A novel strategy was developed to prepare the methacrylic gelatin-dopamine(GelMA-DA)/Ag nanoparticles(NPs)/graphene oxide(GO) composite hydrogels with good biocompatibility,mechanical properties,and antibacterial acti...A novel strategy was developed to prepare the methacrylic gelatin-dopamine(GelMA-DA)/Ag nanoparticles(NPs)/graphene oxide(GO) composite hydrogels with good biocompatibility,mechanical properties,and antibacterial activity.Mussel-inspired DA was utilized to modify the GelMA molecules,which imparts good adhesive performance to the hydrogels.GO,interfacial enhancer,not only improves mechanical properties of the hydrogels,but also provides anchor sites for loading Ag NPs through numerous oxygencontaining functional groups on the surface.The experimental results show that the GelMA/Ag NPs/GO hydrogels have good biocompatibility,and exhibit a swelling rate of 202±16%,the lap shear strength of 147±17 kPa,and compressive modulus of 136±53 kPa,in the case of the Ag NPs/GO content of 2 mg/mL.Antibacterial activity of the hydrogels against both gram-negative and gram-positive bacteria is dependent on the Ag NPs/GO content derived from the release of Ag^(+).Furthermore,the GelMA/Ag NPs/GO hydrogels possess good adhesive ability,which is resistant to highly twisted state when stuck on the surface of pigskin.These results demonstrate promising potential of the GelMA-DA/Ag NPs/GO hydrogels as wound dressings for biomedical applications in clinical and emergent treatment.展开更多
Cement is widely used in engineering applications,but it has both the characteristics of high brittleness and poor bending resistance.In this paper,the effects of different amounts ofgraphene oxide on the flexural str...Cement is widely used in engineering applications,but it has both the characteristics of high brittleness and poor bending resistance.In this paper,the effects of different amounts ofgraphene oxide on the flexural strength and compressive strength of cement mortar were studied by doping a certain amount of graphene oxide with cement mortar,and the strengthening mechanism of graphene oxide on cement mortar was obtained through microstructure detection.It is found that graphene oxide has a significant enhancement effect on the macroscopic mechanical properties of cement mortar,and graphene oxide provides nano-nucleation sites and growth templates for cement mortar,accelerates the hydration process,reduces the voids between hydration products,greatly increases the compactness,and improves the macroscopic properties of cement-based materials.展开更多
Reduced graphene oxide(rGO)aerogels are emerging as very attractive scaffolds for high-performance electromagnetic wave absorption materials(EWAMs)due to their intrinsic conductive networks and intricate interior micr...Reduced graphene oxide(rGO)aerogels are emerging as very attractive scaffolds for high-performance electromagnetic wave absorption materials(EWAMs)due to their intrinsic conductive networks and intricate interior microstructure,as well as good compatibility with other electromagnetic(EM)components.Herein,we realized the decoration of rGO aerogel with Mo_(2)C nanoparticles by sequential hydrothermal assembly,freeze-drying,and high-temperature pyrolysis.Results show that Mo_(2)C nanoparticle loading can be easily controlled by the ammonium molybdate to glucose molar ratio.The hydrophobicity and thermal insulation of the rGO aerogel are effectively improved upon the introduction of Mo_(2)C nanoparticles,and more importantly,these nanoparticles regulate the EM properties of the rGO aerogel to a large extent.Although more Mo_(2)C nanoparticles may decrease the overall attenuation ability of the rGO aerogel,they bring much better impedance matching.At a molar ratio of 1:1,a desirable balance between attenuation ability and impedance matching is observed.In this context,the Mo_(2)C/r GO aerogel displays strong reflection loss and broad response bandwidth,even with a small applied thickness(1.7 mm)and low filler loading(9.0wt%).The positive effects of Mo_(2)C nanoparticles on multifunctional properties may render Mo_(2)C/r GO aerogels promising candidates for high-performance EWAMs under harsh conditions.展开更多
Graphene oxide(GO)as a new nano-enhancer in cement-based materials has gained wide attention.However,GO is easy to aggregate in alkaline cement mortar with poor dispersibility.This hinders its application in practical...Graphene oxide(GO)as a new nano-enhancer in cement-based materials has gained wide attention.However,GO is easy to aggregate in alkaline cement mortar with poor dispersibility.This hinders its application in practical infrastructure construction.In this work,GO-M18 polycarboxylate compound superplasticizer(GM)were obtained by compounding the M18 polycarboxylate superplasticizer with GO solution at different mass ratios.The dispersion of GM in alkaline solution was systematically studied.The phases and functional groups of GM were characterized by XRD and FTIR.The effects of GM on the cement mortar hydration and the formation of microstructure were investigated by measuring the heat of hydration,MIP,TG/DSC,and SEM.The results show that the long-chain structure of the M18 polycarboxylate superplasticizer can increase the interlayer spacing of GO and weaken the force between GO sheets.The modified GO can be uniformly dispersed in the cement slurry.GM can accelerate the early hydration process of cement,which can increase the content of Ca(OH)2 and decrease the grain size.It can optimize the pore size distribution of cement-based materials,increase the density of harmless and less harmful pores,thereby improving mechanical properties.Such methods can transform traditional cement-based materials into stronger,more durable composites,which prolong the life of cement-based materials and reduce the amount of cement used for later maintenance.This provides an idea for achieving sustainability goals in civil engineering.展开更多
Asymmetrically modified Janus graphene oxide(JGO)has attracted great attention due to its unique physical chemistry properties and wide applications.The modification degree of Janus nanosheets inevitably affects their...Asymmetrically modified Janus graphene oxide(JGO)has attracted great attention due to its unique physical chemistry properties and wide applications.The modification degree of Janus nanosheets inevitably affects their interfacial activity,which is essential for their performances in enhanced oil recovery(EOR).In this study,the interfacial properties of Janus graphene oxide(JGO)with various modification degrees at liquid-liquid and liquid-solid interfaces were systematically evaluated via the measurements of interfacial tension(IFT),dilatational modulus,contact angle,and EOR efficiency was further assessed by core flooding tests.It is found that JGO-5 with higher modification degree exhibits the greater ability to reduce IFT(15.16 mN/m)and dilatational modulus(26 mN/m).Furthermore,JGO can construct interfacial and climbing film with the assistance of hydrodynamic power to effectively detach the oil from the rock surface and greatly enhance oil recovery.Moderately modified JGO-2 can highly improve recovery of residual crude oil(11.53%),which is regarded as the promising EOR agent in practical application.The present study firstly focuses on the effects of modification degrees on the JGO interfacial properties and proposes diverse EOR mechanisms for JGO with different modification degrees.展开更多
