Indirect Vector Control of Linear Induction Motors Using Space Vector Pulse Width Modulation

Vector control schemes have recently been used to drive linear induction motors(LIM)in high-performance applications.This trend promotes the development of precise and efficient control schemes for individual motors.This research aims to present a novel framework for speed and thrust force control of LIM using space vector pulse width modulation(SVPWM)inverters.The framework under consideration is developed in four stages.To begin,MATLAB Simulink was used to develop a detailed mathematical and electromechanical dynamicmodel.The research presents a modified SVPWM inverter control scheme.By tuning the proportional-integral(PI)controller with a transfer function,optimized values for the PI controller are derived.All the subsystems mentioned above are integrated to create a robust simulation of the LIM’s precise speed and thrust force control scheme.The reference speed values were chosen to evaluate the performance of the respective system,and the developed system’s response was verified using various data sets.For the low-speed range,a reference value of 10m/s is used,while a reference value of 100 m/s is used for the high-speed range.The speed output response indicates that themotor reached reference speed in amatter of seconds,as the delay time is between 8 and 10 s.The maximum amplitude of thrust achieved is less than 400N,demonstrating the controller’s capability to control a high-speed LIM with minimal thrust ripple.Due to the controlled speed range,the developed system is highly recommended for low-speed and high-speed and heavy-duty traction applications.

A Pulse Width Modulation Scheme With Zero-sequence Voltage Injection for Single Phase Three-level NPC Rectifiers

直流侧中点电位电压偏移是多电平中性点钳位型变流器的主要缺点。以单相三电平NPC整流器为研究对象，以实现直流侧中点电位无漂移为控制目标，以传统的单相三电平单极性载波脉宽调制方法为基础，首先提出一种基于零序电压分量注入的载波脉宽调制算法；然后在此基础上给出基于零序电压分量极限值注入的载波脉宽调制算法；并给出这2种方法的零序电压分量的设计方案；最后，对这2种方法进行了详细的理论分析、计算机仿真和1kW样机实验对比验证。研究结果表明：所提出的2种算法都能有效实现直流侧中点电位平衡控制，其中基于零序电压分量极限值注入的载波调制算法的中点电位控制具有更快动态响应速度，且其网侧电流的高次谐波主要分布在开关频率附近；而基于零序电压分量注入的载波调制算法的网侧电流高次谐波主要分布在2倍开关频率附近。但是在一个调制信号周期内，基于零序电压分量极限值注入的载波调制算法的开关切换次数比基于零序电压分量注入的载波调制算法低25％左右。

Comparison of performance between bipolar and unipolar double-frequency sinusoidal pulse width modulation in a digitally controlled H-bridge inverter system

By deriving the discrete-time models of a digitally controlled H-bridge inverter system modulated by bipolar sinu- soidal pulse width modulation （BSPWM） and unipolar double-frequency sinusoidal pulse width modulation （UDFSPWM） respectively, the performances of the two modulation strategies are analyzed in detail. The circuit parameters, used in this paper, are fixed. When the systems, modulated by BSPWM and UDFSPWM, have the same switching frequency, the stabil- ity boundaries of the two systems are the same. However, when the equivalent switching frequencies of the two systems are the same, the BSPWM modulated system is more stable than the UDFSPWM modulated system. In addition, a convenient method of establishing the discrete-time model of piecewise smooth system is presented. Finally, the analytical results are confirmed by circuit simulations and experimental measurements.

Realization of Space Vector Pulse Width Modulation Method Based on DSP

In order to compensate for the deficiency of Sine Pulse Width Modulation（SPWM）, on the base of analyzing the principle of space w tot pulse width modulation and being compared with SPWM, the method of solving working time of adjacent vector and the method of generate space voltage vector were introduced. The experiment to the inverter which consists of IGBT proves that SVPWM centrol algorithm can reduce harmonic effectively, it is beneficial to enhancing the utilization rate of voltage source inverter direct current power supply.

