Oxidation of Partially Hydrolyzed Polyacrylamide from Polymer Flooding Processes Using Fenton Reagents

The degradation of partially hydrolyzed polyacrylamide(HPAM) found in alkaline/surfactant/polymer flooding sewage was investigated using Fenton-type reagents. Different Fenton reagent treatments for HPAM degradation were compared. The effects of pH, hydrogen peroxide(H_(2)O_(2)), ferrous ion(Fe^(2+)), and tartaric ion(C_(4)H_(4)O_(6)^(2-)) concentrations were studied. The degradation reaction occurred within a wide range of pH(3–9). The HPAM degradation performance of photo-Fenton processes using solar light and UV were compared with that of the Fenton process. The degradation rate was found to be strongly dependent on the H_(2)O_(2)/Fe^(2+)/C_(4)H_(4)O_(6)^(2-)molar ratio. The HPAM degradation efficiency was 90%, and the chemical oxygen demand removal efficiency was 85%. HPAM could be degraded into a compound with a lower molecular weight, but it was difficult to achieve complete mineralization to CO_(2). The presence of intermediate products hindered further oxidation in the Fenton process.

Effect of reagent films on coupling relationship between glass surface and particles

The experiments were conducted to investigate the behavior of airborne particles adhering to the glass slides which were coated by several reagent films. The results showed that the adhesion level could be significantly changed by the reagent films. There were no evident rules between the average size of particles and sampling time interval, the placing angle and reagent concentration. The average particle size on the surface coated by composite reagent （2-3 μm） was smaller than that on the single reagent coated surface, while the largest particle size （4-5 μm） was observed on the surface coated with the Tween 60. The experiment also demonstrated that the best adhesive performance was obtained on the surface which was coated with 0.5% SDBS and 0.5% fluorocarbon composite reagents. The experiment results indicated that each reagent had a certain optimum adhesive range to the particle. The composite reagents with different proportion of single reagents exhibited some particular physical and chemical properties, which could effectively change the adhesive performance between the solid surface and the particles.

Reagent types and action mechanisms in ilmenite flotation:A review

Ilmenite is an essential mineral for the extraction of titanium.Conventional physical separation methods have difficulty recovering fine ilmenite,and dressing plants have begun applying flotation to recover ilmenite.The interaction of reagent groups with Ti and Fe sites on the ilmenite surface dramatically influences the ilmenite flotation.However,the investigation on Fe sites has received more attention because the activity of Ti is lower than that of Fe.For the activators on ilmenite flotation,most are metal ions but typically lead ions.The metal ions of activators promote ilmenite flotation by increasing the active sites on the ilmenite surface.Combined reagents have a better selective separation of ilmenite than single reagents due to their synergistic effect.Combining the lead ion(Pb^(2+))and the benzyl hydroxamic acid(BHA)into a Pb-BHA complex has a marked effect on ilmenite flotation,which puts forward a new idea of developing combined reagents for ilmenite flotation.This review considers reagent types and action mechanisms in ilmenite flotation.On the basis of the analysis of previous research,a brief future outlook of reagent types and action mechanisms in ilmenite flotation is also proposed in this study.

Preparation of ZnO Nanoparticles and Photocatalytic H2 Production Activity from Different Sacrificial Reagent Solutions

ZnO nanoparticles were synthesized via a direct precipitation method followed by a hetero- geneous azeotropic distillation and calcination processes, and then characterized by X-ray power diffraction, scanning electron microscopy, transmission electron microscopy, and ni- trogen adsorption-desorption measurement. The effects of Pt-loading amount, calcination temperature, and sacrificial reagents on the present ZnO suspension were investigated, photocatalytic H2 evolution efficiency from the The experimental results indicate that ZnO rianoparticles calcined at 400℃ exhibit the best photoactivity for the H2 production in comparison with the samples calcined at 300 and 500℃, and the photoeatalytie H2 production efficiency from a methanol solution is much higher than that from a triethanolamine solution. It can be ascribed to the oxidization of methanol also contributes to the H2 production during the photochemical reaction process. Moreover, the photocatalytic mechanism for the H2 production from the present ZnO suspension system containing methanol solution is also discussed in detail.

Colorimetric Method for Determination of Amino Acids on Thin Layer and Filter Paper Chromatography Using a Modified Ninhydrin Reagent

A simple and rapid colorimetric method for the and Whatman filter paper chromatography is described. determination of some amino acids on thin layer chromatography （TLC） The studied compounds are cysteine, proline, methionine, tryptophan glutmine, glycine, thyrosine, threonine, leucine and lysine. The method is based on the formation of color from the reaction of stannous chloride （SnCI2） and ninhydrin reagents. The procedure has been successfully applied to the assay of the standard amino acid preparation after TLC separation, and the results of the studied compounds were clear and favorable, comparing to the official methods. However, the improved TLC is much more efficient for the detection of amino acid. The main advantage of this method is that the detection of amino acids can be preformed visually.