Intercalation of insulating materials between epitaxial graphene and the metal substrates is highly demanded to restore the intrinsic properties of graphene,and thus essential for the graphene-based devices.Here we de...Intercalation of insulating materials between epitaxial graphene and the metal substrates is highly demanded to restore the intrinsic properties of graphene,and thus essential for the graphene-based devices.Here we demonstrate a successful solution for the intercalation of hafnium oxide into the interface between full-layer graphene and Ir(111)substrate.We first intercalate hafnium atoms beneath the epitaxial graphene.The intercalation of the hafnium atoms leads to the variation of the graphene moire superstructure periodicity,which is characterized by low-energy electron diffraction(LEED)and lowtemperature scanning tunneling microscopy(LT-STM).Subsequently,we introduce oxygen into the interface,resulting in oxidization of the intercalated hafnium.STM and Raman's characterizations reveal that the intercalated hafnium oxide layer could effectively decouple the graphene from the metallic substrate,while the graphene maintains its high quality.Our work suggests a high-k dielectric layer has been successfully intercalated between high-quality epitaxial graphene and metal substrate,providing a platform for applications of large-scale,high-quality graphene for electronic devices.展开更多
This paper investigates the effects of pH on stability and thermal properties of copper oxide(CuO),graphene oxide(GO),and their hybrid nanofluid(HNF)at different mixing ratios.Initially,sol-gel and Hummer’s method wa...This paper investigates the effects of pH on stability and thermal properties of copper oxide(CuO),graphene oxide(GO),and their hybrid nanofluid(HNF)at different mixing ratios.Initially,sol-gel and Hummer’s method was employed for the synthesis of CuO and GO nanoparticles(NPs),and they are characterized with various techniques.The effects of two different surfactants were analyzed on nanofluid’s(NF’s)stability at different pH values.The properties like thermal conductivity(TC)and viscosity(VST)of NFs were measured at different volume concentration(0.1 vol%to 1.0 vol%)and temperature range of 30-60℃,respectively.The TC and VST of GO/CuO(50:50)HNF are higher than that of GO/CuO(20:80).The figure of merit(FOM)is determined for the studied HNFs.The correlations were presented to calculate the TC as well as VST of HNFs.Two modern novel machine learning-based ensemble approaches were employed for predictive model development for TC and VST of considered HNFs.The comparison of prognostic models with Taylor’s diagram revealed that Bayesian optimized support vector machine(BoASVM)was superior to Bayesian optimized boosted regression trees(BoA-BRT)for both TC and VST models.展开更多
Water pollution regarding dyes and heavy metal ions is crucial facing the world.How to effectively separate these contaminants from water has been a key issue.Graphene oxide(GO)promises the greenwater world as a long-...Water pollution regarding dyes and heavy metal ions is crucial facing the world.How to effectively separate these contaminants from water has been a key issue.Graphene oxide(GO)promises the greenwater world as a long-lasting spotlight adsorbent material and therefore,harnessing GO has been the research hotspot for over a decade.The state of GO as well as its surface functional groups plays an important role in adsorption.And the way of preparation and structural modification matters to the performance of GO.In this review,the significance of the state of existence of stock GO and surface functional groups is explored in terms of preparation,structural modification,and adsorption.Besides,various adsorbates for GO adsorption are also involved,the discussion of which is rarely established elsewhere.展开更多
In this study,three-dimensional porous magnesium ferrite/titanium dioxide/reduced graphene oxide(Mg Fe_2O_(4)-GM/TiO_(2)/rGO(MGTG))was successfully synthesized via green and hydrothermal-supported co-precipitation met...In this study,three-dimensional porous magnesium ferrite/titanium dioxide/reduced graphene oxide(Mg Fe_2O_(4)-GM/TiO_(2)/rGO(MGTG))was successfully synthesized via green and hydrothermal-supported co-precipitation methods using the extract of Garcinia mangostana(G.mangostana)as a reducing agent.The characterization results indicate the successful formation of the nano/micro Mg Fe_(2)O_(4)(MFO)and TiO_(2) on the structure of the reduced graphene oxide(rGO),which can also act as efficient support,alleviating the agglomeration of the nano/micro MFO and TiO_(2).The synergic effects of the adsorption and photodegradation activity of the material were investigated according to the removal of crystal violet(CV)under ultraviolet light.The effects of catalyst dosage,CV concentration,and p H on the CV removal efficiency of the MGTG were also investigated.According to the results,the CV photodegradation of the MGTG-200 corresponded to the pseudo-first-order kinetic model.The reusability of the material after 10 cycles also showed a removal efficiency of 92%.This happened because the materials can easily be recollected using external magnets.In addition,according to the effects of different free radicals·O_(2)^(-),h^(+),and·OH on the photodegradation process,the photocatalysis mechanism of the MGTG was also thoroughly suggested.The antibacterial efficiency of the MGTG was also evaluated according to the inhibition of the Gram-positive bacteria strain Staphylococcus aureus(S.aureus).Concurrently,the antibacterial mechanism of the fabricated material was also proposed.These results confirm that the prepared material can be potentially employed in a wide range of applications,including wastewater treatment and antibacterial activity.展开更多
