Design of a Proportional-Integral-Derivative Controller for an Automatic Generation Control of Multi-area Power Thermal Systems Using Firefly Algorithm

Essentially, it is significant to supply the consumer with reliable and sufficient power. Since, power quality is measured by the consistency in frequency and power flow between control areas. Thus, in a power system operation and control,automatic generation control(AGC) plays a crucial role. In this paper, multi-area(Five areas: area 1, area 2, area 3, area 4 and area 5) reheat thermal power systems are considered with proportional-integral-derivative(PID) controller as a supplementary controller. Each area in the investigated power system is equipped with appropriate governor unit, turbine with reheater unit, generator and speed regulator unit. The PID controller parameters are optimized by considering nature bio-inspired firefly algorithm(FFA). The experimental results demonstrated the comparison of the proposed system performance(FFA-PID)with optimized PID controller based genetic algorithm(GAPID) and particle swarm optimization(PSO) technique(PSOPID) for the same investigated power system. The results proved the efficiency of employing the integral time absolute error(ITAE) cost function with one percent step load perturbation(1 % SLP) in area 1. The proposed system based FFA achieved the least settling time compared to using the GA or the PSO algorithms, while, it attained good results with respect to the peak overshoot/undershoot. In addition, the FFA performance is improved with the increased number of iterations which outperformed the other optimization algorithms based controller.

基于PSO-BP模糊PID的变距取苗机构控制系统设计

为满足番茄、辣椒等蔬菜作物的移栽需求,基于向下取苗原理设计了一种适用72穴和128穴两种主要番茄钵苗穴盘规格的变距取苗机构,通过建立数学模型获得了取苗机械手参数的目标函数,并利用粒子群和模拟退火混合算法对其结构参数进行优化。同时,为实现变距取苗机构的精确控制,提出了一种基于PSO-BP的模糊PID算法以提高控制精度,介绍了系统的结构与工作原理,并通过选型计算与分析建模建立了控制系统的数学模型。针对传统PID控制器稳定性差、响应速度慢等不足之处,利用PSO-BP模糊PID对控制器的参数进行在线调整,以满足控制过程中对参数的不同需求。仿真结果与试验数据的分析表明:在参数相同条件下,基于PSO-BP模糊PID控制系统系统稳定性更好、响应速度更快,具有良好的鲁棒性,提升取苗成功率的同时降低了基质损伤率,能够满足变距取苗机构高精度快速稳定控制的需求。

采摘机器人机械手避障方法研究——基于遗传优化和模糊PID控制器

为了提高采摘机器人机械手移动的自动化程度,使其在移动过程中有效避开障碍物,将基于PID控制器的避障系统引入到了机械手的设计上,并采用遗传算法和模糊算法对控制器进行了优化,提高了机械手移动的准确性和平稳性。模拟采摘机器人机械手的作业环境,对机械手的避障功能进行了测试,结果表明:机械手可以成功躲避障碍物,且采用遗传和模糊算法优化的机械手具有更高的移动平稳性,对于提高果实采摘效率和质量具有重要的作用。

基于遗传算法的汽车主动悬架变论域模糊PID控制

针对1/4车主动悬架系统,提出一种基于遗传算法(genetic algorithm,GA)的变论域模糊比例-积分-微分(proportional-integral-differential,PID)控制方法.在建立主动悬架系统模型的基础上,引入变论域思想设计模糊PID控制器.为进一步改善控制器减振效果,采用GA来优化变论域中伸缩因子描述函数的参数.结果表明:相比PID、模糊PID与未优化的变论域模糊PID等控制方法,基于GA的变论域模糊PID控制方法在降低车身垂向加速度、改善乘坐舒适性方面具有优越性;所提控制方法对簧载质量和车辆行驶速度不确定性具备较强的鲁棒性.

基于单片机和PID算法的温度智能控制系统设计

为提高温度控制的智能化水平,设计一种智能温度控制系统。该系统以STC89C52单片机为控制器,采用PID算法控制温度,具有语音播报和手机远程控制等功能。采用DS18B20温度传感器采集环境温度;设计LCD12864显示电路实时显示当前温度、温度上下限以及温度状态;设计WT588D语音提醒电路,当测量温度小于下限或大于上限时发出语音提醒;设计按键电路实现温度上下限值的设定;设计蓝牙通信电路,与手机APP通信,实现远程控制;采用PID算法输出控制量,控制固态继电器驱动加热或降温装置,实现温度控制。其次,对温度控制系统的硬件和软件进行设计,并制作实物进行运行测试。实验结果表明,所设计的温度控制系统能够很好地实现温度控制,从而达到预期效果,且操作方便、成本低,具有较强的应用价值。

