Experimental investigation on ablation characteristics of coated and uncoated steel under 30/80 μs impulse current

The ablation tests on coated and uncoated Q235 B steel sheets were conducted under 30/80 μs impulse current simulating the lightning first return stroke current, aimed at further understanding the ablation characteristics of steel and investigating the impact of anti-corrosion coating on these characteristics. Ablation characteristics were investigated through the macroscopic morphology and x-ray diffraction patterns on the surface of damaged zones, the microstructure and micro Vickers hardness on the cross-section of damaged zones, and the maximum rear-face temperature of sample sheets. It can be concluded that the ablation areas of uncoated sheet consist of the melted layer and the heat-affect layer. These ablation areas include not only the area ablated directly by the arc root, of which the depth is deeper, but also the area forming due to the splashing of molten steel, of which the depth is shallower and decreases when the area’s distance from the arc attachment point increases. For coated sheet, coating materials have decomposed and evaporated forming an ablation pit on the sheet surface, in which the steel surface is exposed, and zinc filler of coating primer has infused into the exposed surface. The ablation diameter of uncoated sheet relates to the amplitude of the 30/80 μs impulse current in quadratic function, while for coated sheet, the relation is linear. In general, under the 30/80 μs impulse current, the coating can decrease the energy injected from the arc to the steel sheet and reduce the melting and splashing of steel. As a result, the ablation severity of uncoated sheet is severer than that of coated sheet.

Effect of Interlayers on Microstructure and Properties of 2205/Q235B Duplex Stainless Steel Clad Plate

In this research,2205/Q235 B clad plates were prepared by a vacuum hot rolling composite process.The effects of adding Fe,Ni,and Nb interlayers on the bonding interface structures and the shear strengths of the clad steel plates were studied.The results showed that 2205 duplex stainless steel and the three interlayers produced a large amount of plastic deformation and low-angle boundaries,and the main structures were the recrystallized and deformed grains.There were many recrystallized grains in the microstructure of the Q235 B low-carbon steel due to the low deformation in the rolling process.The Fe interlayer had better wettability with the two kinds of steel,but the lower strength led to the reduction of shear strength by about14 MPa compared with the original clad steel plate.The C element in the Q235 B low-carbon steel easily diffused into the Fe interlayer,and the clad steel plate attained a poor corrosion resistance because a large decarburization area was formed.The Nb interlayer reacted with the Mo element in the 2205 duplex stainless steel to form an Nb-Mo binary alloy,which generated long-banded ferrite.The decarburization area was also produced because the Nb reacted with the C element in the Q235 B to form hard and brittle NbCx.As a result,the shear strength was significantly reduced by about 282 MPa,and the corrosion resistance of the bonding surface was deteriorated.The Ni interlayer did not react with the alloy elements in both sides,and therefore effectively prevented element diffusion and improved the corrosion resistance of the bonding surface.Due to the low strength of the Ni interlayer and the increased number of bonding surfaces of the clad steel plates,the shear strength was reduced to some extent(about 40 MPa),but it still met the engineering application standards.

Influence of pass reduction ratio on microstructure and properties of 2205/Q235B clad steel plate

2205/Q235B clad steel plates were fabricated using a thermal simulator.The metallographic microscope,scanning electron microscope,energy-dispersive spectrometer,shear test,electrochemical corrosion test and acid immersion test were used to study the influence of the pass reduction ratio on the microstructure and properties of 2205/Q235B clad steel plate.The results show that the clad steel plates had a good bonding surface when the pass reduction ratios were between 16.3%and 36.0%.There existed the mutual diffusion effect of elements near the bonding surface,which caused the long austenite strip on the side of 2205 stainless steel and the decarburization layer on the side of Q235B low-carbon steel.The transformation ofδferrite toγaustenite and the generation of the decarburization layer were promoted because of the lower pass reduction ratio.The corrosio n resista nee of 2205 duplex-phases stainless steel worse ned by the decrease in 8 ferrite con tent.The increase in the decarburization layer thickness made the shear strength of the clad steel plates reduce from 453 to 390 MPa.The potential of the decarburization layer was lower than that of 2205 stainless steel and Q235B low-carb on steel,which was easily corroded in the corrosive medium.

Effect of hot rolling and cooling process on microstructure and properties of 2205/Q235 clad plate

The 2205/Q235 clad plate was fabricated by vacuum hot rolling with symmetrical assembling pattern of Q235/2205/2205/ Q235.The flow stress behavior and processing map of 2205 duplex stainless steel (DSS)were investigated by hot compressive tests on a Gleeble-3800 simulator.Then,thermal-mechanical coupled nonlinear finite element models of vacuum hot rolling and subsequent cooling process were established.From the simulation results,the influence of rolling reduction and rolling speed on hot deformation state of 2205 DSS in the assembled slab was disclosed and the optimal rolling parameters were presented.Meanwhile,the cooling rate of 2205 DSS under different cooling conditions and thicknesses of the clad plate was obtained.According to the numerical simulation results,pilot experiments were successfully carried out on a laboratory scale.The material universal testing machine,optical microscope,scanning electron microscope and energy-dispersive spectrometer were used to evaluate the mechanical properties and microstructure of bonding interface and 2205 DSS matrix for different rolling reduction and cooling processes.The results showed that with symmetrical assembling pattern,the approximate thermodynamic conditions can be established for 2205 DSS to avoid cracks in hot rolling process.When the rolling reduction increased from 10 to 40%,the shear strength of the bonding interface is increased from 120 to 530 MPa,and the uniform two-phase microstructure of 2205 DSS and satisfactory' mechanical properties can be obtained with cooling rate higher than 10℃/s between 1050 and 500℃ after rolling.