The adsorption dynamics of double-stranded DNA(dsDNA)molecules on a graphene oxide(GO)surface are important for applications of DNA/GO functional structures in biosensors,biomedicine and materials science.In this work...The adsorption dynamics of double-stranded DNA(dsDNA)molecules on a graphene oxide(GO)surface are important for applications of DNA/GO functional structures in biosensors,biomedicine and materials science.In this work,molecular dynamics simulations were used to examine the adsorption of different length dsDNA molecules(from 4 bp to24 bp)on the GO surface.The dsDNA molecules could be adsorbed on the GO surface through the terminal bases and stand on the GO surface.For short dsDNA(4 bp)molecules,the double-helix structure was partially or totally broken and the adsorption dynamics was affected by the structural fluctuation of short dsDNA and the distribution of the oxidized groups on the GO surface.For long dsDNA molecules(from 8 bp to 24 bp)adsorption is stable.By nonlinear fitting of the contact angle between the axis of the dsDNA molecule and the GO surface,we found that a dsDNA molecule adsorbed on a GO surface has the chance of orienting parallel to the GO surface if the length of the dsDNA molecule is longer than 54 bp.We attributed this behavior to the flexibility of dsDNA molecules.With increasing length,the flexibility of dsDNA molecules also increases,and this increasing flexibility gives an adsorbed dsDNA molecule more chance of reaching the GO surface with the free terminal.This work provides a whole picture of adsorption of dsDNA molecules on the GO surface and should be of benefit for the design of DNA/GO based biosensors.展开更多
The doping of functionalized graphene oxide(GO)in the membranes becomes a promising method for improving the performance of high-temperature proton exchange membrane fuel cells(HT-PEMFC).Phosphonated graphene oxide(PG...The doping of functionalized graphene oxide(GO)in the membranes becomes a promising method for improving the performance of high-temperature proton exchange membrane fuel cells(HT-PEMFC).Phosphonated graphene oxide(PGO)with a P/O ratio of 8.5%was quickly synthesised by one-step electrochemical exfoliation based on a three-dimensiaonal(3D)printed reactor and natural graphite flakes.Compared with the GO prepared by the two-step electrochemical exfoliation method,the PGO synthesized by the one-step electrochemical exfoliation can better improve the performance of the membrane-electrode-assembly(MEA)based on the polybenzimidazole(PBI)membrane in the HTPEMFC.The doping of 1.5 wt%GO synthesised by electrochemical exfoliation with the 2-step method or reactor method in PBI increased the peak power density by 17.4%or 35.4%compared to MEA based on pure PBI membrane at 150℃,respectively.In addition,the doping of PGO in PBI improves its durability under accelerated stress test(AST).展开更多
The main bottleneck against industrial utilization of sodium ion batteries(SIBs)is the lack of high-capacity electrodes to rival those of the benchmark lithium ion batteries(LIBs).Here in this work,we have developed a...The main bottleneck against industrial utilization of sodium ion batteries(SIBs)is the lack of high-capacity electrodes to rival those of the benchmark lithium ion batteries(LIBs).Here in this work,we have developed an economical method for in situ fabrication of nanocomposites made of crystalline few-layer graphene sheets loaded with ultrafine SnO_(2)nanocrystals,using short exposure of microwave to xerogel of graphene oxide(GO)and tin tetrachloride containing minute catalyzing dispersoids of chemically reduced GO(RGO).The resultant nanocomposites(SnO_(2)@MWG)enabled significantly quickened redox processes as SIB anode,which led to remarkable full anode-specific capacity reaching 538 mAh g^(−1)at 0.05 A g^(−1)(about 1.45 times of the theoretical capacity of graphite for the LIB),in addition to outstanding rate performance over prolonged charge–discharge cycling.Anodes based on the optimized SnO_(2)@MWG delivered stable performance over 2000 cycles even at a high current density of 5 A g^(−1),and capacity retention of over 70.4%was maintained at a high areal loading of 3.4 mg cm^(−2),highly desirable for high energy density SIBs to rival the current benchmark LIBs.展开更多
Thanks to their remarkable mechanical, electrical, thermal, and barrier properties, graphene-based nanocomposites have been a hot area of research in the past decade. Because of their simple top-down synthesis, graphe...Thanks to their remarkable mechanical, electrical, thermal, and barrier properties, graphene-based nanocomposites have been a hot area of research in the past decade. Because of their simple top-down synthesis, graphene oxide (GO) and reduced graphene oxide (rGO) have opened new possibilities for gas barrier, membrane separation, and stimuli-response characteristics in nanocomposites. Herein, we review the synthesis techniques most commonly used to produce these graphene derivatives, discuss how synthesis affects their key material properties, and highlight some examples of nanocomposites with unique and impressive properties. We specifically highlight their performances in separation applications, stimuli-responsive materials, anti-corrosion coatings, and energy storage. Finally, we discuss the outlook and remaining challenges in the field of practical industrial-scale production and use of graphene-derivative-based polymer nanocomposites.展开更多
Polarization and conductance losses are the fundamental dielectric attenuation mechanisms for graphene-based absorbers, but it is not fully understood in revealing the loss mechanism of affect graphene itself. For the...Polarization and conductance losses are the fundamental dielectric attenuation mechanisms for graphene-based absorbers, but it is not fully understood in revealing the loss mechanism of affect graphene itself. For the first time, the reduced graphene oxide(RGO) based absorbers are developed with regulatory absorption properties and the absorption mechanism of RGO is mainly originated from the carrier injection behavior of trace metal Fe nanosheets on graphene. Accordingly, the minimum reflection loss(RLmin) of Fe/RGO-2composite reaches-53.38 dB(2.45 mm), and the effective absorption bandwidth achieves 7.52 GHz(2.62 mm) with lower filling loading of 2 wt%. Using off-axis electron hologram testing combined with simulation calculation and carrier transport property experiments, we demonstrate here the carrier injection behavior from Fe to graphene at the interface and the induced charge accumulation and rearrangement, resulting in the increased interfacial and dipole polarization and the conductance loss. This work has confirmed that regulating the dielectric property of graphene itself by adding trace metals can not only ensure good impedance matching, but also fully exploit the dielectric loss ability of graphene at low filler content,which opens up an efficient way for designing lightweight absorbers and may be extended to other types materials.展开更多
