Effect of benzoxazine resin on mechanical properties of nitrile rubber composites: Experiment and molecular simulation

Benzoxazine resin,being a new type of phenolic resin deve-loped to overcome the shortcomings of traditional phenolic resins,has been synthesized from phenol,formaldehyde and amine,and does not require solvent elimination or monomer purification to obtain a relatively clean precursor.It has potential application in the field of aerospace due to its low expansion coefficient,high weather resistance,high carbon yield,good mechanical strength,and excellent ablation resistance[1].It can be mixed with various other resins or polymers to produce new resins with a broad range of applications[2-3].

Particle agglomeration and inhibition method in the fluidized pyrolysis reaction of waste resin

This work investigated the pyrolysis reaction of waste resin in a fluidized bed reactor.It was found that the pyrolysis-generated ash would adhere to the surface of ceramic particles,causing particle agglomeration and defluidization.Adding kaolin could effectively inhibit the particle agglomeration during the fluidized pyrolysis reaction through physical isolation and chemical reaction.On the one hand,kaolin could form a coating layer on the surface of ceramic particles to prevent the adhesion of organic ash generated by the pyrolysis of resin.On the other hand,when a sufficient amount of kaolin(-0.2%(mass))was added,the activated kaolin could fully contact with the Na+ ions generated by the pyrolysis of resin and react to form a high-melting aluminosilicate mineral(nepheline),which could reduce the formation of low-melting-point sodium sulfate and thereby avoid the agglomeration of ceramic particles.

Cardo poly (ether sulfone) toughened E51/DETDA epoxy resin and its carbon fiber composites

A toughener that can effectively improve the interlaminar toughness in carbon fiber composites is crucial for various applications.We investigated,the toughening effects of phenolphthalein-based cardo poly(ether sulfone)(PES-C)on E51/DETDA epoxy and its carbon fiber composites(CFCs).Scanning electron microscopy showed that the phase structures of PES-C/epoxy blends change from island(of dispersed phase)structures to bi-continuous structures(of the matrix)as the PES-C content increased,which is associated with reaction-induced phase separation.After adding 15 phr PES-C,the glass transition temperature(T_(g))of the blends increased by 51.5℃,and the flexural strength,impact strength and fracture toughness of the blends were improved by 41.1%,186.2%and 42.7%,respectively.These improvements could be attributed to the phase separation structure of the PES-C/epoxy sys-tem.A PES-C film was used to improve the mode-II fracture toughness(G_(IIC))of CFCs.The G_(IIC) value of the 7μm PES-C film toughened laminate was improved by 80.3%compared to that of the control laminate.The increase in G_(IIC) was attributed to cohesive failure and plastic deformation in the interleaving region.

B-COPNA resin formation from ethylene tar light fractions:Process development and mechanical exploration by molecular simulation

An efficient utilization strategy of ethylene tar(ET),the main by-product of the ethylene cracking unit,is urgently required to meet demands for modern petrochemical industry.On the other hand,condensed polynuclear aromatic resin of moderate condensation degree(B-COPNA)is a widely used carbon material due to its superb processability,the production of which is,however,seriously limited by the high cost of raw materials.Under such context,an interesting strategy was proposed in this study for producing B-COPNA resin using crosslinked light fractions of ethylene tar(ETLF,boiling point<260℃)facilitated by molecular simulation.1,4-Benzenedimethanol(PXG)was first selected as the crosslinking agent according to the findings of molecular simulation.The effects of operating conditions,including reactions temperature,crosslinking agent,and catalyst content on the softening point and yield of B-COPNA resin products were then investigated to optimize the process.The reaction mechanism of resin production was studied by analyzing the molecular structure and transition state of ETLF and crosslinking agents.It was shown that PXG exhibited a superior capacity of withdrawing electrons and a higher electrophilic reactivity than other crosslinking agents.In addition to the highest yield and greatest heat properties,PXG-prepared resin contained the most condensed aromatics.The corresponding optimized conditions of resin preparation were 180℃,1:1.9(PXG:ETLF),and 3%(mass)of catalyst content with a resin yield of 78.57%.It was the electrophilic substitution reaction that occurred between the ETLF and crosslinking agent molecules that were responsible for the resin formation,according to the experimental characterization and molecular simulation.Hence,it was confirmed that the proposed strategy and demonstrated process can achieve a clean and high value-added utilization of ETLF via B-COPNA resin preparation,bringing huge economic value to the current petrochemical industry.

