Heat Treatment Effect on Microstructure, Hardness and Wear Resistance of Cr26 White Cast Iron

High chromium cast iron（HCCI） is taken as material of coal water slurry pump impeller, but it is susceptible to produce serious abrasive wear and erosion wear because of souring of hard coal particles. The research on optimization of heat treatments to improve abrasive wear properties of HCCI is insufficient, so effect of heat treatments on the microstructure, hardness, toughness, and wear resistance of Cr26 HCCI is investigated to determine the optimal heat treatment process for HCCI. A series of heat treatments are employed. The microstructures of HCCI specimens are examined by using optical microscopy and scanning electron microscopy. The hardness and impact fracture toughness of as-cast and heat treated specimens are measured. The wear tests are assessed by a Type M200 ring-on block wear tester. The results show the following： With increase of the quenching temperature from 950 ℃ to 1050 ℃, the hardness of Cr26 HCCI increased to a certain value, kept for a time and then decreased. The optimal heat treatment process is 2 h quenching treatment at 1000 ℃, followed by a subsequent 2 h tempering at 400 ℃. The hardness of HCCI is related to the precipitation and redissolution of secondary carbides in the process of heat treatment. The subsequent tempering treatment would result in a slight decrease of hardness but increase of toughness. The wear resistance is much related to the ＂supporting＂ effect of the matrix and the ＂protective＂ effect of the hard carbide embedded in the matrix, and the wear resistance is further dependent on the hardness and the toughness of the matrix. This research can provide an important insight on developing an optimized heat treatment method to improve the wear resistance of HCCI.

Effect of heat treatment on the microstructure and hardness of C-Cr-W-Mo-V-RE Fe-based hardfacing layer

After different heat treatment processes, the metal compound, the microstructure and the hardness of the C-Cr-W- Mo-V-RE Fe-based hardfacing layers are investigated by means of metallographic microscope, X-ray diffraction （ XRD ）, energy dispersive spectrum（ EDS ）, transmission electron microscope（TEM） and hardness tester. The results show that the hardfacing layers have higher tempering stability and secondary hardening property. After quenching at 820 ℃ ,the hardness value（ HRC37 ） and the microstructure of the layers are similar to that normalized at 820 - 1 000 ℃. The tempering stability and the hardness increases with increasing quench temperature, which is attributed to the amount of the alloy element in the matrix. These results are very helpful for improving the mechanical properties of the hardfacing layers.

Influence of post-weld heat treatment on the microstructure and hardness of laser weld seams on hot-rolled TRIP 800 steel

The transformation induced plasticity (TRIP) steels effect occurs because of the martensitic transformation of retained austenite during plastic deformation,and it provides the steel with excellent strength and ductility.While welding remains a vital part of auto body manufacturing,the weldability of TRIP steels is problematic,and this prevents its adoption for many applications in the automotive industry.This present work studies the effects of welding and post-weld heat treatment on the microstructure of TRIP steels.It is found that the microstructures of the fusion zone and the heat affected zone (HAZ) are changed after high-temperature heat treatment.Hardness tests revealed that fusion zone hardness decreased with increasing of temperatures in the post-weld heat treatment on the laser weld seam.The rolling performance of the welding seam and the seam of post-weld heat treatment were also studied.

Effects of Heat Treatment on Hardness and Dry Wear Properties of a Semi-Solid Processed Fe-27 wt pct Cr-2.9 wt pct C Cast Iron

EfFects of heat treatments on hardness and dry wear properties of a semi-solid processed Fe-26.96 wt pct Cr- 2.91 wt pct C cast iron were studied. Heat treatments included tempering at 500℃, destabilisation at 1075℃ and destabilisation at 1075℃ plus tempering at 500℃, all followed by air cooling. Electron microscopy revealed that, in the as-cast condition, the primary proeutectic austenite was round in shape while the eutectic M7C3 carbide was found as radiating clusters mixed with directional clusters. Tempering did not change the microstructure significantly when observed by scanning or transmission electron microscopy. Destabilisation followed by air cooling led to a precipitation of secondary M23C6 carbide and a transformation of the primary austenite to martensite. Precipitation behaviour is comparable to that observed in the conventionally cast iron. Tempering after destabilisation resulted in a higher amount of secondary carbide precipitation within the tempered martensite in the eutectic structure. Vickers macrohardness and microhardness in the proeutectic zones were measured. Dry wear properties were tested by using a pin-on-disc method. The maximum hardness and the lowest dry wear rate were obtained from the destabilisation-plus-tempering heat treatment due to the precipitation of secondary carbides within the martensite matrix and a possible reduction in the retained austenite.

