Continuous wave and active Q-switched operation of Watt-level LED-pumped two-rod Nd,Ce:YAG laser

A high-performance LED-side-pumped two-rod Nd,Ce:YAG laser with continuous-wave(CW) and acousto–optical(A-O) Q-switched operation is demonstrated in this work. A symmetrically shaped flat–flat cavity with two identical LEDside-pumped laser modules is employed for power scalability. In the CW regime, the maximum output average power of laser at 1064 nm is 4.41 W, corresponding to a maximum optical conversion efficiency of 5.3% and a slope efficiency is 12.4%. In the active Q-switched regime, the pulse energy of laser reaches as high as 0.89 m J at a repetition rate of 800 Hz with a pulse width of 457.2 ns, the corresponding highest peak output power is 1.94 k W and the M~2 factor is measured to be about 8.8. To the best of the authors' knowledge, this is the first demonstration and the highest performance of a CW LED-side-pumped two-rod laser Nd,Ce:YAG with Watt-level output reported so far.

Multiphonon-assisted acousto-optical Q-switched laser at 1130 nm in Yb:YCOB crystal

In this Letter,we realized the phonon-assisted Q-switched laser operation in Yb:YCOB crystal.Differing from previous laser wavelengths below 1.1μm,we extended the wavelength to 1130 nm by amplifying multiphonon-assisted electronic transitions.At a repetition rate of 0.1 k Hz,the laser output power was 82 m W with a pulse width of 466.1 ns,corresponding to a high peak power of 1.76 k W and a single pulse energy of 0.82 m J,respectively.To the best of our knowledge,this represents the highest pulse energy among all Yb^(3+)-doped crystal lasers at the wavelength beyond 1.1μm.Such a large pulse energy could be explained by the laser rate-equation theory.These results indicated that the electron-phonon coupling effect not only extends the lasing wavelengths but also enables a fast temporal response to support nanosecond,picosecond,even femtosecond pulse laser operation.

An LED-Side-Pumped Intracavity Frequency-Doubled Nd,Ce:YAG Laser Producing a 2W Q-Switched Red Beam

We report a high-average-power acousto-optic(AO)Q-switched intracavity frequency-doubled red laser based on a high-efficiency light-emitting-diode(LED)pumped two-rod Nd,Ce:YAG laser module.Under quasi-continuous wave operation conditions,a maximum output power of 1319.08 nm wavelength was achieved at 11.26 W at a repetition rate of 100 Hz.

A Laser-Diode-Pumped Nd:YAG Laser Q-Switched with a YAG Color Center Chip

A laser-diode-pumped Nd: YAG laser Q-switched Passively with a YAG colorcenter chip has been deveolped. The Q-switched pulse output has a duration of 25-70ns,an energy of about 7.9 μJ and a repetition frequency of 1.25-5.0kHz when the laser cavityparameters and pump power are changed. The Q-switched dynamics is analyzed with therate equation theorry. The theoretical and experimental results agree well.

Passive Q-Switching in a Flash-Lamp Pumped Nd∶YAG Laser with Ion-Implanted GaAs Wafer

A passive Q-switched flash-lamp-pumped Nd∶YAG laser with the ion-implanted semi-insulating GaAs wafer is reported.The wafer is implanted with 400keV As+ ions in the concentration of 10 16cm -2.Using GaAs wafer as an absorber and an output coupler,62ns pulse duration of single pulse is obtained.

1.5-MHz repetition rate passively Q-switched Nd:YVO4 laser based on WS2 saturable absorber

A transmission-type tungsten disulfide（WS_2）-based saturable absorber（SA） is fabricated and applied to passively Q-switched Nd：YVO_4 laser.The WS_2 nanosheets are deposited on a quartz substrate by the vertical evaporation method.By inserting the WS2 SA into the plano-concave laser cavity,we achieve 153-ns pulses with an average output power of1.19 W at 1064 nm.To the best of our knowledge,both of them are the best results among those obtained by the Q-switched solid-state lasers with WS_2-based absorbers.The repetition rate ranges from 1.176 MHz to 1.578 MHz.As far as we know,it is the first time that MHz level Q-switched pulses have been generated in all solid state lasers based on low-dimensional materials so far.

A compact graphene Q-switched erbium-doped fiber laser using optical circulator and tunable fiber Bragg grating

We demonstrate a passively Q-switched tunable erbium-doped fiber laser （EDFL） based on graphene as a saturable absorber （SA）. A three-port optical circulator （OC） and a strain-induced tunable fiber Bragg grating （TFBG） are used as the two end mirrors in an all-fiber linear cavity. The Q-switched EDFL has a low pump threshold of 23.8 mW. The pulse repetition rate of the fiber laser can be widely changed from 9.3 kHz to 69.7 kHz by increasing the pump power from 23.8 mW to 219.9 mW. The minimum pulse duration is 1.7 p.s and the highest pulse energy is 25.4 nJ. The emission wavelength of the laser can be tuned from 1560.43 nm to 1566.27 nm by changing the central wavelength of the straininduced TFBG.

