Recent Development of Quantum Dot Deposition in Quantum Dot-Sensitized Solar Cells

As new-generation solar cells,quantum dot-sensitized solar cells(QDSCs)have the outstanding advantages of low cost and high theoretical efficiency;thus,such cells receive extensive research attention.Their power conversion efficiency(PCE)has increased from 5%to over 15%in the past decade.However,compared with the theoretical efficiency(44%),the PCE of QDSCs still needs further improvement.The low loading amount of quantum dots(QDs)is a key factor limiting the improvement of cell efficiency.The loading amount of QDs on the surface of the substrate film is important for the performance of QDSCs,which directly affects the light-harvesting ability of the device and interfacial charge recombination.The optimization of QD deposition and the improvement of the loading amount are important driving forces for the rapid development of QDSCs in recent years and a key breakthrough in future development.In this paper,the research progress of QD deposition on the surface of substrate films in QDSCs was reviewed.In addition,the main deposition methods and their advantages and disadvantages were discussed,and future research on the further increase in loading amount was proposed.

200-nm long TiO_2 nanorod arrays for efficient solid-state Pb S quantum dot-sensitized solar cellsR

To ensure the infiltration of spiro-OMeTAD into the quantum dot-sensitized photoanode and to consider the limit of the hole diffusion length in the spiro-OMe TAD layer, a rutile TiO_2 nanorod array with a length of 200 nm, a diameter of 20 nm and an areal density of 720 μm^(-2) was successfully prepared using a hydrothermal method with an aqueous-grown solution of 38 m M titanium isopropoxide and 6 M hydrochloric acid at 170 °C for 75 min. Pb S quantum dots were deposited by a spin coating-assisted successive ionic layer adsorption and reaction(spin-SILAR), and all solid-state Pb S quantum dot-sensitized TiO_2 nanorod array solar cells were fabricated using spiro-OMe TAD as electrolytes. The results revealed that the average crystal size of Pb S quantum dots was ～7.8 nm using Pb(NO_3)_2 as the lead source and remain unchanged with the increase of the number of spin-SILAR cycles. The all solid-state Pb S quantum dot-sensitized TiO_2 nanorod array solar cells with spin-SILAR cycle numbers of 20, 30 and 40 achieved the photoelectric conversion efficiencies of 3.74%, 4.12% and 3.11%, respectively, under AM 1.5 G illumination(100 m W/cm^2).

TiO_2 hierarchical pores/nanorod arrays composite film as photoanode for quantum dot-sensitized solar cells

Power conversion efficiency(PCE) of quantum dot-sensitized solar cells(QDSSCs) was boosted in a TiO_2 composite film(TCSF) with delicate design in structure where TiO_2 hierarchical porous film(THPF) situated on the top of TiO_2 nanorod arrays film(TNAF). In this case, TNAF could supply efficient scattering centers for high light harvesting and direct electrical pathways for fast electron transfer while the THPF could offer porous channels for loading high quantity of previously synthetized quantum dots(QDs) and facilitate the penetration of electrolyte. Meanwhile, in this specific configuration, the presence of anatase–rutile heterojunction at the interface could help the rutile TNAF layer to efficiently collect photo-injected electrons from the anatase THPF layer thus suppressing the recombination of electrons and holes in electrolyte. The results showed that the PCE of QDSSC based on the TNAF photoanode was about 1.4-fold higher(η = 3.05%, J_(sc)= 15.86 m A cm^(-2), V_(oc)= 0.602 V, FF = 0.319) than that of device based on pure THPF(η = 2.20%, J_(sc)= 13.82 m A cm^(-2), V_(oc)= 0.572 V, FF = 0.278).

Selenium cooperated polysulfide electrolyte for efficiency enhancement of quantum dot-sensitized solar cells

The modification of polysulfide electrolyte with additives has been demonstrated as an effective way to improve the photovoltaic performance of quantum dot-sensitized solar cells(QDSCs). Most of these additives can inhibit the charge recombination processes at photoanode/electrolyte interface and favor the improvement of V oc of cell devices. Herein, we showed that the incorporation of elemental selenium(Se) in polysulfide electrolyte to form polyselenosulfide species can notably improve the performance of QDSCs. Unlike previous reports, we present here an integrated investigation of the effects of polyselenosulfide species in polysulfide electrolyte on the photovoltaic performance of QDSCs from both of the photoanode and counter electrode(CE) aspects. Electrochemical impedance spectroscopy(IS) and opencircuit voltage-decay(OCVD) measurements demonstrated that the introduction of Se into polysulfide electrolyte can not only retard charge recombination at photoanode/electrolyte interface, but also reduce the charge transfer resistance at CE/electrolyte interface, resulting in the improvement of J sc and FF values. Consequently, the average efficiency of Zn-Cu-In-Se QDSCs was improved from 9.26% to 9.78% under AM 1.5 G full one sun illumination.

