Microstructure and mechanical properties of hot isostatically pressed cermets with TiN coatings

To increase the adhesion strength between the coating and the substrate, sintered Ti（C,N）-based cermets were selected and deposited with monolayer TiN using a multiarc ion-plating technique; subsequently, hot isostatic pressing （HIPhag） treatment was performed at 1000℃ using nitrogen pressure up to 110 MPa. The mechanical properties of cermets after a coating process and subsequent HIPing treatment have been evaluated with respect to the hardness, the residual stress, and the coating adhesion. The results show that atter the HIPing process, there was a higher increase ha critical load ha the TiN-coated cermets with lower surface roughness compared with those with higher surface roughness. In all cases, the residual stress was found to be compressive. The effects of substrate surface roughness and posttreatment on the adhesion strength of the coatings were thus investigated. It was also fotmd that the HIPing posttreatment process is well suited for hacreasing the adhesion strength between the coating and the substrate.

COERCIVITY AND ITS GRAIN SIZE DEPENDENCE IN CAST-HOT PRESSED Pr-Fe-B MAGNETS

Characteristics of magnetic hardening in cast-hot pressed magnet Pr_(19)Fe_(74.5)B_5Cu_(1.5)were stu- died.The microstructure features and virgin magnetization curve reveal a nucleation control- led coercivity mechanism.Regression analysis shows that the intrinsic coercivity varies inversely as the logarithm of the average grain size: _iH_c(MA/m)=1.7312-0.48161nd(μm) which confirms the randomness of nucleation of reversed domains and the statistical nature of coercivity,indicating that the decrease of grain size would reduce the average number of de- fects on its surface and lower the probability of magnetization reversal of a grain and the cu- mulative fraction of the grains that have reversed their magnetization.Coercivity is thus en- hanced.

Preparation and Characterization of Hot-Pressed and Sintered BiPbSrCaCuO Superconductor

Powder compacts of the system Bi2–xPbxSr2Ca2Cu3Oy with 0 ≤ x ≤ 0.5 molar ratio using both techniques;isothermal hot pressing and the solid state reaction (sintering). The XRD of the hot pressed powder compacts of the nominal compositions Bi2–xPbxSr2Ca2Cu3Oy showed 2212 and 2223 phases. The resistivity temperature variations belonging to the composition Bi1.8Pb0.2Sr2Ca2Cu3Oy showed metal-superconducting transition at Tons = 143 K for the annealed sample for 24 h. The annealed nominal composition Bi1.5Pb0.5Sr2Ca2Cu3Oy for 18 h showed metal to superconducting transition at 80 K.

Modulating Myofibroblastic Differentiation of Fibroblasts through Actin-MRTF Signaling Axis by Micropatterned Surfaces for Suppressed Implant-Induced Fibrosis

Myofibroblasts,the primary effector cells for implant-induced fibrosis,contribute to this process by secreting excessive collagen-rich matrix and contracting.Thus,approaches that suppress myofibroblasts may achieve desirable suppression effects in the fibrotic process.As one of the important physical properties of materials,material topographical structures have been proven to affect various aspects of cell behaviors,so is it possible to manipulate the formation of myofibroblasts by tailoring the topographical properties of medical devices?In this study,polycaprolactone(PCL)surfaces with typical micropatterns(micro column and micro pit)were fabricated.The regulatory effects of surface micropatterns on the myofibroblastic differentiation of fibroblasts were investigated.Compared to the flat surfaces and surfaces with micro pit,surfaces with micro columns triggered the F-to G-actin transition,inhibiting the nuclear transfer of myocardin-related transcription factor-A.Subsequently,the downstream geneα-smooth muscle actin,which is a marker of myofibroblasts,was suppressed.Further in vivo investigation showed that PCL implants with micro-column-patterned surfaces inhibited the formation of peri-implant fibrotic capsules.Our results demonstrate that surface topographical properties are a potent regulator of fibroblast differentiation into myofibroblasts and highlight the antifibrotic potential of modifying surfaces with micro-column patterns.

