Solar steam generation(SSG)is widely regarded as one of the most sustainable technologies for seawater desalination.However,salt fouling severely compromises the evaporation performance and lifetime of evaporators,lim...Solar steam generation(SSG)is widely regarded as one of the most sustainable technologies for seawater desalination.However,salt fouling severely compromises the evaporation performance and lifetime of evaporators,limiting their practical applications.Herein,we propose a hierarchical salt-rejection(HSR)strategy to prevent salt precipitation during long-term evaporation while maintaining a rapid evaporation rate,even in high-salinity brine.The salt diffusion process is segmented into three steps—insulation,branching diffusion,and arterial transport—that significantly enhance the salt-resistance properties of the evaporator.Moreover,the HSR strategy overcomes the tradeoff between salt resistance and evaporation rate.Consequently,a high evaporation rate of 2.84 kg m^(-2) h^(-1),stable evaporation for 7 days cyclic tests in 20 wt%NaCl solution,and continuous operation for 170 h in natural seawater under 1 sun illumination were achieved.Compared with control evaporators,the HSR evaporator exhibited a>54%enhancement in total water evaporation mass during 24 h continuous evaporation in 20 wt%salt water.Furthermore,a water collection device equipped with the HSR evaporator realized a high water purification rate(1.1 kg m^(-2) h^(-1)),highlighting its potential for agricultural applications.展开更多
This research investigates the behavior of a 2×2 pile group under two-directional lateral loads in addition to the vertical load.Through three-dimensional numerical modeling based on Flac 3D software,the study ex...This research investigates the behavior of a 2×2 pile group under two-directional lateral loads in addition to the vertical load.Through three-dimensional numerical modeling based on Flac 3D software,the study examines the total bearing capacity and efficiency coefficient of the pile group,considering factors such as the angle of lateral load,relative pile spacing,and relative stiffness of the pile-soil system.The findings highlight the significance of these factors in understanding and predicting the response of pile groups to changing lateral load directions.The results reveal that increasing the angle of the lateral load from 0°to 45°enhances both the maximum total lateral load and the efficiency coefficient of the pile group.When the relative stiffness of the pile-soil system significantly increases,soil stiffening occurs and reducing the relative spacing of the piles from 7 to 3 times the diameter of the piles diminishes the influence of the pile group.Consequently,the response of the pile group to lateral loads becomes more linear,with only a slight alteration in the maximum total lateral load and the efficiency coefficient when the lateral load is angled from 0°to 45°.Conversely,increasing the relative distance between the piles,specifically from 3 to 7 times the diameter of the piles,amplifies the influence of the pile group.Both the maximum total lateral load and the efficiency coefficient of the pile group exhibit an observed increase.These provide insights for designing pile groups and optimizing their performance under lateral loading conditions.展开更多
The Gouméré region is located in the North-East of Côte d’Ivoire and is located in the South-West of the Bui furrow. In order to highlight the geology of the area studied, 14 samples were taken for stu...The Gouméré region is located in the North-East of Côte d’Ivoire and is located in the South-West of the Bui furrow. In order to highlight the geology of the area studied, 14 samples were taken for studies using petrographic, geochemical and metallogenic methods. The study of macroscopic and microscopic petrography made it possible to highlight two major lithological units: 1) a volcano-plutonic unit, formed of gabbros, basalt, volcaniclastics and rhyodacite;2) a sedimentary unit (microconglomerate). From a geochemical point of view, the results obtained indicate that the plutonites are gabbro and gabbro diorite while the volcanics have compositions of basaltic andesites, rhyolite and dacites. The sediments have a litharenitic to sublitharenitic character. The metallogenic study made it possible to highlight hydrothermal alterations and metalliferous paragenesis on the formations studied. Hydrothermal alteration is characterized by the presence of carbonation, silicification, sericitization, sulfidation and to a lesser degree chloritization. Metalliferous paragenesis consists of pyrite, chalcopyrite, hematite and magnetite.展开更多
