THEORY AND EXPERIMENTAL STUDY OF THE SELF-EXCITED OSCILLATION PULSED JET NOZZLE

Comparing with usual continuous jet nozzle, the self-excited oscillationpulsed jet nozzle SEOPJN) can make jet generate a higher peak of pressure and larger scouringvolume. And it can make jet increase the effective standoff distance, too. The basic theories of theSEOPJN are introduced. Some experimental results are shown. According to the results, using tricornbits assembled the SEOPJN to drill oil well, the ROP increases by 8 percent approx 77 percent, andthe rates of the footage for tricorn bit increases by 6.7 percent approx 44.0 percent.

HYDRODYNAMIC ANALYSIS OF SUCK-IN PULSED JET IN WELL DRILLING

The development of new drilling methods is important for the exploration and production of oil fields.The pulsed jet is a drilling technology of high potentiality.This article proposes a new concept of suck-in pulsed jet with self-excited oscillation,by which a full use of the hydraulic power can be made in the annular space.A hydrodynamic analysis of suck-in pulsed jet with self-excited oscillation is carried out by numerical simulations and rock-breaking experiments.It is shown that with the jet,a negative pressure zone will be formed in the oscillation cavity to ensure automatic sucking of enough annular fluids and the formation of an efficient pulsed jet.The rock-breaking and pressure testing results have verified the reliability of the numerical simulation.The research provides a basis for the development of the pulsed jet drilling technology.

Relations between pulsed jet noise and steady jet noise

On the hypothesis that the turbulent flow is practically not affected in character by pulsation of the flow, the formula for sound pressure level of pulsed jet noise is obtained in 90 °direction and 1 meter away from the nozzle. The steady jet noise is , then, a special case when the pulsating frequency is zero. The results agree well with experiments.

Dynamic effects of high-pressure pulsed water jet in low-permeability coal seams

Mine gas extraction in China is difficult due to the characteristics such as micro-porosity,low-permeability and high adsorption of coal seams.The pulsed mechanismof a high-pressure pulsed water jet was studied through theoretical analysis,experimentand field measurement.The results show that high-pressure pulsed water jet has threedynamic properties.What's more,the three dynamic effects can be found in low-permeabilitycoal seams.A new pulsed water jet with 200-1 000 Hz oscillation frequency andpeak pressure 2.5 times than average pressure was introduced.During bubble collapsing,sound vibration and instantaneous high pressures over 100 MPa enhanced the cuttingability of the high-pressure jet.Through high-pressure pulsed water jet drilling and slotting,the exposure area of coal bodies was greatly enlarged and pressure of the coal seamsrapidly decreased.Therefore,the permeability of coal seams was improved and gas absorptionrate also decreased.Application results show that gas adsorption rate decreasedby 30%-40%and the penetrability coefficient increased 100 times.This proves that high-pressurepulsed water is more efficient than other conventional methods.

Formation Principle and Characteristics of Self‑Supercharging Pulsed Water Jet

High-pressure pulsed water jet technology has considerable development potential in the field of rock fragmentation.To overcome the shortcomings of existing pulsed jets,a self-supercharging pulsed water jet(SSPWJ)generation method is proposed,which is based on the theory of the pulsed water jet and the principle of hydraulic boosting.The proposed method changes the flow direction of the fluid medium through the valve core to make the piston reciprocate in the cylinder and relies on the effective area difference between the front and rear chambers in the stroke stage of the piston to realize the organic combination of“pulse”and“supercharging”of the jet,thus forming an SSPWJ.On the basis of the formation principle of the SSPWJ,a SSPWJ testing platform was constructed,and tests were performed on the jet pressure acquisition,morphology capture,and granite erosion.Both the jet pressure and the jet morphology exhibited periodic changes,and a higher pulse pressure was obtained at lower inlet pressure.The error of the pressure ratio calculated according to the experimental results was<3%relative to the theoretical design value,confirming the feasibility of the method.The pulse pressure and pulse frequency are controllable;that is,as the inlet flow rate increases in the stroke stage of the piston,the pulse pressure and pulse frequency increase,and the pulse duration decreases.As the inlet flow rate increases in the backward-stroke stage of the piston,the pulse frequency increases,and the pulse pressure and pulse duration remain unchanged.Under the combined action of the waterhammer pressure,high-speed lateral flow,and high-frequency dynamic load of the SSPWJ,local flaky exfoliation was observed when the granite surface was eroded.The results of this study lay the foundation for enriching the theory of pulsed jet generation and expanding its application range.