Natural intercalation of the graphite oxide, obtained as a product of Hummer's method, via ultra-sonication of water dispersed graphite oxide has been carried out to obtain graphene oxide(GO) and thermally reduced ...Natural intercalation of the graphite oxide, obtained as a product of Hummer's method, via ultra-sonication of water dispersed graphite oxide has been carried out to obtain graphene oxide(GO) and thermally reduced graphene oxide(RGO).Here we report the effect of metallic nitrate on the oxidation properties of graphite and then formation of metallic oxide(MO) composites with GO and RGO for the first time. We observed a change in the efficiency of the oxidation process as we replaced the conventionally used sodium nitrate with that of nickel nitrate Ni(NO_3)_2, cadmium nitrate Cd(NO_3)_2,and zinc nitrate Zn(NO_3)_2. The structural properties were investigated by x-ray diffraction and observed the successful formation of composite of MO–GO and MO–RGO(M = Zn, Cd, Ni). We sought to study the effect on the oxidation process through optical characterization via UV-Vis spectroscopy and Fourier Transform Infrared(FTIR) spectroscopy.Moreover, Thermo Gravimetric Analysis(TGA) was carried out to confirm 〉 90% weight loss in each process thus proving the reliability of the oxidation cycles. We have found that the nature of the oxidation process of graphite powder and its optical and electrochemical characteristics can be tuned by replacing the sodium nitrate(NaNO_3) by other metallic nitrates as Cd(NO_3)_2, Ni(NO_3)_2, and Zn(NO_3)_2. On the basis of obtained results, the synthesized GO and RGO may be expected as a promising material in antibacterial activity and in electrodes fabrication for energy devices such as solar cell, fuel cell,and super capacitors.展开更多
Micro arc oxidation(MAO) coatings doped with graphene oxide(GO) were prepared on pure titanium by adding GO and sodium dodecyl benzene sulfonate(SDBS) into a sodium silicate solution. The as-deposited coatings were co...Micro arc oxidation(MAO) coatings doped with graphene oxide(GO) were prepared on pure titanium by adding GO and sodium dodecyl benzene sulfonate(SDBS) into a sodium silicate solution. The as-deposited coatings were comparatively analyzed by scanning electron microscopy(SEM), energydispersive X-ray spectroscopy(EDS) and X-ray diffraction(XRD). The binding forces of the MAO, MAO+GO and MAO+GO+SDBS three coatings were measured by a scratch tester. The mechanical property of the three coatings was analyzed using the nano-indentation technique. The corrosion resistance of the coatings was tested by the electrochemical system in 3.5% NaCl solution. The photocatalytic activity of the prepared samples was evaluated by determining the degradation of methylene blue(MB) solution. The results showed that compared to the MAO coating, the morphologies and phase compositions of MAO+GO and MAO+GO+SDBS composite coatings were significantly different. These two composite coatings all had superior photocatalytic activity. Especially, the MAO+GO composite coating still had enhanced binding force and excellent corrosion resistance. Furthermore, the relationship between the microstructure and the properties of these three MAO coatings was analyzed.展开更多
This study investigates the effect of graphene oxide(GO)on the mechanical and corrosion behavior,antibacterial performance,and cell response of Mg–Zn–Mn(MZM)nanocomposite.MZM/GO nanocomposites with different amounts...This study investigates the effect of graphene oxide(GO)on the mechanical and corrosion behavior,antibacterial performance,and cell response of Mg–Zn–Mn(MZM)nanocomposite.MZM/GO nanocomposites with different amounts of GO(i.e.,0.5 wt%,1.0 wt%,and1.5 wt%)were fabricated by the semi-powder metallurgy method.The influence of GO on the MZM nanocomposite was analyzed through the hardness,compressive,corrosion,antibacterial,and cytotoxicity tests.The experimental results showed that,with the increase in the amount of GO(0.5 wt%and 1.5 wt%),the hardness value,compressive strength,and antibacterial performance of the MZM nanocomposite increased,whereas the cell viability and osteogenesis level decreased after the addition of 1.5 wt%GO.Moreover,the electrochemical examination results showed that the corrosion behavior of the MZM alloy was significantly enhanced after encapsulation in 0.5 wt%GO.In summary,MZM nanocomposites reinforced with GO can be used for implant applications because of their antibacterial performance and mechanical property.展开更多
The effect of graphene oxide(GO)and reduced graphene oxide(RGO)nanosheets on the microstructure and mechanical properties of welded joints of mild steel was evaluated by flux-cored arc welding.GO was synthesized by th...The effect of graphene oxide(GO)and reduced graphene oxide(RGO)nanosheets on the microstructure and mechanical properties of welded joints of mild steel was evaluated by flux-cored arc welding.GO was synthesized by the Hummer’s method and was reduced under hydrothermal conditions at a pressure of 1.1 MPa at 180°C for 12 h.1,3,and 10 mg/mL paste fillers were used in GO and RGO,and applied to the weld notch.The results clearly showed that by increasing the concentration of RGO up to 10 mg/mL,the tensile strength and hardness of the weld metal were improved by approximately 20.5%and 38.4%,respectively,because the coarse grains were changed into fine domains.The domain of the nanosheets cluster was 19.85×10^?9 m.Specifically,the RGO nanosheets contributed to modifying the mechanical properties of the welded steel,likely due to dislocation pinning.展开更多
Due to its great strength, hardness, and chemical resistance, epoxy adhesives are becoming more and more used. They continue to have drawbacks, nevertheless, such as poor thermal stability, and poor electrical conduct...Due to its great strength, hardness, and chemical resistance, epoxy adhesives are becoming more and more used. They continue to have drawbacks, nevertheless, such as poor thermal stability, and poor electrical conductivity. Two-dimensional graphene is a wonderful substance with exceptional qualities including high strength, high electrical conductivity, and large surface area. Because of these characteristics, graphene has been thoroughly researched for its prospective uses in a variety of industries, including electronics, energy storage, and biomedical engineering. The use of graphene as an additive in epoxy adhesives to enhance the characteristics of such materials is one of its promising uses. This paper reviewed the latest findings about graphene’s effects on epoxy adhesives. The various methods to produce graphene-epoxy composites and their improvements are discussed. This research additionally discusses the challenges associated with the production and processing of graphene-epoxy composites, as well as the mechanisms behind the improvements in mechanical, electrical, and thermal characteristics. The final section of this review discusses the challenges and prospective uses of graphene in epoxy adhesives in the future.展开更多