Enhanced corrosion resistance of epoxy resin coating via addition of CeO_(2) and benzotriazole

The use of fillers to enhance the corrosion protection of epoxy resins has been widely applied.In this work,cerium dioxide(CeO_(2))and benzotriazole(BTA)were introduced into an epoxy resin to enhance the corrosion resistance of Q235 carbon steel.Scanning electron microscopy results indicated that the CeO_(2) grains were rod-like and ellipsoidal in shape,and the distribution pattern of BTA was analyzed by energy dispersive spectroscope.The dynamic potential polarization curve proved the excellent corrosion resistance of the composite epoxy resin with CeO_(2) and BTA co-addition,and electrochemical impedance spectroscopy test analysis indicated the significantly enhanced long-term corrosion protection performance of the composite coating.And the optimal protective performance was provided by the coating containing 0.3%(mass)CeO_(2) and 20%(mass)BTA,which was attributed to the barrier performance of CeO_(2) particles and the chemical barrier effect of BTA.The formation of corrosion products was analyzed using X-ray diffraction.In addition,the corrosion resistance mechanism of the coating was also discussed in detail.

Effect of Epoxy Resin on the Properties of Recycled Asphalt

To promote the recycling of reclaimed asphalt pavement(RAP),epoxy resin was used to prepare the epoxy-recycled asphalt mixtures.The effect of epoxy resin on the properties of aged asphalt binder was investigated based on the tensile test,flexural creep test,and laser scanning confocal microscopy.The curing characteristics and the mechanical performance of recycled asphalt with different epoxy contents were explored.The results show that the low-temperature performance,ductility,and strength of the aged asphalt binder were significantly improved when the epoxy content reached 40%.The curing time of epoxy-recycled asphalt should be at least 4 d to ensure the formation of good internal spatial network structure.

Optimization Mechanism of Mechanical Properties of Basalt Fiber-Epoxy Resin Composites by Interfacially Enriched Distribution of Nano-Starch Crystals

Fibre reinforced polymer composites have become a new generation of structural materials due to their unique advantages such as high specific strength,designability,good dimensional stability and ease of large-area monolithic forming.However,the problem of interfacial bonding between the resin matrix and the fibres limits the direct use of reinforcing fibres and has become a central difficulty in the development of basalt fibre-epoxy composites.This paper proposes a solution for enhancing the strength of the fibre-resin interface using maize starch nanocrystals,which are highly yield and eco-friendly.Firstly,in this paper,corn starch nanocrystals(SNC)were prepared by hydrolysis,and were deposited on the surface of basalt fibers by electrostatic adsorption.After that,in order to maximize the modification effect of nano-starch crystals on the interface,the basalt fiber-epoxy resin composite samples were prepared by mixing in a pressureless molding method.The test results shown that the addition of basalt fibers alone led to a reduction in the strength of the sample.Deposition of 0.1 wt%SNC on the surface of basalt fibers can make the strength consistent with pure epoxy resin.When the adsorption amount of SNC reached 0.5 wt%,the tensile strength of the samples was 23.7%higher than that of pure epoxy resin.This is due to the formation of ether bond homopolymers between the SNC at the fibre-epoxy interface and the epoxy resin,which distorts the originally smooth interface,leading to increased stress concentration and the development of cracks.This enhances the binding of basalt fibers.The conclusions of this paper can provide an effective,simple,low-cost and non-polluting method of interfacial enhancement modification.