Effect of solution treatment on microstructure and hardness of rheo-forming AZ91-Y alloy

The microstructure and hardness of rheo-forming AZ91-Y alloy before and after solution treatment(ST) have been investigated by means of optical microscope(OM), scanning electron microscope(SEM) equipped with energy dispersive spectroscopy(EDS), X-ray diffraction(XRD) and Vickers. The experimental results showed that the β-Mg17Al12 phase of alloy was nearly dissolved after ST for 5 min. With the increasing of ST duration to 28 h, both the primary and secondarily solidified α-Mg grains faded away. At the same time, the alloy exhibited a much smoother surface due to the diffusion of solute atoms(Al). During ST, the thermal stable phase of Al2 Y produced by ultrasonic vibration retained its size and morphology. As the ST duration was increased, the alloy hardness decreased sharply at first, and then gradually reached a minimum level. The alloy's appropriate ST duration at 410 °C was approximately 28 h.

Effect of Heat Treatment on Hardness and Impact Toughness of CuCr Containing RE Alloy

The effect of heat treatment on hardness and impact toughness of CuCr containing rare earth alloy was studied by means of metallographic, XRD, SEM/EDX, TEM and mechanical property test. The results show that the heat treatment can change the hardness of CuCr alloy, and has smaller influence to its impact toughness. The optimum properties of CuCr containing RE alloy could be obtained by aging treatment at 500 ℃ for 2 h. And the causes of the above changes and the function of RE were analyzed.

Effect of Austenitizing Treatment on Structure and Hardness of Bainite DuctileCast Iron

By continuous quenching process, the effect of austenitizing temperature and time on the structure and hardness of bainiteductile cast iron was studied. It was found that (l) low austenitizing temperature would result in scrap ferrite existing in matrix, whichreduces the macro-hardness of bainite ductile cast iron; (2) high austenitizing temperature would make carbide decomposed, which alsoinduces the macro-hardness of bainite cast iron, and (3) austenitizing time has little effect on the structure of bainite ductile cast iron, butas it increases, the macro-hardness ofbainite ductile cast iron and micro-hardness of bainite increases. To the ductile cast iron, as a result,the suitable austenitizing temperature and time are recommended as 880 and 120 min respectively.

Measurement and Analysis on Hardness and Residual Stress of Heavy Forging after Heat Treatment

The hardness and residual stress in the forging for cold roller during low temperature tempering,and the relationship of residual stress and cooling temperature of high temperature tempering for heavy forgings were studied.The stress relaxation constant at low temperature tempering and the elasto-plastisity inversion temperature at high temperature tempering were found.The results are of great importance to determine rational tempering cooling process of heavy forgings.

Influence of vacuum heat treatment on structure and micro-hardness of electroless Ni-P-SiC composite coating

The electroless Ni-P-SiC composite coatings were prepared and the influence of vacuum heat treatment on its structure and properties was analyzed. The Ni-P-SiC composite coatings were characterized by morphology,structure and micro-hardness. The morphology and structure of the Ni-P-SiC composite coatings were studied by scanning electron microscopy(SEM) and X-ray diffractometry(XRD),respectively. A great deal of particles incorporation and uniform distribution were found in Ni-P-SiC composite coatings. XRD results show a broad peak of nickel and low intensity SiC peaks present on as-deposited condition. Micro-hardness of as-deposited Ni-P-SiC composite coatings is improved greatly,and the best micro-hardness is obtained after heat treatment in a high vacuum at 400 ℃ .

Effects of Heat Treatment on Microstructure and Hardness of Laser Clad NiWCRE Alloy Layer

The effects of heat treatment on tnicrostructure and hardness of laser surface-clad Ni2 !+20%WC+0.5%CeO2 on the heat-resistant cast iron were investigated by means of X-ray diffraction(XRD), transmission electron microscope(TEM) and microhardness test. The experimental results showed that heat-treating at 500’C has no effect on microstructure and hardness of the layers. Although the phase composition of the layers heat-treated at 700°C and 800°C remain unchanged, more Ni3B and N14B3 phases are precipitated on the matrix of the cladding layer, the metastable phase—M7C3 is transformed into steady phase—M23C6, and the precipitated phases coarsened.

