Simulation of Underground Reservoir Stability of Pumped Storage Power Station Based on Fluid-Structure Coupling

Based on global initiatives such as the clean energy transition and the development of renewable energy,the pumped storage power station has become a new and significant way of energy storage and regulation,and its construction environment is more complex than that of a traditional reservoir.In particular,the stability of the rock strata in the underground reservoirs is affected by the seepage pressure and rock stress,which presents some challenges in achieving engineering safety and stability.Using the advantages of the numerical simulation method in dealing deal with nonlinear problems in engineering stability,in this study,the stability of the underground reservoir of the Shidangshan(SDS)pumped storage power station was numerically calculated and quantitatively analyzed based on fluid-structure coupling theory,providing an important reference for the safe operation and management of the underground reservoir.First,using the COMSOL software,a suitablemechanicalmodel was created in accordance with the geological structure and project characteristics of the underground reservoir.Next,the characteristics of the stress field,displacement field,and seepage field after excavation of the underground reservoir were simulated in light of the seepage effect of groundwater on the nearby rock of the underground reservoir.Finally,based on the construction specifications and Molar-Coulomb criterion,a thorough evaluation of the stability of the underground reservoir was performed through simulation of the filling and discharge conditions and anti-seepage strengthening measures.The findings demonstrate that the numerical simulation results have a certain level of reliability and are in accordance with the stress measured in the project area.The underground reservoir excavation resulted in a maximum displacement value of the rock mass around the caverns of 3.56 mm in a typical section,and the safety coefficient of the parts,as determined using the Molar-Coulomb criterion,was higher than 1,indicating that the project as a whole is in a stable state.

Hydraulic fluctuations during the pump power-off runaway transient process of a pump turbine with consideration of cavitation effects

A runaway transition after the pump power interruption and the simultaneous guide vane servomotor failure is one of the most dangerous and complex transitions for a pumped storage power system(PSPS).This paper analyzes the fluctuation behavior and mechanism of a PSPS during a runaway transition caused by the pump power interruption.The transient cavitation flow in the PSPS is simulated by using a one-dimensional and three-dimensional coupling flow simulation method for the runaway transition.Subsequently,the effects of the transient fluctuation of the radial hydraulic thrust on the runner and transient pressures are analyzed using the short-time Fourier transform method.Finally,the mechanisms are analyzed based on the analysis of the internal flow field.This study suggests that the extreme fluctuation generally occurs near the critical transformation points between the two operation modes.In addition,the extreme fluctuation behavior is primarily related to the local backflow near the runner inlet and the unstable cavitation phenomena in the runner and the draft tube.This finding helps for optimizing the runner design to resolve the instability problems of a PSPS.

Low pump power co-fiber remotely pumped EDFA used in DWDM systems with ultra-long fiber span

In this paper, aiming at practical dense wavelength division multiplexing （DWDM） system with ultralong fiber span, a simple co-fiber remotely pumped erbium-doped fiber amplifier （RP-EDFA） scheme is proposed to extend span distance with simple configuration and low pump power. Equivalent noise figure of -6 dB is achieved under 300-mW pump power. Using the experiment results, numerical simulation of ultra-long span systems shows that for a 40 × 11.6-Gb/s transmission system, the RP-EDFA scheme can support transmission of 1760 km with a fiber span of 160 km. These results demonstrate the potential of the PR-EDFA scheme in ultra-long span transmission.

Investigation of ellipticity and pump power in a passively mode-locked fiber laser using the nonlinear polarization rotation technique

An elliptical initial polarization state is essential for generating mode-locked pulses using the nonlinear polarization rotation technique. In this work, the relationship between the ellipticity ranges capable of maintaining mode-locked operation against different pump power levels is investigated. An increasing pump power, in conjunction with minor adjustments to the polarization controller＇s quarter waveplate, results in a wider ellipticity range that can accommodate mode-locked operation. Other parameters such as noise, pulsewidth, and average output power are also observed to vary as the ellipticity changes.