A simple and reliable strategy was proposed to engineer the glutathione grafted graphene oxide/ZnO nanocomposite(glutathione-GO/ZnO)as electrode material for the high-performance piroxicam sensor.The prepared glutathi...A simple and reliable strategy was proposed to engineer the glutathione grafted graphene oxide/ZnO nanocomposite(glutathione-GO/ZnO)as electrode material for the high-performance piroxicam sensor.The prepared glutathione-GO/ZnO nanocomposite was well characterized by X-ray diffraction(XRD),Fourier transform infrared spectrum(FTIR),X-ray photoelectron spectroscopy(XPS),field emission scanning electron microscopy(FE-SEM),cyclic voltammetry(CV),electrochemical impedance spectroscopy(EIS)and differential pulse voltammetry(DPV).The novel nanocomposite modified electrode showed the highest electrocatalytic activity towards piroxicam(oxidation potential is 0.52 V).Under controlled experimental parameters,the proposed sensor exhibited good linear responses to piroxicam concentrations ranging from 0.1 to 500 μM.The detection limit and sensitivity were calculated as 1.8 μM and 0.2 μA/μM·cm^(2),respectively.Moreover,it offered excellent selectivity,reproducibility,and long-term stability and can effectively ignore the interfering candidates commonly existing in the pharmaceutical tablets and human fluids even at a higher concentration.Finally,the reported sensor was successfully employed to the direct determination of piroxicam in practical samples.展开更多
基金Funded by the National Key Research and Development(R&D) Program of China(No.2018YFB1105702)。
文摘A novel strategy was developed to prepare the methacrylic gelatin-dopamine(GelMA-DA)/Ag nanoparticles(NPs)/graphene oxide(GO) composite hydrogels with good biocompatibility,mechanical properties,and antibacterial activity.Mussel-inspired DA was utilized to modify the GelMA molecules,which imparts good adhesive performance to the hydrogels.GO,interfacial enhancer,not only improves mechanical properties of the hydrogels,but also provides anchor sites for loading Ag NPs through numerous oxygencontaining functional groups on the surface.The experimental results show that the GelMA/Ag NPs/GO hydrogels have good biocompatibility,and exhibit a swelling rate of 202±16%,the lap shear strength of 147±17 kPa,and compressive modulus of 136±53 kPa,in the case of the Ag NPs/GO content of 2 mg/mL.Antibacterial activity of the hydrogels against both gram-negative and gram-positive bacteria is dependent on the Ag NPs/GO content derived from the release of Ag^(+).Furthermore,the GelMA/Ag NPs/GO hydrogels possess good adhesive ability,which is resistant to highly twisted state when stuck on the surface of pigskin.These results demonstrate promising potential of the GelMA-DA/Ag NPs/GO hydrogels as wound dressings for biomedical applications in clinical and emergent treatment.
基金This work were supported by Natural Science Foundation of Zhejiang Province(LQ23E080003)a Doctoral program of Zhejiang University of science and technology(F701104L08)The Special Fund Project of Zhejiang University of Science and Technology's Basic Scientific Research Business Expenses in 2023(2023QN016).
文摘Cement is widely used in engineering applications,but it has both the characteristics of high brittleness and poor bending resistance.In this paper,the effects of different amounts ofgraphene oxide on the flexural strength and compressive strength of cement mortar were studied by doping a certain amount of graphene oxide with cement mortar,and the strengthening mechanism of graphene oxide on cement mortar was obtained through microstructure detection.It is found that graphene oxide has a significant enhancement effect on the macroscopic mechanical properties of cement mortar,and graphene oxide provides nano-nucleation sites and growth templates for cement mortar,accelerates the hydration process,reduces the voids between hydration products,greatly increases the compactness,and improves the macroscopic properties of cement-based materials.
基金supported by the China Postdoctoral Science Foundation(No.2021MD703944)the Fund of Science and Technology on Near-Surface Detection Laboratory(No.6142414211808)+1 种基金the Director Fund of State Key Laboratory of Pulsed Power Laser Technology(No.SKL2021ZR06)the National Natural Science Foundation of China(No.21776053)。
文摘Reduced graphene oxide(rGO)aerogels are emerging as very attractive scaffolds for high-performance electromagnetic wave absorption materials(EWAMs)due to their intrinsic conductive networks and intricate interior microstructure,as well as good compatibility with other electromagnetic(EM)components.Herein,we realized the decoration of rGO aerogel with Mo_(2)C nanoparticles by sequential hydrothermal assembly,freeze-drying,and high-temperature pyrolysis.Results show that Mo_(2)C nanoparticle loading can be easily controlled by the ammonium molybdate to glucose molar ratio.The hydrophobicity and thermal insulation of the rGO aerogel are effectively improved upon the introduction of Mo_(2)C nanoparticles,and more importantly,these nanoparticles regulate the EM properties of the rGO aerogel to a large extent.Although more Mo_(2)C nanoparticles may decrease the overall attenuation ability of the rGO aerogel,they bring much better impedance matching.At a molar ratio of 1:1,a desirable balance between attenuation ability and impedance matching is observed.In this context,the Mo_(2)C/r GO aerogel displays strong reflection loss and broad response bandwidth,even with a small applied thickness(1.7 mm)and low filler loading(9.0wt%).The positive effects of Mo_(2)C nanoparticles on multifunctional properties may render Mo_(2)C/r GO aerogels promising candidates for high-performance EWAMs under harsh conditions.
基金funded by the National Natural Science Foundation of China(No.51872137)and Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)。
文摘Graphene oxide(GO)as a new nano-enhancer in cement-based materials has gained wide attention.However,GO is easy to aggregate in alkaline cement mortar with poor dispersibility.This hinders its application in practical infrastructure construction.In this work,GO-M18 polycarboxylate compound superplasticizer(GM)were obtained by compounding the M18 polycarboxylate superplasticizer with GO solution at different mass ratios.The dispersion of GM in alkaline solution was systematically studied.The phases and functional groups of GM were characterized by XRD and FTIR.The effects of GM on the cement mortar hydration and the formation of microstructure were investigated by measuring the heat of hydration,MIP,TG/DSC,and SEM.The results show that the long-chain structure of the M18 polycarboxylate superplasticizer can increase the interlayer spacing of GO and weaken the force between GO sheets.The modified GO can be uniformly dispersed in the cement slurry.GM can accelerate the early hydration process of cement,which can increase the content of Ca(OH)2 and decrease the grain size.It can optimize the pore size distribution of cement-based materials,increase the density of harmless and less harmful pores,thereby improving mechanical properties.Such methods can transform traditional cement-based materials into stronger,more durable composites,which prolong the life of cement-based materials and reduce the amount of cement used for later maintenance.This provides an idea for achieving sustainability goals in civil engineering.
基金grateful for funding from the National Natural Science Foundation of China(Grant No.52174053,52130401 and 51974344)Natural Science Foundation of Shandong Provincial(ZR2019MEE077).