Climate change is an alarming global challenge, particularly affecting the least developed countries (LDCs) including Liberia. These countries, located in regions prone to unpredictable temperature and precipitation c...Climate change is an alarming global challenge, particularly affecting the least developed countries (LDCs) including Liberia. These countries, located in regions prone to unpredictable temperature and precipitation changes, are facing significant challenges, particularly in climate-sensitive sectors such as mining and agriculture. LDCs need more resilience to adverse climate shocks but have limited capacity for adaptation compared to other developed and developing nations. This paper examines Liberia’s susceptibility to climate change as a least developed country, focusing on its exposure, sensitivity, and adaptive capacity. It provides an overview of LDCs and outlines the global distribution of carbon dioxide emissions. The paper also evaluates specific challenges that amplify Liberia’s vulnerability and constrain sustainable adaptation, providing insight into climate change’s existing and potential effects. The paper emphasizes the urgency of addressing climate impacts on Liberia and calls for concerted local and international efforts for effective and sustainable mitigation efforts. It provides recommendations for policy decisions and calls for further research on climate change mitigation and adaptation.展开更多
In this paper, we investigate the energy efficiency and spectrum efficiency, including one-hop device-to-device(D2D) communications mode and two-way amplify-and-forward(AF) relaying D2D communications mode in underlay...In this paper, we investigate the energy efficiency and spectrum efficiency, including one-hop device-to-device(D2D) communications mode and two-way amplify-and-forward(AF) relaying D2D communications mode in underlay D2D communications enabled cellular networks. An analysis of average energy efficiency and spectrum efficiency are developed and closed-form expressions are obtained for two types of D2D communications modes under the effect of Rayleigh fading channel, path loss, and co-channel interference. Analytical results are validated through numerical simulations. Based on the simulation, the effects of the interference, the distance between D2D pair and the position of relay node on the energy efficiency and spectrum efficiency of D2D communications are investigated. The optimal D2D transmission powers of these two modes to maximize the energy efficiency are also investigated.展开更多
Non-condensable gas(NCG),foam and surfactant are the three commonly-used additives in hybrid steam-chemical processes for heavy oil reservoirs.Their application can effectively control the steam injection profile and ...Non-condensable gas(NCG),foam and surfactant are the three commonly-used additives in hybrid steam-chemical processes for heavy oil reservoirs.Their application can effectively control the steam injection profile and increase the sweep efficiency.In this paper,the methods of microscale visualized experiment and macroscale 3D experiment are applied to systematically evaluate the areal and vertical sweep efficiencies of different hybrid steam-chemical processes.First,a series of static tests are performed to evaluate the effect of different additives on heavy oil properties.Then,by a series of tests on the microscale visualized model,the areal sweep efficiencies of a baseline steam flooding process and different follow-up hybrid EOR processes are obtained from the collected 2D images.Specifically,they include the hybrid steam-N_(2)process,hybrid steam-N2/foam process,hybrid steam-surfactant process and hybrid steam-N2/foam/surfactant process(N2/foam slug first and steam-surfactant co-injection then).From the results of static tests and visualized micromodels,the pore scale EOR mechanisms and the difference between them can be discussed.For the vertical sweep efficiencies,a macroscale 3D experiment of steam flooding process and a follow-up hybrid EOR process is conducted.Thereafter,combing the macroscale 3D experiment and laboratory-scaled numerical simulation,the vertical and overall sweep efficiencies of different hybrid steam-chemical processes are evaluated.Results indicate that compared with a steam flooding process,the areal sweep efficiency of a hybrid steam-N2process is lower.It is caused by the high mobility ratio in a steam-N2-heavy oil system.By contrast,the enhancement of sweep efficiency by a hybrid steam-N2/foam/surfactant process is the highest.It is because of the high resistance capacity of NCG foam system and the performance of surfactant.Specifically,a surfactant can interact with the oil film in chief zone and reduce the interfacial energy,and thus the oil droplets/films formed during steam injection stage are unlocked.For NCG foam,it can plug the chief steam flow zone and thus the subsequent injected steam is re-directed.Simultaneously,from the collected 2D images,it is also observed that the reservoir microscopic heterogeneity can have an important effect on their sweep efficiencies.From the 3D experiment and laboratory-scaled numerical simulation,it is found that a N2/foam slug can increase the thermal front angle by about 150 and increase the vertical sweep efficiency by about 26%.Among the four processes,a multiple hybrid EOR process(steam-N2/foam/surfactant process) is recommended than the other ones.This paper provides a novel method to systematically evaluate the sweep efficiency of hybrid steam-chemical process and some new insights on the mechanisms of sweep efficiency enhancement are also addressed.It can benefit the expansion of hybrid steam-chemical processes in the post steamed heavy oil reservoirs.展开更多