Study of the expansion characteristics of a pulsed plasma jet in air

In the background of electrothermal-chemical （ETC） emission,an investigation has been conducted on the characteristics of a freely expanding pulsed plasma jet in air.The evolutionary process of the plasma jet is experimentally investigated using a piezoelectric pressure sensor and a digital high-speed video system.The variation relation in the extended volume,axial displacement and radial displacement of the pulsed plasma jet in atmosphere with time under different discharge voltages and jet breaking pressures is obtained.Based on experiments,a two-dimensional axisymmetric unsteady model is established to analyze the characteristics of the two-phase interface and the variation of flow-field parameters resulting from a pulsed plasma jet into air at a pressure of 1.5-3.5 MPa under three nozzle diameters （3 mm,4 mm and 5 ram,respectively）.The images of the plasma jet reveal a changing shape process,from a quasiellipsoid to a conical head and an elongated cylindrical tail.The axial displacement of the jet is always larger than that along the radial direction.The extended volume reveals a single peak distribution with time.Compared to the experiment,the numerical simulation agrees well with the experimental data.The parameters of the jet field mutate at the nozzle exit with a decrease in the parameter pulse near the nozzle,and become more and more gradual and close to environmental parameters.Increasing the injection pressure and nozzle diameter can increase the parameters of the flow field such as the expansion volume of the pulsed plasma jet,the size of the Mach disk and the pressure.In addition,the turbulent mixing in the expansion process is also enhanced.

Microstructure and properties of nanocrystalline nickel coatings prepared by pulse jet electrodeposition

The fabrication of nanocrystalline nickel coatings was conducted by pulse jet electrodeposition on the substrate of 45# carbon steel.The effects of average current density on the surface morphology,microstructure,average grain size and microhardness of nickel coatings were investigated by scanning electron microscopy(SEM),X-ray diffractometry(XRD)and microhardness measurement.In addition,the corrosion resistances of coating and substrate were compared.It is revealed that the nickel coatings prepared by pulse jet electrodeposition exhibit a fine-grained structure with a smooth surface and a high density,although some pores and defects are still present in coatings.With the increase of average current density,the average grain size of nickel coatings is reduced at first and then increased.The coating with the optimum compactness,the smallest average grain size(13.7 nm)and the highest microhardness are obtained at current density of 39.8 A/dm2.The corrosion resistance is obviously increased for the coatings prepared by pulse jet electrodeposition;however,the corrosion rate is increased after a certain period due to the penetration of the corrosive media.

Properties and testing of a hydraulic pulse jet and its application in offshore drilling

Offshore drilling has attracted more attention than ever before due to the increasing worldwide energy demand especially in China. High cost, long drilling cycles, and low rate of penetration （ROP） represent critical challenges for offshore drilling operations. The hydraulic pulse generator was specifically designed, based on China offshore drilling technologies and parameters, to overcome problems encountered during offshore drilling. Both laboratory and field tests were conducted to collect the characteristics of the hydraulic pulse generator. The relationships between flow rate and pressure amplitude, pressure loss and pulse frequency were obtained, which can be used to optimize operation parameters for hydraulic pulse jet drilling. Meanwhile a bottom hole assembly （BHA） for pulse jet drilling has been designed, combining the hydraulic pulse generator with the conventional BHA, positive displacement motor, and rotary steerable system （RSS） etc. Furthermore, the hydraulic pulse jet technique has been successfully applied in more than 10 offshore wells in China. The depth of the applied wells ranged from 2,000 m to 4,100 m with drilling bit diameters of 311 mm and 216 mm. The field application results showed that hydraulic pulse jet technique was feasible for various bit types and formations, and that ROP could be significantly increased, by more than 25%.

Deposition of SiCxHyOz thin film on epoxy resin by nanosecond pulsed APPJ for improving the surface insulating performance