Research and Making of a High-Power Switching Supply Using Pulse Width Modulation

Compared with the traditional SCR phase-shift regulated power supply, a new type of power semiconductor , noncrystalline state magnetic material and pulse width modulation technology, high-power switching supply has many advantages： small volume, high converting efficiency, good dynamic performance, small harmonic componont and small pollution to AC supply.

Digital Pulse Width Modulation Control in Power Electronic Circuits Design

The paper mainly focuses on the digital pulse width modulation (DPWM) control techniques for high performance power electronic circuit design. The problem to be solved in this study addresses the DPWM converter design for DC to DC conversion process. The control techniques have been utilized the Fuzzy Logic Rules Base method for proposed SIMULINK model of high performance power electronic circuit. The analytical calculations for real circuit design have been completed based on the mathematical modeling of the system. The results from the developed SIMULINK model confirm the target specifications of the high performance condition for power electronic circuit which was met the objective of this study. The numerical results have been carried out with the help of MATLAB/SIMULINK.

Improved Protein Transfer Efficiency and Signal Intensity in BlotMan Using Pulse Width Modulation

BlotMan is a protein blotting device that allows generating multiple membranes from a single polyacrylamide gel. To transfer all proteins uniformly with the same efficiency regardless of protein size, BlotMan employs pulse-width-modulated (PWM) voltage that applies a higher average voltage to a larger protein species. BlotMan can be controlled not only by its custom-made interface but also by a smart phone via Bluetooth technology. In this study, we examined effects of PWM signals (50%, 60%, and 80% duty cycle) on transfer efficiency and signal intensity in comparison to a constant voltage signal (100% duty cycle). The result revealed that in response to the same average voltage of 150 V, a lower duty cycle with a higher maximum voltage increased transfer efficiency as well as sharpness of transferred proteins. We validated BlotMan’s capability using a chondrosarcoma cell line (SW1353 cells) and a breast cancer cell line (MDA-MB231 cells) in response to antitumor chemical agents. BlotMan successfully generated 5 membranes from a single gel and detected 5 protein species such as c-Src, eukaryotic translation initiation factor 2 alpha (eIF2), phosphorylated eIF2, lamin B, and actin. Collectively, we demonstrated herein that BlotMan reduces an amount of protein samples by generating multiple membranes from a single gel and improving signal intensity with PWM voltage signals.

Capacitor Pattern H-Bridge Multilevel Inverter (CPHMLI) Using Phase Diposition Pulse Width Modulation for Grid Applications

This work presents an implementation of an innovative single phase multilevel inverter using capacitors with reduced switches. The proposed Capacitor pattern H-bridge Multilevel Inverter (CPHMLI) topology consists of a proper number of Capacitor connected with switches and power sources. The advanced switching control supplied by Pulse Width Modulation (PDPWM) to attain mixed staircase switching state. The charging and discharging mode are achieved by calculating the voltage error at the load. Furthermore, to accomplish the higher voltage levels at the output with less number of semiconductors switches and simple commutation designed using CPHMLI topology. To prove the performance and effectiveness of the proposed approach, a set of experiments performed under various load conditions using MATLAB tool.

Spectral Calculation of the Output Voltage of an Inverter with Bipolar Pulse Width Modulation

Converters with pulse width modulation are used for connections between the direct current （DC） and alternating current （AC） networks, e.g., in uninterrupted power supply systems, AC electromotor drives, for powering induction furnaces, in audio technique. Spectrum of signals sampled by pulse amplitude modulation and output voltage spectrum of the converter with pulse width modulation have similar properties. Spectrum of signals sampled by pulse amplitude modulation contains a harmonic of frequency equal to the frequency of the modulating signal and the harmonics of frequencies equal to the sum of frequency of the modulating signal and multiples of the sampling frequency. The output voltage spectrum of the converter with bipolar pulse width modulation contains harmonic of frequency equal to the frequency of the modulating signal and harmonics of frequencies equal to sum of the frequency of the modulating signal and multiples of the frequency of the carrier signal. It also contains harmonics of frequencies equal to the sum of the multiples of the frequency of the modulating signal and the multiples of the carrier signal. The comparison analysis was carried out for the harmonics of the output voltage of the converter with bipolar pulse width modulation in time domain. The dependency of the amplitudes and frequency spectrum on the wave forms of the carrier signal and modulating signal was shown. Similarity of the output voltage spectrum of the converter and signal spectrum sampled by the pulse width modulation was also shown. Key words： Output voltage converter with bipolar pulse width modulation, spectral analysis, Fourier series, carrier signal, reference signal.