Optimized Pump Power Ratio on 2nd Order Pumping Discrete Raman Amplifier

By optimizing pump power ratio between 1st order backward pump and 2nd order forward pump on discrete Raman amplifier, we demonstrated over 2dB noise figure improvement without excessive non-linearity degradation.

Analytical Expression of the Threshold Pump Power of Erbium－doped Fiber Lasers Pumped at 980nm and 1480nm Wavelengths

The rate equations,which is suitable to erbium-doped fiber lasers pumped at 980 nm and 1 480nm wavelengths respectively,are investigated,and analytical expressions of the threshold pump powers under two pump wavelengths are derived.As a result,some important parameters can be quantitatively specified.

Study on integrated development and hybrid operation mode of nuclear power plant and pumped-storage power station

The nuclear power plant is suitable for base-load operation, while the pumped-storage unit mainly gives play to capacity benefit in the electric power system;hence, the integrated development and hybrid operation mode of the two can better meet the needs of the electric power system. This article first presents an analysis of the necessity and superiority of such mode, then explains its meaning and analyzes the working routes. Finally, it proposes the business modes as follows: low price pumping water electricity plus nuclear power in the near term;nuclear power shifted to pumped storage power participating in market competition in the middle term;and, in the long term, nuclear power shifted to pumped storage power as primary and serving as an electric power system when needed.

Prospect of new pumped-storage power station

In this paper, a new type of pumped-storage power station with faster response speed, wider regulation range, and better stability is proposed. The operational flexible of the traditional pumped-storage power station can be improved with variable-speed pumped-storage tech no logy. Combined with chemical en ergy storage, the failure to achieve sec on d-order response speed and the insufficient safety and reliability of pumped-storage power units could be solved. With the better solar en ergy and site resources, the in teg rated performance can be improved by an optical storage system in stalled in future pumped-storage stations. Through the characteristics analysis of the new type of pumped-storage power station, three types of optimal station locations are proposed, namely, the load concentration area, new energy concentration area, and ultrahigh- voltage direct current receiver area. Taking the new pumped-storage power station as an example, the advantages of multi-energy cooperation and joint operation are analyzed. It can be predicted that the frequency and load regulation of the power grid will be more flexible, and the service capacity to the main power grid will be much stronger in the future.

A novel technology for control of variable speed pumped storage power plant

Variable speed pumped storage machines are used extensively in wind power plant and pumped storage power plant. This paper presents direct torque and flux control(DTFC) of a variable speed pumped storage power plant(VSPSP). By this method both torque and flux have been applied to control the VSPSP. The comparison between VSPSP's control strategies is studied. At the first, a wind turbine with the capacity 2.2 k W and DTFC control strategies simulated then a 250 MW VSPSP is simulated with all of its parts(including electrical, mechanical, hydraulic and its control system) by MATLAB software. In all of simulations, both converters including two-level voltage source converter(2LVSC) and three-level voltage source converter(3LVSC) are applied. The results of applying 2LVSC and 3LVSC are the rapid dynamic responses with better efficiency, reducing the total harmonic distortion(THD) and ripple of rotor torque and flux.

Energy-Transfer Processes of Xe（6p[1/2]0,6p[3/2]2,and 6p[5/2]2） Atoms under the Condition of Ultrahigh Pumped Power

The kinetic processes of Xe(6p[1/2]0, 6p[3/2]2, and 6p[5/2]2) atoms under the focused condition were investigated. The atomic density of the laser prepared state significantly increases. Therefore, the probability of the energy-pooling between two high-lying atoms increases. There are three major types of the energy-pooling collisions. The first type is the energy-pooling ionization. Once the excitation laser is focused, the obvious ionization can be observed from the side window whenever the laser prepared state is 6p[1/2]0, 6p[3/2]2, or 6p[5/2]2 state. Ionization of Xe is attributed to the energy-pooling ionization or a Xe* atom reabsorbing another excitation photon. The second type is energy-pooling with big energy difference. When the 6p[1/2]0 state is the laser prepared state, the energy-pooling collision between two 6p[1/2]0 atoms can produce one 5d[3/2]1 atom and one 6s'[1/2]0 atom. The third type is energy-pooling with small energy difference. The intensities of fluorescence lines are much stronger that five secondary 6p states act as the upper states, and the rising edges of these fluorescence lines are much steeper. The primary mechanism of generating the secondary 6p atoms is energy-pooling collision instead of collision relaxation. Based on the collision probability, the rate of energy-pooling between two 6p[1/2]0 atoms is deduced (6.39x10^8s-1). In addition, the 6s atoms also increase under the focused condition. Therefore, all the fluorescence lines are serious trailing by radiation trapping.