采用改进BP-PID控制的机器人避障仿真研究

针对移动机器人避障过程中行驶路径长、寻路速度慢等问题,提出了一种改进反向传播-比例-积分-微分(BP-PID)控制器,并对移动机器人避障效果进行仿真验证。利用移动机器人在二维坐标系的避障简图,得出了移动机器人运动方程式。引用比例-积分-微分(PID)控制器和3层BP神经网络结构,利用BP神经网络的学习能力调整PID控制器参数。引用粒子群算法进行改进,通过改进粒子群算法在线优化BP-PID控制器,确保移动机器人BP-PID控制器收敛于全局最优值,从而使移动机器人避障效果更好。在不同环境中,采用Matlab软件对移动机器人避障效果进行仿真,比较改进前和改进后的移动机器人避障效果。结果显示:在不同环境中,改进前和改进后的BP-PID控制器均能使移动机器人安全地躲避障碍物;但是采用改进的粒子群算法优化BP-PID控制器,可以使移动机器人运动路径更短,迭代次数更少,搜索时间更短。采用改进BP-PID控制器,能够提高移动机器人避障过程中寻路速度,缩短行驶路径,效果更好。

基于位置式PID的水暖床垫温度控制系统设计

温度控制在生产生活中发挥着举足轻重的作用。位式控制算法在调节具有滞后性的水暖床垫温度控制系统时容易导致温度在目标值上下波动,控制效果不理想。为了解决此问题,设计了一种基于位置式PID的水暖床垫温度控制系统,系统以51内核的微处理器为核心控制器、以负温度系数热敏电阻(Negative Temperature Coefficient,NTC)为温度传感器、以PTC为加热器、以直流电机作为循环水泵。经实际测试结果表明,该系统运行稳定,控温精度在±0.5℃以内,达到了理想的温度控制效果。

基于粒子群优化模糊PID控制的水厂加氯系统

水厂加氯过程具有非线性、大时滞等特点,采用传统的PID控制方式难以实现消毒剂精准投加。因此,以某采用次氯酸钠消毒系统的水厂为例,首先通过分析该水厂加氯系统工作原理,结合工程经验和运行数据确定了加氯过程的近似数学模型。然后综合使用粒子群优化算法、模糊控制算法和PID控制算法,设计了一种粒子群优化模糊PID控制器,并利用MATLAB软件搭建了粒子群优化模糊PID控制系统和传统PID控制系统的模型进行仿真验证,结果表明:相较于传统PID控制系统,粒子群优化模糊PID控制系统的超调量减少了89.36%,调节时间减少了46.63%,其抗干扰能力也更强,系统整体控制效果有了较大提升。最后使用基于粒子群优化的模糊PID控制法对水厂加氯控制系统进行改造,试运行后发现,新系统控制效果良好,出厂水游离氯值能够稳定在设定值附近。

基于模糊-遗传算法的粗纱机出料传动系统PID参数优化方法

目前常规的粗纱机出料传动系统PID参数优化方法主要通过结合被控对象的稳态增益情况构建出优化函数,实现PID参数优化整合,忽略了实际运行工况下的干扰成分,导致参数优化效果不佳。对此,提出基于模糊-遗传算法的粗纱机出料传动系统PID参数优化方法。首先结合PID的系统阶跃响应曲线,以被控量的偏差变化率作为主要参数选取性能指标;然后通过引入负荷扰动模块以及频率干扰模块,对PID调节模块进行建模分析;最后结合模糊-遗传算法对最优适应度值进行求解,从而实现PID参数的有效优化,并对提出的方法进行优化效果检验。最终测试结果表明,采用提出的方法对PID参数进行优化整合时,控制输出曲线与理论输出曲线的拟合程度更高,具备较为理想的优化效果。

基于增量式PID算法的香精施加系统设计

为解决加热不燃烧烟草制品生产过程中香精施加量无法根据薄片质量变化进行实时调控的问题,设计了一种基于增量式PID算法的香精施加系统。该系统由称重单元、螺杆泵、喷嘴、流量传感器等组成,通过称重单元实时获取薄片质量数据,根据理论计算模型确定香精施加量,基于增量式PID算法驱动螺杆泵定量输出香精至喷嘴中,利用流量传感器对香精施加量实时反馈,实现香精精准施加。验证结果表明,当薄片质量发生变化时,香精施加量可快速调整,最大超调量为1%,最长调整时间为1.8 s,系统具有较好的跟踪性能;施加量检测值与理论值的偏移率为0.23%~0.52%,施加量组内波动为3.11%~4.17%,系统可实现香精的准确、均匀、稳定施加。

