This manuscript explores the behavior of a junctionless tri-gate FinFET at the nano-scale region using SiGe material for the channel.For the analysis,three different channel structures are used:(a)tri-layer stack chan...This manuscript explores the behavior of a junctionless tri-gate FinFET at the nano-scale region using SiGe material for the channel.For the analysis,three different channel structures are used:(a)tri-layer stack channel(TLSC)(Si-SiGe-Si),(b)double layer stack channel(DLSC)(SiGe-Si),(c)single layer channel(SLC)(S_(i)).The I−V characteristics,subthreshold swing(SS),drain-induced barrier lowering(DIBL),threshold voltage(V_(t)),drain current(ION),OFF current(IOFF),and ON-OFF current ratio(ION/IOFF)are observed for the structures at a 20 nm gate length.It is seen that TLSC provides 21.3%and 14.3%more ON current than DLSC and SLC,respectively.The paper also explores the analog and RF factors such as input transconductance(g_(m)),output transconductance(gds),gain(gm/gds),transconductance generation factor(TGF),cut-off frequency(f_(T)),maximum oscillation frequency(f_(max)),gain frequency product(GFP)and linearity performance parameters such as second and third-order harmonics(g_(m2),g_(m3)),voltage intercept points(VIP_(2),VIP_(3))and 1-dB compression points for the three structures.The results show that the TLSC has a high analog performance due to more gm and provides 16.3%,48.4%more gain than SLC and DLSC,respectively and it also provides better linearity.All the results are obtained using the VisualTCAD tool.展开更多
The China initiative Accelerator Driven System,CiADS,physics design adopts 162.5 MHz,325 MHz,and 650 MHz cavities,which are driven by the corresponding radio frequency(RF)power system,requiring frequency translation f...The China initiative Accelerator Driven System,CiADS,physics design adopts 162.5 MHz,325 MHz,and 650 MHz cavities,which are driven by the corresponding radio frequency(RF)power system,requiring frequency translation front-end for the RF station.For that application,a general-purpose design front-end prototype has been developed to evaluate the multi-frequency point supported design feasibility.The difficult parts to achieve the requirements of the general-purpose design are reasonable device selection and balanced design.With a carefully selected low-noise wide-band RF mixer and amplifier to balance the performance of multi-frequency supported down-conversion,specially designed LO distribution net to increase isolation between adjacent channels,and external band-pass filter to realize expected up-conversion frequencies,high maintenance and modular front-end generalpurpose design has been implemented.Results of standard parameters show an R2 value of at least 99.991%in the range of-60-10 dBm for linearity,up to 18 dBm for P1dB,and up to 89 dBc for cross talk between adjacent channels.The phase noise spectrum is lower than 80 dBc in the range of 0-1 MHz;cumulative phase noise is 0.006°;and amplitude and phase stability are 0.022%and 0.034°,respectively.展开更多
A new T-shaped tunnel field-effect transistor(TTFET) with gate dielectric spacer(GDS) structure is proposed in this paper. To further studied the effects of GDS structure on the TTFET, detailed device characteristics ...A new T-shaped tunnel field-effect transistor(TTFET) with gate dielectric spacer(GDS) structure is proposed in this paper. To further studied the effects of GDS structure on the TTFET, detailed device characteristics such as current-voltage relationships, energy band diagrams, band-to-band tunneling(BTBT) rate and the magnitude of the electric field are investigated by using TCAD simulation. It is found that compared with conventional TTFET and TTFET with gate-drain overlap(GDO) structure, GDS-TTFET not only has the minimum ambipolar current but also can suppress the ambipolar current under a more extensive bias range. Furthermore, the analog/RF performances of GDS-TTFET are also investigated in terms of transconductance, gate-source capacitance, gate-drain capacitance, cutoff frequency, and gain bandwidth production. By inserting a low-κ spacer layer between the gate electrode and the gate dielectric, the GDS structure can effectively reduce parasitic capacitances between the gate and the source/drain, which leads to better performance in term of cutoff frequency and gain bandwidth production. Finally, the thickness of the gate dielectric spacer is optimized for better ambipolar current suppression and improved analog/RF performance.展开更多