IPS e.max Press铸瓷与合金嵌体治疗后牙牙体缺损效果对比研究

目的探讨IPS e.max Press铸瓷与合金嵌体治疗后牙牙体缺损的效果。方法前瞻性纳入2020-05—2022-05三门峡市中心医院口腔科收治的后牙牙体缺损患者,根据修复材料分为IPS e.max Press铸瓷嵌体组(铸瓷组)和合金嵌体组(合金组)。比较2组患者的基线资料。治疗前后检测患者的龈沟液中炎性因子、评价牙周健康情况。治疗3个月后评价牙体缺损边缘密合度和美牙效果。结果共纳入86例(132颗牙)患者,每组43例(66颗牙)。2组患者的基线资料差异无统计学意义(P>0.05)。治疗后铸瓷组患者的IL-6、IL-8、CXCL16水平和GI、SBI及PLI评分均低于合金组;牙体缺损边缘密合度优于合金组,美牙效果满意率高于合金组。差异均有统计学意义(P<0.05)。结论与合金嵌体比较,采用IPS e.max Press铸瓷嵌体治疗后牙牙体缺损有利于降低龈沟液中炎性因子水平,改善牙周健康状况和牙体缺损边缘密合度,并可提高患者对美牙效果的满意度。但仍需进行更大样本量的前瞻性随机对照研究予以证实。

Effect of hot isostatic pressure on the microstructure and tensile properties of γ'-strengthened superalloy fabricated through induction-assisted directed energy deposition

The microstructure characteristics and strengthening mechanism of Inconel738LC(IN-738LC) alloy prepared by using induction-assisted directed energy deposition(IDED) were elucidated through the investigation of samples subjected to IDED under 1050℃ preheating with and without hot isostatic pressing(HIP,1190℃,105 MPa,and 3 h).Results show that the as-deposited sample mainly consisted of epitaxial columnar crystals and inhomogeneously distributed γ’ phases in interdendritic and dendritic core regions.After HIP,grain morphology changed negligibly,whereas the size of the γ’ phase became increasingly even.After further heat treatment(HT,1070℃,2 h + 845℃,24 h),the γ’ phase in the as-deposited and HIPed samples presented a bimodal size distribution,whereas that in the as-deposited sample showed a size that remained uneven.The comparison of tensile properties revealed that the tensile strength and uniform elongation of the HIP + HTed sample increased by 5% and 46%,respectively,due to the synergistic deformation of bimodal γ’phases,especially large cubic γ’ phases.Finally,the relationship between phase transformations and plastic deformations in the IDEDed sample was discussed on the basis of generalized stability theory in terms of the trade-off between thermodynamics and kinetics.

Effect of Adhesive Type on the Quality of Coconut Shell Charcoal Briquettes Prepared by the Screw Extruder Machine

Indonesia is one of the largest coconut-producing countries in the world.The utilization of coconut shell waste into briquettes will increase the selling value and become a great export opportunity.However,the effect of adhesives on the quality of coconut shell charcoal briquettes made using screw extruder machine has not been widely studied.This study aims to determine the effect of adhesive type on the quality of coconut shell charcoal briquettes.The process of fabricating briquettes in this study included crushing,mixing,blending,pressing,and drying.In the mixing process,3 types of adhesives were used,namely tapioca flour(Briquette_1),cassava flour(Briquette_2),and modified cassava flour(Briquette_3)with a concentration of 5%of the weight of coconut shell charcoal powders.The quality of the resulting briquettes and commercial briquettes will be evaluated by moisture content,ash content,volatile matter,fixed carbon,calorific value,density,compressive,and drop test testing.The results of this research showed that the type of adhesive had a significant effect on the quality of the briquettes produced.Specimen Briquette_1 had better quality than commercial briquettes(Briquette_4)and other briquette specimens.The test results showed that Briquette_1 produced briquettes with better compressive strength and friability than the other specimens,at 6.95 N/mm^(2) and 4.44%,respectively.The moisture content,ash content,fixed carbon,and calorific value of Briquette_1 have met the requirements set by the Indonesian National Standard(SNI)number 01-6235-2000.Meanwhile,the volatile matter content and density of Briquette_1 are by the standards of Japan and the United States America(USA).

Preparation and emission property of scandia pressed cathode

Scandia pressed cathodes were prepared by powder metallurgy method using mixed powder of scandia doped tungsten and barium-calcium aluminates obtained by different mixing methods.The element distribution uniformity greatly affected the emission property.The powder prepared by ball-milling had small particle size and uniform distribution of different elements.This kind of powder was favorable for the chemical reaction among Ba,Ca aluminates,scandia and tungsten to take place sufficiently to form active substance which can improve the emission property.The emission current density of the cathode prepared with ball-milling powder was about 8 times higher than that prepared by manually mixing method,4 times higher than Os coated M-type cathode.The higher content of the active substance on the cathode surface prepared by ball-milling led to the better emission performance of the cathode.

