Productivity analysis of horizontal wells intercepted by multiple finite-conductivity fractures

Horizontal wells in the anisotropic reservoirs can be stimulated by hydraulic fracturing in order to create multiple finite-conductivity vertical fractures. Several methods for evaluating the productivity of the horizontal wells have been presented in the literature. With such methods, however, it is still difficult to obtain an accurate result. This paper firstly presents the dimensionless conductivity theory of vertical fractures. Then models for calculating the equivalent wellbore radius and the skin factor due to flow convergence to the well bore are proposed after analyzing the steady-state flow in porous reservoirs. By applying the superposition principle to the pressure drop, a new method for evaluating the productivity of horizontal wells intercepted by multiple finite-conductivity fractures is developed. The influence of fracture conductivity and fracture half length on the horizontal well productivity is quantitatively analyzed with a synthetic case. Optimum fracture number and fracture space are further discussed in this study. The results prove that the method outlined here should be useful to design optimum fracturing of horizontal wells.

GROWTH,PRODUCTIVITY AND NUTRIENT ANALYSIS OF CUPRESSUS GIGANTCA

Cupressus gigantca is naturally distrib-uted in the lower-middle reaches of theYaluzangbu River.It’s maximum age canreach up to 1,000 years,diameter at breastheigh (DBH) 400cm and height 45m.The

Development and Application of a Production Data Analysis Model for a Shale Gas Production Well

This paper presents the development and application of a production data analysis software that can analyze and forecast the production performance and reservoir properties of shale gas wells.The theories used in the study were based on the analytical and empirical approaches.Its reliability has been confirmed through comparisons with a commercial software.Using transient data relating to multi-stage hydraulic fractured horizontal wells,it was confirmed that the accuracy of the modified hyperbolic method showed an error of approximately 4%compared to the actual estimated ultimate recovery(EUR).On the basis of the developed model,reliable productivity forecasts have been obtained by analyzing field production data relating to wells in Canada.The EUR was computed as 9.6 Bcf using the modified hyperbolic method.Employing the Pow Law Exponential method,the EUR would be 9.4 Bcf.The models developed in this study will allow in the future integration of new analytical and empirical theories in a relatively readily than commercial models.

Chemical Analysis Method for Carbon Bearing Refractory Products——Determination of the Total Carbon by Combustion Gravimetric Method

GB/T 13245-91 1 Theme and Scope This standard specifies the method abstract, reagents, apparatus, specimen, analyzing procedure, result calculation and permissible tolerance used for determination of the total carbon with combustion gravimetric method.

Performances Analysis and Developmental Strategy of Hexi Cashmere Goats

The productive performances of Hexi cashmere goats for breeding nucleus groups and producing groups in different production areas were reviewed. At the same time, the productive performances were analyzed. Moreover, the existing problems and solving methods were put forward. In addition, the Hexi cashmere goats was an ancient and native breed, and it was necessary to further improve its productive performance to protect and utilize the breed resource effectively.

Maximizing the Benefit of Rate Transient Analysis for Gas Condensate Reservoirs

In recent years,many trials have been made to use the Rate Transient Analysis(RTA)techniques as a method to describe the gas condensate reservoirs.The problem with using these techniques is the multi-phase behavior of the gas condensate reservoirs.Therefore,the Pressure Transient Analysis(PTA)is commonly used in this case to analyze the reservoir parameters.In this paper,we are going to compare the results of both PTA and RTA of three wells in gas condensate reservoirs.The comparison showed a great match between the results of the two mentioned techniques for the first time using a reference GOR of 75,000 SCF/STB.Therefore,we concluded that we could depend on RTA instead of PTA to spare the cost associated with the PTA in the gas condensate reservoirs.

Chemical Analysis Method for Carbon Bearing Refractory Products——Determination of Magnesium Oxide Content by CyDTA Volumetric Method

This standard specifies the method summary, reagents, apparatus, sampling, procedure, test results calculation and permissible tolerance of the determination of magnesium oxide by CyDTA volumetric method.

Workshop on Simulation and Systems Analysis for Rice Production(SARP) held at CNRRI

SARP Workshop on risk analysis of agroecological zonation and optimization of crop rotation was held at CNRRI’s research center on 24—27 Oct, 1995. Experts from Philippines, India, China, and IRRI were present in the workshop. Participants exchanged the research results on the field of land use, soil erosion. optimization of rice—wheat, rice—peanut, rice—corn cropping system in the different environments, risk analysis of rice based cropping system, nitrogen balance in rice based cropping system with system approach, demonstrated models used in their studies, and discussed the ongoing cooperative research.