In the first editorial of this two-part special issue, we pointed out that one of the biggest trends in wireless broadband, radar, sonar, and broadcasting technology is software RF processing and digital front-end [1]...In the first editorial of this two-part special issue, we pointed out that one of the biggest trends in wireless broadband, radar, sonar, and broadcasting technology is software RF processing and digital front-end [1]. Thistrend encompasses signal processing algorithms and integrated circuit design and includes digital pre-distortion (DPD), conversions between digital and analog signals, digita up-conversion (DUC), digital down-conversion (DDC), DC offset,展开更多
One of the biggest technology trends in wireless broadband, radar, sonar, and broadcasting systems is software radio frequency processing and digital front-end. This trend encompasses a broad range of topics, from ci...One of the biggest technology trends in wireless broadband, radar, sonar, and broadcasting systems is software radio frequency processing and digital front-end. This trend encompasses a broad range of topics, from circuit design and signal processing to system integration. It includes digital up-conversion (DUC) and down-conversion (DDC), digital predistortion (DPD),展开更多
Ultrasonic testing systems have been extensively used in medical imaging and non-destructive testing applications. Generally, these systems aim at a particular application or target material. To make these systems por...Ultrasonic testing systems have been extensively used in medical imaging and non-destructive testing applications. Generally, these systems aim at a particular application or target material. To make these systems portable and more adaptable to the test environments, this study presents a reconfigurable ultrasonic testing system (RUTS), which possesses dynamic reconfiguration capabilities. RUTS consists a fully programmable Analog Front-End (AFE), which facilitates beamforming and signal conditioning for variety of applications. RUTS AFE supports up to 8 transducers for phased-array implementation. Xilinx Zynq System-on-Chip (SoC) based Zedboard provides the back-end processing of RUTS. The powerful ARM embedded processor available within Zynq SoC manages the ultrasonic data acquisition/processing and overall system control, which makes RUTS a unique platform for the ultrasonic researchers to experiment and evaluate a wide range of real-time ultrasonic signal processing applications. This Linux-based system is utilized for ultra-sonic data compression implementation providing a versatile environment for further development of ultrasonic imaging and testing system. Furthermore, this study demonstrates the capabilities of RUTS by performing ultrasonic data acquisition and data compression in real-time. Thus, this reconfigurable system enables ultrasonic designers and researchers to efficiently prototype different experiments and to incorporate and analyze high performance ultrasonic signal and image processing algorithms.展开更多
为了提高超高频RFID系统中阅读器在低信噪比的情况下仍具有较高的识别能力,提出一种基于FPGA系统结合软件无线电方法实现超高频RFID射频前端电路方案。超高频射频识别系统必须符合EPC Class 1generation 2标准,所设计的电路系统以Xilin...为了提高超高频RFID系统中阅读器在低信噪比的情况下仍具有较高的识别能力,提出一种基于FPGA系统结合软件无线电方法实现超高频RFID射频前端电路方案。超高频射频识别系统必须符合EPC Class 1generation 2标准,所设计的电路系统以Xilinx公司的XC6SLX16-2CSG324FPGA芯片为硬件基础,将数字基带调制解调和中频滤波电路在FPGA系统中设计实现,重点阐述了射频前端电路的设计结构、AD/DA转换电路,以及数字滤波器的设计。实验结果表明,所设计的超高频RFID阅读器简化了前端电路系统结构,提升了稳定性,增强了抗干扰能力。该电路系统在信噪比较低的情况下,能够较好地实现915MHz频率的射频接收和发送。展开更多
An adjustable mixer for surface acoustic wave( SAW)-less radio frequency( RF) front-end is presented in this paper. Through changing the bias voltage,the presented mixer with reconfigurable voltage conversion gain( VC...An adjustable mixer for surface acoustic wave( SAW)-less radio frequency( RF) front-end is presented in this paper. Through changing the bias voltage,the presented mixer with reconfigurable voltage conversion gain( VCG) is suitable for multi-mode multi-standard( MMMS) applications. An equivalent local oscillator( LO) frequency-tunable high-Q band-pass filter( BPF) at low noise amplifier( LNA) output is used to reject the out-of-band interference signals. Base-band( BB) capacitor of the mixer is variable to obtain 15 kinds of intermediate frequency( IF) bandwidth( BW). The proposed passive mixer with LNA is implemented in TSMC 0. 18μm RF CMOS process and operates from 0. 5 to 2. 5 GHz with measured maximum out-of-band rejection larger than 40 d B. The measured VCG of the front-end can be changed from 5 to 17 d B; the maximum input intercept point( IIP3) is0 d Bm and the minimum noise figure( NF) is 3. 7 d B. The chip occupies an area of 0. 44 mm^2 including pads.展开更多