MoS_2 saturable absorber prepared by chemical vapor deposition method for nonlinear control in Q-switching fiber laser

Due to the remarkable carrier mobility and nonlinear characteristic, MoS2 is considered to be a powerful competitor as an effective optical modulated material in fiber lasers. In this paper, the MoS2 films are prepared by the chemical vapor deposition method to guarantee the high quality of the crystal lattice and uniform thickness. The transfer of the films to microfiber and the operation of gold plated films ensure there is no heat-resistant damage and anti-oxidation. The modulation depth of the prepared integrated microfiber-MoS2 saturable absorber is 11.07%. When the microfiber-MoS2 saturable absorber is used as a light modulator in the Q-switching fiber laser, the stable pulse train with a pulse duration of 888 ns at 1530.9 nm is obtained. The ultimate output power and pulse energy of output pulses are 18.8 mW and 88 nJ, respectively. The signal-to-noise ratio up to 60 dB indicates the good stability of the laser. This work demonstrates that the MoS2 saturable absorber prepared by the chemical vapor deposition method can serve as an effective nonlinear control device for the Q-switching fiber laser.

Q-Switched Raman Fiber Laser with Molybdenum Disulfide-Based Passive Saturable Absorber

We demonstrate a Q-switched Raman fiber laser using molybdenum disulfide （MoS2） as a saturable absorber （SA）. The SA is assembled by depositing a mechanically exfoliated MoS2 onto a fiber ferrule facet before it is matched with another clean ferrule via a connector. It is inserted in a Raman fiber laser cavity with a total cavity length of about 8kin to generate a Q-switching pulse train operating at 1560.2nm. A 7.7-kin-long dispersion compensating fiber with 584 ps.nm-i km-1 of dispersion is used as a nonlinear gain medium. As the pump power is increased from 395 m W to 422 m W, the repetition rate of the Q-switching pulses can be increased from 132.7 to 137.4 kHz while the pulse width is concurrently decreased from 3.35μs to 3.03μs. The maximum pulse energy of 54.3 nJ is obtained at the maximum pump power of 422 roW. These results show that the mechanically exfoliated MoS2 SA has a great potential to be used for pulse generation in Raman fiber laser systems.

Passively Q-Switched Nd,Cr:YAG Laser Simultaneous Dual-Wavelength Operation at 946 nm and 1.3μm

A diode-end-pumped Q-switched high-efficiency Nd, Cr：YAG laser with simultaneous dual-wavelength emission at 946nm and 1.3μm is demonstrated. The maximum output power of 1.93 W with simultaneous dual-wavelength operation is achieved at an absorbed pump power of 13.32 W and an absorbed slope efficiency of 15.15%. The maximum optical-optical efficiency is 14.49% with pulse widths of 16.38ns at 946nm and 26.65ns at 1.3μm. A maximum total repetition rate of 43.25 kHz is obtained.

Q-Switched Ytterbium-Doped Fiber Laser Using Black Phosphorus as Saturable Absorber

We demonstrate a Q-switched ytterbium-doped fiber laser （YDFL） using a newly developed multi-layer black phosphorous （BP） saturable absorber （SA）. The BP SA is prepared by mechanically exfoliating a BP crystal and sticking the acquired BP flakes onto a scotch tape. A small piece of the tape is then placed between two ferrules and incorporated in a YDFL cavity to achieve a stable Q-switched operation in a 1.0 μm region. The laser has a pump threshold of 55.1 mW, a pulse repetition rate that is tunable from 8.2 to 32.9 kHz, and the narrowest pulse width of 10.8 μs. The highest pulse energy of 328 nJ is achieved at the pump power of 97.6 mW. Our results show that multi-layer BP is a promising SA for Q-switching laser operation.

Erbium-Doped Zirconia-Alumina Silica Glass-Based Fiber as a Saturable Absorber for High Repetition Rate Q-Switched All-Fiber Laser Generation

We propose and demonstrate a Q-switched erbium-doped fiber laser （EDFL） using an erbium-doped zirconia-alumina silica glass-based fiber （Zr-EDF） as a saturable absorber. As a 16-cm-long Zr-EDF is incorporated into a ring EDFL cavity, a stable Q-switching pulse train operating at 1565？nm wavelength is successfully obtained. The repetition rate is tunable from 33.97？kHz to 71.23？kHz by increasing the pump power from the threshold of 26？mW to the maximum of 74？mW. The highest pulse energy of 26.67？nJ is obtained at the maximum pump power.

Q-Switched Erbium-Doped Fiber Laser Using Cadmium Selenide Coated onto Side-Polished D-Shape Fiber as Saturable Absorber

A stable Q-switched erbium doped fiber laser emitting at 1558 nm is demonstrated using a cadmium selenide（CdSe） material coated onto a side-polished D-shape fiber as the saturable absorber（SA）. By elevating the input pump power from the threshold of 91 mW to the maximum available power of 136 mW, a pulse train with a maximum repetition rate of 57.44 kHz, minimum pulse width of 3.76 us, maximum average output power of7.99 mW, maximum pulse energy of 0.1391 uJ, and maximum peak power of 36.99 mW are obtained. The signalto-noise ratio of the spectrum is measured to be around 75 dB. This CdSe based SA is simple, robust, and reliable,and thus suitable for making a portable pulse laser source.