Engineering of a Promoter Repressed by a Light-Regulated Transcription Factor in Escherichia coli

Light-regulated gene expression systems allow controlling gene expression in space and time with high accuracy.Contrary to previous synthetic light sensors that incorporate two-component systems which require localization at the plasma membrane,soluble one-component repression systems provide several advantageous characteristics.Firstly,they are soluble and able to diffuse across the cytoplasm.Secondly,they are smaller and of lower complexity,enabling less taxing expression and optimization of fewer parts.Thirdly,repression through steric hindrance is a widespread regulation mechanism that does not require specific interaction with host factors,potentially enabling implementation in different organisms.Herein,we present the design of the synthetic promoter P_(EL)that in combination with the light-regulated dimer EL222 constitutes a onecomponent repression system.Inspired by previously engineered synthetic promoters and the Escherichia coli lacZYA promoter,we designed P_(EL)with two EL222 operators positioned to hinder RNA polymerase binding when EL222 is bound.P_(EL)is repressed by EL222 under conditions of white light with a light-regulated repression ratio of five.Further,alternating conditions of darkness and light in cycles as short as one hour showed that repression is reversible.The design of the P_(EL)EL222 system herein presented could aid the design and implementation of analogous one-component optogenetic repression systems.Finally,we compare the P_(EL)-EL222 system with similar systems and suggest general improvements that could optimize and extend the functionality of EL222-based as well as other one-component repression systems.

Data Secure Transmission Model Based on Compressed Sensing and Digital Watermarking Technology

Since the Internet of Things（IoT） secret information is easy to leak in data transfer,a data secure transmission model based on compressed sensing（CS） and digital watermarking technology is proposed here. Firstly, for node coding end, the digital watermarking technology is used to embed secret information in the conventional data carrier. Secondly, these data are reused to build the target transfer data by the CS algorithm which are called observed signals. Thirdly, these signals are transmitted to the base station through the wireless channel. After obtaining these observed signals, the decoder reconstructs the data carrier containing privacy information. Finally, the privacy information is obtained by digital watermark extraction algorithm to achieve the secret transmission of signals. By adopting the watermarking and compression sensing to hide secret information in the end of node code, the algorithm complexity and energy consumption are reduced. Meanwhile, the security of secret information is increased.The simulation results show that the method is able to accurately reconstruct the original signal and the energy consumption of the sensor node is also reduced significantly in consideration of the packet loss.

Effect of thermal induced porosity on high-cycle fatigue and very high-cycle fatigue behaviors of hot-isostatic-pressed Ti-6Al-4V powder components

The present work reports the effect of thermal induced porosity(TIP)on the high-cycle fatigue(HCF)and very high-cycle fatigue(VHCF)behaviors of hot-isostatic-pressed(HIPed)Ti-6Al-4V alloy from gasatomized powder.The results show that the residual pores in the as-HIPed powder compacts present no obvious effect on the HCF life.The regrowth of the residual pores can be observed after solution heat treatment.The pore location ranks the most harmful for the fatigue life compared with the other initiating defects.The maximum stress intensity factors were calculated.The plastic zone size of fine granular area(FGA)is much less than the characteristic size of the microstructure,and the crucial size of the internal pores in this study is about 40μm.The failure types of fatigue specimens in the VHCF regime were classified,and the competition of different failure types was described based on the modified Poisson distribution.

Heat treatment of hot-isostatic-pressed 60NiTi shape memory alloy:Microstructure,phase transformation and mechanical properties

60NiTi alloy is considered to be a promising material for specialized bearing and gear applications due to its high hardness,strength,and low modulus.However,fabricating 60NiTi through conventional processing methods is challenging due to the brittleness and poor workability.In this study,60NiTi with high relative density was successfully fabricated directly from pre-alloyed powder through hot isostatic pressing.The effects of solution and aging treatments on microstructure and mechanical properties were systematically studied by advanced characterization techniques.The hot-isostatic-pressed 60NiTi showed low average hardness and elastic strain due to the formation of a soft Ni_(3)Ti phase and B2 NiTi matrix.Solution treatment above 1000℃dissolved the Ni_(3)Ti phase and promoted the formation of nanoscale Ni_(4)Ti_(3)precipitates,which significantly improved the hardness,strength,and elastic strain of 60NiTi.The formation of the Ni_(4)Ti_(3) phase can be mainly attributed to the driving forces induced by the chemical supersaturation and mechanical stress concentration.Finally,the phase transformation mechanisms during heat treatment and compression test were discussed.