文摘Asymmetrically modified Janus graphene oxide(JGO)has attracted great attention due to its unique physical chemistry properties and wide applications.The modification degree of Janus nanosheets inevitably affects their interfacial activity,which is essential for their performances in enhanced oil recovery(EOR).In this study,the interfacial properties of Janus graphene oxide(JGO)with various modification degrees at liquid-liquid and liquid-solid interfaces were systematically evaluated via the measurements of interfacial tension(IFT),dilatational modulus,contact angle,and EOR efficiency was further assessed by core flooding tests.It is found that JGO-5 with higher modification degree exhibits the greater ability to reduce IFT(15.16 mN/m)and dilatational modulus(26 mN/m).Furthermore,JGO can construct interfacial and climbing film with the assistance of hydrodynamic power to effectively detach the oil from the rock surface and greatly enhance oil recovery.Moderately modified JGO-2 can highly improve recovery of residual crude oil(11.53%),which is regarded as the promising EOR agent in practical application.The present study firstly focuses on the effects of modification degrees on the JGO interfacial properties and proposes diverse EOR mechanisms for JGO with different modification degrees.
基金the Ministry of Science and Technology of China(Grant Nos.2018YFA0305800 and2019YFA0308500)the National Natural Science Foundation of China(Grant No.61925111)+2 种基金the Chinese Academy of Sciences(Grant Nos.XDB28000000 and YSBR-003)the Fundamental Research Funds for the Central Universitiesthe CAS Key Laboratory of Vacuum Physics。
文摘Intercalation of insulating materials between epitaxial graphene and the metal substrates is highly demanded to restore the intrinsic properties of graphene,and thus essential for the graphene-based devices.Here we demonstrate a successful solution for the intercalation of hafnium oxide into the interface between full-layer graphene and Ir(111)substrate.We first intercalate hafnium atoms beneath the epitaxial graphene.The intercalation of the hafnium atoms leads to the variation of the graphene moire superstructure periodicity,which is characterized by low-energy electron diffraction(LEED)and lowtemperature scanning tunneling microscopy(LT-STM).Subsequently,we introduce oxygen into the interface,resulting in oxidization of the intercalated hafnium.STM and Raman's characterizations reveal that the intercalated hafnium oxide layer could effectively decouple the graphene from the metallic substrate,while the graphene maintains its high quality.Our work suggests a high-k dielectric layer has been successfully intercalated between high-quality epitaxial graphene and metal substrate,providing a platform for applications of large-scale,high-quality graphene for electronic devices.
文摘This paper investigates the effects of pH on stability and thermal properties of copper oxide(CuO),graphene oxide(GO),and their hybrid nanofluid(HNF)at different mixing ratios.Initially,sol-gel and Hummer’s method was employed for the synthesis of CuO and GO nanoparticles(NPs),and they are characterized with various techniques.The effects of two different surfactants were analyzed on nanofluid’s(NF’s)stability at different pH values.The properties like thermal conductivity(TC)and viscosity(VST)of NFs were measured at different volume concentration(0.1 vol%to 1.0 vol%)and temperature range of 30-60℃,respectively.The TC and VST of GO/CuO(50:50)HNF are higher than that of GO/CuO(20:80).The figure of merit(FOM)is determined for the studied HNFs.The correlations were presented to calculate the TC as well as VST of HNFs.Two modern novel machine learning-based ensemble approaches were employed for predictive model development for TC and VST of considered HNFs.The comparison of prognostic models with Taylor’s diagram revealed that Bayesian optimized support vector machine(BoASVM)was superior to Bayesian optimized boosted regression trees(BoA-BRT)for both TC and VST models.
基金supported by the National Natural Science Foundation of China(51902007)。
文摘Water pollution regarding dyes and heavy metal ions is crucial facing the world.How to effectively separate these contaminants from water has been a key issue.Graphene oxide(GO)promises the greenwater world as a long-lasting spotlight adsorbent material and therefore,harnessing GO has been the research hotspot for over a decade.The state of GO as well as its surface functional groups plays an important role in adsorption.And the way of preparation and structural modification matters to the performance of GO.In this review,the significance of the state of existence of stock GO and surface functional groups is explored in terms of preparation,structural modification,and adsorption.Besides,various adsorbates for GO adsorption are also involved,the discussion of which is rarely established elsewhere.
基金Ho Chi Minh City University of Technology (HCMUT),VNU-HCM for supporting this study。
文摘In this study,three-dimensional porous magnesium ferrite/titanium dioxide/reduced graphene oxide(Mg Fe_2O_(4)-GM/TiO_(2)/rGO(MGTG))was successfully synthesized via green and hydrothermal-supported co-precipitation methods using the extract of Garcinia mangostana(G.mangostana)as a reducing agent.The characterization results indicate the successful formation of the nano/micro Mg Fe_(2)O_(4)(MFO)and TiO_(2) on the structure of the reduced graphene oxide(rGO),which can also act as efficient support,alleviating the agglomeration of the nano/micro MFO and TiO_(2).The synergic effects of the adsorption and photodegradation activity of the material were investigated according to the removal of crystal violet(CV)under ultraviolet light.The effects of catalyst dosage,CV concentration,and p H on the CV removal efficiency of the MGTG were also investigated.According to the results,the CV photodegradation of the MGTG-200 corresponded to the pseudo-first-order kinetic model.The reusability of the material after 10 cycles also showed a removal efficiency of 92%.This happened because the materials can easily be recollected using external magnets.In addition,according to the effects of different free radicals·O_(2)^(-),h^(+),and·OH on the photodegradation process,the photocatalysis mechanism of the MGTG was also thoroughly suggested.The antibacterial efficiency of the MGTG was also evaluated according to the inhibition of the Gram-positive bacteria strain Staphylococcus aureus(S.aureus).Concurrently,the antibacterial mechanism of the fabricated material was also proposed.These results confirm that the prepared material can be potentially employed in a wide range of applications,including wastewater treatment and antibacterial activity.