A series of conducting gel electrolytes for quasi-solid-state quantum dot-sensitized solar cells with boosted electron transfer processes

To pursue electron-generation stability with no sacrifice of photovoltaic performance has been a persistent objective for all kinds of solar cells. Here, we demonstrate the experimental realization of this objective by quasi-solid-state quantum dot-sensitized solar cells from a series of conducting gel electrolytes composed of polyacrylamide(PAAm) matrix and conductive polymers [polyaniline(PANi), polypyrrole(PPy) or polythiophene(PT)]. The reduction of S_x^(2-) occurred in both interface and three dimensional framework of conducting gel electrolyte as a result of the electrical conduction of PANi, PPy and PT toward refluxed electrons from external circuit to Pt electrode. The resulting solar cells can yield the solarto-electrical conversion efficiency of 2.33%, 2.25% and 1.80% for PANi, PPy and PT based gel electrolytes,respectively. Those solar cells possessed much higher efficiency than that of 1.74% based on pure PAAm gel electrolyte owing to the enhanced kinetics for S_x^(2-) ? S^(2-) conversion. More importantly, the stability of quasi-solid-state solar cell is significantly advanced, arising from the localization of liquid electrolyte into the three dimensional framework and therefore reduced leakage and volatilization.

Quantum dot-sensitized solar cells employing Pt/C_(60) counter electrode provide an efficiency exceeding 2%

A microporous platinum/fullerenes (Pt/C 60) counter electrode was prepared by using a facile rapid thermal decomposition method,and the quantum-dot sensitized solar cell (QDSSC) of Pt/C 60-TiO 2-CdS-ZnS and Pt/C 60-TiO 2-CdTe-ZnS was fabrication.The technique forms a good contact between QDs and TiO 2 films.The photovoltaic performances of the as-prepared cells were investigated.The QDSSCs with Pt/C 60 counter electrode show high power conversion efficiency of 1.90% and 2.06%,respectively (under irradiation of a simulated solar light with an intensity of 100 mW cm 2),which is comparable to the one fabricated using conventional Pt electrode.

Modeling and Simulation of Heterojunction Solar Cell with Mono Crystalline Silicon

The monocrystalline silicon is a promising material that could be used in solar cells that convert light into electricity. Although the cost of ordinary silicon (Si) solar cells has decreased significantly over the past two decades, the conversion efficiency of these cells has remained relatively high. While solar cells have a great potential as a device of renewable energy, the high cost they incur per Watt continues to be a significant barrier to their widespread implementation. As a consequence, it is vital to conduct research into alternate materials that may be used in the construction of solar cells. The heterojunction solar cell (HJSC), which is based on n-type zinc oxide (n-ZnO) and p-type silicon (p-Si), is one of the numerous alternatives of the typical Si single homojunction solar cell. There are many deficiencies that can be found in the published research on n-ZnO/p-Si heterojunction solar cell. Inconsistencies in the stated value of open circuit voltage (Voc) of the solar cell are one example of deficiency. The absence of a full theoretical study to evaluate the potential of the solar cell structure is another deficiency that can be found in these researches. A lower value of experimentally obtained VOC in comparison to the theoretical prediction based on the band-gap between n-ZnO and p-Si. There needs to be more consensus among scientists regarding the optimal conditions for the growth of zinc oxide. Many software’s are available for simulating and optimizing the solar cells based on these parameters. For this purpose, in this dissertation, I provide computational results relevant to n-ZnO/p-Si HJSC to overcome deficiencies that have been identified. While modeling and simulating the potential of the solar cell structure with AFORS-HET, it is essential to consider the constraints that exist in the real world. AFORS-HET was explicitly designed to mimic the multilayer solar cell arrangement. In AFORS-HET, we can add up to seven layers for solar cell layout. By using this software, we can figure out the open circuit voltage (VOC), the short circuit current (JSC), the quantum efficiency (QE, %), the heterojunction energy band structure, and the power conversion efficiency (PCE).