Exploitation of Fenton and Fenton-like reagents as alternative conditioners for alum sludge conditioning

The use of Fenton＇s reagent （Fe^2＋/H2O2） and Fenton-like reagents containing transition metals of Cu（Ⅱ）, Zn（Ⅱ）, Co（Ⅱ）, and Mn（Ⅱ） for an alum sludge conditioning to improve its dewaterability was investigated. The results obtained were compared with those obtained from conditioning the same alum sludge using cationic and anionic polymers. Experimental results show that Fenton＇s reagent was the best among the Fenton and Fenton-like reagents for the alum sludge conditioning. A considerable effectiveness of capillary suction time （CST） reduction efficiency of 47% can be achieved under test conditions of Fe^2＋/H2O2 = 20/125 mg/g DS （dry solid） and pH 6.0. The observation of floc-like particles after Fenton＇s reagent conditioning of alum sludge suggested that the mechanism of Fenton＇s reagent conditioning was different from that of polymer conditioning. In spite of the lower efficiency in the CST reduction of Fenton＇s reagent in alum sludge conditioning compared to that of polymer conditioning, Fenton＇s reagent offers a more environmentally safe option. Tiffs study provided an example of proactive treatment engineering, which is aimed at seeking a safe alternative to the use of polymers in sludge conditioning towards achieving a more sustainable sludge management strategy.

Mechanisms of aid-leaching reagent calcium fluoride in the extracting vanadium processes from stone coal

The mechanisms of aid-leaching reagent calcium fluoride in the extracting vanadium processes were researched by comparing the blank extraction with the extraction with calcium fluoride as aid-leaching reagent. The leaching experiments were carried out under the conditions of 95 ~C, 6 h, 1.5 ml.g-1, 15 vol % H2SO4, and 5 % calcium fluoride （mass ratio of CaF2 to stone coal）. The concentrations of hydrogen ion were adjusted from initial 1.82 and 4.79 mol.L-1 to the pH of 1.80 4- 0.05 by 200 g.L-1 lime milk, respectively. The solvent extraction experiments were carded out under the organic phase using 15 vol% D2EHPA, 5 vol% TBP, and 80 vol% sulfonated kerosene and O/A phase ratio of 1/4. The leaching rate of vanadium and six-stage countercurrent solvent extraction rate of vanadium can be remarkably improved from 66.71 to 92.97 % and 81.15 to 98.81%, respectively, when calcium fluoride was added as aid-leaching reagent. In the leaching process, fluorine can enhance the breakage of the structure of vanadium-bearing minerals. Meanwhile, fluoride ion can combine with iron ion to generate acid-insoluble iron fluoride hydrate （Fe2Fs.7H20） and consume all ferric ions and a portion of ferrous ions. In adjusting pH value process, the massive impurities are decreased to form KA1SO4 and FeA1Fs. In solvent extraction process, fluorine can prevent the formation of ferric hydroxide colloids and eliminate the formed unstable ferric hydroxide colloids and the silicon-containing colloids to promote the sufficient contact between the aqueous phase and the organic phase and the sufficient reaction.

Diagnosis of spontaneous bacterial peritonitis: An update on leucocyte esterase reagent strips

Ascites remain the commonest complication of decompensated cirrhosis. Spontaneous bacterial peritonitis (SBP) is defined as the infection of ascitic fluid (AF) in the absence of a contiguous source of infection and/or an intraabdominal inflammatory focus. An AF polymorphonuclear (PMN) leucocyte count ≥ 250/mm 3 -irrespective of the AF culture resultis universally accepted nowadays as the best surrogate marker for diagnosing SBP. Frequently the results of the manual or automated PMN count do not reach the hands of the responsible medical personnel in a timely manner. However, this is a crucial step in SBP management. Since 2000, 26 studies (most of them published as full papers) have checked the validity of using leukocyte esterase reagent strips (LERS) in SBP diagnosis. LERS appear to have low sensitivity for SBP, some LERS types more than others. On the other hand, though, LERS have consistently given a high negative predictive value (> 95% in the majority of the studies) and this supports the use of LERS as a preliminary screening tool for SBP diagnosis. Finally, an AF-tailored dipstick has been developed. Within the proper setting, it is set to become the mainstream process for handling AF samples.