Mechanical behaviour of wood compressed in radial direction:Part II.Influence of temperature and moisture content

This study investigated the influence of pressing temperature and moisture content on the me-chanical properties of wood compressed in radial direction.Jack pine(Pinus banksiana)and bal-sam poplar(Populus balsamifera)specimens were tested under a combination of pressing temper-ature(20℃,55℃,90℃,and 125℃)and wood moisture content(2%,7%,12%,and 17%).The yield stress(_(δ)y)and modulus of elasticity(MOE)of the specimens were determined from the stress-strain response.It was found that an increase in either pressing temperature or moisture content of wood generally caused a decrease in the mechanical properties for both species.The t-test results revealed that jack pine specimens are more sensitive to changes in pressing tem-perature and wood moisture content than balsam poplar.For jack pine specimens,at any of the pressing temperatures,the moisture content of 12%was found to be a crucial level to start a significant decrease in𝜎y and MOE,while at any of the moisture content,a change in temper-ature from 55℃to 90℃exhibited a significant change in𝜎y and MOE.The regression models developed can be used to predict𝜎y and MOE as a function of temperature and moisture content.

High temperature deformation behavior and processing map of hot isostatically pressed Ti-47.5Al-2Cr-2Nb-0.2W-0.2B alloy using gas atomization powders

The hot compressive deformation behavior of hot isostatically pressed Ti-47.5Al-2Cr-2Nb-0.2W-0.2B alloy using gas atomization powders was systematically investigated and the processing map was obtained in the temperature range of 1323-1473 Kand strain rate range of 0.001-0.5s^（-1）.The calculated activation energy in the above variational ranges of temperature and strain rate possesses a low activation energy value of approximately 365.6kJ/mol based on the constitutive relationship models developed with the Arrhenius-type constitutive model respectively considering the strain rate and deformation temperature.The hot working flow behavior during the deformation process was analyzed combined with the microstructural evolution.Meanwhile,the processing maps during the deformation process were established based on the dynamic material model and Prasad instability criterion under different deformation conditions.Finally,the optimal hot processing window of this alloy corresponding to the wide temperature range of 1353-1453 Kand the low strain rate of 0.001-0.1s^（-1） was obtained.

Effect of surface Nd-rich phase and oxygen content of melt-spun flakes on formation of coarse grains in hot-pressed Nd-Fe-B magnet

Nd-Fe-B hot-pressed(HP) magnet prepared from melt-spun MQU-F flakes features coarse grains(CG)with the average size of both 200 nm(CGS) and 700 nm(CGL) at flake boundary.The grain growth at the flake boundary of Nd2 Fe14B/α-Fe composite HP magnet before and after diffusion of low-melting-point Pr82Cu18 phase was investigated,revealing the indispensable role of surface RE-rich phase of meltspun flakes in the formation of CG in HP magnet.The dominant role of surface oxygen content of melt-spun flakes in the formation of CGL has been clarified with etching method.The HP magnet prepared from the etched flakes with dramatically decreased oxygen content exhibits the CG regions merely with homoge neous equiaxed CGS at flake boundary.Consequently,the coercivity(μ0 Hc) shows significant increase while remanent magnetization(μ0 Mr) inappreciable change.Further investigation with sieving method reveals the elimination of CGL via removal of the fine Nd-Fe-B flakes smaller than 54 μm due to their much higher oxygen content,confirming the dominant role of oxygen content in the formation of CGL.The quantitative analysis on the magnetic properties of the above HP magnets reveals the monotonic increase of coercivity(μ0 Hc) and negligible change of remanent magnetization(μ0 Mr) with decreased oxygen contents of Nd-Fe-B flakes.The maximum value of coercivity(μ0 Hc) increases from2.26 to 2.47 T as the oxygen content decreases from 0.1692 wt% to 0.079 wt%.

Effect of the capsule on deformation and densification behavior of nickel-based superalloy compact during hot isostatic pressing

The Shima yield criterion used in finite element analysis for nickel-based superalloy powder compact during hot isostatic pressing(HIP) was modified through uniaxial compression experiments. The influence of cylindrical capsule characteristics on FGH4096M superalloy powder compact deformation and densification behavior during HIP was investigated through simulations and experiments. Results revealed the simulation shrinkage prediction fitted well with the experimental shrinkage including a maximum shrinkage error of 1.5%. It was shown that the axial shrinkage was 1.7% higher than radial shrinkage for a cylindrical capsule with the size of ∮50 mm × 100 mm due to the force arm difference along the axial and radial direction of the capsule. The stress deviated from the isostatic state in the capsule led to the uneven shrinkage and non-uniform densification of the powder compact. The ratio of the maximum radial displacement to axial displacement increased from0.47 to 0.75 with the capsule thickness increasing from 2 to 4 mm. The pressure transmission is related to the capsule thickness, the capsule material performance, and physical parameters in the HIP process.

