A study of pulsed high voltage driven hollow-cathode electron beam sources through synchronous optical trigger

In this study,a pulsed,high voltage driven hollow-cathode electron beam sources through an optical trigger is designed with characteristics of simple structure,low cost,and easy triggering.To validate the new design,the characteristics of hollow-cathode discharge and electron beam characterization under pulsed high voltage drive are studied experimentally and discussed by discharge characteristics and analyses of waveform details,respectively.The validation experiments indicate that the pulsed high voltage supply significantly improves the frequency and stability of the discharge,which provides a new solution for the realization of a high-frequency,high-energy electron beam source.The peak current amplitude in the high-energy electron beam increases from 6.2 A to 79.6 A,which indicates the pulsed power mode significantly improves the electron beam performance.Besides,increasing the capacitance significantly affects the highcurrent,lower-energy electron beam more than the high-energy electron beam.

Improvement of circuit oscillation generated by underwater high voltage pulse discharges based on pulse power thyristor

High voltage fracturing technology was widely used in the field of reservoir reconstruction due to its advantages of being clean, pollution-free, and high-efficiency. However, high-frequency circuit oscillation occurs during the underwater high voltage pulse discharge process, which brings security risks to the stability of the pulse fracturing system. In order to solve this problem, an underwater pulse power discharge system was established, the circuit oscillation generation conditions were analyzed and the circuit oscillation suppression method was proposed. Firstly, the system structure was introduced and the charging model of the energy storage capacitor was established by the state space average method. Next, the electrode high-voltage breakdown model was established through COMSOL software, the electrode breakdown process was analyzed according to the electron density distribution image, and the plasma channel impedance was estimated based on the conductivity simulation results. Then the underwater pulse power discharge process and the circuit oscillation generation condition were analyzed, and the circuit oscillation suppression strategy of using the thyristor to replace the gas spark switch was proposed. Finally, laboratory experiments were carried out to verify the precision of the theoretical model and the suppression effect of circuit oscillation. The experimental results show that the voltage variation of the energy storage capacitor, the impedance change of the pulse power discharge process, and the equivalent circuit in each discharge stage were consistent with the theoretical model. The proposed oscillation suppression strategy cannot only prevent the damage caused by circuit oscillation but also reduce the damping oscillation time by77.1%, which can greatly improve the stability of the system. This research has potential application value in the field of underwater pulse power discharge for reservoir reconstruction.

Numerical Study of Pulsed Dielectric Barrier Discharge at Atmospheric Pressure Under the Needle-Plate Electrode Configuration

In this paper, we study the characteristics of atmospheric-pressure pulsed dielectric barrier discharge （DBD） under the needle-plate electrode configuration using a one-dimensional self-consistent fluid model. The results show that, the DBDs driven by positive pulse, negative pulse and bipolar pulse possess different behaviors. Moreover, the two discharges appearing at the rising and the falling phases of per voltage pulse also have different discharge regimes. For the case of the positive pulse, the breakdown field is much lower than that of the negative pulse, and its propagation characteristic is different from the negative pulse DBD. When the DBD is driven by a bipolar pulse voltage, there exists the interaction between the positive and negative pulses, resulting in the decrease of the breakdown field of the negative pulse DBD and causing the change of the discharge behaviors. In addition, the effects of the discharge parameters on the behaviors of pulsed DBD in the needle-plate electrode configuration are also studied.

THE EFFECTS OF PULSE BIAS VOLTAGE AND N_2 PARTIAL PRESSURE ON TiAlN FILMS OF ARC ION PLATING (AIP)

Owing to the characteristics of arc ion plating(AIP) technique, the structure and composition of TiAlN films can be tailored by controlling of various parameters such as compositions of target materials, N2 partial pressure, substrate bias and so on. In this study, several titanium aluminum nitride films were deposited on 1Cr11Ni2W2MoV steel for compressor blade of areo-engine under different d.c pulse bias voltage and nitrogen partial pressure. The effects of substrate pulse bias and nitrogen partial pressure on the deposition rate, droplet formation, microstruture and elemental component of the films were investigated.