Simultaneous removal of 1,2-dichlorobenzene and furan over Mn-Ce-Fe oxide catalyst:Catalytic activity and product analysis

The Mn-Ce-Fe mixed oxide(MCFe)was prepared by co-precipitation and the catalytic performance was tested by using 1,2-dichlorobenzene(1,2-DCB)and furan as model molecules of PCDD/F.The effect of O_(2)concentration,SO_(2) and NO on the catalytic activity was studied.At 270℃,the MCFe oxide catalyst presents significant simultaneous removal efficiency of 75.25%and 100%for 1,2-DCB and furan,respectively.Brunauer-Emmett-Teller(BET)method(BET),X-ray diffraction(XRD),scanning electron microscopy(SEM),X-ray photoelectron spectroscopy(XPS),Fourier transform infrared spectroscopy(FTIR),H_2-temperature programmed reduction(H_(2)-TPR),NH_(3)-temperature programmed desorption(NH_3-TPD)and O_(2)-TPD were used to characterize the catalysts before and after the reaction.Competition tests suggest that the oxidation behavior of furan occurred prior to that of 1,2-DCB.According to the intermediate products detected by gas chromatography-mass spectrometry(GC-MS),the by-products include chlorinated hydrocarbons,long-chain hydrocarbons,ketone,etc.Possible catalytic oxidation reaction paths are proposed.

Production Capacity Evaluation of Horizontal Shale Gas Wells in Fuling District

One of the important indicators of shale gas reservoir excavation is capacity evaluation,which directly affects whether large-scale shale gas reservoirs can be excavated.Capacity evaluation is the basis of system analysis and dynamic prediction.Therefore,it is particularly important to conduct capacity evaluation studies on shale gas horizontal wells.In order to accurately evaluate the horizontal well productivity of shale gas staged fracturing,this paper uses a new method to evaluate the productivity of Fuling shale gas.The new method is aimed at the dynamic difference of horizontal wells and effectively analyzes the massive data,which are factors affecting the productivity of shale gas horizontal wells.According to the pressure system,production dynamic characteristics,well trajectory position,fracturing transformation mode and penetration depth,32 wells were divided into four types.Then,based on the classification,the principal component analysis methods can be used to evaluate the horizontal well productivity of shale gas.The new method of capacity evaluation has improved the accuracy by 10.25%compared with the traditional method,which provides a theoretical basis for guiding the efficient development of the horizontal wells of Fuling shale gas.

Toluene removal characteristics by a superimposed wire-plate dielectric barrier discharge plasma reactor

A superimposed wire-plate dielectric barrier discharge reactor was used to remove toluene in this study. The effects of oxygen content, gas flow rate, gas initial concentration and with/without catalyst on toluene decomposition were investigated. It was found that an optimal toluene removal was achieved when the oxygen content was about 5%. Under this condition, the highest toluene removal efficiency of 80.8% was achieved when the gas concentration was 80 mg/m^3. The toluene removal efficiency decreased with the increase of the gas flow rate and the initial concentration of toluene. In addition, the ozone concentration decreased with the increase of the initial concentration of toluene. It suggested that combining DBD （dielectric barrier discharge） with Co3O4/Al2O3/foam nickel catalyst in-situ could improve the toluene removal efficiency and suppress ozone formation. Products analysis showed that the main products were CO and CO2 when oxygen was more than 5%.

Classification of carbonate gas condensate reservoirs using well test and production data analyses

Carbonate reservoir patterns play an important role in the production performance of oil and gas wells,and it is usually classified through static data analysis which cannot reflect the actual well performance.This paper takes the Tazhong No.1 gas field in the Tarim Basin,China as an example to investigate the classification of carbonate reservoirs.The classification method mainly combines well test analysis with production analysis—especially the Blasingame type curve method.Based on the characteristics of type curves for well test analysis and the Blasingame method,the relationship between the type curves and reservoir pattern was established.More than 20 wells were analyzed and the reservoirs were classified into 3 major patterns with 7 sub-classes.Furthermore,the classification results were validated by dynamic performance analysis of wells in the Tazhong No.1 gas field.On the basis of the classification results,well stimulation（i.e.water flooding in a single well） was carried out in three volatile-oil wells,and the oil recovery increased by up to 20%.