基金Project supported by the National Natural Science Foundation of China (Grant No.11974366)the Fundamental Research Funds for the Central Universities+2 种基金Chinathe Supercomputer Center of the Chinese Academy of Sciencesthe Shanghai Supercomputer Center of China。
文摘The adsorption dynamics of double-stranded DNA(dsDNA)molecules on a graphene oxide(GO)surface are important for applications of DNA/GO functional structures in biosensors,biomedicine and materials science.In this work,molecular dynamics simulations were used to examine the adsorption of different length dsDNA molecules(from 4 bp to24 bp)on the GO surface.The dsDNA molecules could be adsorbed on the GO surface through the terminal bases and stand on the GO surface.For short dsDNA(4 bp)molecules,the double-helix structure was partially or totally broken and the adsorption dynamics was affected by the structural fluctuation of short dsDNA and the distribution of the oxidized groups on the GO surface.For long dsDNA molecules(from 8 bp to 24 bp)adsorption is stable.By nonlinear fitting of the contact angle between the axis of the dsDNA molecule and the GO surface,we found that a dsDNA molecule adsorbed on a GO surface has the chance of orienting parallel to the GO surface if the length of the dsDNA molecule is longer than 54 bp.We attributed this behavior to the flexibility of dsDNA molecules.With increasing length,the flexibility of dsDNA molecules also increases,and this increasing flexibility gives an adsorbed dsDNA molecule more chance of reaching the GO surface with the free terminal.This work provides a whole picture of adsorption of dsDNA molecules on the GO surface and should be of benefit for the design of DNA/GO based biosensors.
基金financially supported by the UK Research Council EPSRC EP/009050/1。
文摘The doping of functionalized graphene oxide(GO)in the membranes becomes a promising method for improving the performance of high-temperature proton exchange membrane fuel cells(HT-PEMFC).Phosphonated graphene oxide(PGO)with a P/O ratio of 8.5%was quickly synthesised by one-step electrochemical exfoliation based on a three-dimensiaonal(3D)printed reactor and natural graphite flakes.Compared with the GO prepared by the two-step electrochemical exfoliation method,the PGO synthesized by the one-step electrochemical exfoliation can better improve the performance of the membrane-electrode-assembly(MEA)based on the polybenzimidazole(PBI)membrane in the HTPEMFC.The doping of 1.5 wt%GO synthesised by electrochemical exfoliation with the 2-step method or reactor method in PBI increased the peak power density by 17.4%or 35.4%compared to MEA based on pure PBI membrane at 150℃,respectively.In addition,the doping of PGO in PBI improves its durability under accelerated stress test(AST).
基金funded by the Zhengzhou Materials Genome Institute,the National Talents Program of China,and Key Innovation Projects of the Zhengzhou Municipal City of China.
文摘The main bottleneck against industrial utilization of sodium ion batteries(SIBs)is the lack of high-capacity electrodes to rival those of the benchmark lithium ion batteries(LIBs).Here in this work,we have developed an economical method for in situ fabrication of nanocomposites made of crystalline few-layer graphene sheets loaded with ultrafine SnO_(2)nanocrystals,using short exposure of microwave to xerogel of graphene oxide(GO)and tin tetrachloride containing minute catalyzing dispersoids of chemically reduced GO(RGO).The resultant nanocomposites(SnO_(2)@MWG)enabled significantly quickened redox processes as SIB anode,which led to remarkable full anode-specific capacity reaching 538 mAh g^(−1)at 0.05 A g^(−1)(about 1.45 times of the theoretical capacity of graphite for the LIB),in addition to outstanding rate performance over prolonged charge–discharge cycling.Anodes based on the optimized SnO_(2)@MWG delivered stable performance over 2000 cycles even at a high current density of 5 A g^(−1),and capacity retention of over 70.4%was maintained at a high areal loading of 3.4 mg cm^(−2),highly desirable for high energy density SIBs to rival the current benchmark LIBs.
基金sponsored by the National Science Foundation (NSF, CMMI-1562907)the GAANN Fellowship for financial support (No. P200A150330)the Navy STEM Fellowship and the GAANN Fellowship for financial support
文摘Thanks to their remarkable mechanical, electrical, thermal, and barrier properties, graphene-based nanocomposites have been a hot area of research in the past decade. Because of their simple top-down synthesis, graphene oxide (GO) and reduced graphene oxide (rGO) have opened new possibilities for gas barrier, membrane separation, and stimuli-response characteristics in nanocomposites. Herein, we review the synthesis techniques most commonly used to produce these graphene derivatives, discuss how synthesis affects their key material properties, and highlight some examples of nanocomposites with unique and impressive properties. We specifically highlight their performances in separation applications, stimuli-responsive materials, anti-corrosion coatings, and energy storage. Finally, we discuss the outlook and remaining challenges in the field of practical industrial-scale production and use of graphene-derivative-based polymer nanocomposites.
基金supported by National Natural Science Foundation of China (NSFC 52372041, 52302087, 51772060, 51672059 and 51621091)Heilongjiang Touyan Team Program+1 种基金the Fundamental Research Funds for the Central Universities (Grant No. HIT.OCEF.2021003)the Shanghai Aerospace Science and Technology Innovation Fund (SAST2022-60)。
文摘Polarization and conductance losses are the fundamental dielectric attenuation mechanisms for graphene-based absorbers, but it is not fully understood in revealing the loss mechanism of affect graphene itself. For the first time, the reduced graphene oxide(RGO) based absorbers are developed with regulatory absorption properties and the absorption mechanism of RGO is mainly originated from the carrier injection behavior of trace metal Fe nanosheets on graphene. Accordingly, the minimum reflection loss(RLmin) of Fe/RGO-2composite reaches-53.38 dB(2.45 mm), and the effective absorption bandwidth achieves 7.52 GHz(2.62 mm) with lower filling loading of 2 wt%. Using off-axis electron hologram testing combined with simulation calculation and carrier transport property experiments, we demonstrate here the carrier injection behavior from Fe to graphene at the interface and the induced charge accumulation and rearrangement, resulting in the increased interfacial and dipole polarization and the conductance loss. This work has confirmed that regulating the dielectric property of graphene itself by adding trace metals can not only ensure good impedance matching, but also fully exploit the dielectric loss ability of graphene at low filler content,which opens up an efficient way for designing lightweight absorbers and may be extended to other types materials.