Deposition of SiCxHyOz thin film on epoxy resin by nanosecond pulsed APPJ for improving the surface insulating performance

Non-thermal plasma surface modification for epoxy resin（EP）to improve the insulation properties has wide application prospects in gas insulated switchgear and gas insulatedtransmission line.In this paper,a pulsed Ar dual dielectrics atmospheric-pressure plasma jet（APPJ）was used for Si CxHyOzthin film deposition on EP samples.The film deposition was optimized by varying the treatment time while other parameters were kept at constants（treatment distance：10 mm,precursor flow rate：0.6 l min-（-1）,maximum instantaneous power：3.08 k W and single pulse energy：0.18 m J）.It was found that the maximum value of flashover voltages for negative and positive voltage were improved by 18%and 13%when the deposition time was3 min,respectively.The flashover voltage reduced as treatment time increased.Moreover,all the surface conductivity,surface charge dissipation rate and surface trap level distribution reached an optimal value when thin film deposition time was 3 min.Other measurements,such as atomic force microscopy and scanning electron microscope for EP surface morphology,Fourier transform infrared spectroscopy and x-ray photoelectron spectroscopy for EP surface compositions,optical emission spectra for APPJ deposition process were carried out to better understand the deposition processes and mechanisms.The results indicated that the original organic groups（C–H,C–C,C=O,C=C）were gradually replaced by the Si containing inorganic groups（Si–O–Si and Si–OH）.The reduction of C=O in ester group and C=C in p-substituted benzene of the EP samples might be responsible for shallowing the trap level and then enhancing the flashover voltage.However,when the plasma treatment time was longer than 3 min,the significant increase of the surface roughness might increase the trap level depth and then deteriorate the flashover performance.

Dispersion effect on the current voltage characteristic of AlGaN/GaN high electron mobility transistors

The current voltage （IV） characteristics are greatly influenced by the dispersion effects in A1GaN/CaN high electron mobility transistors. The direct current （DC） IV and pulsed IV measurements are performed to give a deep investigation into the dispersion effects, which are mainly related to the trap and self-heating mechanisms. The results show that traps play an important role in the kink effects, and high stress can introduce more traps and defects in the device. With the help of the pulsed IV measurements, the trapping effects and self-heating effects can be separated. The impact of time constants on the dispersion effects is also discussed. In order to achieve an accurate static DC IV measurement, the steady state of the bias points must be considered carefully to avoid the dispersion effects.

Ignition dynamics of radio frequency discharge in atmospheric pressure cascade glow discharge

A cascade glow discharge in atmospheric helium was excited by a microsecond voltage pulse and a pulse-modulated radio frequency(RF) voltage, in which the discharge ignition dynamics of the RF discharge burst was investigated experimentally. The spatio-temporal evolution of the discharge, the ignition time and optical emission intensities of plasma species of the RF discharge burst were investigated under different time intervals between the pulsed voltage and RF voltage in the experiment. The results show that by increasing the time interval between the pulsed discharge and RF discharge burst from 5 μs to 20 μs, the ignition time of the RF discharge burst is increased from 1.6 μs to 2.0 μs, and the discharge spatial profile of RF discharge in the ignition phase changes from a double-hump shape to a bell-shape. The light emission intensity at 706 nm and 777 nm at different time intervals indicates that the RF discharge burst ignition of the depends on the number of residual plasma species generated in the pulsed discharges.

Influence of the low voltage pulsed magnetic field on the columnar-to-equiaxed transition during directional solidification of superalloy K4169

The low voltage pulsed magnetic field(LVPMF)disrupts the columnar dendrite growth,and the columnarto-equiaxed transition(CET)occurs during the directional solidification of superalloy K4169.Within the pulse voltage ranging from 100Vto 200 V,a transition from columnar to equiaxed grain was observed,and the grain size decreased as the pulse voltage rised.As the pulse frequency increased,the CET occurred,and the grains were refined.However,the grains became coarse,and the solidification structure was columnar crystal again when frequency increased to 10 Hz.The LVPMF had an optimal frequency to promote CET.The LVPMF on the CET was affected by the withdrawal speed and increasing the withdrawal speed enhances the CET.The distribution of electromagnetic force and flow field in the melt under the LVPMF were modeled and simulated to reveal the CET mechanism.It is considered that the CET should be attributed to the coupling effects of magnetic vibration and melt convection induced by the LVPMF.

An Active Triggered Surge Protective Gap

A triggered surge protective device is designed and its discharge characteristics axe studied. The experimental results show that the triggered surge protective device has excellent surge protective characteristics. When the gap distance is 5 mm, p. d is 90 Pa.mm and without an active energy trigger circuit, the DC breakdown voltage of the triggered surge protective device is 2.32 kV and the pulse breakdown voltage is 5.75 kV. Therefore, the pulse voltage ratio, which is defined as the specific value of pulse breakdown voltage and DC breakdown voltage, is 2.48. With a semiconductor ZnO flashover trigger device and an active energy coupling trigger circuit, the pulse breakdown voltage can be reduced to 3.32 kV, the pulse voltage ratio is 1.43 and the response time is less than 100 ns. These results are helpful in laying a theoretical foundation for further studies on triggered surge protective devices.