Temporal characteristic analysis of single event effects in pulse width modulator

In this paper,the nature and origin of single event effects(SEE) are studied by injecting laser pulses into different circuit blocks,combining with analysis to map pulse width modulators circuitry in the microchip die.A time-domain error-identification method is used in the temporal characteristic analysis of SEE.SEE signatures of different injection times are compared.More serious SEE are observed when the laser shot occurs on a rising edge of the device output for blocks of the error amplifier,current sense comparator,and T and SR latches.

An Improved Submodule Unified Pulse Modulation Scheme for a Hybrid Modular Multilevel Converter

This paper presents an improved submodule unified pulse width modulation(SUPWM)scheme for a hybrid modular multilevel converter(MMC)composed of half-bridge submodules(HBSMs)and full-bridge submodules(FBSMs).The proposed SUPWM scheme can achieve an output voltage of(2N+1)(where N is the number of submodules in each arm)levels,which is the same as that of the carrier-phase-shifted PWM(CPSPWM)scheme.Meanwhile,the proposed SUPWM scheme can alleviate the uneven loss distributions between the left leg and right leg in FBSMs of the hybrid MMC.Moreover,the capacitor voltages of the sub-modules can be well balanced without complicated closed-loop voltage balancing controllers.The validity of the proposed SUPWM scheme is verified by both the simulated and experimental results.

Evaluation of a Pulse Width Modulated Bypass Nozzle for the Development of a Variable Load Residential Oil Burner

Due to the need for energy conservation in buildings and the simultaneous benefit of cost savings, the development of a low firing rate load modulating residential oil burner is very desirable. One of the two main requirements of such a burner is the development of a burner nozzle that is able to maintain the particle size distribution of the fuel spray in the desirable (small) size range for efficient and stable combustion. The other being the ability to vary the air flow rate and air distribution around the fuel nozzle in the burner for optimal combustion at the current fuel firing rate. In this paper, which deals with the first requirement, we show that by using pulse width modulation in the bypass channel of a commercial off-the-shelf bypass nozzle, this objective can be met. Here we present results of spray patterns and particle size distribution for a range of fuel firing rates. The results show that a desirable fuel spray pattern can be maintained over a fuel firing rate turndown ratio (Maximum Fuel Flow Rate/Minimum Fuel Flow Rate) of 3.7. Thus here we successfully demonstrate the ability to electronically vary the fuel firing rate by more than a factor of 3 while simultaneously maintaining good atomization.

A Kind of PWM Pneumatic Servo Control System——Modulation Methods and Dynamic Responses

Vibrations or dither's are features of the PWM servo control system in their steady outputs. On the grounds of analyses and experiments of a PWM pneumatic servo control system, the paper puts forward four varieties of PWM modulation methods, and concludes on the relationship between dithers and the different methods, and then discusses the influence of friction to the dithers. Results from experiments regarding the dynamic and static responses on the given system support the theories presented.

基于虚拟电压矢量的双三相直线磁通切换永磁电机容错SVPWM策略

高可靠性是电梯驱动系统的首要指标。针对双三相直线磁通切换永磁(dual-three-phase linear flux switching permanent magnet,DTP-LFSPM)电机单相开路故障,提出一种基于虚拟电压矢量的容错空间矢量脉宽调制策略。首先,基于单相开路故障下的五维变换矩阵计算得到故障后的32个空间电压矢量分布。然后,筛选部分空间电压矢量,以z子空间电压幅值为零且每个扇区产生对称的脉宽调制波形为目标,重构得到12个虚拟电压矢量,相邻的2个虚拟电压矢量都由3个基本电压矢量组成,并用于合成参考电压矢量,不仅可以减少单相开路故障容错控制时的电流谐波,而且具有计算简单,易于硬件实现等优点。最后,搭建DTP-LFSPM电机驱动控制系统仿真与实验平台,仿真和实验测试结果证明所提容错策略的正确性和有效性。