Aiming at the energy consumption of long-distance device-to-device(D2D) devices for two-way communications in a cellular network,this paper proposes a strategy that combines two-way relay technology(TWRT) and simultan...Aiming at the energy consumption of long-distance device-to-device(D2D) devices for two-way communications in a cellular network,this paper proposes a strategy that combines two-way relay technology(TWRT) and simultaneous wireless information and power transfer(SWIPT) technology to achieve high energy efficiency(EE) communication.The scheme first establishes a fractional programming problem to maximize EE of D2D,and transforms it into a non-fractional optimization problem that can be solved easily.Then the problem is divided into three sub-problems:power control,power splitting ratios optimization,and relay selection.In order to maximize EE of the D2D pair,the Dinkelbach iterative algorithm is used to optimize the transmitted power of two D2D devices simultaneously;the one-dimensional search algorithm is proposed to optimize power splitting ratios;an improved optimal relay selection scheme based on EE is proposed to select relay.Finally,experiments are carried out on the Matlab simulation platform.The simulation results show that the proposed algorithm has faster convergence.Compared with the one-way relay transmission and fixed relay algorithms,the proposed scheme has higher EE.展开更多
The work’s objective is to analyze the influence of the saturation temperature of the R134a refrigerant on the thermal performance of a shell and tube type condenser, with water and aluminum oxide (Al<sub>2<...The work’s objective is to analyze the influence of the saturation temperature of the R134a refrigerant on the thermal performance of a shell and tube type condenser, with water and aluminum oxide (Al<sub>2</sub>O<sub>3</sub>) nanoparticles flowing into the tube. For analysis, the heat exchanger is subdivided into three regions: subcooled liquid, saturated steam, and superheated steam. The shell and tube heat exchanger assumed as the basis for the study has 36 tubes, with rows of 4 tubes in line and three passes into the tube in each region. The parameters used to analyze the performance are efficiency and effectiveness, through variations of quantities such as saturation temperature, the nanofluid’s mass flow rate, fraction in the nanoparticles’ volume, and the number of passes in the tube in each region of the heat exchanger. The obtained results demonstrate that the efficiency is relatively high in all the analyzed situations. In each saturation temperature, the effectiveness can be increased by introducing fractions of nanoparticles in the water or increasing the number of passes in the tube.展开更多
This paper is a revised and expanded version of a paper entitled “The static and dynamic criteria of building an investment asset portfolio” presented at International Conference on Applied Economics (ICOAE, 2014), ...This paper is a revised and expanded version of a paper entitled “The static and dynamic criteria of building an investment asset portfolio” presented at International Conference on Applied Economics (ICOAE, 2014), Chania, 3-5 July 2014 and published at Procedia Economics and Finance, Volume 14, Pages 575-584 (2014) [1]. At the previous research, it showed the significance to go beyond the scope of selecting one or another metric of static efficiency. And the attention was paid to the dynamic efficiency criteria. The ICOAE 2015 research gives brief results of that work, which is only one of applied areas of polydimensional efficiency measurement model (PEMM). Research work on PEMM conceptual and methodical elaboration has been started in the author’s dissertation study [2] and continued in the practical activity and materialized in Innovative LLC (limited liability company) creating project. The research is concentrating on the real economic benefit of 3D PEMM (thee criterial PEMM version) implementation. In the first part of ICOAE 2015 empirical study, the dynamic component of 3D PEMM on the industrial level was tested. Next, the company economic profit changes and dynamic-market 3D PEMM components correlation was estimated. Finally, the economic benefit of 3D PEMM functional operationalization in the framework of management systems development was calculated.展开更多
基金support provided by the Shenzhen-Hong Kong Science and Technology Innovation Cooperation Zone Shenzhen Park Project(HZQB-KCZYB-2020030)the Research Grants Council of Hong Kong(Project No:AoE/M-402/20.)+1 种基金the Open Project of Yunnan Precious Metals Laboratory Co.,Ltd(YPML-2023050248)the Hong Kong Innovation and Technology Commission via the Hong Kong Branch of National Precious Metals Material Engineering Research Center.