Evaluating two stages of silicone-containing arylene resin oxidation via experiment and molecular simulation

Silicon-containing aryl acetylene resin(PSA)is a new type of high-temperature resistant resin with excellent oxidation resistance,whereas antioxidant reaction mechanism of PSA resin under ultra-high temperatures still remains unclear.Herein,the oxidation behavior and mechanisms of PSA resin are systematically investigated combining kinetic analysis and Reax FF molecular dynamics(MD)simulations.Thermogravimetric analysis indicates that the oxidation process of PSA resin undergoes two main steps:oxidative mass gain and oxidative degradation.The distributed activation energy model(DAEM)is employed for describing oxidation processes and the best-fit one is obtained using genetic algorithms and differential evolution.DAEM model demonstrates that the oxidative weight gain stage is dominated by two virtual reactants and the oxidative degradation stage consists of three virtual reactants.Correspondingly,the observation of MD reaction pathways indicates that oxygen oxidation of unsaturated structures occurs in the initial stage,which results in the formation of PSA resin oxides.Furthermore,cracked pieces react with O_(2)to generate CO and other chemicals in the second step.The resin matrix's great antioxidation resilience is illustrated by the formation of SiO_(2).The analysis based on MD simulations exhibits an efficient computational proof with the experiments and DAEM methods.Based on the results,a two-stage reaction mechanism is proposed,which provides important theoretical support for the subsequent study of the oxidation behavior of silica-based resins.

Adsorption behaviors and mechanisms of gold recovery from thiosulfate solution by ion exchange resin

The adsorption behaviors and mechanisms of gold from thiosulfate solution on strong-base anion exchange resin were systematically investigated.The comparison experiment of adsorption ability and selectivity for gold showed that gel Amberlite IRA-400 resin with Type Ⅰ quaternary ammonium functional group had better adsorption performance.The increases of resin dosage,ammonia concentration and solution pH were favorable to gold adsorption,whereas the rises of cupric and thiosulfate concentrations were disadvantageous to gold loading.Microscopic characterization results indicated that gold was adsorbed in the form of [Au(S_(2)O_(3))_(2)]^(3–) complex anion by exchanging with the counter ion Cl^(–) in the functional group of the resin.Density functional theory calculation result manifested that gold adsorption was mainly depended on the hydrogen bond and van der Waals force generated between O atom in [Au(S_(2)O_(3))_(2)]^(3–) and H atom in the quaternary ammonium functional group of the resin.

Evaluation of the injection and plugging ability of a novel epoxy resin in cement cracks

Sustained casing pressure(SCP)is a crucial issue in the oil and gas production lifecycle.Epoxy resins,exhibiting exceptional compressive strength,ductility,and shear bonding strength,have the potential to form reliable barriers.The injectivity and sealing capacity of the epoxy resin is crucial parameters for the success of shallow remediation operations.This study aimed to develop and assess a novel solid-free resin sealant as an alternative to Portland cement for mitigating fluid leakage.The investigation evaluated the viscosity,compressive strength,and brittleness index of the epoxy resin sealant,as well as its tangential and normal shear strengths in conjunction with casing steel.The flow characteristics and sealing abilities of conventional cement and epoxy resin were comparatively analyzed in cracks.The results showed that the application of a viscosity reducer facilitated control over the curing time of the epoxy resin,ranging from 1.5 to 6 h,and reduced the initial viscosity from 865.53 to 118.71 m Pa,s.The mechanical properties of the epoxy resin initially increased with a rise in curing agent content before experiencing a minor decrease.The epoxy resin containing 30%curing agent exhibited optimal mechanical properties.After a 14-day curing period,the epoxy resin's compressive strength reached81.37 MPa,2.12 times higher than that of cement,whereas the elastic modulus of cement was 2.99 times greater than that of the epoxy resin.The brittleness index of epoxy resin is only 3.42,demonstrating high flexibility and toughness.The tangential and normal shear strengths of the epoxy resin exceeded those of cement by 3.17 and 2.82 times,respectively.In a 0.5 mm-wide crack,the injection pressure of the epoxy resin remained below 0.075 MPa,indicating superior injection and flow capabilities.Conversely,the injection pressure of cement surged dramatically to 2.61 MPa within 5 min.The breakthrough pressure of0.5 PV epoxy resin reached 7.53 MPa,decreasing the crack's permeability to 0.02 D,a mere 9.49%of the permeability observed following cement plugging.Upon sealing a 2 mm-wide crack using epoxy resin,the maximum breakthrough pressure attained 5.47 MPa,3.48 times of cement.These results suggest that epoxy resin sealant can be employed safely and effectively to seal cracks in the cement.

