶-凝胶燃烧法制备La0.6Sr0.4Co1-xMnxO3催化剂(x=0.3、0.5、0.7)并与La Co O3进行比较,进行XRD、BET、SEM、XPS和苯的催化氧化性能和稳定性表征。结果表明,催化活性顺序为:La0.6Sr0.4Co0.7Mn0.3O3>La0.6Sr0.4Co0.5Mn0.5O3>La0.6Sr0.4Co0.3Mn0.7O3>La Co O3。La0.6Sr0.4Co1-xMnxO3催化剂生成钙钛矿相的同时还伴生少量Sr CO3杂相。与La Co O3对比,La0.6Sr0.4Co1-xMnxO3催化剂拥有更大的比表面积、孔容和抗团聚性,具有更好的催化氧化活性。在La0.6Sr0.4Co1-xMnxO3(x=0.3、0.5、0.7)催化剂中,La0.6Sr0.4Co0.7Mn0.3O3催化剂比其他两种催化剂具有更高的钙钛矿相结晶度和更多的表面吸附氧与晶格氧,活性最高。78 h稳定性测试结果表明,La0.6Sr0.4Co0.7Mn0.3O3催化剂表现出良好的稳定性。展开更多
文摘采用柠檬酸-硝酸盐自蔓延燃烧法分别合成了Pr_(0.6)Sr_(0.4)Co_(0.2)Fe_(0.8)O_(3-δ)(PSCF)和Gd_(0.2)Ce_(0.8)O_(2-δ)(GDC)粉体,高温固相法合成La_(0.9)Sr_(0.1)Ga_(0.8)Mg_(0.2)O_(3-δ)(LSGM)电解质粉体。以LSGM为电解质,PSCF同时作为阴极和阳极,GDC作为功能层材料,构建了对称固体氧化物燃料电池PSCF│GDC│LSGM│GDC│PSCF。利用X射线衍射法研究材料的成相以及相互间的化学稳定性,交流阻抗法记录界面极化行为,用扫描电子显微镜观察电池的断面微结构,用自组装的测试系统评价电池输出性能。结果表明,合成的PSCF粉体呈立方钙钛矿结构,具有良好的氧化–还原可逆性。使用GDC功能层明显改善了氢气环境下PSCF与LSGM材料间的化学相容性以及电池的输出性能,800℃时,电极│电解质界面极化电阻从6.892?·cm^2下降到0.314?·cm^2;以加湿H_2(含体积分数3%的水蒸气)为燃料气,空气为氧化气时,单电池输出功率密度由269 m W/cm2增大至463 m W/cm^2。研究结果显示,PSCF是对称固体氧化物燃料电池良好的候选电极材料,GDC功能层对改善电池长期稳定性能具有潜在的应用价值。
基金Project Supported bythe Natural Science Foundation of Bureau Education Anhui Province (N2004kj326)
文摘A series samples of La0.6M0.4FeO3-δ （M = Ca, Sr, process （GNP）. FTIR, TG-DSC, XRD and TEM techniques Ba） perovskite-type oxides were prepared by glycine nitrate were used to characterize the chemical constitution, thermal stability and phase structure. The electrical conductivity of the samples was investigated by four-probe technique. With the increase of substituted-ionic radius, the temperature of phase formation increases, and the solid solubility decreases gradually, respectively. The La0.6Ca0.4FeO3-δ（LCF）powder is pure cubic perovskite-type crystalline after fired at 850℃ for 2 h. The XRD patterns of La0.6Sr0.4FeO3-δ（LSF） powder shows a small quantity of SrO peaks sintered at 1050℃ for 2 h. The electrical conductivity of LCF and LSF at 500 - 800℃ is over 100 S·cm^ - 1, and the value of LCF is 1170 S·cm^ - 1 at 800℃, which indicate that LCF and LSF may be used as a profitable cathode for IT-SOFCs. The characteristic of La0.6 Ba0.4FeO3-δ（LBF） is poor, and the electrical conductivity at intermediate temperatures is 1/20 less than that of LSF.