Non-thermal plasma surface modification for epoxy resin（EP）to improve the insulation properties has wide application prospects in gas insulated switchgear and gas insulatedtransmission line.In this paper,a pulsed Ar dual dielectrics atmospheric-pressure plasma jet（APPJ）was used for Si CxHyOzthin film deposition on EP samples.The film deposition was optimized by varying the treatment time while other parameters were kept at constants（treatment distance：10 mm,precursor flow rate：0.6 l min-（-1）,maximum instantaneous power：3.08 k W and single pulse energy：0.18 m J）.It was found that the maximum value of flashover voltages for negative and positive voltage were improved by 18%and 13%when the deposition time was3 min,respectively.The flashover voltage reduced as treatment time increased.Moreover,all the surface conductivity,surface charge dissipation rate and surface trap level distribution reached an optimal value when thin film deposition time was 3 min.Other measurements,such as atomic force microscopy and scanning electron microscope for EP surface morphology,Fourier transform infrared spectroscopy and x-ray photoelectron spectroscopy for EP surface compositions,optical emission spectra for APPJ deposition process were carried out to better understand the deposition processes and mechanisms.The results indicated that the original organic groups（C–H,C–C,C=O,C=C）were gradually replaced by the Si containing inorganic groups（Si–O–Si and Si–OH）.The reduction of C=O in ester group and C=C in p-substituted benzene of the EP samples might be responsible for shallowing the trap level and then enhancing the flashover voltage.However,when the plasma treatment time was longer than 3 min,the significant increase of the surface roughness might increase the trap level depth and then deteriorate the flashover performance.

Mixing Characteristics of Pulsed Air-assist Liquid Jet into an Internal Subsonic Cross-flow

Penetration depth,spray dispersion angle,droplet sizes in breakup processes and atomization processes are very important parameters in combustor of air-breathing engine.These processes will enhance air/fuel mixing inside the combustor.Experimental results from the pulsed air-assist liquid jet injected into a cross-flow are investigated.And experiments were conducted to a range of cross-flow velocities from 42～136 m/s.Air is injected with 0～300kPa,with air-assist pulsation frequency of 0～20Hz.Pulsation frequency was modulated by solenoid valve.Phase Doppler Particle Analyzer(PDPA) was utilized to quantitatively measuring droplet characteristics.High-speed CCD camera was used to obtain injected spray structure.Pulsed air-assist liquid jet will offer rapid mixing and good liquid jet penetration.Air-assist makes a very fine droplet which generated mist-like spray.Pulsed air-assist liquid jet will introduce additional supplementary turbulent mixing and control of penetration depth into a cross-flow field.The results show that pulsation frequency has an effect on penetration,transverse velocities and droplet sizes.The experimental data generated in these studies are used for a development of active control strategies to optimize the liquid jet penetration in subsonic cross-flow conditions and predict combustion low frequency instability.

Analysis of chamber effect on intermittent pulsation

A numerical study was conducted to seek an optimized dimension of jet chamber in the pulsating impinging flow.The flow and heat transfer effect of the pulsation flow through a jet chamber was investigated.The numerical results indicate that heat transfer effective enhances near the stagnation region for the intermittent pulsed flow with jet chamber compared to that without jet chamber.Simulations of the flow through a jet chamber show that the heat transfer rate on the impingement surface is highly dependent on the velocity at the position which is really close to target surface.Examination of the velocity field suggests that the velocity exists a maximum value as the axis distance increases.In addition,the velocity at the jet hole is enlarged by the jet chamber due to the entrainment effect,and the velocity is amplified even greater as the size of the jet chamber becomes bigger.Nevertheless,the velocity declines quickly while the flow axis distance is more than a certain range,leading to poor heat transfer.Thus,intermittent pulsed flow with jet chamber is suggested as a method of improving heat transfer by employing larger dimensions of jet chamber for appropriate jet-to-surface spacing.

Effect of Exit Geometry of Tail Pipe on the Performance of Pulse Jet Engines

In this paper,the effect of geometries of tube open end on the shock,compression and expansion wavespropagating in the tube was investigated numerically and experimentally.One of them is a conventional straightshock tube with an open end.The other has a divergent tail tube at the exit.Applying a divergent tail tube(flaretube)to an open end shock tube,the period of one-cycle process could be shortened and the pressure behind theexpansion wave produced at the exit of the shock tube could be lowered much more below the atmosphericpressure than that produced in the straight tube.The results suggested that the intake air into the engine wassignificantly increased by applying a flare tube instead of a straight tube.

Effect of Microstructures on Corrosion Behavior of Nickel Coatings:(Ⅰ) Abnormal Grain Size Effect on Corrosion Behavior

Nickel coatings with different microstructures were synthesized by pulse jet electrodeposition technique.Their morphology and microstructure were investigated by scanning electron microscopy（SEM）and transmission electron microscopy（TEM）.The corrosion property of the coatings was studied by using polarization,electrochemical impedance spectroscopy（EIS）,potential of zero free charge（PZFC） measurements and Mott-Schottky（M-S） relationship.The results showed that the coating with grain size of 50 nm possessed higher corrosion resistance than that with grain size of 10 nm.This abnormal behavior may be related to the existence of nanoscale twins in the coatings and the lower concentration of acceptor in the passive films.