Investigation on latch-up susceptibility induced by high-power microwave in complementary metal–oxide–semiconductor inverter

The latch-up effect induced by high-power microwave（HPM） in complementary metal–oxide–semiconductor（CMOS） inverter is investigated in simulation and theory in this paper. The physical mechanisms of excess carrier injection and HPM-induced latch-up are proposed. Analysis on upset characteristic under pulsed wave reveals increasing susceptibility under shorter-width pulsed wave which satisfies experimental data, and the dependence of upset threshold on pulse repetitive frequency（PRF） is believed to be due to the accumulation of excess carriers. Moreover, the trend that HPMinduced latch-up is more likely to happen in shallow-well device is proposed.Finally, the process of self-recovery which is ever-reported in experiment with its correlation with supply voltage and power level is elaborated, and the conclusions are consistent with reported experimental results.

Suppression of persistent photoconductivity in high gain Ga_(2)O_(3) Schottky photodetectors

The defect-related photoconductivity gain and persistent photoconductivity(PPC)observed in Ga_(2)O_(3)Schottky photodetectors lead to a contradiction between high responsivity and fast recovery speed.In this work,a metal-semiconductor-metal(MSM)Schottky photodetector,a unidirectional Schottky photodetector,and a photoconductor were constructed on Ga_(2)O_(3)films.The MSM Schottky devices have high gain(>13)and high responsivity(>2.5 A/W)at 230-250 nm,as well as slow recovery speed caused by PPC.Interestingly,applying a positive pulse voltage to the reverse-biased Ga_(2)O_(3)/Au Schottky junction can effectively suppress the PPC in the photodetector,while maintaining high gain.The mechanisms of gain and PPC do not strictly follow the interface trap trapping holes or the self-trapped holes models,which is attributed to the correlation with ionized oxygen vacancies in the Schottky junction.The positive pulse voltage modulates the width of the Schottky junction to help quickly neutralize electrons and ionized oxygen vacancies.The realization of suppression PPC functions and the establishment of physical models will facilitate the realization of high responsivity and fast response Schottky devices.

The Degradation of Organic Pollutants by Bubble Discharge in Water

Organic pollutants could be degraded by using bubble discharge in water with gas aeration in the discharge reactor and more plasma can be generated in the discharge process. When pulsed high voltage was applied between electrodes with gas aerated into the reactor, it showed that bubbles were broken, which meant that breakdown took place. It could also be observed that the removal rate of phenol increased with increasing discharge voltage or pulse frequency, and with reducing initial phenol concentration or solution electric conductivity. It could remove more amount of phenol by oxygen aeration. With increasing oxygen flow rate, the removal rate increased. There was little difference with air or nitrogen aeration for phenol removal. The solution temperature after discharge increased to a great extent. However, this part of energy consumption did not contribute to the reaction, which led to a reduction in the energy utilization efficiency.

High-brightness organic light-emitting diodes

The research of high-brightness organic light-emitting diodes, as an important branch of organic light-emitting diodes （OLEDs）, makes it possible for achieving high-brightness lighting source and lasing. Heat dissipation and efficiency roll off, as two main factors, affect the brightness of the OLEDs heavily. In this paper, high-brightness OLEDs are obtained by utilizing pulse voltage, small areas and micro-cavity structure to minimize the effect of the two factors. The major advances, ongoing challenges and future perspectives of this research frontier are also critically discussed.