Hardness Profile Prediction for a 4340 Steel Spline Shaft Heat Treated by Laser Using a 3D Modeling and Experimental Validation

Laser surface transformation hardening becomes one of the most effective processes used to improve wear and fatigue resistance of mechanical parts. In this process, the material physicochemical properties and the heating system parameters have significant effects on the characteristics of the hardened surface. To appropriately exploit the benefits presented by the laser surface hardening, it is necessary to develop a comprehensive strategy to control the process variables in order to produce desired hardened surface attributes without being forced to use the traditional and fastidious trial and error procedures. The paper presents a study of hardness profile predictive modeling and experimental validation for spline shafts using a 3D model. The proposed approach is based on thermal and metallurgical simulations, experimental investigations and statistical analysis to build the prediction model. The simulation of the hardening process is carried out using 3D finite element model on commercial software. The model is used to estimate the temperature distribution and the hardness profile attributes for various hardening parameters, such as laser power, shaft rotation speed and scanning speed. The experimental calibration and validation of the model are performed on a 3 kW Nd:Yag laser system using a structured experimental design and confirmed statistical analysis tools. The results reveal that the model can provide not only a consistent and accurate prediction of temperature distribution and hardness profile characteristics under variable hardening parameters and conditions but also a comprehensive and quantitative analysis of process parameters effects. The modelling results show a great concordance between predicted and measured values for the dimensions of hardened zones.

Effect of Precipitation on the Hardness of Ternary Metallic Glass

The present study reports effects of annealing treatment on the hardness of Ce75Al23Si2 rare earth-based metallic glasses (REMG). Then specimens were annealed at 100°C, 200°C, 250°C, 270°C, and 290°C five different temperatures for 30 minutes. After that, three different characteristic methods, including microindentation, X-ray Diffraction (XRD), and scanning electrical microscope (SEM) were conducted on the as received REMG sample and five annealed samples. XRD data demonstrate that the crystallization occurs in the sample at the annealing temperature as low as 200°C. The microindentation measurement shows that hardness of the REMG sample does not change at all before crystallization occurs in the sample and increases with the annealing temperature in the range of 200°C to 290°C. The average crystal size in the annealed samples was estimated using Debye-Scherrer equation to be 28-42 nm, in consistent with the SEM observation, indicating that nano-crystalline domains may give rise to the enhancement of hardness.

Microstructures and Hardness of 8CrWMoV Steel with Multiple Types of Ultra Fine Carbides

The structure and hardness of 8CrWMoV steel with multiple types of ultra fine carbides are studied after annealing, quenching and tempering in this paper. The results show that multiple types of carbides M3C, M7C3, M23C6, M6C and MC were observed in the annealed steel. Nucleation and coalescence of new carbides, partial dissolution of original carbides in γ phase region during annealing at 800～840℃, result in ultra-fine carbides. Average size of the carbides is0.33～0.34μm in the steel annealed at 800～840℃. Because M3C and M23C6 dissolve easily in austenite, the high hardness HRC63～65 can be obtained by quenching at 840～860℃. Un-dissolved carbides M6C and MC (VC) can effectively prevent the coarsening of austenitic grain, and conduce to obtain very fine martensite. The retained austenite can be easy to decompose during tempering at low and middle temperature due to the precipitation of multiple types of carbides and the good tempering-resistance of the steel is obtained. The microstructure and property of the steel after heat treatment can be accurately explained by calculating based on phase equilibrium thermodynamic.Key Words: 8CrWMoV steel, ultra-fine carbide, heat treatment, microstructure,

Effect of Cryogenic Treatment on Microstructure and Tribological Property Evolution of Electron Beam Melted Ti6Al4V