Nano-capillary induced assemble of quantum dots on perovskite grain boundaries for efficient and stable perovskite solar cells

In recent years, perovskite solar cells(PSCs) have propelled into the limelight owing to rapid development of efficiency;however, the abundant defects at the perovskite grain boundaries result in unwanted energy loss and structural degradation. Here, the grain boundaries of perovskite polycrystalline films have been found to act as nanocapillaries for capturing perovskite quantum dots(PQDs), which enable the conformal assemble of PQDs at the top interspace between perovskite grains. The existence of PQDs passivated the surface defects, optimized the interfacial band alignments, and ultimately improved the power conversion efficiency from 19.27% to 22.47% in inverted PSCs. Our findings open up the possibility of selective assembly and structural modulation of the perovskite nanostructures towards efficient and stable PSCs.

Efficient quantum dot sensitized solar cells via improved loading amount management

High light-harvesting efficiency and low interfacial charge transfer loss are essential for the fabrication of high-efficiency quantum dot-based solar cells(QDSCs). Increasing the thickness of mesoporous TiO2films can improve the loading of pre-synthesized QDs on the film and enhance the absorbance of photoanode, but commonly accompanied by the increase in the unfavorable charge recombination due to prolonged electron transmission paths. Herein, we systematically studied the influence of the balance between QD loading and TiO2film thickness on the performance of QDSCs. It is found that the relative thin photoanode prepared by the cationic surfactant-assisted multiple deposition procedure has achieved a high QD loading which is comparable to that of the thick photoanode commonly used. Under AM 1.5G illumination, Zn–Cu–In–Se and Zn–Cu–In–S based QDSCs with optimized 11.8 μm photoanodes show the PCE of 10.03% and 8.53%, respectively, which are comparable to the corresponding highest PCE of Zn–Cu–In–Se and Zn–Cu–In–S QDSCs(9.74% and 8.75%) with over 25.0 μm photoanodes. Similarly, an impressive PCE of 6.14% was obtained for the CdSe based QDSCs with a 4.1 μm photoanode, which is slightly lower than the best PCE(7.05%)of reference CdSe QDSCs with 18.1 μm photoanode.

Review of roll-to-roll fabrication techniques for colloidal quantum dot solar cells

Colloidal quantum dots(CQDs)are of great interest to photovoltaic(PV)technologies as they possess the benefits of solution-processability,size-tunability,and roll-to-roll manufacturability,as well as unique capabilities to harvest near-infrared(NIR)radiation.During the last decade,lab-scale CQD solar cells have achieved rapid improvement in the power conversion efficiency(PCE)from~1%to 18%,which will potentially exceed 20%in the next few years and approach the performance of other PV technologies,such as perovskite solar cells and organic solar cells.In the meanwhile,CQD solar cells exhibit long lifetimes either under shelf storage or continuous operation,making them highly attractive to industry.However,in order to meet the industrial requirements,mass production techniques are necessary to scale up the fabrication of those lab devices into large-area PV modules,such as roll-to-toll coating.This paper reviews the recent developments of large-area CQD solar cells with a focus on various fabrication methods and their principles.It covers the progress of typical large-area coating techniques,including spray coating,blade coating,dip coating,and slot-die coating.It also discusses next steps and new strategies to accomplish the ultimate goal of the low-cost large-area fabrication of CQD solar cells and emphasizes how artificial intelligence or machine learning could facilitate the developments of CQD solar cell research.

In Situ Iodide Passivation Toward Efficient CsPbI_(3) Perovskite Quantum Dot Solar Cells

All-inorganic CsPbI_3 quantum dots(QDs) have demonstrated promising potential in photovoltaic(PV) applications. However, these colloidal perovskites are vulnerable to the deterioration of surface trap states, leading to a degradation in efficiency and stability. To address these issues, a facile yet effective strategy of introducing hydroiodic acid(HI) into the synthesis procedure is established to achieve high-quality QDs and devices. Through an in-depth experimental analysis, the introduction of HI was found to convert PbI_2 into highly coordinated [PbI_m]~(2-m), enabling control of the nucleation numbers and growth kinetics. Combined optical and structural investigations illustrate that such a synthesis technique is beneficial for achieving enhanced crystallinity and a reduced density of crystallographic defects. Finally, the effect of HI is further reflected on the PV performance. The optimal device demonstrated a significantly improved power conversion efficiency of 15.72% along with enhanced storage stability. This technique illuminates a novel and simple methodology to regulate the formed species during synthesis, shedding light on ofurther understanding solar cell performance, and aiding the design of future novel synthesis protocols for high-performance optoelectronic devices.

