The nitrogen-coordinated metal single-atom catalysts(M−N−C SACs)with an ultra-high metal loading synthetized by direct high-temperature pyrolysis have been widely reported.However,most of metal single atoms in these c...The nitrogen-coordinated metal single-atom catalysts(M−N−C SACs)with an ultra-high metal loading synthetized by direct high-temperature pyrolysis have been widely reported.However,most of metal single atoms in these catalysts were buried in the carbon matrix,resulting in a low metal utilization and inaccessibility for adsorption of reactants during the catalytic process.Herein,we reported a facile synthesis based on the hard-soft acid-base(HSAB)theory to fabricate Co single-atom catalysts with highly exposed metal atoms ligated to the external pyridinic-N sites of a nitrogen-doped carbon support.Benefiting from the highly accessible Co active sites,the prepared Co−N−C SAC exhibited a superior oxygen reduction reactivity comparable to that of the commercial Pt/C catalyst,showing a high turnover frequency(TOF)of 0.93 e^(−)·s^(-1)·site^(-1)at 0.85 V vs.RHE,far exceeding those of some representative SACs with a ultra-high metal content.This work provides a rational strategy to design and prepare M−N−C single-atom catalysts featured with high site-accessibility and site-density.展开更多
[目的]为进一步拓展单原子催化剂在亚硝酸盐还原制氨领域的应用,提出了一种铁-氮-碳(Fe-N-C)单原子催化剂电催化亚硝酸盐还原制氨的新体系.[方法]以二氧化硅为硬模板,2,6-二氨基吡啶为碳氮前驱体,硝酸铁为金属盐,通过“热解-刻蚀”策略...[目的]为进一步拓展单原子催化剂在亚硝酸盐还原制氨领域的应用,提出了一种铁-氮-碳(Fe-N-C)单原子催化剂电催化亚硝酸盐还原制氨的新体系.[方法]以二氧化硅为硬模板,2,6-二氨基吡啶为碳氮前驱体,硝酸铁为金属盐,通过“热解-刻蚀”策略制备了Fe-N-C单原子催化剂,并将其应用于亚硝酸盐制氨反应.[结果]多种结构表征结果显示,Fe-N-C催化剂表面的Fe物种呈现高度分散特征并以单原子形式存在.此外,Fe物种的化学环境主要是+2和+3价混合态,且通过与4个吡啶氮配位而稳定存在,即Fe-N-C催化剂的金属中心微观配位环境为Fe-N4结构.与纯氮碳(N-C)载体相比,本研究制备的Fe-N-C催化剂具有优异的亚硝酸盐还原性能,不仅表现出更高的起始还原电位(0 V vs可逆氢电极),具有接近100%的产氨法拉第效率和高的氨产率[8.4 mg/(h·cm^(2))],并且在连续20次催化循环测试中显示出优异的催化稳定性.[结论]本研究制备的Fe-N-C单原子催化剂对亚硝酸盐还原制氨具有优异的电催化活性,其高活性可能来源于对NO_(2)-的显著吸附,并进一步促进活性氢参与脱氧加氢过程.该Fe-N-C单原子催化亚硝酸盐还原体系可为后续合成氨的活性中心设计提供指导方向.展开更多
Platinum nanoparticles supported on carbons（Pt/C,60%,mass fraction） electrocatalysts for direct methanol fuel cell（DMFC） were prepared by citrate-stabilized method with different reductants and carbon supports.The...Platinum nanoparticles supported on carbons（Pt/C,60%,mass fraction） electrocatalysts for direct methanol fuel cell（DMFC） were prepared by citrate-stabilized method with different reductants and carbon supports.The catalysts were characterized by X-ray diffraction（XRD）,transmission electron microscopy（TEM） and cyclic voltammetry（CV）.It is found that the size of Pt nanoparticles on carbon is controllable by citrate addition and reductant optimization,and the form of carbon support has a great influence on electrocatalytic activity of catalysts.The citrate-stabilized Pt nanoparticles supported on BP2000 carbon,which was reduced by formaldehyde,exhibit the best performance with about 2 nm in diameter and 66.46 m2/g（Pt） in electrocatalytic active surface（EAS） area.Test on single DMFC with 60%（mass fraction） Pt/BP2000 as cathode electrocatalyst showed maximum power density at 78.8 mW/cm2.展开更多
A carbon supported Pd（Pd/C） catalyst used as the anodic catalyst in the direct formic acid fuel cells（DFAFC） was prepared via the improved complex reduction method with sodium ethylenediamine tetracetate（EDTA） a...A carbon supported Pd（Pd/C） catalyst used as the anodic catalyst in the direct formic acid fuel cells（DFAFC） was prepared via the improved complex reduction method with sodium ethylenediamine tetracetate（EDTA） as stabilizer and complexing agent. This method is very simple. The average size of the Pd particles in the Pd/C catalyst prepared with the improved complex reduction method is as small as about 2.1 nm and the Pd particles in the Pd/C catalyst possess an excellent uniformity. The Pd/C catalyst shows a high electrocatalytic activity and stability for the formic acid oxidation.展开更多
It is reported for the first time that the Pt/C catalyst can be prepared with a new and simple organic sol method using SnCl2 as the reductant. It was found that the average size of the Pt particles in the Pt/C cataly...It is reported for the first time that the Pt/C catalyst can be prepared with a new and simple organic sol method using SnCl2 as the reductant. It was found that the average size of the Pt particles in the Pt/C catalysts could be controlled with controlling the preparation conditions. The effect of the average sizes of the Pt particles in the Pt/C catalysts obtained with this method on the electrocatalytical activity of the oxidation of methanol was investigated.展开更多