Mine production index(MPI)-extension of OEE for bottleneck detection in mining

Although mining production depends on various equipments, significant amount of production loss can be attributed a specific equipment or fleet. Bottleneck is defined not only by production loss but also by our satisfaction from the equipment. The user satisfaction could be measured as machine effectiveness.Mining literatures on performance improvement and optimization of equipment operations assert importance of availability, utilization and production performance as key parameters. These three parameters are useful for evaluating effectiveness of equipment. Mine production index(MPI), which can represent the effect of these factors, has been applied for continuous operation in mining. MPI uses Fuzzy Delphi Analytical Hierarchy Process to determine importance of each three parameter for individual equipment. A case study in a Swedish open pit mine was done to evaluate the field application of MPI.The results reveal that crusher is the bottleneck equipment in studied mine. As a methodical approach,an algorithm which uses MPI and detects bottleneck in continuous mining operation has been proposed.

Numerical investigation on the effect of gas parameters on ozone generation in pulsed dielectric barrier discharge

Pulsed dielectric barrier discharge is a promising technology for ozone generation and is drawing increasing interest. To overcome the drawback of experimental investigation, a kinetic model is applied to numerically investigate the effect of gas parameters including inlet gas temperature, gas pressure, and gas flow rate on ozone generation using pulsed dielectric barrier discharge. The results show that ozone concentration and ozone yield increase with decreasing inlet gas temperature, gas pressure, and gas flow rate. The highest ozone concentration and ozone yield in oxygen are about 1.8 and 2.5 times higher than those in air, respectively. A very interesting phenomenon is observed： the peak ozone yield occurs at a lower ozone concentration when the inlet gas temperature and gas pressure are higher because of the increasing average gas temperature in the discharge gap as well as the decreasing reduced electric field and electron density in the microdischarge channel. Furthermore, the sensitivity and rate of production analysis based on the specific input energy （SIE） for the four most important species 03, O, O（1D）, and O2（b1∑） are executed to quantitatively understand the effects of every reaction on them, and to determine the contribution of individual reactions to their net production or destruction rates. A reasonable increase in SIE is beneficial to ozone generation. However, excessively high S1E is not favorable for ozone production.

XML-based Data Processing in Network Supported Collaborative Design

In the course of network supported collaborative design, the data processing plays a very vital role. Much effort has been spent in this area, and many kinds of approaches have been proposed. Based on the correlative materials, this paper presents extensible markup language （XML） based strategy for several important problems of data processing in network supported collaborative design, such as the representation of standard for the exchange of product model data （STEP） with XML in the product information expression and the management of XML documents using relational database. The paper gives a detailed exposition on how to clarify the mapping between XML structure and the relationship database structure and how XML-QL queries can be translated into structured query language （SQL） queries. Finally, the structure of data processing system based on XML is presented.

Lag times in toe-to-heel air injection(THAI)operations explain underlying heavy oil production mechanisms

From a time value of revenue point of view,it is preferred that the time between reservoir stimulation and oil production response is small.Heavy oil combustion processes have a lag time between air injection and liquid production,but the common practice in production data analysis uses simultaneous injection and production data when seeking a relationship between them.In this research,the time scales of production for the Kerrobert toe-to-heel air injection(THAI)heavy oil project in Saskatchewan,Canada,is analyzed by using cross correlation analysis,i.e.time delay analysis between air injection and oil production.The results reveal two time scales with respect to production response with two distinctive recovery mechanisms:(1)a short time scale response(nearly instantaneous)where oil production peaks right after air injection(directly after opening production well)reflecting cold heavy oil production mechanisms,and(2)a longer time scale(of order of 100-300 days)response where peak production occurs associated with the collective phenomena of air injection,heat generating reactions,heat transfer,and finally,heated mobilized heavy oil drainage to the production well.This understanding of the two time scales and associated production mechanisms provides a basis for improving the performance of THAI.

Investigation on Atmospheric Corrosiveness in Hainan Province

According to the results of four-year exposure tests for carbon steel samples in Hainan province,the influences of meteorological factors and Cl~- on atmospheric corrosion were investigated.The feature of atmospheric corrosion in this area was summarized.A corrosive map for the area was drawn.The corrosion products on carbon steel at some typical places were analyzed by XRD and XPS.

Decomposition analysis applied to energy and emissions:A literature review

Decomposition analysis has been widely used to assess the determinants of energy and CO_(2)emissions in academic research and policy studies.Both the methodology and application of decomposition analysis have been largely improved in the past decades.After more than 50 years’developments,decomposition studies have become increasingly sophisticated and diversified,and tend to converge internally and integrate with other analytical approaches externally.A good understanding of the literature and state of the art is critical to identify knowledge gaps and formulate future research agenda.To this end,this study presents a literature survey for decomposition analysis applied to energy and emission issues,with a focus on the period of 2016–2021.A review for three individual decomposition techniques is first conducted,followed by a synthesis of emerging trends and features for the decomposition analysis literature as a whole.The findings are expected to direct future research in decomposition analysis.