Data-driven intelligent monitoring system for key variables in wastewater treatment process

In wastewater treatment process(WWTP), the accurate and real-time monitoring values of key variables are crucial for the operational strategies. However, most of the existing methods have difficulty in obtaining the real-time values of some key variables in the process. In order to handle this issue, a data-driven intelligent monitoring system, using the soft sensor technique and data distribution service, is developed to monitor the concentrations of effluent total phosphorous(TP) and ammonia nitrogen(NH_4-N). In this intelligent monitoring system, a fuzzy neural network(FNN) is applied for designing the soft sensor model, and a principal component analysis(PCA) method is used to select the input variables of the soft sensor model. Moreover, data transfer software is exploited to insert the soft sensor technique to the supervisory control and data acquisition(SCADA) system. Finally, this proposed intelligent monitoring system is tested in several real plants to demonstrate the reliability and effectiveness of the monitoring performance.

A modified active disturbance rejection control for a wastewater treatment process

Waste water treatment process(WWTP)control has been attracting more and more attention.However,various undesired factors,such as disturbance,uncertainties,and strong nonlinear couplings,propose big challenges to the control of a WWTP.In order to improve the control performance of the closed-loop system and guarantee the discharge requirements of the effluent quality,rather than take the model dependent control approaches,an active disturbance rejection control(ADRC)is utilized.Based on the control signal and system output,a phase optimized ADRC(POADRC)is designed to control the dissolved oxygen and nitrate concentration in a WWTP.The phase advantage of the phase optimized extended state observer(POESO),convergence of the POESO,and stability of the closed-loop system are analyzed from the theoretical point of view.Finally,a commonly accepted benchmark simulation model no.1.(BSM1)is utilized to test the POESO and POADRC.Linear active disturbance rejection control(LADRC)and the suggested proportion-integration(PI)control are taken to make a comparative research.Both system responses and performance index values confirm the advantage of the POADRC over the LADRC and the suggested PI control.Numerical results show that,as a result of the leading phase of the total disturbance estimation,the POESO based POADRC is an effective and promising way to control the dissolved oxygen and nitrate concentration so as to ensure the effluent quality of a WWTP.

Source,Process and End Treatment Technology of Volatile Organic Compounds in Oil Storage

Oil storage is a source of volatile organic compounds( VOCs). Volatile organic compounds can cause different damages to the environment,animals and plants. Therefore, it is important to control the discharge of VOCs in oil storage. In this paper,the control technology of sources of VOCs pollution in oil storage was analyzed from the source,process and end treatment,and measures for the prevention and control of VOCs pollution in oil storage were proposed.

Pollutants removal and simulation model of combined membrane process for wastewater treatment and reuse in submarine cabin for long voyage

A laboratory scale test was conducted in a combined membrane process （CMP） with a capacity of 2.91 m3/d for 240 d to treat the mixed wastewater of humidity condensate, hygiene wastewater and urine in submarine cabin during prolonged voyage. Removal performance of chemical oxygen demand （COD）, ammonia nitrogen （NH4^＋-N）, turbidity and anionic surfactants （LAS） was investigated under different conditions. It was observed that the effluent COD, NH4^＋-N, turbidity and LAS flocculated in ranges of 0.19-0.85 mg/L, 0.03-0.18 mg/L, 0.0-0.15 NTU and 0.0-0.05 mg/L, respectively in spite of considerable fluctuation in corresponding influent of 2120-5350 mg/L, 79.5-129.3 mg/L, 110-181.1NTU and 4.9-5.4 mg/L. The effluent quality of the CMP could meet the requirements of mechanical water and hygiene water according to the class I water quality standards in China （GB3838-2002）. The removal rates of COD, NH4^＋-N, turbidity and LAS removed in the MBR were more than 90%, which indicated that biodegradation is indispensable and plays a major role in the wastewater treatment and reuse. A model, built on the back propagation neural network （BPNN） theory, was developed for the simulation of CMP and produced high reliability. The average error of COD and NH4^＋-N was 5.14% and 6.20%, respectively, and the root mean squared error of turbidity and LAS was 2.76% and 1.41%, respectively. The results indicated that the model well fitted the laboratory data, and was able to simulate the removal of COD, NH4^＋-N, turbidity and LAS. It also suggested that the model proposed could reflect and manage the operation of CMP for the treatment of the mixed wastewaters in submarine.