爆胎车辆动力学分析及模糊PID控制优化策略研究

车辆通过控制系统提高行驶的稳定性,但在爆胎时容易导致车辆行驶失去稳定性,从而造成车辆发生侧翻现象。为改善车辆动力学控制系统输出效果,建立了车辆轮胎动力学模型。引用模糊比例-积分-微分(PID)控制器,给出了模糊PID控制器输出参数与误差和误差变化率的关系图。提出人群搜索算法,利用人群搜索算法迭代搜索原理对模糊PID控制器参数进行寻优。以车辆2种行驶路况为例,利用Matlab软件对爆胎车辆的稳定性进行仿真,比较和分析爆胎车辆优化控制系统的输出效果。结果显示:采用模糊PID控制系统,爆胎车辆产生的偏航角、俯仰角加速度和侧倾角加速度较大。采用人群搜索算法优化模糊PID控制系统,爆胎车辆产生的偏航角、俯仰角加速度和侧倾角加速度较小。爆胎车辆采用人群搜索算法优化后的模糊PID控制器,不仅响应速度快,而且行驶的稳定性较好。

基于PPO的自适应PID控制算法研究

采用MATLAB物理引擎联合Python搭建了一个六轴机械臂,并模拟带有扰动的复杂控制环境,为机械臂训练提供现实中无法提供的试错环境。使用强化学习中近端优化算法(proximal policy optimization,PPO)算法对传统PID控制算法进行改进,引入多智能体思想,根据PID三个参数对控制系统的不同影响及六轴机械臂的特性,将三个参数分别作为不同的智能个体进行训练,实现多智能体自适应调整参数的新型多智能体自适应PID算法。仿真结果表明:该算法的训练收敛性优于MA-DDPG与MA-SAC算法,与传统PID算法的控制效果相比,在遇到扰动及振荡的情况下,能够更有效地抑制振荡,并具有更低的超调量和调整时间,控制过程更为平缓,有效提高了机械臂的控制精度,证明了该算法的鲁棒性及有效性。

基于改进粒子群算法优化PID控制的主动悬架性能研究

针对二自由度主动悬架比例-积分-微分(PID)控制器参数整定问题,引入粒子群算法,借助粒子群算法的全局搜索能力解决PID控制器参数整定问题,考虑到传统粒子群算法收敛速度较慢,设计了一种改进粒子群算法,根据悬架性能评价指标建立目标函数,分别模拟了随机路面激励输入和减速带式梯形冲击路面激励输入,并验证了基于改进粒子群算法优化的PID控制器的有效性。仿真结果表明:改进粒子群算法后目标函数的收敛速度明显提高;基于改进粒子群算法优化PID控制的主动悬架在不同激励输入条件下均具有较好的行驶平顺性;验证了改进粒子群算法的有效性并解决了PID控制器参数整定问题。

Novel Approach to Nonlinear PID Parameter Optimization Using Ant Colony Optimization Algorithm

This paper presents an application of an Ant Colony Optimization （ACO） algorithm to optimize the parameters in the design of a type of nonlinear PID controller. The ACO algorithm is a novel heuristic bionic algorithm, which is based on the behaviour of real ants in nature searching for food. In order to optimize the parameters of the nonlinear PID controller using ACO algorithm, an objective function based on position tracing error was constructed, and elitist strategy was adopted in the improved ACO algorithm. Detailed simulation steps are presented. This nonlinear PID controller using the ACO algorithm has high precision of control and quick response.

Design of PID controller with incomplete derivation based on ant system algorithm

A new and intelligent design method for PID controller with incomplete derivation is proposed based on the ant system algorithm ( ASA) . For a given control system with this kind of PID controller, a group of optimal PID controller parameters K p * , T i * , and T d * can be obtained by taking the overshoot, settling time, and steady-state error of the system's unit step response as the performance indexes and by use of our improved ant system algorithm. K p * , T i * , and T d * can be used in real-time control. This kind of controller is called the ASA-PID controller with incomplete derivation. To verify the performance of the ASA-PID controller, three different typical transfer functions were tested, and three existing typical tuning methods of PID controller parameters, including the Ziegler-Nichols method (ZN),the genetic algorithm (GA),and the simulated annealing (SA), were adopted for comparison. The simulation results showed that the ASA-PID controller can be used to control different objects and has better performance compared with the ZN-PID and GA-PID controllers, and comparable performance compared with the SA-PID controller.