The effect of acid component including various conventional acids and tungstic compounds on glucose hydrogenation over a series of binary catalyst system containing Ru/C catalyst was investigated. The results showed t...The effect of acid component including various conventional acids and tungstic compounds on glucose hydrogenation over a series of binary catalyst system containing Ru/C catalyst was investigated. The results showed that HC1, H2SO4, H3BO3, H3PO4, and HNO3 had negligible effect, while all the tungstic compounds imposed inhibiting effects on the hydrogenation of glucose over Ru/C catalyst, and the suppressing effect followed the order of H2WO4〉HPW〉WO3〉AMT〉HSiW. This order is the same as the order of ethylene glycol （EG） yields in the one-pot conversion of glucose to EG, suggesting the important role of competition between glucose hydrogenation and retro-aldol condensation in controlling the selectivity of EG.展开更多
Alloying degree, particle size and the level of dispersion are the key structural parameters of Pt-Ru/C catalyst in fuel cells. Solvent（s） used in the preparation process can affect the particle size and alloying de...Alloying degree, particle size and the level of dispersion are the key structural parameters of Pt-Ru/C catalyst in fuel cells. Solvent（s） used in the preparation process can affect the particle size and alloying degree of the object substance, which lead to a great positive impact on its properties. In this work, three types of solvents and their mixtures were used in preparation of the Pt-Ru/C catalysts by chemical reduction of metal precursors with sodium borohydride at room temperature. The structure of the catalysts was characterized by X-ray diffraction （XRD） and Transmission electron microscopy （TEM）. The catalytic activity and stability for methanol electro-oxidation were studied by Cyclic Voltammetry （CV） and Chronoamperometry （CA）. Pt-Ru/C catalyst prepared in H2O or binary solvents of H2O and isopropanol had large particle size and low alloying degree leading to low catalytic activity and less stability in methanol electro-oxidation. When tetrahydrofuran was added to the above solvent systems, Pt-Ru/C catalyst prepared had smaller particle size and higher alloying degree which resulted in better catalytic activity, lower onset and peak potentials, compared with the above catalysts. Moreover, the catalyst prepared in ternary solvents of isopropanol, water and tetrahydrofuran had the smallest particle size, and the high alloying degree and the dispersion kept unchanged. Therefore, this kind of catalyst showed the highest catalytic activity and good stability for methanol electro-oxidation.展开更多
Green and economical CO_(2)utilization is significant for CO_(2)emission reduction and energy development.Here,the 1D Mo_(2)C nanowires with dominant(101)crystal surfaces were modified by the deposition of atomic func...Green and economical CO_(2)utilization is significant for CO_(2)emission reduction and energy development.Here,the 1D Mo_(2)C nanowires with dominant(101)crystal surfaces were modified by the deposition of atomic functional components Rh and K.While unmodifiedβMo_(2)C could only convert CO_(2)to methanol,the designed catalyst of K_(0.2)Rh_(0.2)/β-Mo_(2)C exhibited up to 72.1%of ethanol selectivity at 150℃.It was observed that the atomically dispersed Rh could form the bifunctional active centres with the active carrierβMo_(2)C with the synergistic effects to achieve highly specific controlled C–C coupling.By promoting the CO_(2)adsorption and activation,the introduction of an alkali metal(K)mainly regulated the balanced performance of the two active centres,which in turn improved the hydrogenation selectivity.Overall,the controlled modification ofβMo_(2)C provides a new design strategy for the highly efficient,lowtemperature hydrogenation of CO_(2)to ethanol with single-atom catalysts,which provides an excellent example for the rational design of the complex catalysts.展开更多
Catalyst support is extremely important for future fuel cell devices.In this work,we developed doubleshelled C/TiO2(DSCT)hollow spheres as an excellent catalyst support via a template-directed method.The combination o...Catalyst support is extremely important for future fuel cell devices.In this work,we developed doubleshelled C/TiO2(DSCT)hollow spheres as an excellent catalyst support via a template-directed method.The combination of hollow structure,TiO2 shell and carbon layer results in excellent electron conductivity,electrocatalytic activity,and chemical stability.These uniformed DSCT hollow spheres are used as catalyst support to synthesize Pt/DSCT hollow spheres electrocatalyst.The resulting Pt/DSCT hollow spheres exhibited high catalytic performance with a current density of 462 mA mg^-1 for methanol oxidation reaction,which is 2.52 times higher than that of the commercial Pt/C.Furthermore,the increased tolerance to carbonaceous poisoning with a higher If/Ibratio and a better long-term stability in acid media suggests that the DSCT hollow sphere is a promising C/TiO2-based catalyst support for direct methanol fuel cells applications.展开更多