Research on single hole heat transfer power of ground source heat pump system

In this paper,the single hole heat transfer power of the ground source heat pump system in Hengshui is compared with data gained from thermal response test.The results show that maximum monitoring data of heat transfer power per meter in summer is 97.1% of the test data,and the average value accounts for 81.8%.The per meter heat power data through on-site thermal response test can provide references for designing engineering project and optimizing ground source heat pump system as these data do not vary greatly from the actual monitoring data.

STUDY ON POWER SPARE COEFFICIENT OF ELECTRICAL MOTOR IN LARGE PUMP STATION BASED ON RELIABILITY

Characters of head of low head pump station and the pump shaft power areanalyzed. Influence of each single factor on pump shaft power is expressed as change of specificshaft power. (non-dimensional) and the probability density function is determined. Influences ofmultiple factors on pump shaft power are analyzed. Method of calculating none over-loadedprobability of motor by integration by successive reductions is put forward and then relationbetween power spare coefficient and none over-loaded reliability of electric motor is established.Influences of all factors on pump shaft power being considered completely; power spare coefficientsof motor are calculated in three kinds of heads (changing and unchanging), two kinds of dirty-outconditions. Electrical motor power spare coefficients should be chosen as 1.20 approx 1.44, 1.11approx 1.19, 1.09 approx.14 respectively when pump heads are 4, 7, 9.5 m. The results mean much toreasonable choose of electrical motors in large pump stations, increasing reliability of pump unitsand saving equipment investment.

Power Stabilization by Windfarm Applied Statistical Model and Pumped Storage Generation Using Archimedean Screw

In this paper, a method of stabilizing electric power by a system which is a combination of wind power generation and pumped storage power generation is proposed. The system operates based on the output predicted value of the windfarm. When the measured windfarm output is larger than the predicted value, the system is pumping up water with surplus power. When the windfarm output is smaller than the predicted value, the system is filling up lack power by hydro generator. Also, since hydro generator works with a start-up delay time, output shortage occurs at this time. To improve output shortage at the time, we estimate the time below the predicted value by a statistical model. As the result, the system succeeded in stabilizing the power and improving the start-up delay time of the hydro generator.

Optimal Dispatching Model Considering the Pumped Sto-rage Power Plant in Hunan

This paper made a research on the Intelligent Optimization Operating Modeling of Pumped Storage Power Station in Hunan Power Grid. First it introduces the characteristics of Hunan power grid and analysis the practical requirement of dispatching. Then it brings forward the intelligent optimization model and set up running model for pumped storage power station of Hei Mi-feng. At last, it introduces the application of pumped storage power station in Hunan power grid and proves the effectiveness of the optimization models.

Behavioral Variations of Gain and NF Owing to Configurations and Pumping Powers

Six configurations are proposed in this paper to explore the gain and noise figure (NF) variations under the pumping power effect. I propose a new investigation of gain and NF at different EDFA configurations. Configurations such as SPSS, DPSS, DPSSF, TPDS, TPDSF, and QPDSF are designed, investigated and compared. A continuous progress of gain values is observed from SPSS to QPDSF, and a change of NF values related to configurations is recorded. The NF variations show different behaviors at different configurations. High gain of 59.49 dB and low NF value of 4.22 dB are recorded for the QPDSF configuration and low gain and low NF are recorded for the SPSS configuration.