抑制级联H 桥变换器共模电压的简化SVPWM 策略

为解决传统空间矢量调制策略难以拓展至高电平数级联H桥多电平变换器,以及抑制级联H桥多电平变换器调制策略实现过程中产生的共模电压的问题,本文提出一种简化空间矢量调制策略。该策略基于α'β'坐标系,通过判断空间矢量所处区域,得出其边界开关状态,再引入修正参数K对边界开关状态进行修正,以此提高策略的快速性并完成共模电压抑制。仿真和实验结果表明该策略实现简单,可以将级联H桥多电平变换器共模电压抑制在最小变化范围内。

基于SVPWM调制策略的T型三电平逆变器研究

针对T型三电平逆变器在新能源发电领域的广泛应用,分析了T型三电平逆变器的结构和工作原理,阐述了空间矢量脉冲宽度调制(SVPWM)策略的思想,详细介绍了参考电压矢量位置判断、基本矢量作用时间计算和基本矢量作用时序生成三个步骤的实现方法.借助Matlab/Simulink软件搭建了基于SVPWM调制策略的T型三电平逆变器的仿真模型,仿真结果验证了仿真模型的正确性和SVPWM调制策略的有效性.

改进蛇算法的七电平逆变器SHEPWM研究

多电平逆变器控制策略中的特定谐波消除脉宽调制(SHEPWM)能够以较低的开关频率得到较好的电压输出波形,重点在于开关角的求取。在多电平逆变器SHEPWM调制的开关角求解算法上提出改进蛇优化算法,对传统蛇优化算法采用Tend混沌映射初始种群,使初始种群分布更加均匀;引入Levy飞行策略增强算法的全局搜素能力,能够更加精准快速得到全局开关角的最优解。仿真结果表明,改进蛇优化算法所求的开关角相较于传统算法更好地消除低次谐波,并降低了输出线电压的畸变率,充分验证了该方法的可行性。

基于SHEPWM的三电平三相逆变器中点电位主动平衡控制策略

在大功率系统中,常采用特定次谐波消除脉宽调制(SHEPWM)以降低系统的开关损耗。针对三电平中点钳位(NPC)型三相逆变器在SHEPWM下的中点电位偏移问题,分析SHEPWM下逆变器输出相电压基波与3次谐波在不同电压相位范围内对中点电位的影响,设计两种在基波周期内对中点电位总充放电效果相反的开关角组合方案,并提出一种通过测量中点电位偏移值及中点电位滞环控制,选择不同的开关角组合方案进行调制的中点电位主动平衡控制策略。实验结果验证了所提出方法的实用性及有效性。

电磁阀异步启闭的PWM喷雾系统设计与试验

PWM变量喷雾是国内外精准农业领域的研究热点,但PWM变量喷雾过程中电磁阀的快速启闭在管路内易形成压力脉冲,致使喷头喷雾压力发生变化,导致喷雾质量下降。为了降低压力脉冲,设计了一种相邻电磁阀异步启闭的PWM喷雾系统,由移动底盘、药箱、隔膜泵、稳压罐、PWM控制器、电磁阀及压力表等组成,通过延时控制,实现电磁阀异步启闭。在室内无风环境条件下,探究了喷雾系统电磁阀前管路内压力波动特性和沉积量分布均匀性。试验表明:与电磁阀同步启闭的PWM喷雾系统相比,电磁阀异步启闭可有效降低管路内压力峰值,不同PWM频率工况条件下,50%占空比时降幅最大,降幅最高为14%;20Hz频率条件下,异步启闭PWM喷雾的沉积量分布均匀性变异系数略高于常规连续喷雾,但均小于15%。上述结果符合喷杆喷雾机技术性能国家标准。