文摘Solar steam generation(SSG)is widely regarded as one of the most sustainable technologies for seawater desalination.However,salt fouling severely compromises the evaporation performance and lifetime of evaporators,limiting their practical applications.Herein,we propose a hierarchical salt-rejection(HSR)strategy to prevent salt precipitation during long-term evaporation while maintaining a rapid evaporation rate,even in high-salinity brine.The salt diffusion process is segmented into three steps—insulation,branching diffusion,and arterial transport—that significantly enhance the salt-resistance properties of the evaporator.Moreover,the HSR strategy overcomes the tradeoff between salt resistance and evaporation rate.Consequently,a high evaporation rate of 2.84 kg m^(-2) h^(-1),stable evaporation for 7 days cyclic tests in 20 wt%NaCl solution,and continuous operation for 170 h in natural seawater under 1 sun illumination were achieved.Compared with control evaporators,the HSR evaporator exhibited a>54%enhancement in total water evaporation mass during 24 h continuous evaporation in 20 wt%salt water.Furthermore,a water collection device equipped with the HSR evaporator realized a high water purification rate(1.1 kg m^(-2) h^(-1)),highlighting its potential for agricultural applications.
文摘This research investigates the behavior of a 2×2 pile group under two-directional lateral loads in addition to the vertical load.Through three-dimensional numerical modeling based on Flac 3D software,the study examines the total bearing capacity and efficiency coefficient of the pile group,considering factors such as the angle of lateral load,relative pile spacing,and relative stiffness of the pile-soil system.The findings highlight the significance of these factors in understanding and predicting the response of pile groups to changing lateral load directions.The results reveal that increasing the angle of the lateral load from 0°to 45°enhances both the maximum total lateral load and the efficiency coefficient of the pile group.When the relative stiffness of the pile-soil system significantly increases,soil stiffening occurs and reducing the relative spacing of the piles from 7 to 3 times the diameter of the piles diminishes the influence of the pile group.Consequently,the response of the pile group to lateral loads becomes more linear,with only a slight alteration in the maximum total lateral load and the efficiency coefficient when the lateral load is angled from 0°to 45°.Conversely,increasing the relative distance between the piles,specifically from 3 to 7 times the diameter of the piles,amplifies the influence of the pile group.Both the maximum total lateral load and the efficiency coefficient of the pile group exhibit an observed increase.These provide insights for designing pile groups and optimizing their performance under lateral loading conditions.
文摘The Gouméré region is located in the North-East of Côte d’Ivoire and is located in the South-West of the Bui furrow. In order to highlight the geology of the area studied, 14 samples were taken for studies using petrographic, geochemical and metallogenic methods. The study of macroscopic and microscopic petrography made it possible to highlight two major lithological units: 1) a volcano-plutonic unit, formed of gabbros, basalt, volcaniclastics and rhyodacite;2) a sedimentary unit (microconglomerate). From a geochemical point of view, the results obtained indicate that the plutonites are gabbro and gabbro diorite while the volcanics have compositions of basaltic andesites, rhyolite and dacites. The sediments have a litharenitic to sublitharenitic character. The metallogenic study made it possible to highlight hydrothermal alterations and metalliferous paragenesis on the formations studied. Hydrothermal alteration is characterized by the presence of carbonation, silicification, sericitization, sulfidation and to a lesser degree chloritization. Metalliferous paragenesis consists of pyrite, chalcopyrite, hematite and magnetite.