随着工艺尺寸的不断缩小,电路规模的不断复杂化以及版图中寄生规模的不断增大,在一些大规模的后仿验证过程中,Cadence公司提供的模拟全精度仿真器Spectre/APS/APS RF已不能满足需求。针对这一问题,Cadence于2019年推出APS的下一代模拟...随着工艺尺寸的不断缩小,电路规模的不断复杂化以及版图中寄生规模的不断增大,在一些大规模的后仿验证过程中,Cadence公司提供的模拟全精度仿真器Spectre/APS/APS RF已不能满足需求。针对这一问题,Cadence于2019年推出APS的下一代模拟全精度仿真器Spectre X,在实际使用过程中发现其对普通模拟仿真性能提升明显并且基本保持了APS的仿真精度。2020年,Cadence推出其APS RF的下一代仿真器Spectre X RF仿真器。RF仿真在整体仿真验证流程中同样占据很大一部分,在将其应用到实际项目前,需要与APS RF对比其性能和速度。介绍了Spectre X RF的用法,并重点介绍在几种采用不同工艺的RFIC设计中,仿真器Spectre APS RF与Spectre X RF仿真性能与精度的对比情况。展开更多
In this paper, we propose multi-fin FET design techniques targeted for RF applications. Overlap and underlap design configuration in a base FinFET are compared first and then multi-fin device (consisting of transistor...In this paper, we propose multi-fin FET design techniques targeted for RF applications. Overlap and underlap design configuration in a base FinFET are compared first and then multi-fin device (consisting of transistor unit up to 50) is studied to develop design limitations and to evaluate their effects on the device performance. We have also investigated the impact of the number of fins (up to 50) in multi-fin structure and resulting RF parameters. Our results show that as the number of fin increases, underlap design compromises RF performance and short channel effects. The results provide technical understanding that is necessary to realize new opportunities for RF and analog mixed-signal design with nanoscale FinFETs.展开更多
Here we review two 300℃metal–oxide(MO)thin-film transistor(TFT)technologies for the implementation of flexible electronic circuits and systems.Fluorination-enhanced TFTs for suppressing the variation and shift of tu...Here we review two 300℃metal–oxide(MO)thin-film transistor(TFT)technologies for the implementation of flexible electronic circuits and systems.Fluorination-enhanced TFTs for suppressing the variation and shift of turn-on voltage(VON),and dual-gate TFTs for acquiring sensor signals and modulating VON have been deployed to improve the robustness and performance of the systems in which they are deployed.Digital circuit building blocks based on fluorinated TFTs have been designed,fabricated,and characterized,which demonstrate the utility of the proposed low-temperature TFT technologies for implementing flexible electronic systems.The construction and characterization of an analog front-end system for the acquisition of bio-potential signals and an active-matrix sensor array for the acquisition of tactile images have been reported recently.展开更多
文摘This manuscript explores the behavior of a junctionless tri-gate FinFET at the nano-scale region using SiGe material for the channel.For the analysis,three different channel structures are used:(a)tri-layer stack channel(TLSC)(Si-SiGe-Si),(b)double layer stack channel(DLSC)(SiGe-Si),(c)single layer channel(SLC)(S_(i)).The I−V characteristics,subthreshold swing(SS),drain-induced barrier lowering(DIBL),threshold voltage(V_(t)),drain current(ION),OFF current(IOFF),and ON-OFF current ratio(ION/IOFF)are observed for the structures at a 20 nm gate length.It is seen that TLSC provides 21.3%and 14.3%more ON current than DLSC and SLC,respectively.The paper also explores the analog and RF factors such as input transconductance(g_(m)),output transconductance(gds),gain(gm/gds),transconductance generation factor(TGF),cut-off frequency(f_(T)),maximum oscillation frequency(f_(max)),gain frequency product(GFP)and linearity performance parameters such as second and third-order harmonics(g_(m2),g_(m3)),voltage intercept points(VIP_(2),VIP_(3))and 1-dB compression points for the three structures.The results show that the TLSC has a high analog performance due to more gm and provides 16.3%,48.4%more gain than SLC and DLSC,respectively and it also provides better linearity.All the results are obtained using the VisualTCAD tool.