Equivalent Substitution Based Method for Calculation of Best Installed Capacity of Pumped Storage Power Station

This paper proposes a novel method to calculate the best installed capacity of pumped storage power station. First, we choose the day with maximum load as the typical day for every month and simulate the system running in two cases of whether the pumped storage power station is put into operation. The difference of the total coal consumption between the two cases is the peak load shifting benefit. Furthermore, we build load model and power generation model to calculate the benefit of emergency use and frequency modulation, which are the major projects of dynamic benefits. At last, on the premise of ensuring the system requirements, the developed method employs the maximum benefit of the unit capacity as the objective function to get the best installed capacity of pumped storage power station by simulations. Tests on a provincial power grid have shown that the developed method which combines of load characteristics, electric structure and other factors can get the best installed capacity of pumped storage power station easily and has a certain guiding significance for the planning and construction of the pumped storage power station.

High power external-cavity surface-emitting laser with front and end pump

High power optically pumped vertical-external-cavity surface-emitting lasers with front and end pump are re- ported. The gain chip consists of 15 repeats of In0.26GaAs/GaAsP0.02 multiple quantum wells and 30 pairs of Alo.2GaAs/Alo.98GaAs distributed Bragg reflectors. The maximum output power of 3 W, optical-to-optical conversion efficiency of 22.4%, and slope efficiency of 29.8% are obtained with 5-℃ heatsink temperature under the front pump, while the maximum output power of 1.1 W, optical-to-optical conversion efficiency of 23.2%, and slope efficiency of 30.8% are reached with 5-℃ heatsink temperature under the end pump. Influences of thermal effects on the output power of the laser with front and end pump are discussed.

Test Facility for Low Potential Pumped Storage Power Plants and Hydrokinetic Turbines

The electric energy which is generated by wind power plants depends on the wind speed and exceeds with strong permissible wind speed the electric energy requirements of the country. In order not to reduce this electrical energy, it must be stored. The sensible energy storage is currently the pumped storage power plants. As the mountain ranges for conventional pumped storage power plants with drop heights of H 〉 600 m are strictly limited, the development of low potential pumped storage power plants has begun. Increasing the capacity of pumped storage power plants with regard to the wind power plants is urgently needed. In this paper, it is shown using the example of an unneeded port facility, how a port facility can be used after low conversion as a test facility for low potential pumped storage power plants and at the same time for the testing of hydro-kinetic turbines. This type of pump storage power plants does not save the energy due to large drop heights, but primarily due to the large volume flow of water.

Power Stabilization System with Counter-Rotating Type Pump-Turbine Unit for Renewable Energy

Traditional type pumped storage system contributes to adjust the electric power unbalance between day and night, in general. The pump-turbine unit is prepared for the power stabilization system, in this serial research, to provide the constant power with good quality for the grid system, even at the suddenly fluctuating/turbulent output from renewable energies. In the unit, the angular momentum changes through the front impeller/runner must be the same as that through the rear impeller/runner, that is, the axial flow at the outlet should be the same to the axial flow at the inlet. Such flow conditions are advantageous to work at not only the pumping mode but also the turbine mode. This work discusses experimentally the performance of the unit, and verifies that this type unit is very effective to both operating modes.

计及深度调峰的风-光-水-火-抽蓄多能源联网系统优化调度研究

多种能源联网运行逐步成为未来电力系统发展的方向,多能源联网系统的优化调度是应对规模化新能源并网消纳的重要手段。文中建立了计及火电机组深度调峰成本的风-光-水-火-抽蓄联网系统成本模型和考虑调峰主动性的风-光-水-火-抽蓄联网系统日前优化调度模型。针对多能源耦合系统结构复杂的情况,提出了分层优化调度的模型求解策略。上层模型以净负荷波动最小为优化目标,得到等效负荷曲线;下层模型根据上层模型的调度结果,以调峰运行的经济性最优和新能源弃电率最低为目标函数,计及调峰主动性,求解考虑火电机组深度调峰煤耗特性的含新能源系统的经济调度问题。仿真算例表明所建模型实现了多能源联网系统的互补运行,提升了火电机组的深度调峰能力,降低新能源弃电率和系统运行成本。