Preparation and Swelling Kinetic Analysis of Poly (HPMC-co-AA-co-AM) Super Absorbent Resin

Super absorbent resin(SAR)is prepared by aqueous high temperature polymerization using hydroxypropyl methylcellulose(HPMC)as monomer backbone material,acrylic acid(AA)and acrylamide(AM)as the graft copolymer monomer,potassium persulfate(KPS)as the initiator to generate free radicals,and N,N`-methylenebisacrylamide(MBA)as cross-linking agent for cross-linking reaction.Simutaneously,the influence of individual factors on the water absorption is investigated,and these factors are mainly AA,AM,KPS,MBA,HPMC,and reaction temperature.The optimized conditions are obtained by the experiment repeating for several times.The water absorption multiplicity and salt absorption multiplicity under the conditions are 782.4 and 132.5 g/g,respectivity.Furthermore,the effects of different temperatures and salt concentrations on its water absorption,as well as the swelling kinetics of SAR are studied.It is indicated the water-absorbing swelling process is mainly caused by the difference in water osmotic pressure and Na+concentration inside and outside the cross-linked molecular structure of the resin,which is not only consistent with the quasi-secondary kinetic model,but also with the Fick diffusion model.

Kinetics and Mechanism of Hydration of Acrylic Acid over Ion-exchanged Resin:Experimental Exploration and DFT Calculation

Liquid-phase acrylic acid hydration over solid-phase catalysts is a key reaction for the industrial productionof 3-hydroxypropionic acid. However, the relevant literature primarily focuses on the experimental aspects of catalystscreening and exploring reaction conditions, with few accurate descriptions of the reaction kinetics and determination ofthe reaction mechanism. Here, we combined kinetics experiments and theoretical calculations to elucidate the kinetics andmechanism of acrylic acid hydration on a resin catalyst. The pseudo-homogeneous model, and Langmuir-Hinshelwood-Haugen-Watson and Elie-Riedel (ER) heterogeneous models were used to explain the experimental kinetics data. TheER model can explain the experimental data very well, suggesting strong adsorption of acrylic acid on the surface of theresin catalyst. Furthermore, density functional theory calculations show that the hydration follows a stepwise, rather than aconcerted, reaction pathway. The present study provides theoretical insights into the reaction mechanism and kinetics, fillingthe gap in our understanding of the reaction on a fundamental level.

Preparation of Environmentally Friendly Urea-Hexanediamine-Glyoxal(HUG)Resin Wood Adhesive

Using non-toxic,low-volatile glyoxal to completely replace formaldehyde for preparing urea-glyoxal(UG)resin adhesive is a hot research topic that could be of great interest for the wood industry.However,urea-glyoxal(UG)resins prepared by just using glyoxal instead of formaldehyde usually yields a lower degree of polymerization.This results in a poorer bonding performance and water resistance of UG resins.A good solution is to pre-react urea to preform polyurea molecules presenting already a certain degree of polymerization,and then to condense these with glyoxal to obtain a novel UG resin.Therefore,in this present work,the urea was reacted with hexamethylene diamine to form a polyurea named HU,and then this was used to react it with different amounts of glyoxal to synthesize hexamethylenediamine-urea-glyoxal(HUG)polycondensation resins,and to use this for bonding plywood.The results show that the glyoxal can well react with HU polyuria via addition and schiff base reaction,and also the HUG resin exhibits excellent bonding strength and water resistance.The shear strength of the plywood bonded with this HUG at 160°C hot press temperature as high as 1.93 MPa,2.16 MPa and 1.61 MPa,respectively,which meets the requirement of the China national standard GB/T 9846-2015(≥0.7 MPa),and can be a good choice as a wood adhesive for industrial application.