文摘The China initiative Accelerator Driven System,CiADS,physics design adopts 162.5 MHz,325 MHz,and 650 MHz cavities,which are driven by the corresponding radio frequency(RF)power system,requiring frequency translation front-end for the RF station.For that application,a general-purpose design front-end prototype has been developed to evaluate the multi-frequency point supported design feasibility.The difficult parts to achieve the requirements of the general-purpose design are reasonable device selection and balanced design.With a carefully selected low-noise wide-band RF mixer and amplifier to balance the performance of multi-frequency supported down-conversion,specially designed LO distribution net to increase isolation between adjacent channels,and external band-pass filter to realize expected up-conversion frequencies,high maintenance and modular front-end generalpurpose design has been implemented.Results of standard parameters show an R2 value of at least 99.991%in the range of-60-10 dBm for linearity,up to 18 dBm for P1dB,and up to 89 dBc for cross talk between adjacent channels.The phase noise spectrum is lower than 80 dBc in the range of 0-1 MHz;cumulative phase noise is 0.006°;and amplitude and phase stability are 0.022%and 0.034°,respectively.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61306116 and 61472322)
文摘A new T-shaped tunnel field-effect transistor(TTFET) with gate dielectric spacer(GDS) structure is proposed in this paper. To further studied the effects of GDS structure on the TTFET, detailed device characteristics such as current-voltage relationships, energy band diagrams, band-to-band tunneling(BTBT) rate and the magnitude of the electric field are investigated by using TCAD simulation. It is found that compared with conventional TTFET and TTFET with gate-drain overlap(GDO) structure, GDS-TTFET not only has the minimum ambipolar current but also can suppress the ambipolar current under a more extensive bias range. Furthermore, the analog/RF performances of GDS-TTFET are also investigated in terms of transconductance, gate-source capacitance, gate-drain capacitance, cutoff frequency, and gain bandwidth production. By inserting a low-κ spacer layer between the gate electrode and the gate dielectric, the GDS structure can effectively reduce parasitic capacitances between the gate and the source/drain, which leads to better performance in term of cutoff frequency and gain bandwidth production. Finally, the thickness of the gate dielectric spacer is optimized for better ambipolar current suppression and improved analog/RF performance.
文摘In the first editorial of this two-part special issue, we pointed out that one of the biggest trends in wireless broadband, radar, sonar, and broadcasting technology is software RF processing and digital front-end [1]. Thistrend encompasses signal processing algorithms and integrated circuit design and includes digital pre-distortion (DPD), conversions between digital and analog signals, digita up-conversion (DUC), digital down-conversion (DDC), DC offset,
文摘One of the biggest technology trends in wireless broadband, radar, sonar, and broadcasting systems is software radio frequency processing and digital front-end. This trend encompasses a broad range of topics, from circuit design and signal processing to system integration. It includes digital up-conversion (DUC) and down-conversion (DDC), digital predistortion (DPD),
文摘Ultrasonic testing systems have been extensively used in medical imaging and non-destructive testing applications. Generally, these systems aim at a particular application or target material. To make these systems portable and more adaptable to the test environments, this study presents a reconfigurable ultrasonic testing system (RUTS), which possesses dynamic reconfiguration capabilities. RUTS consists a fully programmable Analog Front-End (AFE), which facilitates beamforming and signal conditioning for variety of applications. RUTS AFE supports up to 8 transducers for phased-array implementation. Xilinx Zynq System-on-Chip (SoC) based Zedboard provides the back-end processing of RUTS. The powerful ARM embedded processor available within Zynq SoC manages the ultrasonic data acquisition/processing and overall system control, which makes RUTS a unique platform for the ultrasonic researchers to experiment and evaluate a wide range of real-time ultrasonic signal processing applications. This Linux-based system is utilized for ultra-sonic data compression implementation providing a versatile environment for further development of ultrasonic imaging and testing system. Furthermore, this study demonstrates the capabilities of RUTS by performing ultrasonic data acquisition and data compression in real-time. Thus, this reconfigurable system enables ultrasonic designers and researchers to efficiently prototype different experiments and to incorporate and analyze high performance ultrasonic signal and image processing algorithms.