The Fischer–Tropsch to olefins（FTO） process is a method for the direct conversion of synthesis gas to lower C–Colefins. Carbon-supported iron carbide nanoparticles are attractive catalysts for this reaction.The ca...The Fischer–Tropsch to olefins（FTO） process is a method for the direct conversion of synthesis gas to lower C–Colefins. Carbon-supported iron carbide nanoparticles are attractive catalysts for this reaction.The catalytic activity can be improved and undesired formation of alkanes can be suppressed by the addition of sodium and sulfur as promoters but the influence of their content and ratio remains poorly understood and the promoted catalysts often suffer from rapid deactivation due to particle growth. A series of carbon black-supported iron catalysts with similar iron content and nominal sodium/sulfur loadings of 1–30/0.5–5 wt% with respect to iron are prepared and characterized under FTO conditions at 1and 10 bar syngas pressure to illuminate the influence of the promoter level on the catalytic properties.Iron particles and promoters undergo significant reorganization during FTO operation under industrially relevant conditions. Low sodium content（1–3 wt%） leads to a delay in iron carbide formation. Sodium contents of 15–30 wt% lead to rapid loss of catalytic activity due to the covering of the iron surface with promoters during particle growth under FTO operation. Higher activity and slower loss of activity are observed at low promoter contents（1–3 wt% sodium and 0.5–1 wt% sulfur） but a minimum amount of alkali is required to effectively suppress methane and C–Cparaffin formation. A reference catalyst support（carbide-derived carbon aerogel） shows that the optimum promoter level depends on iron particle size and support pore structure.展开更多
C1 chemistry based on synthesis gas, methane, and carbon dioxide offers many routes to industrial chemicals. The reactions related to the synthesis of gas can be classified into direct and indirect approach for making...C1 chemistry based on synthesis gas, methane, and carbon dioxide offers many routes to industrial chemicals. The reactions related to the synthesis of gas can be classified into direct and indirect approach for making such products, such as acetic acid, dimethyl ether, and alcohol. Catalytic syngas processing is currently done at high temperatures and pressures, conditions that could be unfavorable for the life of the catalyst. Another issue of C1 chemistry is related to the methane-initiated process. It has been known that direct methane conversions are still suffering from low yields and selectivity of products resulting in unprofitable ways to produce products, such as higher hydrocarbons, methanol, and so on. However, many experts and researchers are still trying to find the best method to overcome these barriers, for example, by finding the best catalyst to reduce the high-energy barrier of the reactions and conduct only selective catalyst-surface reactions. The appli- cation of Yttria-Stabilized Zirconia （YSZ） and its combination with other metals for catalyzing purposes are increasing. The existence of an interesting site that acts as oxygen store could be the main reason for it. Moreover, formation of intermediate species on the surface of YSZ also contributes significantly in increasing the production of some specific products. Understanding the phenomena happening inside could be necessary. In this article, the use of YSZ for some C1 chemistry reactions was discussed and reviewed.展开更多