Numerical Simulation of the Mechanical Stirring Process in a Tannin-Based Foaming Precursor Resin

Tannin foam is a new functional material.It can be widely applied to the automobile industry,construction industry,and packaging industry due to its wide range of raw materials,renewable,easily degraded,low cost and almost no pollution.Preparing tannin foam is a very complex process that includes high temperature,two phases,mechanical agitation,and phase change.To investigate the influence of the stirring velocity and paddle shape,simulation was calculated by making use of the volume of fluid(VOF)method and multiple reference frame(MRF)method in a three-dimensional flow field of tannin-based foaming precursor resin.The gas holdup and velocity magnitude were analysed with various conditions of mechanical velocities and paddle shape in the stirring flow field.The result shows the higher the velocity,the greater the disturbance and paddle shape between the eggbeater and the Rushton turbine,obviously the paddle shape of the eggbeater with a wider range of agitation,which can entrap more air into the tannin-based foaming precursor resin in a short time.Especially when the speed is 1500 rpm,the flow field of the Rushton turbine comes out of a ditch,which decreases the efficiency of mass transfer;there is less air to mix into the tannin-based foaming precursor resin,which causes unevenness.At the same time,the eggbeater shows the marvelous capability of hybrid as it has two vortexes and multiple cycles that make a difference from the Rushton turbine,which has only one vortex and two upper and lower loops;the structure makes the flow field more stable allowed evenness of flow field tannin-based foaming precursor resin.The results reveal that it is beneficial for tannin-based foaming precursor resin to use an eggbeater with a speed of 1500 rpm to reduce the consumption of resources while obtaining a uniform flow field.

A functionalized activated carbon adsorbent prepared from waste amidoxime resin by modifying with H_(3)PO_(4) and ZnCl_(2) and its excellent Cr(Ⅵ)adsorption

With the application of resins in various fields, numerous waste resins that are difficult to treat have been produced. The industrial wastewater containing Cr(Ⅵ) has severely polluted soil and groundwater environments, thereby endangering human health. Therefore, in this paper, a novel functionalized mesoporous adsorbent PPR-Z was synthesized from waste amidoxime resin for adsorbing Cr(Ⅵ). The waste amidoxime resin was first modified with H3PO4 and ZnCl_(2), and subsequently, it was carbonized through slow thermal decomposition. The static adsorption of PPR-Z conforms to the pseudo-second-order kinetic model and Langmuir isotherm, indicating that the Cr(Ⅵ) adsorption by PPR-Z is mostly chemical adsorption and exhibits single-layer adsorption. The saturated adsorption capacity of the adsorbent for Cr(Ⅵ) could reach 255.86 mg/g. The adsorbent could effectively reduce Cr(Ⅵ) to Cr(Ⅲ) and decrease the toxicity of Cr(Ⅵ) during adsorption. PPR-Z exhibited Cr(Ⅵ) selectivity in electroplating wastewater. The main mechanisms involved in the Cr(Ⅵ) adsorption are the chemical reduction of Cr(Ⅵ) into Cr(Ⅲ) and electrostatic and coordination interactions. Preparation of PPR-Z not only solves the problem of waste resin treatment but also effectively controls Cr(Ⅵ) pollution and realizes the concept of “treating waste with waste”.

Modification of Nano-α-Al2O3 and Its Influence on the Surface Properties of Waterborne Polyurethane Resin Composite Passivation Films

Silane coupling agent KH560 was used to modify the surface of nano-α-Al2O3 in ethanol-aqueous solution with different proportions. The particle size of nano-α-Al2O3 was determined by nano-particle size analyzer, and the effects of nano-α-Al2O3 content, ethanol-aqueous solution ratio and KH560 dosage on the dispersion and particle size of nano-α-Al2O3 were investigated. The material structure before and after modification was determined by Fourier transform infrared spectroscopy (FTIR). Aqueous polyurethane resin and inorganic components are combined with modified nano-α-Al2O3 dispersion to form chromium-free passivation solution. The solution is coated on the galvanized sheet, the adhesion and surface hardness are tested, the bonding strength of the coating and the surface hardness of the substrate are discussed. The corrosion resistance and surface morphology of the matrix were investigated by electrochemical test, neutral salt spray test and scanning electron microscope test. The chromium-free passivation film formed after the modification of nano-α-Al2O3 increases the surface hardness of galvanized sheet by about 85%. The corrosion resistance of the film is better than that of a single polyurethane film. The results show that the surface hardness and corrosion resistance of polyurethane resin composite passivation film are significantly improved by the introduction of nano-α-Al2O3.