Treatment of pharmaceutical wastewater containing recalcitrant compounds in a Fenton-coagulation process

The advanced treatment using integrated Fenton＇s reaction and coagulation process was investigated in this study. Before the advancement, the pharmaceutical wastewater containing lincomycin hydrochloride was pretreated by UASB （upflow anaerobic sludge bed） and a SBR （sequencing batch reactor） process. The residual recalcitrant compounds, measured by gas chromatographymass spectrometry （GC-MS）, mainly consisted of alcohols, phenols, and nitrogenous and sulfur compounds. The experimental results indicated that when the Fenton＇s reaction was conducted at pH=3.0, H2O2CODOcr=0.27, H2O2/Fe^2＋=3：1 and 30 min of reaction time, and the coagulation process operated at a sulfate aluminum concentration of 800 mg/L and pH value of 5.0, the color and COD in the wastewater decreased by 94% and 73%, respectively; with a finale COD concentration of 267 mg/L and color level of 40 units, meeting the secondary standard of GB8978-1996 for industrial wastewater.

Extraction process of chlorogenic acid in flos lonicerae by enzymatic treatment

A new method of extracting chlorogenic acid from flos lonicerae, and treating the materials with enzyme before being extracted by ethanol is developed, and the optimum conditions are also investigated in detail. Three important factors, enzyme dosage, treatment time and treatment temperature are adapted to optimize the extraction process. The experimental results show that the extract yield of flos lonicerae and chlorogenic acid can be obviously increased by the cellulase treatment, 61.5 mg chlorogenic acid is obtained from 1.00 g flos lonicerae at most. The optimal temperature of enzymatic treatment is 40 50 ℃. Compared with the use of single cellulase, the combined treatment of cellulase and pectinase increase the extract yield obviously but fail to improve that of chlorogenic acid.

Review on Optimization of Drinking Water Treatment Process

In the drinking water treatment processes, the optimization of the treatment is an issue of particular concern. In general, the process consists of many units as settling, coagulation, flocculation, sedimentation, filtration and disinfection. The optimization of the process consists of some measures to decrease the managing and monitoring expenses and improve the quality of the produced water. The objective of this study is to provide water treatment operators with methods and practices that enable to attain the most effective use of the facility and in consequence optimize the cubic meter price of the treated water. This paper proposes a review on optimization of drinking water treatment process by analyzing all of the water treatment units and gives some solutions in order to maximize the water treatment performances without compromising the water quality standards. Some practical solutions and methods are performed in the water treatment plant located in the middle of Morocco (Meknes).

Reducing Efficiencies of the Commonly Used Heat Treatment Methods and Fermentation Processes on Aflatoxin M1 in Naturally Contaminated Fresh Cow Milk

The reducing efficiencies of the commonly used heat treatment methods and fermentation processes on aflatoxin M1 (AFM1) in Nigeria were investigated. Seventy samples of fresh cow milk from both conventional and traditional dairy cattle herds were collected and analyzed for the determination of AFM1 using Cobra-cell incorporated high performance liquid chromatography. Of these analyzed samples, 56 (80.0%) tested positive for AFM1 out of which 3 milk samples with high AFM1 concentrations were selectively pooled and subjected to varied conditions of heat treatments and fermentation processes using both indigenized and exotic strains of lactic acid bacteria (Lactobacillus bulgaricus + Streptococcus thermophilus and L. rhamnosus and L. plantarum) as starter cultures respectively. Both processes used either singly or combined, demonstrated high degrees of reducing effects on AFM1 levels. Sterilization of the milk at 121?C and 80?C under the same condition of time (15 - 20) min showed significant reduction of up to 58.8% (p 0.05) in the level of AFM1 when compared with the initial mean AFM1 concentration of the untreated fresh milk. The situation was however different around the boiling temperature of 100?C at which point the level of AFM1 reduction was found to be inconsistent. The indigenized combined strains showed some slight margins of AFM1 reduction in the proportions of (20.5, 30.8 and 43.9)% over and above that of the exotic strains (17.4, 30.0 and 41.1)% in 12 h, 48 h and 72 h of fermentation respectively. Generally, fermentation alone showed lower reduction of AFM1 in milk from 24.5% to 43.9% compared with the reducing activities of (35.4 to 58.8)% when heat-treated milk samples were subsequently subjected to varied fermentation conditions.