Degradation of Acid Orange 7 Dye in Two Hybrid Plasma Discharge Reactors

To get an optimized pulsed electrical plasma discharge reactor and to increase the energy utilization efficiency in the removal of pollutants, two hybrid plasma discharge reactors were designed and optimized. The reactors were compared via the discharge characteristics, energy transfer efficiency, the yields of the active species and the energy utilization in dye wastewater degradation. The results showed that under the same AC input power, the characteristics of the discharge waveform of the point-to-plate reactor were better. Under the same AC input power, the two reactors both had almost the same peak voltage of 22 kV. The peak current of the point-to-plate reactor was 146 A, while that of the wire-to-cylinder reactor was only 48.8 A. The peak powers of the point-to-plate reactor and the wire-to-cylinder reactor were 1.38 MW and 1.01 MW, respectively. The energy per pulse of the point-to-plate reactor was 0.2221 J, which was about 29.4% higher than that of the wire-to-cylinder reactor （0.1716 J）. To remove 50% Acid Orange 7 （AO7）, the energy utilizations of the point-to-plate reactor and the wire- to-cylinder reactor were 1.02×10^-9 mol/L and 0.61×10^-9 mol/L, respectively. In the point-to- plate reactor, the concentration of hydrogen peroxide in pure water was 3.6 mmol/L after 40 min of discharge, which was higher than that of the wire-to-cylinder reactor （2.5 mmol/L）. The concentration of liquid phase ozone in the point-to-plate reactor （5.7×10^-2 mmol/L） was about 26.7% higher than that in the wire-to-cylinder reactor （4.5×10^-2 mmol/L）. The analysis results of the variance showed that the type of reactor and reaction time had significant impacts on the yields of the hydrogen peroxide and ozone. The main degradation intermediates of AO7 identified by gas chromatography and mass spectrometry （GCMS） were acetic acid, maleic anhydride, p- benzoquinone, phenol, benzoic acid, phthalic anhydride, coumarin and 2-naphthol. Proposed degradation pathways were elucidated in light of the analyzed degradation products.

The non-destructive threshold of the graphite surface by STM in the ultra-fast pulse mode

In this paper single ultra-fast voltage pulses are introduced to the Pt/Ir tip of a scanning tunnelling microscope （STM）, and the non-destructive threshold of the graphite surface is studied systematically in a wide range of pulse durations （from 104 to 8 ns）. Considering the waveform distortion of the pulses at the tunnelling region, this paper gives the corrected threshold curve of pulse amplitude depending on pulse duration. A new explanation of threshold power has been suggested and fits the experimental results well.

A Control System Design to Establish Dose-Response Relationships in Wound Healing Therapy

Advanced biophysical wound healing therapies can apply mechanical, electrical, or light energy to re-stimulate healing processes in chronic wounds. Despite the growing evidence of the clinical efficacy of these therapies, the optimal treatment stimulation parameters remain unknown and there are no standard treatment protocols. We introduce a closed-loop control design as an experimental system to study the dose-response of wound healing therapy treatment within a prescribed multidimensional and multimodal stimulation parameter space. Systems engineering approaches are applied to the control problem for estimation of a transfer function and model equations derived for use in optimal model-based control. The experimental control system design consisted of simultaneous application of biophysical energies inputted into a wound system. A study design set up including the use of negative pressure wound therapy, electrical stimulation therapy, and photobiomodulation device systems was described. Treatment stimulation parameters were selected from experimental ranges used in the scientific literature. Classical control methods and model-based control were suggested for model selection and evaluation and design of the overall control system. An experimental design for multimodal biophysical wound healing therapy control system is introduced to establish the dose-response interactions for development of therapeutic applications and device design.

Formation of diffuse and spark discharges between two needle electrodes with the scattering of particles

The development of a nanosecond discharge in a pin-to-pin gap filled with air at atmospheric pressure has been studied with high temporal and spatial resolutions from a breakdown start to the spark decay.Positive and negative nanosecond voltage pulses with an amplitude of tens of kilovolts were applied.Time-resolved images of the discharge development were taken with a fourchannel Intensified Charge Coupled Device(ICCD)camera.The minimum delay between the camera channels could be as short as≈0.1 ns.This made it possible to study the gap breakdown process with subnanosecond resolution.It was observed that a wide-diameter streamer develops from the high-voltage pointed electrode.The ionization processes near the grounded pin electrode started when the streamer crossed half of the gap.After bridging the gap by the streamer,a diffuse discharge was formed.The development of spark leaders from bright spots on the surface of the pointed electrodes was observed at the next stage.It was found that the rate of development of the spark leader is an order of magnitude lower than that of the wide-diameter streamer.Long thin luminous tracks were observed against the background of a discharge plasma glow.It has been established that the tracks are adjacent to brightly glowing spots on the electrodes and are associated with the flight of small particles.

Machining of circular micro holes by electrochemical micro-machining process

Machining of micro holes with micro electro- chemical machining （micro ECM） process has been carried out with an indigenously developed set up. This paper describes relevant problems and solutions for the circular micro holes machining process on 304 stainless steel sheets with 60 μm thickness using high speed steel cylindrical tool of diameter 500 ~tm and using dilute I-I2SO4 as elec- trolyte. The taper angle variation of the machined hole is analyzed and reported for different experimental setting parameters. The minimum value of the taper angle of machined holes is achieved at the parameter setting of 0.4 mol/L H2504, 700 kHz, 600 ns and 21 V, for stainless steel sheets and HSS tool.