The performance of lignin depolymerization is basically determined by the interunit C–O and C–C bonds.Numerous C–O bond cleavage strategies have been developed, while the cleavage of C–C bond between the primary a...The performance of lignin depolymerization is basically determined by the interunit C–O and C–C bonds.Numerous C–O bond cleavage strategies have been developed, while the cleavage of C–C bond between the primary aromatic units remains a challenging task due to the high dissociation energy of C–C bond.Herein, a multifunctional Ru Re alloy catalyst was designed, which exhibited exceptional catalytic activity for the cleavage of both C–O and C–C linkages in a broad range of lignin model compounds(β-1, a-5, 5–5,β-O-4, 4-O-5) and two stubborn lignins(kraft lignin and alkaline lignin), affording 97.5% overall yield of monocyclic compounds from model compounds and up to 129% of the maximum theoretical yield of monocyclic products based on C–O bonds cleavage from realistic lignin. Scanning transmission electron microscopy(STEM) characterization showed that Ru Re(1:1) alloy particles with hexagonal close-packed structure were homogeneously dispersed on the support. Quasi-in situ X-ray photoelectron spectroscopy(XPS), and X-ray absorption spectroscopy(XAS) indicate that Ru species were predominantly metallic state, whereas Re species were partially oxidized;meanwhile, there was a strong interaction between Ru and Re, where the electron transfer from Re to Ru was occurred, resulting in great improvement on the capability of C–O and C–C bonds cleavage in lignin conversion.展开更多
The catalyst screening tests for carbon dioxide oxidative coupling of methane (CO2-OCM) have been investigated over ternary and binary metal oxide catalysts. The catalysts are prepared by doping MgO- and CeO2-based so...The catalyst screening tests for carbon dioxide oxidative coupling of methane (CO2-OCM) have been investigated over ternary and binary metal oxide catalysts. The catalysts are prepared by doping MgO- and CeO2-based solids with oxides from alkali (Li2O), alkaline earth (CaO), and transition metal groups (WO3 or MnO). The presence of the peroxide (O2-2) active sites on the Li2O2, revealed by Raman spectroscopy, may be the key factor in the enhanced performance of some of the Li2O/MgO catalysts. The high reducibility of the CeO2 catalyst, an important factor in the CO2-OCM catalyst activity, may be enhanced by the presence of manganese oxide species. The manganese oxide species increases oxygen mobility and oxygen vacancies in the CeO2 catalyst. Raman and Fourier Transform Infra Red (FT-IR) spectroscopies revealed the presence of lattice vibrations of metal-oxygen bondings and active sites in which the peaks corresponding to the bulk crystalline structures of Li2O, CaO, WO3 and MnO are detected. The performance of 5%MnO/15%CaO/CeO2 catalyst is the most potential among the CeO2-based catalysts, although lower than the 2%Li2O/MgO catalyst. The 2%Li2O/MgO catalyst showed the most promising C2+ hydrocarbons selectivity and yield at 98.0% and 5.7%, respectively.展开更多
Supported PtRu/C catalysts used in direct methanol fuel cells (DMFCs) were prepared by a new modified polyol method. Transmission electron microscopy (TEM), X-ray diffraction (XRD) and cyclic voltammograms (CVs) were ...Supported PtRu/C catalysts used in direct methanol fuel cells (DMFCs) were prepared by a new modified polyol method. Transmission electron microscopy (TEM), X-ray diffraction (XRD) and cyclic voltammograms (CVs) were carried out to characterize the morphology, composition and the electrochemical properties of the PtRu/C catalyst. The results revealed that the PtRu nanoparticles with small average particle size (≈2.5 nm), and highly dispersed on the carbon support. The PtRu/C catalyst exhibited high catalytic activity and anti poisoned performance than that of the JM PtRu/C. It is imply that the modified polyol method is efficient for PtRu/C catalyst preparation.展开更多
The results of commercial application of two types of C_8 aromatics isomerization catalysts under different feed conditions were compared to gain an insight in the techno-economical basis for selecting proper technolo...The results of commercial application of two types of C_8 aromatics isomerization catalysts under different feed conditions were compared to gain an insight in the techno-economical basis for selecting proper technological route at the plant.The comparison reveals differences in every aspect of feed consumption,unit capacity,product output,product distribution,and unit process parameters depending upon which catalyst type is adopted by the integrated PX complex.The type of aromatics isomerization catalyst has its influence on the plant scale,the construction cost,the process unit capacity and the product cost,with the magnitude of its impact varying with changing feed conditions.展开更多
基金supported by Shanxi Province Science Foundation for Youths(202203021212300)Taiyuan University of Science and Technology Scientific Research Initial Funding(20212064)Outstanding Doctoral Award Fund in Shanxi Province(20222060).