Mutagenicity and Genotoxicity of Organic Extracts from Finished Water with Different Treatment Process

Purification of surface water is widely practiced with conventional water treatment processes like coagulation-flocculation, sedimentation, filtration,and disinfection. Some reports have specified that conventional wastewater purification processes do not effectively remove many chemical contaminants,

Petro-chemical wastewater treatment by biological process

In order to study the feasibility of treating petro chemical wastewater by the combination of anaerobic and aerobic biological process, a research of treating wastewater in UASB reactor and aeration basin has been conducted. The test results shows that under moderate temperature, with 5\^2 kgCOD/(m\+3·d) volumetric load of COD Cr in the UASB reactor and 24h of HRT, 85% removal rate of BOD 5 and 83% of COD \{Cr\} and 1\^34 m\+3/(m\+3·d) volumetric gas production rate can be obtained respectively. The aerobic bio degradability can be increased by 20%—30% after the petro chemical wastewater has been treated by anaerobic process. As Ns=0\^45 kgCOD/(kgMLSS·d), HRT=4h in the aeration tank, 94% removal rate of BOD 5, 93% of COD \{Cr\}, 98\^8% total removal rate of COD \{Cr\} and 99% removal rate of BOD 5 can be reached.

Effects of Heat Treatment on Hardness and Dry Wear Properties of a Semi-Solid Processed Fe-27 wt pct Cr-2.9 wt pct C Cast Iron

EfFects of heat treatments on hardness and dry wear properties of a semi-solid processed Fe-26.96 wt pct Cr- 2.91 wt pct C cast iron were studied. Heat treatments included tempering at 500℃, destabilisation at 1075℃ and destabilisation at 1075℃ plus tempering at 500℃, all followed by air cooling. Electron microscopy revealed that, in the as-cast condition, the primary proeutectic austenite was round in shape while the eutectic M7C3 carbide was found as radiating clusters mixed with directional clusters. Tempering did not change the microstructure significantly when observed by scanning or transmission electron microscopy. Destabilisation followed by air cooling led to a precipitation of secondary M23C6 carbide and a transformation of the primary austenite to martensite. Precipitation behaviour is comparable to that observed in the conventionally cast iron. Tempering after destabilisation resulted in a higher amount of secondary carbide precipitation within the tempered martensite in the eutectic structure. Vickers macrohardness and microhardness in the proeutectic zones were measured. Dry wear properties were tested by using a pin-on-disc method. The maximum hardness and the lowest dry wear rate were obtained from the destabilisation-plus-tempering heat treatment due to the precipitation of secondary carbides within the martensite matrix and a possible reduction in the retained austenite.

The Integration of Vacuum Brazing into Heat Treatment - A Progressive Combined Process

The continuous constructive challenge to improve the functionality and efficiency of components always results in higher demands on production engineering, against the background of the generally increasing cost pressure. In many cases, you will just succeed in producing competitive and innovative products by combining and coupling of different procedures to an independent (hybrid) technology. The use of hybrid procedures for metal joining and heat treatment of metallic materials finds more and more industrial fields of application. Modern vacuum lines with integrated pressurized gas quenching are considered high-performance and flexible means of production for brazing and heat treatment tasks as well in the turbine industry as in the mould making and tool manufacturing industry. In doing so, the heat treatment is coupled with the brazing cycle in a combined process so that the brazing temperatures and soak times are adapted to the necessary temperatures and times for solution heat treatment and austeniting. This user-oriented article describes on the one hand examples of brazing of turbine components, but above all the practical experience from the plastics processing industry, where the requirement for a high-efficient cooling of injection moulding dies gains more and more importance. The combined procedure "Vacuum Brazing and Hardening" offers plenty of possibilities to produce mould inserts with an efficient tempering system in an economic way.

Empirical Investigation of Treatment of Sour Gas by Novel Technology: Energy Optimization

The sour gas sweetening is one of the main processes in gas industries. Gas sweetening is done through chemical processes. Therefore, it requires high cost and energy. The results show that increasing the operating temperature increases the mass transfer coefficient and increases the mass transfer rate. Theoretical and experimental data show that sulfur removal in 4.5 W magnetic field is desirable. The increase in sulfur removal percentage in the magnetic field of 4.5 W and 6.75 W is about 16.4% and 15.2%, respectively. According to the obtained results, the effect of temperature increase from 18.8°C to 23.4°C is more evident than the effect of temperature change from 23.4°C to 32.2°C. Because more thermal energy is needed to provide higher temperatures. Therefore, the temperature of 23.4°C is reported as the optimal temperature. The results of this research show that the percentage of sulfur removal is also high at this temperature.