Recent progress of colloidal quantum dot based solar cells

Colloidal quantum dot(CQD) solar cells have attracted great interest due to their low cost and superior photo-electric properties. Remarkable improvements in cell performances of both quantum dot sensitized solar cells(QDSCs) and PbX(X = S, Se) based CQD solar cells have been achieved in recent years, and the power conversion efficiencies(PCEs) exceeding 12% were reported so far. In this review, we will focus on the recent progress in CQD solar cells. We firstly summarize the advance of CQD sensitizer materials and the strategies for enhancing carrier collection efficiency in QDSCs, including developing multi-component alloyed CQDs and core-shell structured CQDs, as well as various methods to suppress interfacial carrier recombination. Then, we discuss the device architecture development of PbX CQD based solar cells and surface/interface passivation methods to increase light absorption and carrier extraction efficiencies. Finally, a short summary, challenge, and perspective are given.

Recent Progress of Layered Perovskite Solar Cells Incorporating Aromatic Spacers

Layered two dimensional(2D) or quasi-2D perovskites are emerging photovoltaic materials due to their superior environment and structure stability in comparison with their 3D counterparts. The typical 2D perovskites can be obtained by cutting 3D perovskites along < 100 > orientation by incorporation of bulky organic spacers, which play a key role in the performance of 2D perovskite solar cells(PSCs). Compared with aliphatic spacers, aromatic spacers with high dielectric constant have the potential to decrease the dielectric and quantum confinement effect of 2D perovskites, promote efficient charge transport and reduce the exciton binding energy, all of which are beneficial for the photovoltaic performance of 2D PSCs. In this review, we aim to provide useful guidelines for the design of aromatic spacers for 2D perovskites. We systematically reviewed the recent progress of aromatic spacers used in 2D PSCs. Finally, we propose the possible design strategies for aromatic spacers that may lead to more efficient and stable 2D PSCs.

Surface-Modified Graphene Oxide/Lead Sulfide Hybrid Film-Forming Ink for High-Efficiency Bulk Nano-Heterojunction Colloidal Quantum Dot Solar Cells

Solution-processed colloidal quantum dot solar cells(CQDSCs) is a promising candidate for new generation solar cells.To obtain stable and high performance lead sulfide(PbS)-based CQDSCs,high carrier mobility and low non-radiative recombination center density in the PbS CQDs active layer are required.In order to effectively improve the carrier mobility in PbS CQDs layer of CQDSCs,butylamine(BTA)-modified graphene oxide(BTA@GO) is first utilized in PbS-PbX2(X=I-,Br-) CQDs ink to deposit the active layer of CQDSCs through one-step spin-coating method.Such surface treatment of GO dramatically upholds the intrinsic superior hole transfer peculiarity of GO and attenuates the hydrophilicity of GO in order to allow for its good dispersibility in ink solvent.The introduction of B TA@GO in CQDs layer can build up a bulk nano-heterojunction architecture,which provides a smooth charge carrier transport channel in turn improves the carrier mobility and conductivity,extends the carriers lifetime and reduces the trap density of PbS-PbX2 CQDs film.Finally,the BTA@GO/PbS-PbX2 hybrid CQDs film-based relatively large-area(0.35 cm2) CQDSCs shows a champion power conversion efficiency of 11.7% which is increased by 23.1% compared with the control device.

Higher open-circuit voltage set by cobalt redox shuttle in SnO_2 nanofibers-sensitized CdTe quantum dot solar cells

In this study, we report an efficient CdTe-SnO_2 quantum dot(QD) solar cell fabricated by heat-assisted drop-casting of hydrothermally synthesized CdTe QDs on electrospun SnO_2 nanofibers. The as-prepared QDs and SnO_2 nanofibers were characterized by dynamic light scattering(DLS), UV–Vis spectroscopy,photoluminescence(PL) spectra, X-ray diffraction(XRD) and transmission electron microscopy(TEM). The SnO_2 nanofibers deposited on fluorine-doped tin oxide(SnO_2) and sensitized with the CdTe QDs were assembled into a solar cell by sandwiching against a platinum(Pt) counter electrode in presence of cobalt electrolyte. The efficiency of cells was investigated by anchoring QDs of varying sizes on SnO_2. The best photovoltaic performance of an overall power conversion efficiency of 1.10%, an open-circuit voltage(Voc)of 0.80 V, and a photocurrent density(JSC) of 3.70 m A/cm^2 were obtained for cells with SnO_2 thickness of5–6 μm and cell area of 0.25 cm^2 under standard 1 Sun illumination(100 m W/cm^2). The efficiency was investigated for the same systems under polysulfide electrolyte as well for a comparison.