文摘Natural intercalation of the graphite oxide, obtained as a product of Hummer's method, via ultra-sonication of water dispersed graphite oxide has been carried out to obtain graphene oxide(GO) and thermally reduced graphene oxide(RGO).Here we report the effect of metallic nitrate on the oxidation properties of graphite and then formation of metallic oxide(MO) composites with GO and RGO for the first time. We observed a change in the efficiency of the oxidation process as we replaced the conventionally used sodium nitrate with that of nickel nitrate Ni(NO_3)_2, cadmium nitrate Cd(NO_3)_2,and zinc nitrate Zn(NO_3)_2. The structural properties were investigated by x-ray diffraction and observed the successful formation of composite of MO–GO and MO–RGO(M = Zn, Cd, Ni). We sought to study the effect on the oxidation process through optical characterization via UV-Vis spectroscopy and Fourier Transform Infrared(FTIR) spectroscopy.Moreover, Thermo Gravimetric Analysis(TGA) was carried out to confirm 〉 90% weight loss in each process thus proving the reliability of the oxidation cycles. We have found that the nature of the oxidation process of graphite powder and its optical and electrochemical characteristics can be tuned by replacing the sodium nitrate(NaNO_3) by other metallic nitrates as Cd(NO_3)_2, Ni(NO_3)_2, and Zn(NO_3)_2. On the basis of obtained results, the synthesized GO and RGO may be expected as a promising material in antibacterial activity and in electrodes fabrication for energy devices such as solar cell, fuel cell,and super capacitors.
基金Funded by the National Natural Science Foundation of China(No.51571114)the Key Research and Development Plan of Shaanxi Province-Industrial Project(No.2018GY-127)
文摘Micro arc oxidation(MAO) coatings doped with graphene oxide(GO) were prepared on pure titanium by adding GO and sodium dodecyl benzene sulfonate(SDBS) into a sodium silicate solution. The as-deposited coatings were comparatively analyzed by scanning electron microscopy(SEM), energydispersive X-ray spectroscopy(EDS) and X-ray diffraction(XRD). The binding forces of the MAO, MAO+GO and MAO+GO+SDBS three coatings were measured by a scratch tester. The mechanical property of the three coatings was analyzed using the nano-indentation technique. The corrosion resistance of the coatings was tested by the electrochemical system in 3.5% NaCl solution. The photocatalytic activity of the prepared samples was evaluated by determining the degradation of methylene blue(MB) solution. The results showed that compared to the MAO coating, the morphologies and phase compositions of MAO+GO and MAO+GO+SDBS composite coatings were significantly different. These two composite coatings all had superior photocatalytic activity. Especially, the MAO+GO composite coating still had enhanced binding force and excellent corrosion resistance. Furthermore, the relationship between the microstructure and the properties of these three MAO coatings was analyzed.
文摘This study investigates the effect of graphene oxide(GO)on the mechanical and corrosion behavior,antibacterial performance,and cell response of Mg–Zn–Mn(MZM)nanocomposite.MZM/GO nanocomposites with different amounts of GO(i.e.,0.5 wt%,1.0 wt%,and1.5 wt%)were fabricated by the semi-powder metallurgy method.The influence of GO on the MZM nanocomposite was analyzed through the hardness,compressive,corrosion,antibacterial,and cytotoxicity tests.The experimental results showed that,with the increase in the amount of GO(0.5 wt%and 1.5 wt%),the hardness value,compressive strength,and antibacterial performance of the MZM nanocomposite increased,whereas the cell viability and osteogenesis level decreased after the addition of 1.5 wt%GO.Moreover,the electrochemical examination results showed that the corrosion behavior of the MZM alloy was significantly enhanced after encapsulation in 0.5 wt%GO.In summary,MZM nanocomposites reinforced with GO can be used for implant applications because of their antibacterial performance and mechanical property.
基金the Sustainable Nano Surfaces of the East(Payanano.com)Company in Islamic Republic of Iran.
文摘The effect of graphene oxide(GO)and reduced graphene oxide(RGO)nanosheets on the microstructure and mechanical properties of welded joints of mild steel was evaluated by flux-cored arc welding.GO was synthesized by the Hummer’s method and was reduced under hydrothermal conditions at a pressure of 1.1 MPa at 180°C for 12 h.1,3,and 10 mg/mL paste fillers were used in GO and RGO,and applied to the weld notch.The results clearly showed that by increasing the concentration of RGO up to 10 mg/mL,the tensile strength and hardness of the weld metal were improved by approximately 20.5%and 38.4%,respectively,because the coarse grains were changed into fine domains.The domain of the nanosheets cluster was 19.85×10^?9 m.Specifically,the RGO nanosheets contributed to modifying the mechanical properties of the welded steel,likely due to dislocation pinning.
文摘Due to its great strength, hardness, and chemical resistance, epoxy adhesives are becoming more and more used. They continue to have drawbacks, nevertheless, such as poor thermal stability, and poor electrical conductivity. Two-dimensional graphene is a wonderful substance with exceptional qualities including high strength, high electrical conductivity, and large surface area. Because of these characteristics, graphene has been thoroughly researched for its prospective uses in a variety of industries, including electronics, energy storage, and biomedical engineering. The use of graphene as an additive in epoxy adhesives to enhance the characteristics of such materials is one of its promising uses. This paper reviewed the latest findings about graphene’s effects on epoxy adhesives. The various methods to produce graphene-epoxy composites and their improvements are discussed. This research additionally discusses the challenges associated with the production and processing of graphene-epoxy composites, as well as the mechanisms behind the improvements in mechanical, electrical, and thermal characteristics. The final section of this review discusses the challenges and prospective uses of graphene in epoxy adhesives in the future.
基金supported by SERB(Science and Engineering Research Board),New Delhi,India[File.No:EMR/2014/000020].
文摘A simple and reliable strategy was proposed to engineer the glutathione grafted graphene oxide/ZnO nanocomposite(glutathione-GO/ZnO)as electrode material for the high-performance piroxicam sensor.The prepared glutathione-GO/ZnO nanocomposite was well characterized by X-ray diffraction(XRD),Fourier transform infrared spectrum(FTIR),X-ray photoelectron spectroscopy(XPS),field emission scanning electron microscopy(FE-SEM),cyclic voltammetry(CV),electrochemical impedance spectroscopy(EIS)and differential pulse voltammetry(DPV).The novel nanocomposite modified electrode showed the highest electrocatalytic activity towards piroxicam(oxidation potential is 0.52 V).Under controlled experimental parameters,the proposed sensor exhibited good linear responses to piroxicam concentrations ranging from 0.1 to 500 μM.The detection limit and sensitivity were calculated as 1.8 μM and 0.2 μA/μM·cm^(2),respectively.Moreover,it offered excellent selectivity,reproducibility,and long-term stability and can effectively ignore the interfering candidates commonly existing in the pharmaceutical tablets and human fluids even at a higher concentration.Finally,the reported sensor was successfully employed to the direct determination of piroxicam in practical samples.