A NEW HEAT-TREATMENT PROCESS FOR 2014 ALUMINUM ALLOY AND ITS MECHANISM

The plan of heat-treatment process for 2014Al alloy is designed using orthogonal method, the heat-treatment experiments are made and the mechanical properties are tested according to the designed plan. The effect of solid solution temperature, ageing temperature, ageing time on microscopic mechanism of the mechanical properties of the 2014Al alloy is studied using microscope, transmission electron microscope. The best heat treatment process of the 2014Al alloy is developed. The experimental results indicate that the strength σb, yield stress σ0.2, percentage elongation δ of the alloy reach separately 490～500 MPa, 450～490 MPa, 10～12％ adopting the new heat treatment process. Compared with GB, the strength increases 20～30％, the percentage elongation increases 30～40％. The mechanism of the new heat-treatment process is also discussed.

Intended process water management concept for the mechanical biological treatment of municipal solid waste

Accumulating operational experience in both aerobic and anaerobic mechanical biological waste treatment （MBT） makes it increasingly obvious that controlled water management would substantially reduce the cost of MBT and also enhance resource recovery of the organic and inorganic fraction. The MBT plant at Gescher, Germany, is used as an example in order to determine the quantity and composition of process water and leachates from intensive and subsequent rotting, pressing water from anaerobic digestion and scrubber water from acid exhaust air treatment, and hence prepare an MBT water balance. The potential of, requirements for and limits to internal process water reuse as well as the possibilities of resource recovery from scrubber water are also examined. Finally, an assimilated process water management concept with the purpose of an extensive reduction of wastewater quantity and freshwater demand is presented.

城市污水处理过程污泥膨胀识别与抑制综述

污泥膨胀是活性污泥法污水处理过程中常见的一类异常工况,且具有严重危害性,研究污泥膨胀的识别和抑制方法对城市污水处理过程正常运行意义重大.本文主要针对城市污水处理过程中污泥膨胀的识别和抑制方法进行综述.首先,文章概述了城市污水处理过程,介绍了污泥膨胀的概念、主要特点、类型和成因;其次,概述了基于微生物生理特征、机理模型、图像识别和数据驱动的污泥膨胀识别方法,分析其发展现状并指出优缺点;然后,概述了基于过程调控和机理特征的污泥膨胀抑制方法,分析其发展现状并对比优缺点;最后,总结全文,指出了城市污水处理过程污泥膨胀识别和抑制面临的主要问题,并对其研究趋势进行了展望.

Posterior articular process approach for the treatment of upper lumbar disc herniation

Objective To investigate the feasibility and surgical effects of posterior articular process approach for the treatment of L1-L3 lumbar disc herniation.Methods A retrospective study,of17patients with upper lumbar intervertebml disc

过碳酸盐高级氧化技术在水处理中的研究进展

近年来,活化过碳酸盐高级氧化技术具有低成本、安全、稳定等特点,已广泛用于处理水中的各类有机污染物,有望成为一种新兴的环境友好型水处理技术。该文介绍了活化过碳酸盐降解有机污染物的机理;系统综述了均相活化、非均相活化、物理活化、其他活化过碳酸盐的活化方法与活化反应机理;总结了过碳酸盐高级氧化法在水处理中的应用,重点阐述了过碳酸盐高级氧化法在去除水中的有机污染物、膜污染控制、污泥脱水、污泥厌氧消化等方面的应用研究现状;最后,指出目前水处理研究领域活化过碳酸盐高级氧化技术存在的问题,并对未来的重点研究方向进行了展望。

ANALYSIS AND IMPROVEMENT ON LANDFILL LEACHATE TREATMENT PROCESS OF MUNICIPAL SOLID WASTE

According to different mechanism of microbial degradation of organics, this article divided the treatment processes of garbage landfill into four kinds, analyzed each kind of the treatment leachate process and presented a better improved process. (Author abstract) 4 Refs.

Effects of Fillerwire Composition along with Different Pre- and Post-Heat Treatment on Mechanical Properties of AISI 4130 Welded by the GTAW Process

This research intends to find out the optimal mechanical properties of AISI 4130 steel welded by the GTAW process. Six test plates were joined by two types of filler wire with similar chemical composition to the base metal, and with lower carbon content and slightly higher alloy elements content compared to the first one. Test plates then exerted three different pre-heat and post-heat treatments on both groups. The three types of heat treatments were alternatively without pre-heat and post-heat, with pre-heat only, and finally with pre-heat and post-heat. Tensile, side bends and impact tests (for weld zone and HAZ) have been conducted. Results show that using low-carbon filler wire along with pre- and post-heat resulted in outstanding mechanical properties.