Degradation of polyvinyl-alcohol wastewater by Fenton’s reagent: Condition optimization and enhanced biodegradability

The pretreatment of refractory polyvinyl-alcohol （PVA） wastewater with low value of CODcr by Fenton＇s reagent was investigated to enhance the biodegradabilily. The effects of operating conditions such as pH of the solution, Fe2＋ dosage, H2O2 dosage, reaction time and initial PVA concentration on the removal efficiency of CODCr were discussed. It is demonstrated that the optimum value of pH for removal of CODcr is 5 and the most suitable dosages of H2O2 （2%） and FeSO4 （10 mg/L） are 5% and 8.0%, respectively. When the initial CODcr value of the PVA water is 760 mg/L, the favorable reaction time is 110 min. Under these optimum conditions, the removal ratio of CODcr is 58.6% 61.4%, and the value of biodegradability （CODB/CODcr） increases markedly from 8.9% 9.7% to 62.6% 68.3%.

Optimization of efficient stable reagent of alkaline thiourea solution for gold leaching

Na2SiO3 and Na2SeO3 were chosen as stable reagents of alkaline thiourea solution substituting Na2SO3, according to the structure-property relationship between the stability of alkaline thiourea and the structure of thiourea and sulfite ion, and the effect of the stable reagents on stability of alkaline thiourea was investigated. The results show that contrary to Na2SeO3, Na2SO3 and Na2SiO3 affect the stability of alkaline thiourea solution remarkably. The stable effect of Na2SiO3 on alkaline thiourea is obviously better than that of Na2SO3. The stable reagents Na2SO3 and Na2SiO3 decrease the decomposition rate of alkaline thiourea solution greatly, and the decomposition rate of alkaline thiourea reduces from （72.5%） to （33.8%） with addition of (0.3 mol·L-1) Na2SiO3. Dissolution currents of gold in the alkaline thiourea solution containing Na2SO3 and Na2SiO3 are （2.0） (mA·cm-2) and （3.5） (mA·cm-2) at the potential of 0.42 V, respectively, and Na2SO3 is consumed excessively due to the oxidation reaction of Na2SO3 occurring in the studied potential range. Na2SiO3 is an efficient stable reagent of alkaline thiourea solution, and gold dissolution is accelerated much more obviously by Na2SiO3 than by Na2SO3.

Interaction effects of flotation reagents for SAG mill reject of copper sulphide ore using response surface methodology

Flotation reagents have a complex behaviour in the beneficiation of base minerals in clayey ores.Interaction effects of reagents on the efficiency of copper flotation for a highly clayey low-grade sulphide ore were investigated using a central composite design.Preliminary results showed that sodium-isopropyl-xanthate(SIPX)and O-isopropyl-N-ethyl-thionocarbamate(IPETC)were found to be the most efficient collectors in the presence of lime as the pH regulator.The effects of dosage of collectors(SIPX and IPETC)and the dosage of methyl-isobutyl-carbonyl(MIBC)as frother on the separation efficiency were evaluated at different pH levels.Based on the analysis of variance(ANOVA),the interaction effects of the collector−pH and collector−frother were significant for the separation efficiency.At the low level of collector dosage,increasing pH from 9 to 11 enhanced copper separation efficiency from 81%to 86%for IPETC and from 77%to 86%for SIPX.Results of ANOVA showed that the maximum copper separation efficiency(88.7%)was obtained at the dosages of 8.6 g/t SIPX,7 g/t IPETC and 20 g/t MIBC at pH 11.Finally,it was concluded that a mixture of SIPX and IPETC collectors was more suitable to treat highly clayey sulphide ores.

芬顿试剂(Fenton's reagent法降解对苯二酚和工业废水

可溶性亚铁盐和H2O2的组合称为芬顿试剂(Fenton’s reagent),是一种氧化能力很强的氧化剂,常用于废水的净化处理。本文以对苯二酚为代表物,探讨用Fenton试剂氧化的反应条件,并用最佳的实验条件处理工业废水,90分钟工业废水的COD去除率可达71.6％。

Novel Synthetic Method for the Vilsmeier-Haack Reagent and Green Routes to Acid Chlorides, Alkyl Formates, and Alkyl Chlorides

An environmentally benign and practical preparation method for the Vilsmeier-Haack reagent (VH) has been developed by using phthaloyl dichloride with DMF in toluene or 2-chlorotoluene. Phthalic anhydride as the byproduct was recovered in high yield by simple filtration. Some aromatic acids have been transformed into the corresponding acid chlorides in good yields by employing the isolated VH. Treatment of primary or secondary alcohols with VH gave alkyl formates or alkyl chlorides by depending on the reaction conditions.