Toray develops hybrid bonding insulating resin and revolutionary polymer membrane

This year,Toray Industries,Inc.,announced that it has developed an insulating resin material for hybrid bonding(micro bonding).The material is based on Semicofine™and Photoneece™.These are high-heat-resistant polyimide coatings for semiconductor and display devices.The new material combines a conventional polyimide coating agent with the company’s processing and bonding technologies.It can enhance the yields and reliability of semiconductor devices in the hybrid bonding process,which entails bonding semiconductor chips with metal electrodes.Toray will push ahead with prototyping and providing samples to customers.It aims to obtain materials certification in 2025 and start mass production by 2028.

Micromechanical interlocking structure at the filler/resin interface for dental composites: a review

Dental resin composites(DRCs)are popular materials for repairing caries or dental defect,requiring excellent properties to cope with the complex oral environment.Filler/resin interface interaction has a significant impact on the physicochemical/biological properties and service life of DRCs.

A novel high-efficient P/N/Si-containing APP-based flame retardant with a silane coupling agent in its molecular structure for epoxy resin

A flame retardant containing multiple antiflaming elements usually exhibits high-efficient flame retardancy. Here, a novel P/N/Si-containing ammonium polyphosphate derivative(APTES-APP) is synthesized from ammonium polyphosphate(APP) and silane coupling agent(3-aminopropyl)triethoxysilane(APTES)via cation exchange, which is quite different in the chemical structure from APTES-modified APP for retaining silicon hydroxyls. APTES-APP is highly efficient for the epoxy resin. 8%(mass) APTES-APP imparts excellent flame retardancy to the epoxy resin, with a V-0 rating at the UL-94 test(1.6 mm)and an LOI value of 26%(vol). The peak heat release rate and total smoke production of the flameretardant epoxy resin are decreased by 68.1% and 31.3%, respectively. The synergy of P/N/Si contributes to the well-expanded char residue with a strong and dense surface layer, which is a very good barrier against heat and mass transfer. Besides, there is no significant deterioration in the mechanical properties of flame-retardant epoxy resin thanks to silicon hydroxyls forming hydrogen bonds with epoxy molecules. Meanwhile, other molecules can be grafted onto APTES-APP via these silicon hydroxyls, if needed.Briefly, this work has developed a new strategy for amino silane as flame retardants. In conjunction with a low-cost and simple preparation method, APTES-APP has a promising prospect in the high-performance flame-retardant epoxy.

Resin composition: An indicator of oil maturity as revealed by fourier transform ion cyclotron resonance mass spectrometry

A pyrolysis experiment was carried out on a Dongying Depression kerogen sample to separate the resin from the oil. Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) with a positive-ion detector was used to detect the relative proportional changes in the compounds of the resin. During the whole pyrolysis experiment, the relative ratio of resin exceed 10% of the soluble component at each temperature point. Five compounds were detected from the resin: N1, N1O1, N1O_(2), O1, and O_(2). To research the changes in the proportions of the compounds during pyrolysis clearly, these five compounds were divided into three classes: N1, N1Ox, and Ox. The N1 class has the largest proportion in resin at the beginning of the pyrolysis, while Ox class has the least proportion. And the relationship between the number and the molecular mass of three classes compound was researched. With increasing maturity, the proportion of N1 and the N1Ox class decreased rapidly, while the Ox class increased slowly. Through researching these resin compounds, it was found that an inversion in the proportions of above three compounds appeared at the end of the oil window. At the same time, we found that the DBE and carbon number of resin compounds have changed obviously during the pyrolysis: the DBE increased, while the carbon number decreased significantly. And the details of the change of each compound have been researched. This research extends our knowledge of judging the maturity of crude oil during the pyrolysis through the characteristics of compounds in resin and provides the new index based on resin for the evaluation of thermal evolution stage and hydrocarbon generation capacity of source rocks.