文摘The nitrogen-coordinated metal single-atom catalysts(M−N−C SACs)with an ultra-high metal loading synthetized by direct high-temperature pyrolysis have been widely reported.However,most of metal single atoms in these catalysts were buried in the carbon matrix,resulting in a low metal utilization and inaccessibility for adsorption of reactants during the catalytic process.Herein,we reported a facile synthesis based on the hard-soft acid-base(HSAB)theory to fabricate Co single-atom catalysts with highly exposed metal atoms ligated to the external pyridinic-N sites of a nitrogen-doped carbon support.Benefiting from the highly accessible Co active sites,the prepared Co−N−C SAC exhibited a superior oxygen reduction reactivity comparable to that of the commercial Pt/C catalyst,showing a high turnover frequency(TOF)of 0.93 e^(−)·s^(-1)·site^(-1)at 0.85 V vs.RHE,far exceeding those of some representative SACs with a ultra-high metal content.This work provides a rational strategy to design and prepare M−N−C single-atom catalysts featured with high site-accessibility and site-density.
文摘[目的]为进一步拓展单原子催化剂在亚硝酸盐还原制氨领域的应用,提出了一种铁-氮-碳(Fe-N-C)单原子催化剂电催化亚硝酸盐还原制氨的新体系.[方法]以二氧化硅为硬模板,2,6-二氨基吡啶为碳氮前驱体,硝酸铁为金属盐,通过“热解-刻蚀”策略制备了Fe-N-C单原子催化剂,并将其应用于亚硝酸盐制氨反应.[结果]多种结构表征结果显示,Fe-N-C催化剂表面的Fe物种呈现高度分散特征并以单原子形式存在.此外,Fe物种的化学环境主要是+2和+3价混合态,且通过与4个吡啶氮配位而稳定存在,即Fe-N-C催化剂的金属中心微观配位环境为Fe-N4结构.与纯氮碳(N-C)载体相比,本研究制备的Fe-N-C催化剂具有优异的亚硝酸盐还原性能,不仅表现出更高的起始还原电位(0 V vs可逆氢电极),具有接近100%的产氨法拉第效率和高的氨产率[8.4 mg/(h·cm^(2))],并且在连续20次催化循环测试中显示出优异的催化稳定性.[结论]本研究制备的Fe-N-C单原子催化剂对亚硝酸盐还原制氨具有优异的电催化活性,其高活性可能来源于对NO_(2)-的显著吸附,并进一步促进活性氢参与脱氧加氢过程.该Fe-N-C单原子催化亚硝酸盐还原体系可为后续合成氨的活性中心设计提供指导方向.
基金Project(50573041)supported by the National Natural Science Foundation of China
文摘Platinum nanoparticles supported on carbons（Pt/C,60%,mass fraction） electrocatalysts for direct methanol fuel cell（DMFC） were prepared by citrate-stabilized method with different reductants and carbon supports.The catalysts were characterized by X-ray diffraction（XRD）,transmission electron microscopy（TEM） and cyclic voltammetry（CV）.It is found that the size of Pt nanoparticles on carbon is controllable by citrate addition and reductant optimization,and the form of carbon support has a great influence on electrocatalytic activity of catalysts.The citrate-stabilized Pt nanoparticles supported on BP2000 carbon,which was reduced by formaldehyde,exhibit the best performance with about 2 nm in diameter and 66.46 m2/g（Pt） in electrocatalytic active surface（EAS） area.Test on single DMFC with 60%（mass fraction） Pt/BP2000 as cathode electrocatalyst showed maximum power density at 78.8 mW/cm2.