Cryogenic treatment was used to improve the tribological properties of Ti6Al4V artificial hip joint implants.Cryogenic treatment at-196℃with different holding time were carried out on Ti6Al4V specimens fabricated using electron beam melting(EBM),and their microstructure and tribological properties evolution were systematically analyzed by scanning electron microscopy(SEM),vickers hardness,and wear tests.The experimental results show that the as-fabricated specimen consists of lamellarαphase andβcolumnar crystal.While,the thickness of lamellarαphase decreased after cryogenic treatment.In addition,it can be found that the fineαphase was precipitated and dispersed between the lamellarαphase with the holding time increase.Vickers hardness shows a trend of first increasing and then decreasing.The wear rate of the specimen cryogenic treated for 24 h is the minimum and the average friction coefficient is 0.50,which is reduced by 14.61%compared with the as-fabricated.The wear mechanism of the as-fabricated specimen is severe exfoliation,adhesive,abrasive,and slight fatigue wear.However,the specimen cryogenic treated for 24 h shows slight adhesive and abrasive wear.It can be concluded that it is feasibility of utilizing cryogenic treatment to reduce the wear of EBMed Ti6Al4V.

Surgical treatment of severe anterior capsular organized hard core cataract: A case report

BACKGROUND Complicated cataract surgery is challenging,especially in cases of hard nuclear cataract with severe anterior capsule organization.It is important to avoid the risk of surgery and improve the surgical skills of surgeons.CASE SUMMARY A 60-year-old man presented with severe cataract and visual impairment.The anterior capsule of the lens was irregularly organized and pulled to the surrounding capsule,and white porcelain organized cord and brown-black lens nucleus were clearly visible.In phacoemulsification,maintaining the anterior capsule round and intact plays a key role in a successful surgery.In this case,if the conventional capsule treatment method was used,the anterior capsule would be torn.Therefore,we adopted a segmented anterior capsule treatment method,and a blasting method to release energy when dealing with the lens nucleus,and achieved good surgical results.CONCLUSION Complicated cataract surgery is challenging and requires precise skills.Operation plans should be made reasonably to predict the risk of surgery,and improve the visual quality of the patients.

Experimental Study of Effluent Salty Wastewater Treatment from a Solar Desalination Pond

In this research, the quality of the wastewater discharged into the environment has been investigated. The effluent from solar desalination pond contains large amounts of TDS (3.68 grams per liter) and TH (6.50 grams per liter). Since the use of filter is not economical in this case, three types of commercial coagulants such as aluminum sulfate, ferric chloride and ferric sulfide have been used in this study. The main parameters such as effectiveness of three inorganic coagulants, ammonium sulfate, ferric sulfate, and ferric chloride, which separately help to remove hardness, have been studied. According to the results, using laboratory test, 25/g of ferric sulfate as coagulant is best coagulant mass and the ratio of 4 to 3 for auxiliary coagulant (sodium carbonate and sodium hydroxide) to coagulant will be best ratio. Also, the mixing rate of 120 rpm in the first reactor will give the best mixing speed. These conditions will lead to 0.348 grams per liter of TDS, 0.345 grams per liter of TH and 0.195 grams per liter of calcium hardness and 300 micro Siemens electrical conductivity of the purified sample.

Effects of annealing temperature on the microstructure and hardness of TiAlSiN hard coatings

TiAlSiN hard coatings were synthesized on high-speed steel using an arc ion enhanced magnetic sputtering hybrid system.The microstructure and hardness of the coatings at different annealing temperatures were explored by means of XRD,TEM,EDAX and Vickers indentation.The as-deposited TiAlSiN coatings were confirmed to be amorphous due to high depositing rate and low deposition temperature during the film growth.The transformation from amorphous to nanocomposites of nano-crystallites and amorphousness were observed after the annealing treatment,the microstructure of TiAlSiN coatings annealed at 800°C and 1000°C were consisted of crystalline hcp-AlN,fcc-TiN and amorphous phase,however,the coatings were only consisted of fcc-TiN and amorphous phase when annealing at 1100°C and 1200°C.Meanwhile,the formation of Al2O3 was detected on the coating surface after annealing at 1200°C and it indicated the excellent oxidation resistance of the TiAlSiN coatings under the present experimental conditions.Furthermore,the average grain size of the TiAlSiN coatings after high temperature annealing even at 1200°C was less than 30 nm and the size increased with the increasing temperature.However,the hardness of the so-deposited coatings with HV0.2N=3300 dramatically decreased with the increase of temperature and reached nearly to the hardness of TiN coatings with HV0.2N=2300.