Effects of microstructure characteristics on the tensile properties and fracture toughness of TA15 alloy fabricated by hot isostatic pressing

Powder hot isostatic pressing(HIP) is an effective method to achieve near-net-shape manufacturing of high-quality complex thinwalled titanium alloy parts, and it has received extensive attention in recent years. However, there are few reports about the microstructure characteristics on the strengthening and toughening mechanisms of powder hot isostatic pressed(HIPed) titanium alloys. Therefore, TA15powder was prepared into alloy by HIP approach, which was used to explore the microstructure characteristics at different HIP temperatures and the corresponding tensile properties and fracture toughness. Results show that the fabricated alloy has a “basket-like structure” when the HIP temperature is below 950℃, consisting of lath clusters and surrounding small equiaxed grains belts. When the HIP temperature is higher than 950℃, the microstructure gradually transforms into the Widmanstatten structure, accompanied by a significant increase in grain size. The tensile strength and elongation are reduced from 948 MPa and 17.3% for the 910℃ specimen to 861 MPa and 10% for the 970℃ specimen.The corresponding tensile fracture mode changes from transcrystalline plastic fracture to mixed fracture including intercrystalline cleavage.The fracture toughness of the specimens increases from 82.64 MPa·m^(1/2)for the 910℃ specimen to 140.18 MPa·m^(1/2)for the 970℃ specimen.Specimens below 950℃ tend to form holes due to the prior particle boundaries(PPBs), which is not conducive to toughening. Specimens above 950℃ have high fracture toughness due to the crack deflection, crack branching, and shear plastic deformation of the Widmanstatten structure. This study provides a valid reference for the development of powder HIPed titanium alloy.

Wear resistance performance of high entropy alloy–ceramic coating composites synthesized via a novel combined process

Titanium nitride(TiN), characterized by its high hardness and strength, was widely used as ceramic coating to improve the wear resistance of matrix materials. In this work, AlCrFeNiTi_(x) high-entropy alloy(HEA) powders were synthesized by direct electrochemical reduction in molten salt from the mixed metal oxides. Then,TiN ceramic coating on the AlCrFeNiTi_x bulk HEA containing the topologically close-packed(TCP) phase(σphase, Laves phase, and Ti_(3)Al phase) was prepared by vacuum hot pressing sintering, where nitride element come from boron nitride parting agent sprayed on the graphite mold. The effect of titanium content on the crystal structure, microstructure, hardness, and wear resistance of the products were investigated by X-ray diffraction, field emission scanning electron microscope, field emission electron-probe microanalysis,Vickers hardness tester, and friction–abrasion testing machine. The bulk HEAs exhibit excellent hardness and its hardness increases significantly with the increase of titanium content. The wear mechanism changes from both of predominantly delamination and accompanied oxidative wear to single delamination wear,which is due to ultra-high melting point and high hot hardness of TiN, that can effectively prevent the oxidation and deformation of the worn surface. Formation of the ceramic coatings containing the TiN second phase and TCP phase are the key factor to AlCrFeNiTi_x alloy with the excellent hardness and wear properties.

Simple shear extrusion versus equal channel angular pressing:A comparative study on the microstructure and mechanical properties of an Mg alloy

Two severe plastic deformation(SPD)techniques of simple shear extrusion(SSE)and equal channel angular pressing(ECAP)were employed to process an extruded Mg-6Gd-3Y-1.5Ag(wt%)alloy at 553 K for 1,2,4 and 6 passes.The microstructural evolutions were studied by electron back scattered diffraction(EBSD)analysis and transmission electron microscopy(TEM).The initial grain size of 7.5μm in the extruded alloy was reduced to about 1.3μm after 6 SPD passes.Discontinuous dynamic recrystallization was suggested to be operative in both SSE and ECAP,with also a potential contribution of continuous dynamic recrystallization at the early stages of deformation.The difference in the shear strain paths of the two SPD techniques caused different progression rate of dynamic recrystallization(DRX),so that the alloys processed by ECAP exhibited higher fractions of recrystallization and high angle grain boundaries(HAGBs).It was revealed that crystallographic texture was also significantly influenced by the difference in the strain paths of the two SPD methods,where dissimilar basal plane texture components were obtained.The compression tests,performed along extrusion direction(ED),indicated that the compressive yield stress(CYS)and ultimate compressive strength(UCS)of the alloys after both SEE and ECAP augmented continuously by increasing the number of passes.ECAP-processed alloys had lower values of CYS and UCS compared to their counterparts processed by SSE.This difference in the mechanical responses was attributed to the different configurations of basal planes with respect to the loading direction(ED)of each SPD technique.