基金Supported by the "863" Program of Science and Technology Ministry of China(Nos.2006AA05Z137, 2007AA05Z143 and 2007AA05Z159)National Natural Science Foundation of China(Nos.20433060, 20473038, 20573057 and 20703043)the Natural Science Foundation of Jiangsu Province, China(No.BK2006224).
文摘A carbon supported Pd（Pd/C） catalyst used as the anodic catalyst in the direct formic acid fuel cells（DFAFC） was prepared via the improved complex reduction method with sodium ethylenediamine tetracetate（EDTA） as stabilizer and complexing agent. This method is very simple. The average size of the Pd particles in the Pd/C catalyst prepared with the improved complex reduction method is as small as about 2.1 nm and the Pd particles in the Pd/C catalyst possess an excellent uniformity. The Pd/C catalyst shows a high electrocatalytic activity and stability for the formic acid oxidation.
文摘It is reported for the first time that the Pt/C catalyst can be prepared with a new and simple organic sol method using SnCl2 as the reductant. It was found that the average size of the Pt particles in the Pt/C catalysts could be controlled with controlling the preparation conditions. The effect of the average sizes of the Pt particles in the Pt/C catalysts obtained with this method on the electrocatalytical activity of the oxidation of methanol was investigated.
基金supported by the National Natural Science Foundation of China(Grants 21176235 and 21206159)
文摘The effect of acid component including various conventional acids and tungstic compounds on glucose hydrogenation over a series of binary catalyst system containing Ru/C catalyst was investigated. The results showed that HC1, H2SO4, H3BO3, H3PO4, and HNO3 had negligible effect, while all the tungstic compounds imposed inhibiting effects on the hydrogenation of glucose over Ru/C catalyst, and the suppressing effect followed the order of H2WO4〉HPW〉WO3〉AMT〉HSiW. This order is the same as the order of ethylene glycol （EG） yields in the one-pot conversion of glucose to EG, suggesting the important role of competition between glucose hydrogenation and retro-aldol condensation in controlling the selectivity of EG.
基金supported by 863 Project(No.2006AA05Z102)the Cultivation Fund of the Key Scientific and Technical Innovation Project,Ministry of Education of China (No.707050)+1 种基金Specialized Research Fund for the Doctoral Program of Higher Education (No.20060610023)Chengdu Natural Science Foundation (Nos.06GGYB449GX-030,and 07GGZD139GX)
文摘Alloying degree, particle size and the level of dispersion are the key structural parameters of Pt-Ru/C catalyst in fuel cells. Solvent（s） used in the preparation process can affect the particle size and alloying degree of the object substance, which lead to a great positive impact on its properties. In this work, three types of solvents and their mixtures were used in preparation of the Pt-Ru/C catalysts by chemical reduction of metal precursors with sodium borohydride at room temperature. The structure of the catalysts was characterized by X-ray diffraction （XRD） and Transmission electron microscopy （TEM）. The catalytic activity and stability for methanol electro-oxidation were studied by Cyclic Voltammetry （CV） and Chronoamperometry （CA）. Pt-Ru/C catalyst prepared in H2O or binary solvents of H2O and isopropanol had large particle size and low alloying degree leading to low catalytic activity and less stability in methanol electro-oxidation. When tetrahydrofuran was added to the above solvent systems, Pt-Ru/C catalyst prepared had smaller particle size and higher alloying degree which resulted in better catalytic activity, lower onset and peak potentials, compared with the above catalysts. Moreover, the catalyst prepared in ternary solvents of isopropanol, water and tetrahydrofuran had the smallest particle size, and the high alloying degree and the dispersion kept unchanged. Therefore, this kind of catalyst showed the highest catalytic activity and good stability for methanol electro-oxidation.
基金financially supported by the National Natural Science Foundation of China(21925803,U19A2015)the Strategic Priority Research Program of the Chinese Academy of Sciences(XDB36030200)the Liao Ning Revitalization Talents Program(XLYC1907170).