文摘Climate change is an alarming global challenge, particularly affecting the least developed countries (LDCs) including Liberia. These countries, located in regions prone to unpredictable temperature and precipitation changes, are facing significant challenges, particularly in climate-sensitive sectors such as mining and agriculture. LDCs need more resilience to adverse climate shocks but have limited capacity for adaptation compared to other developed and developing nations. This paper examines Liberia’s susceptibility to climate change as a least developed country, focusing on its exposure, sensitivity, and adaptive capacity. It provides an overview of LDCs and outlines the global distribution of carbon dioxide emissions. The paper also evaluates specific challenges that amplify Liberia’s vulnerability and constrain sustainable adaptation, providing insight into climate change’s existing and potential effects. The paper emphasizes the urgency of addressing climate impacts on Liberia and calls for concerted local and international efforts for effective and sustainable mitigation efforts. It provides recommendations for policy decisions and calls for further research on climate change mitigation and adaptation.
基金supported by the National Natural Science Foundation of China under Grant U1805262, 61871446, 61671251 and 61701201the Natural Science Foundation of Jiangsu Province under Grant No.BK20170758+2 种基金the Natural Science Foundation for colleges and universities of Jiangsu Province under Grant No.17KJB510011the open research fund of National Mobile Communications Research Laboratory,Southeast University under Grant No.2015D10Project of Key Laboratory of Wireless Communications of Jiangsu Province under Grant No.NK214001
文摘In this paper, we investigate the energy efficiency and spectrum efficiency, including one-hop device-to-device(D2D) communications mode and two-way amplify-and-forward(AF) relaying D2D communications mode in underlay D2D communications enabled cellular networks. An analysis of average energy efficiency and spectrum efficiency are developed and closed-form expressions are obtained for two types of D2D communications modes under the effect of Rayleigh fading channel, path loss, and co-channel interference. Analytical results are validated through numerical simulations. Based on the simulation, the effects of the interference, the distance between D2D pair and the position of relay node on the energy efficiency and spectrum efficiency of D2D communications are investigated. The optimal D2D transmission powers of these two modes to maximize the energy efficiency are also investigated.
基金financially supported by the National Natural Science Foundation of China(U20B6003,52004303)Beijing Natural Science Foundation(3212020)
文摘Non-condensable gas(NCG),foam and surfactant are the three commonly-used additives in hybrid steam-chemical processes for heavy oil reservoirs.Their application can effectively control the steam injection profile and increase the sweep efficiency.In this paper,the methods of microscale visualized experiment and macroscale 3D experiment are applied to systematically evaluate the areal and vertical sweep efficiencies of different hybrid steam-chemical processes.First,a series of static tests are performed to evaluate the effect of different additives on heavy oil properties.Then,by a series of tests on the microscale visualized model,the areal sweep efficiencies of a baseline steam flooding process and different follow-up hybrid EOR processes are obtained from the collected 2D images.Specifically,they include the hybrid steam-N_(2)process,hybrid steam-N2/foam process,hybrid steam-surfactant process and hybrid steam-N2/foam/surfactant process(N2/foam slug first and steam-surfactant co-injection then).From the results of static tests and visualized micromodels,the pore scale EOR mechanisms and the difference between them can be discussed.For the vertical sweep efficiencies,a macroscale 3D experiment of steam flooding process and a follow-up hybrid EOR process is conducted.Thereafter,combing the macroscale 3D experiment and laboratory-scaled numerical simulation,the vertical and overall sweep efficiencies of different hybrid steam-chemical processes are evaluated.Results indicate that compared with a steam flooding process,the areal sweep efficiency of a hybrid steam-N2process is lower.It is caused by the high mobility ratio in a steam-N2-heavy oil system.By contrast,the enhancement of sweep efficiency by a hybrid steam-N2/foam/surfactant process is the highest.It is because of the high resistance capacity of NCG foam system and the performance of surfactant.Specifically,a surfactant can interact with the oil film in chief zone and reduce the interfacial energy,and thus the oil droplets/films formed during steam injection stage are unlocked.For NCG foam,it can plug the chief steam flow zone and thus the subsequent injected steam is re-directed.Simultaneously,from the collected 2D images,it is also observed that the reservoir microscopic heterogeneity can have an important effect on their sweep efficiencies.From the 3D experiment and laboratory-scaled numerical simulation,it is found that a N2/foam slug can increase the thermal front angle by about 150 and increase the vertical sweep efficiency by about 26%.Among the four processes,a multiple hybrid EOR process(steam-N2/foam/surfactant process) is recommended than the other ones.This paper provides a novel method to systematically evaluate the sweep efficiency of hybrid steam-chemical process and some new insights on the mechanisms of sweep efficiency enhancement are also addressed.It can benefit the expansion of hybrid steam-chemical processes in the post steamed heavy oil reservoirs.