基金supported by the National Natural Science Foundation of China (51372271,51172275)the National Basic Research Program of China (973 Program,2012CB215402)~~
文摘The conventional Ni cermet anode suffers from severe carbon deposition and sulfur poisoning when fossil fuels are used. Alternative anode materials are desired for high performance hydrocarbon fuel solid oxide fuel cells （SOFCs）. We report the rational design of a very active Ni doped La0.6Sr0.4FeO3‐δ（LSFN） electrode for hydrocarbon fuel SOFCs. Homogeneously dispersed Ni‐Fe alloy nanoparticles were in situ extruded onto the surface of the LSFN particles during the operation of the cell. Sym‐metric SOFC single cells were prepared by impregnating a LSFN precursor solution onto a YSZ （yt‐tria stabilized zirconia） monolithic cell with a subsequent heat treatment. The open circuit voltage of the LSFN symmetric cell reached 1.18 and 1.0 V in humidified C3H8 and CH4 at 750？？, respective‐ly. The peak power densities of the cells were 400 and 230 mW/cm2 in humidified C3H8 and CH4, respectively. The electrode showed good stability in long term testing, which revealed LSFN has good catalytic activity for hydrocarbon fuel oxidation.
基金Sponsored by SRF for ROCS, key lab of enhanced heat transfer and energy conservation (MOE)Guangdong provincial natural science foundation (04020126).
文摘Single-phase perovskite La0.6Sr0.4Co0.8Fe0.2O3-δ has been successfully prepared by using citrate-EDTA complexation method at relatively low calcination temperature. The structure and thermal decomposition process of the complex precursor have been investigated by means of differential scanning calorimetry-thermal gravimetric analysis （DSC/TGA）, X-ray diffraction （XRD）, and Fourier transform infrared spectroscopic （FT-IR） measurements. The precursor decomposed completely and started to form perovskite-type oxide above 420 ℃ according to the differential scanning calorimetry （DSC） and thermal gravimetric analysis （TGA） results. Single-phase perovskite La0.6Sr0.4Co0.8Fe0.2O3-δ obtained has been confirmed from the XRD pattern, and no peak of SrCO3 was found by XRD of the oxides synthesized at a relatively low temperature of 800℃. The reducibility of La0.6Sr0.4Co0.8Fe0.2O3-δ was also characterized by the temperature programmed reduction （TPR） technique. Disk shaped dense La0.6Sr0.4Co0.8Fe0.2O3-δ membrane was prepared by the isostatical pressing method. The oxygen flux rate of dense La0.6Sr0.4Co0.8Fe0.2O3-δ membrane was （2.8-18）× 10^-8 mol/（cm^2.s） in the temperature range of 800-1000 ℃.
基金Project (50332030) supported by the National Natural Science Foundation of China
文摘Ba0.6Sr0.4TiO3 (BST) thin films were fabricated on Pt coated Si (100) substrates by sol-gel techniques with molar ratio of (Ba+Sr) to Ti changing from 0.76 to 1.33. The effect of (Ba+Sr)/Ti ratio deviating from the stoichiometry on microstructure, grain growth, dielectric and tunable properties of BST thin films were investigated. TiO2 and (Ba,Sr)2TiO4 were found as a second phase at the ratios of 0.76 and 1.33, respectively. The variation of the ratio reveals more significant effect on the grain size in B-site rich samples than that in A-site rich samples. The dissipation factor decreases rapidly from 0.1 to 0.01 at 1 MHz with decreasing (Ba+Sr)/Ti ratio. The tunability increases with decreasing ratio from 1.33 to 1.05, and then decreases with decreasing ratio from 1.05 to 0.76. The film with (Ba+Sr)/Ti ratio of 1.05 has a maximum tunability of 32% and a dissipation factor of 0.03 at 1 MHz.
文摘以丙烯酰胺辅助柠檬酸为络合试剂,采用溶胶-凝胶燃烧法制备La0.6Sr0.4Co1-xMnxO3催化剂(x=0.3、0.5、0.7)并与La Co O3进行比较,进行XRD、BET、SEM、XPS和苯的催化氧化性能和稳定性表征。结果表明,催化活性顺序为:La0.6Sr0.4Co0.7Mn0.3O3>La0.6Sr0.4Co0.5Mn0.5O3>La0.6Sr0.4Co0.3Mn0.7O3>La Co O3。La0.6Sr0.4Co1-xMnxO3催化剂生成钙钛矿相的同时还伴生少量Sr CO3杂相。与La Co O3对比,La0.6Sr0.4Co1-xMnxO3催化剂拥有更大的比表面积、孔容和抗团聚性,具有更好的催化氧化活性。在La0.6Sr0.4Co1-xMnxO3(x=0.3、0.5、0.7)催化剂中,La0.6Sr0.4Co0.7Mn0.3O3催化剂比其他两种催化剂具有更高的钙钛矿相结晶度和更多的表面吸附氧与晶格氧,活性最高。78 h稳定性测试结果表明,La0.6Sr0.4Co0.7Mn0.3O3催化剂表现出良好的稳定性。