文摘Green and economical CO_(2)utilization is significant for CO_(2)emission reduction and energy development.Here,the 1D Mo_(2)C nanowires with dominant(101)crystal surfaces were modified by the deposition of atomic functional components Rh and K.While unmodifiedβMo_(2)C could only convert CO_(2)to methanol,the designed catalyst of K_(0.2)Rh_(0.2)/β-Mo_(2)C exhibited up to 72.1%of ethanol selectivity at 150℃.It was observed that the atomically dispersed Rh could form the bifunctional active centres with the active carrierβMo_(2)C with the synergistic effects to achieve highly specific controlled C–C coupling.By promoting the CO_(2)adsorption and activation,the introduction of an alkali metal(K)mainly regulated the balanced performance of the two active centres,which in turn improved the hydrogenation selectivity.Overall,the controlled modification ofβMo_(2)C provides a new design strategy for the highly efficient,lowtemperature hydrogenation of CO_(2)to ethanol with single-atom catalysts,which provides an excellent example for the rational design of the complex catalysts.
基金supported by the Scholarship from China Scholarship Council(CSC)(Grant no.201604910621)。
文摘Catalyst support is extremely important for future fuel cell devices.In this work,we developed doubleshelled C/TiO2(DSCT)hollow spheres as an excellent catalyst support via a template-directed method.The combination of hollow structure,TiO2 shell and carbon layer results in excellent electron conductivity,electrocatalytic activity,and chemical stability.These uniformed DSCT hollow spheres are used as catalyst support to synthesize Pt/DSCT hollow spheres electrocatalyst.The resulting Pt/DSCT hollow spheres exhibited high catalytic performance with a current density of 462 mA mg^-1 for methanol oxidation reaction,which is 2.52 times higher than that of the commercial Pt/C.Furthermore,the increased tolerance to carbonaceous poisoning with a higher If/Ibratio and a better long-term stability in acid media suggests that the DSCT hollow sphere is a promising C/TiO2-based catalyst support for direct methanol fuel cells applications.
基金supported by a Post Doc grant of the German Academic Exchange Service(Deutscher Akademischer Austauschdienst,DAAD grant no.91552012)by the European Research Council(EU FP7 ERC advanced grant no.338846)
文摘The Fischer–Tropsch to olefins（FTO） process is a method for the direct conversion of synthesis gas to lower C–Colefins. Carbon-supported iron carbide nanoparticles are attractive catalysts for this reaction.The catalytic activity can be improved and undesired formation of alkanes can be suppressed by the addition of sodium and sulfur as promoters but the influence of their content and ratio remains poorly understood and the promoted catalysts often suffer from rapid deactivation due to particle growth. A series of carbon black-supported iron catalysts with similar iron content and nominal sodium/sulfur loadings of 1–30/0.5–5 wt% with respect to iron are prepared and characterized under FTO conditions at 1and 10 bar syngas pressure to illuminate the influence of the promoter level on the catalytic properties.Iron particles and promoters undergo significant reorganization during FTO operation under industrially relevant conditions. Low sodium content（1–3 wt%） leads to a delay in iron carbide formation. Sodium contents of 15–30 wt% lead to rapid loss of catalytic activity due to the covering of the iron surface with promoters during particle growth under FTO operation. Higher activity and slower loss of activity are observed at low promoter contents（1–3 wt% sodium and 0.5–1 wt% sulfur） but a minimum amount of alkali is required to effectively suppress methane and C–Cparaffin formation. A reference catalyst support（carbide-derived carbon aerogel） shows that the optimum promoter level depends on iron particle size and support pore structure.
基金Project supported by the Global R&D Program of the Korea Foundation for International Cooperation of Science and Technology (KICOS)
文摘C1 chemistry based on synthesis gas, methane, and carbon dioxide offers many routes to industrial chemicals. The reactions related to the synthesis of gas can be classified into direct and indirect approach for making such products, such as acetic acid, dimethyl ether, and alcohol. Catalytic syngas processing is currently done at high temperatures and pressures, conditions that could be unfavorable for the life of the catalyst. Another issue of C1 chemistry is related to the methane-initiated process. It has been known that direct methane conversions are still suffering from low yields and selectivity of products resulting in unprofitable ways to produce products, such as higher hydrocarbons, methanol, and so on. However, many experts and researchers are still trying to find the best method to overcome these barriers, for example, by finding the best catalyst to reduce the high-energy barrier of the reactions and conduct only selective catalyst-surface reactions. The appli- cation of Yttria-Stabilized Zirconia （YSZ） and its combination with other metals for catalyzing purposes are increasing. The existence of an interesting site that acts as oxygen store could be the main reason for it. Moreover, formation of intermediate species on the surface of YSZ also contributes significantly in increasing the production of some specific products. Understanding the phenomena happening inside could be necessary. In this article, the use of YSZ for some C1 chemistry reactions was discussed and reviewed.