Degradation of 4-Chlorophenol Solution by Synergetic Effect of Dual-frequency Ultrasound with Fenton Reagent

4-Chlorophenol (4-CP) solution was treated by dual-frequency ultrasound inconjunction with Fenton reagent, and obvious improvement in the 4-CP degradation rate was observedin this advanced oxidation process. Experimental results showed that ultrasonic intensity,saturating gas and pH value affected greatly the 4-CP removal rate. Among four different saturatinggases (Ar, O_2, air and N_2), 4-CP degradation with Ar-saturated solution was the best. However, inthe view of practical wastewater treatment, using oxygen as the saturating gas would be moreeconomical. The addition of Fenton reagent followed the first-order kinetics and increased the 4-CPdegradation rate. The 4-CP removal rate increased by around 126% within 15 min treatment. Thesynergetic effect of dual-frequency ultrasound with Fenton reagent on 4-CP degradation was obviouslyobserved.

Studies on New Additions to 5-Methoxy-2 (5H)-Furanone: 1, 4-Addition of Grignard Reagents, and 1,3-Dipolar Cycloaddition of Silyl Nitronates

1,4-Addition reaction of Grignard's reagent to 5-methoxy-2(5H)-furanone 1 was accomplished. which provided a new possible route for synthesizing beta -alkyl-Y-alkyloxy-Y-butyrolactone. A novel concise method of preparing fused heterocyclic compounds was offered by 1,3-dipolar cycloaddition reaction of silyl nitronates to 1.

Optimization of reagent dosages for copper flotation using statistical technique

The effects of Z11 and AP407 collectors as well as AF65 and AF70 frothers were evaluated in the rougher flotation circuit of the Sungun copper concentrator plant using 2 4 full factorial design.Response functions were produced for both Cu grade and recovery and optimized within the experimental range.The optimum reagent dosages were found to be 12.01 g/t Z11,11 g/t AP407,3 g/t AF65 and 5 g/t AF70 to attain the maximum Cu grade(8.17%).The reagent dosages of 12 g/t Z11,11 g/t AP407,3 g/t AF65 and 15 g/t AF70 produced the maximum Cu recovery(86.44%).The collector distribution demonstrated that the distribution pattern of(32%,32%,20%,16%)can produce the best recovery(87.75%)in comparison to other examined distribution patterns.

Quantitative Correlation between Group Connectivity Index and Property of Flotation Reagent

Topological method is applied firstly to calculate the group connectivity indexes of some flotation reagents for sulfide minerals and oxide minerals. The study reveals that some properties of flotation reagents, such as group electronegativity, energy criterion, solubility product of chemicals and maximum wavelength of ultraviolet absorbency, have linear correlation with the first order group connectivity index (GCI) of polar group, and the related coefficients are all larger than 0.900. The GCI can be used to characterize the structure of groups, and is a sort of new effective structural parameter to study the quantitative structure activity relationship of flotation reagents.

Reagent optimization for on-line simultaneous polarographic determination of trace amounts of Cu^(2+), Cd^(2+) and Co^(2+) in the presence of anextremely large excess of Zn^(2+)

Reagents are optimized for the simultaneous determination of trace amounts of Cu^(2+), Cd^(2+) and Co^(2+) in zinc sulfate solution, which contains an extremely large excess of Zn^(2+). First, the reagents and their doses for the experiment are selected according to the characteristics of the zinc sulfate solution. Then, the reagent doses are optimized by analyzing the influence of reagent dose on the polarographic parameters(i.e. half-wave potential E_(1/2) and limiting diffusion current I_p). Finally, the optimization results are verified by simultaneously determining trace amounts of Cu^(2+), Cd^(2+) and Co^(2+) in the presence of an extremely large excess of Zn^(2+). The determination results indicate that the optimized reagents exhibit wide linearity, low detection limits, high accuracy and good precision for the simultaneous determination of trace amounts of Cu^(2+), Cd^(2+) and Co^(2+) in the presence of an extremely large excess of Zn^(2+).

A novel method for the spectrophotometric determination of cefradine by using sodium nitroprusside as chromogenic reagent

A novel method is developed for the determination of cefradine by using sodium nitroprusside as chromogenic reagent. The experiment indicates that a russety product is formed by the reaction of cefradine with sodium nitroprusside in basic solution, and the maximum absorption wavelength （λmax） of russety product is 505 rim. And the sensitization of tetradecyl benzyl dimethyl ammonium chloride for the reaction of cefradine with sodium nitroprusside is remarkable, The apparent molar absorption coefficient （5505） is 2.81 × 103 L/mol cm. The linear equation isA = 0.0657 ＋ 0.00804C （μg/mL） in the range of 1.50-55.0μg/mL of cefradine with a correlation coefficient r = 0.9992, and the detection limit is 1.38 p,g/mL. This method has been applied to determine cefradine in capsule and tablet samples.