Self-adaptive PID controller of microwave drying rotary device tuning on-line by genetic algorithms

The control design, based on self-adaptive PID with genetic algorithms(GA) tuning on-line was investigated, for the temperature control of industrial microwave drying rotary device with the multi-layer(IMDRDWM) and with multivariable nonlinear interaction of microwave and materials. The conventional PID control strategy incorporated with optimization GA was put forward to maintain the optimum drying temperature in order to keep the moisture content below 1%, whose adaptation ability included the cost function of optimization GA according to the output change. Simulations on five different industrial process models and practical temperature process control system for selenium-enriched slag drying intensively by using IMDRDWM were carried out systematically, indicating the reliability and effectiveness of control design. The parameters of proposed control design are all on-line implemented without iterative predictive calculations, and the closed-loop system stability is guaranteed, which makes the developed scheme simpler in its synthesis and application, providing the practical guidelines for the control implementation and the parameter design.

Improved quantum bacterial foraging algorithm for tuning parameters of fractional-order PID controller

The quantum bacterial foraging optimization(QBFO)algorithm has the characteristics of strong robustness and global searching ability. In the classical QBFO algorithm, the rotation angle updated by the rotation gate is discrete and constant,which cannot affect the situation of the solution space and limit the diversity of bacterial population. In this paper, an improved QBFO(IQBFO) algorithm is proposed, which can adaptively make the quantum rotation angle continuously updated and enhance the global search ability. In the initialization process, the modified probability of the optimal rotation angle is introduced to avoid the existence of invariant solutions. The modified operator of probability amplitude is adopted to further increase the population diversity.The tests based on benchmark functions verify the effectiveness of the proposed algorithm. Moreover, compared with the integerorder PID controller, the fractional-order proportion integration differentiation(PID) controller increases the complexity of the system with better flexibility and robustness. Thus the fractional-order PID controller is applied to the servo system. The tuning results of PID parameters of the fractional-order servo system show that the proposed algorithm has a good performance in tuning the PID parameters of the fractional-order servo system.

应用模糊PID自修正的电镀槽液温度控制方法

电镀槽液温度自动控制过程属于典型的混沌过程,在温度采集的过程中存在明显的非线性波动。典型的比例-积分-微分(PID)控制算法在这种混沌特性与非线性特性干扰下,存在控制精度较低、稳定性和鲁棒性较差等问题。此外,为解决非线性问题,PID算法需要循环迭代计算,存在控制时滞问题。以模糊控制为基础,提出了基于模糊PID的电镀槽液温度自动控制方法。该方法先设计温度数据采集结构,并将移动平均滤波、温度修正算法引入到采用的数据采集结构中,完成电镀槽液的实时温度数据采集。然后将采集到的温度数据作为构建的模糊PID控制器的输入。利用模糊控制规则引入修正因子,实现电镀槽液温度的自动控制。考虑到电镀槽液的时滞特性,在控制器中加入粗糙预估参考模型,对该特性加以抑制,提升控制性能。最后应用实验证明了所提方法的先进性。实验结果表明:所提方法具有较高的控制精度和效率,能够有效降低超调量和波动,应用效果较好。

Fractional order PID control for steer-by-wire system of emergency rescue vehicle based on genetic algorithm

Aiming at dealing with the difficulty for traditional emergency rescue vehicle(ECV)to enter into limited rescue scenes,the electro-hydraulic steer-by-wire(SBW)system is introduced to achieve the multi-mode steering of the ECV.The overall structure and mathematical model of the SBW system are described at length.The fractional order proportional-integral-derivative(FOPID)controller based on fractional calculus theory is designed to control the steering cylinder’s movement in SBW system.The anti-windup problem is considered in the FOPID controller design to reduce the bad influence of saturation.Five parameters of the FOPID controller are optimized using the genetic algorithm by maximizing the fitness function which involves integral of time by absolute value error(ITAE),peak overshoot,as well as settling time.The time-domain simulations are implemented to identify the performance of the raised FOPID controller.The simulation results indicate the presented FOPID controller possesses more effective control properties than classical proportional-integral-derivative(PID)controller on the part of transient response,tracking capability and robustness.

引入PID反馈的SHAEKF算法估算电池SOC

电池荷电状态(SOC)的估算精度是电动汽车电池组的重要指标。为提升SOC估算精度,在融合Sage-Husa扩展卡尔曼滤波(SHEKF)算法与自适应扩展卡尔曼滤波(AEKF)算法的基础上,增加比例积分微分(PID)反馈环节,形成改进算法。采用粒子群优化(PSO)算法对二阶RC等效电路模型进行参数辨识;用开源电池数据集对模型和算法进行实验和分析。改进的SHAEKF算法在电池动态应力测试(DST)、北京动态应力测试(BJDST)和美国联邦城市驾驶(FUDS)等工况下的平均估计误差都在1%以内,与单纯的融合算法SHAEKF算法相比,最大误差可减小5%。