基金The National Natural Science Foundation of China(22078317,21878288,21721004,21690083)。
文摘The performance of lignin depolymerization is basically determined by the interunit C–O and C–C bonds.Numerous C–O bond cleavage strategies have been developed, while the cleavage of C–C bond between the primary aromatic units remains a challenging task due to the high dissociation energy of C–C bond.Herein, a multifunctional Ru Re alloy catalyst was designed, which exhibited exceptional catalytic activity for the cleavage of both C–O and C–C linkages in a broad range of lignin model compounds(β-1, a-5, 5–5,β-O-4, 4-O-5) and two stubborn lignins(kraft lignin and alkaline lignin), affording 97.5% overall yield of monocyclic compounds from model compounds and up to 129% of the maximum theoretical yield of monocyclic products based on C–O bonds cleavage from realistic lignin. Scanning transmission electron microscopy(STEM) characterization showed that Ru Re(1:1) alloy particles with hexagonal close-packed structure were homogeneously dispersed on the support. Quasi-in situ X-ray photoelectron spectroscopy(XPS), and X-ray absorption spectroscopy(XAS) indicate that Ru species were predominantly metallic state, whereas Re species were partially oxidized;meanwhile, there was a strong interaction between Ru and Re, where the electron transfer from Re to Ru was occurred, resulting in great improvement on the capability of C–O and C–C bonds cleavage in lignin conversion.
文摘The catalyst screening tests for carbon dioxide oxidative coupling of methane (CO2-OCM) have been investigated over ternary and binary metal oxide catalysts. The catalysts are prepared by doping MgO- and CeO2-based solids with oxides from alkali (Li2O), alkaline earth (CaO), and transition metal groups (WO3 or MnO). The presence of the peroxide (O2-2) active sites on the Li2O2, revealed by Raman spectroscopy, may be the key factor in the enhanced performance of some of the Li2O/MgO catalysts. The high reducibility of the CeO2 catalyst, an important factor in the CO2-OCM catalyst activity, may be enhanced by the presence of manganese oxide species. The manganese oxide species increases oxygen mobility and oxygen vacancies in the CeO2 catalyst. Raman and Fourier Transform Infra Red (FT-IR) spectroscopies revealed the presence of lattice vibrations of metal-oxygen bondings and active sites in which the peaks corresponding to the bulk crystalline structures of Li2O, CaO, WO3 and MnO are detected. The performance of 5%MnO/15%CaO/CeO2 catalyst is the most potential among the CeO2-based catalysts, although lower than the 2%Li2O/MgO catalyst. The 2%Li2O/MgO catalyst showed the most promising C2+ hydrocarbons selectivity and yield at 98.0% and 5.7%, respectively.
文摘Supported PtRu/C catalysts used in direct methanol fuel cells (DMFCs) were prepared by a new modified polyol method. Transmission electron microscopy (TEM), X-ray diffraction (XRD) and cyclic voltammograms (CVs) were carried out to characterize the morphology, composition and the electrochemical properties of the PtRu/C catalyst. The results revealed that the PtRu nanoparticles with small average particle size (≈2.5 nm), and highly dispersed on the carbon support. The PtRu/C catalyst exhibited high catalytic activity and anti poisoned performance than that of the JM PtRu/C. It is imply that the modified polyol method is efficient for PtRu/C catalyst preparation.
文摘The results of commercial application of two types of C_8 aromatics isomerization catalysts under different feed conditions were compared to gain an insight in the techno-economical basis for selecting proper technological route at the plant.The comparison reveals differences in every aspect of feed consumption,unit capacity,product output,product distribution,and unit process parameters depending upon which catalyst type is adopted by the integrated PX complex.The type of aromatics isomerization catalyst has its influence on the plant scale,the construction cost,the process unit capacity and the product cost,with the magnitude of its impact varying with changing feed conditions.