Antireflection Coating for Solar Cells Based on Graded-Index Materials

The conversion of sunlight into electricity via photovoltaics presents tremendous opportunities for the generation of renewable energy. However, solar cells still face several challenges and limitations to further reduce manufacturing costs and increase module efficiency. Photon management is paramount to increase the efficiency of the mainstream silicon-based cell and always includes a suitable antireflection coating (ARC) structure to decrease the reflectance (R) at the top surface. We propose a novel triple-layer anti-reflective coating (TLAR) consisting of three layers sandwiched between the upper cover (glass) and the substrate (silicon). The inner three layers are graded refractive index material (GIM) as an active layer, titanium dioxide (TiO2), and zinc sulfide (ZnS), respectively. The optical properties of the TLAR have been investigated using the transfer matrix method (TMM). The results of using GIM as the active medium lead to the reflection decaying to the minimum value, and the transmittance reaching the maximum values at a specific wavelength range. The proposed triple-layer anti-reflective coating (TLAR) structure presents a promising solution for enhancing the efficiency of solar cells. Its unique design and utilization of graded refractive index material (GIM) as the active layer make it a novel and innovative approach that holds great potential for advancing solar cell technology.

Ligand engineering of colloid quantum dots and their application in all-inorganic tandem solar cells

How to effectively utilize the energy of the broad spectrum of sunlight is one of the basic problems in the research of tandem solar cells. Due to their size effect, quantum confinement effect and coupling effect, colloidal quantum dots(QDs) exhibit new physical properties that bulk materials don’t possess.CdX(X = Se, S, etc.) and Pb X(X = Se, S, etc.) QDs prepared by hot-injection methods have been widely studied in the areas of photovolitaic devices. However, the surfactants surrounding QDs seriously hinder the charge transport of QDs based solar cells. Therefore, how to fabricate high-performance tandem solar cells via ligands engineering has become a major challenge. In this paper, the latest progress of colloidal QDs in the research of all-inorganic tandem solar cells was summarized. Firstly, the improvement of QDs surface ligands and the optimization of ligands engineering were discussed, and the control of the physical properties of QDs films were realized. From the aspects of colloidal QDs, ligand engineering, and solar cell preparation, the future development direction of colloidal QDs solar cells was proposed, providing technical guidances for the preparation of low-cost and high-efficiency nanocrystalline solar cells.

Composite Semiconductor Quantum Dots CdSe/CdS Co-sensitized TiO_2 Nanorod Array Solar Cells

CdSe/CdS semiconductor quantum dots co-sensitized TiO2 nanorod array was fabricated on the transparent conductive fluorine-doped tin oxide (FTO) substrate using the hydrothermal and successive ionic layer adsorption and reaction (SILAR) process. The structural and morphological properties of the samples were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), and transmission electron microscopy (TEM). The results indicate that CdSe/CdS QDs are uniformly coated on the surface of the TiO2 nanorods. The shift of light absorption edge was monitored by taking UV-visible absorption spectra. Compared with the absorption spectra of the TiO2 nanorod array, deposition of CdSe/CdS QDs shifts the absorption edge to the higher wavelength. The enhanced light absorption in the visible-light region of CdSe/CdS/TiO2 nanorod array indicates that CdSe/CdS layers can act as co-sensitizers in quantum dots sensitized solar cells (QDSSCs). By optimizing the CdSe layer deposition cycles, a photocurrent of 5.78 mA/cm2, an open circuit photovoltage of 0.469 V and a conversion efficiency of 1.34 % were obtained under an illumination of 100 mw/cm2.

CdS Quantum Dots-sensitized TiO_2 Nanotube Arrays for Solar Cells

CdS quantum dots(QDs) sensitized TiO2 nanotube arrays photoelectrodes were investigated for their photovoltaic performance of quantum dots-sensitized solar cells. The highly ordered TiO2 nanotube arrays(TNAs) were synthesized on Ti foils by anodic oxidation method. Then CdS quantum dots were deposited onto the TiO2 nanotube arrays by successive ionic layer absorption and reaction(SILAR) method to serve as the sensitizers. Cd(NO3)2 and Na2S were used as the precursor materials of Cd+ and S2- ions, respectively. It is found that the CdS QDs sensitizer may significantly increase the light response of TiO2 nanotube arrays. With increasing CdS QDs deposition cycles, the visible light response increases. Maximum photocurrent was obtained for the QDs that have an absorption peak at about 500 nm. Under AM 1.5 G illuminations(100 mW cm-2), a 4.85 mA/cm2 short circuit current density was achieved, and the maximium energy conversion efficiency of the as-prepared CdS QDs-sensitized TNAs solar cells was obtained as high as 0.81 % at five SILAR cycles.