文摘为了提高超高频RFID系统中阅读器在低信噪比的情况下仍具有较高的识别能力,提出一种基于FPGA系统结合软件无线电方法实现超高频RFID射频前端电路方案。超高频射频识别系统必须符合EPC Class 1generation 2标准,所设计的电路系统以Xilinx公司的XC6SLX16-2CSG324FPGA芯片为硬件基础,将数字基带调制解调和中频滤波电路在FPGA系统中设计实现,重点阐述了射频前端电路的设计结构、AD/DA转换电路,以及数字滤波器的设计。实验结果表明,所设计的超高频RFID阅读器简化了前端电路系统结构,提升了稳定性,增强了抗干扰能力。该电路系统在信噪比较低的情况下,能够较好地实现915MHz频率的射频接收和发送。
基金Supported by the National Basic Research Program of China(No.2010CB327404)the Priority Academic Program Development of Jiangsu Higher Education Institutions
文摘An adjustable mixer for surface acoustic wave( SAW)-less radio frequency( RF) front-end is presented in this paper. Through changing the bias voltage,the presented mixer with reconfigurable voltage conversion gain( VCG) is suitable for multi-mode multi-standard( MMMS) applications. An equivalent local oscillator( LO) frequency-tunable high-Q band-pass filter( BPF) at low noise amplifier( LNA) output is used to reject the out-of-band interference signals. Base-band( BB) capacitor of the mixer is variable to obtain 15 kinds of intermediate frequency( IF) bandwidth( BW). The proposed passive mixer with LNA is implemented in TSMC 0. 18μm RF CMOS process and operates from 0. 5 to 2. 5 GHz with measured maximum out-of-band rejection larger than 40 d B. The measured VCG of the front-end can be changed from 5 to 17 d B; the maximum input intercept point( IIP3) is0 d Bm and the minimum noise figure( NF) is 3. 7 d B. The chip occupies an area of 0. 44 mm^2 including pads.
文摘随着工艺尺寸的不断缩小,电路规模的不断复杂化以及版图中寄生规模的不断增大,在一些大规模的后仿验证过程中,Cadence公司提供的模拟全精度仿真器Spectre/APS/APS RF已不能满足需求。针对这一问题,Cadence于2019年推出APS的下一代模拟全精度仿真器Spectre X,在实际使用过程中发现其对普通模拟仿真性能提升明显并且基本保持了APS的仿真精度。2020年,Cadence推出其APS RF的下一代仿真器Spectre X RF仿真器。RF仿真在整体仿真验证流程中同样占据很大一部分,在将其应用到实际项目前,需要与APS RF对比其性能和速度。介绍了Spectre X RF的用法,并重点介绍在几种采用不同工艺的RFIC设计中,仿真器Spectre APS RF与Spectre X RF仿真性能与精度的对比情况。
文摘In this paper, we propose multi-fin FET design techniques targeted for RF applications. Overlap and underlap design configuration in a base FinFET are compared first and then multi-fin device (consisting of transistor unit up to 50) is studied to develop design limitations and to evaluate their effects on the device performance. We have also investigated the impact of the number of fins (up to 50) in multi-fin structure and resulting RF parameters. Our results show that as the number of fin increases, underlap design compromises RF performance and short channel effects. The results provide technical understanding that is necessary to realize new opportunities for RF and analog mixed-signal design with nanoscale FinFETs.
基金supported by Grant RGC 16215720 from the Science and Technology Program of Shenzhen under JCYJ20200109140601691Grant GHP/018/21SZ from the Innovation and Technology Fund+1 种基金Grant SGDX20211123145404006 from the Science and Technology Program of ShenzhenFundamental and Applied Fundamental Research Fund of Guangdong Province 2021B1515130001。
文摘Here we review two 300℃metal–oxide(MO)thin-film transistor(TFT)technologies for the implementation of flexible electronic circuits and systems.Fluorination-enhanced TFTs for suppressing the variation and shift of turn-on voltage(VON),and dual-gate TFTs for acquiring sensor signals and modulating VON have been deployed to improve the robustness and performance of the systems in which they are deployed.Digital circuit building blocks based on fluorinated TFTs have been designed,fabricated,and characterized,which demonstrate the utility of the proposed low-temperature TFT technologies for implementing flexible electronic systems.The construction and characterization of an analog front-end system for the acquisition of bio-potential signals and an active-matrix sensor array for the acquisition of tactile images have been reported recently.