基金Supported by the National Natural Science Foundation of China (No.61561031)。
文摘Aiming at the energy consumption of long-distance device-to-device(D2D) devices for two-way communications in a cellular network,this paper proposes a strategy that combines two-way relay technology(TWRT) and simultaneous wireless information and power transfer(SWIPT) technology to achieve high energy efficiency(EE) communication.The scheme first establishes a fractional programming problem to maximize EE of D2D,and transforms it into a non-fractional optimization problem that can be solved easily.Then the problem is divided into three sub-problems:power control,power splitting ratios optimization,and relay selection.In order to maximize EE of the D2D pair,the Dinkelbach iterative algorithm is used to optimize the transmitted power of two D2D devices simultaneously;the one-dimensional search algorithm is proposed to optimize power splitting ratios;an improved optimal relay selection scheme based on EE is proposed to select relay.Finally,experiments are carried out on the Matlab simulation platform.The simulation results show that the proposed algorithm has faster convergence.Compared with the one-way relay transmission and fixed relay algorithms,the proposed scheme has higher EE.
文摘The work’s objective is to analyze the influence of the saturation temperature of the R134a refrigerant on the thermal performance of a shell and tube type condenser, with water and aluminum oxide (Al<sub>2</sub>O<sub>3</sub>) nanoparticles flowing into the tube. For analysis, the heat exchanger is subdivided into three regions: subcooled liquid, saturated steam, and superheated steam. The shell and tube heat exchanger assumed as the basis for the study has 36 tubes, with rows of 4 tubes in line and three passes into the tube in each region. The parameters used to analyze the performance are efficiency and effectiveness, through variations of quantities such as saturation temperature, the nanofluid’s mass flow rate, fraction in the nanoparticles’ volume, and the number of passes in the tube in each region of the heat exchanger. The obtained results demonstrate that the efficiency is relatively high in all the analyzed situations. In each saturation temperature, the effectiveness can be increased by introducing fractions of nanoparticles in the water or increasing the number of passes in the tube.
文摘This paper is a revised and expanded version of a paper entitled “The static and dynamic criteria of building an investment asset portfolio” presented at International Conference on Applied Economics (ICOAE, 2014), Chania, 3-5 July 2014 and published at Procedia Economics and Finance, Volume 14, Pages 575-584 (2014) [1]. At the previous research, it showed the significance to go beyond the scope of selecting one or another metric of static efficiency. And the attention was paid to the dynamic efficiency criteria. The ICOAE 2015 research gives brief results of that work, which is only one of applied areas of polydimensional efficiency measurement model (PEMM). Research work on PEMM conceptual and methodical elaboration has been started in the author’s dissertation study [2] and continued in the practical activity and materialized in Innovative LLC (limited liability company) creating project. The research is concentrating on the real economic benefit of 3D PEMM (thee criterial PEMM version) implementation. In the first part of ICOAE 2015 empirical study, the dynamic component of 3D PEMM on the industrial level was tested. Next, the company economic profit changes and dynamic-market 3D PEMM components correlation was estimated. Finally, the economic benefit of 3D PEMM functional operationalization in the framework of management systems development was calculated.