Widely Tunable Middle Infrared Optical Parametric Oscillator Pumped by the Q-Switched Ho：GdVO_4 Laser

We demonstrate a middle infrared ZnGeP_2 optical parametric oscillator pumped by the Q-switched Ho：GdVO_4 laser. When the incident Ho pump power is 4.12 W, the maximum average output power of the ZGP-OPO laser is 2.05 W, corresponding to a slope efficiency of 74.6%. The ZGP-OPO laser produces 4.2 ns mid-infrared pulses at a pulse repetition rate of 5 kHz. In addition, we obtain 0.8 um of tunable range for the signal wave and 2.1 um of tunable range for the idler wave.

Zinc Oxide-Based Q-Switched Erbium-Doped Fiber Laser

We demonstrate a Q-switched erbium-doped fiber laser （EDFL） using a newly developed zinc oxide- （ZnO） based saturable absorber （SA）. The SA is fabricated by embedding a prepared ZnO powder into a poly（vinyl alcohol） film. A small piece of the film is then sandwiched between two fiber ferrules and is incorporated in an EDFL cavity for generating a stable Q-switching pulse train. The EDFL operates at 1560.4nm with a pump power threshold of 11.8mW, a pulse repetition rate tunable from 22.79 to 61.43kHz, and the smallest pulse width of 7.00 μs. The Q-switching pulse shows no spectral modulation with a peak-to-pedestal ratio of 62 dB indicating the high stability of the laser. These results show that the ZnO powder has a great potential to be used for pulsed laser applications.

Continuous-Wave and Actively Q-Switched Diode-Pumped Er:LuAG Ring Laser at 1650 nm

We demonstrate a cw and actively Q-switched Er：LuAO laser resonantly dual-end-pumped by 1532nm fibre- coupled laser diodes. A maximum cw output power of 1.9W at 1650.3nm is obtained at a pump power of 25.5 W, corresponding to a slope efficiency of 43.3 %. In the Q-switched regime, the maximum pulse energy of 3.51 mJ is reached at a pulse repetition rate of 100 Hz, a pulse duration of 90.5ns and a pump power of 25.5 W. At the repetition rate of 400 Hz, the output energy is 2.12m J, corresponding to a pulse duration of 125.4 ns.

Passive Q-Switching of a Yb:LuVO_4 Laser with Cr^(4+):YAG:Approaching the Intrinsic Upper Limit of Repetition Rate

We demonstrate a diode pumped Yb：LuVO4 laser that can be passively Q-switched by a Cr^（4＋）：YAG saturable absorber having an initial transmission as high as 99.3%.A maximum pulsed output power of 2.35 W is generated at a repetition rate of 285.7 kHz,approaching or very near the intrinsic upper limit imposed by the recovery time of the Cr^（4＋）：YAG saturable absorber,and the resulting pulse energy,duration and peak power are,respectively,8.2μJ,39.2ns and 0.209kW.

High-energy pulse generation using Yb-doped Q-switched fiber laser based on single-walled carbon nanotubes

An all-fiber laser using a single-walled carbon nanotube（SWCNT） as the saturable absorber（SA） for Q-switched operation in the 1031 nm region is demonstrated in this work. A lasing threshold as low as 17 mW was realized for continuous wave operation. By further increasing the pump power, stable Q-switched pulse trains are obtained when the pump power ranges from 38 mW to 125 mW, corresponding to repetition rate varying from 40.84 kHz to 66.24 kHz, the pulse width from 2.0 μs to 1.0 μs,and the highest single pulse energy of 40.6 nJ respectively.

High-Power Passively Q-Switched Nd:YAG Laser at 1112 nm with a Cr^(4+):YAG Saturable Absorber

A high-power passively Q-switched Nd：YAG laser operating at lll2nm with Cr4＋：yAO as a saturable absorber is demonstrated. Under 808 nm diode-direct pumping, the maximum average output power of 2.73 W is achieved at the pump power of 16.65 W, corresponding to an optical-to-optical conversion efficiency of 16.4%. At the same time, the pulse width, pulse repetition rate, single pulse energy and peak power are 27.2ns, 9 kHz, 303.3#3 and 11.2kW, respectively. As far as we know, the result gives the highest average output power at 1112nm generated by an 808 nm diode-end-pumped Nd：YAG laser.

Acousto-Optically Q-Switched Operation of Yb:CNGG Disordered Crystal Laser

We report the repetitively Q-switched laser operation of the Yb-doped calcium niobium gallium garnet disordered garnet crystal, achieved with an acousto-optic modulator in a compact plano-concave resonator that is endpumped by a 935-nm diode laser. An average output power of 1.96 W is produced at pulse repetition rate of50 k Hz at emission wavelengths around 1035 nm, with a slope efficiency of 16%. The highest pulse energy of 269 μJ is generated at pulse repetition rate of 1 k Hz, with pulse width 12.1 ns and peak power 20.53 kW.