This paper presents the design and implementation of a fully integrated multi-band RF receiver frontend for GNSS applications on L-band.A single RF signal channel with a low-IF architecture is adopted for multi-band o...This paper presents the design and implementation of a fully integrated multi-band RF receiver frontend for GNSS applications on L-band.A single RF signal channel with a low-IF architecture is adopted for multi-band operation on the RF section,which mainly consists of a low noise amplifier（LNA）,a down-converter,polyphase filters and summing circuits.An improved cascode source degenerated LNA with a multi-band shared off-chip matching network and band switches is implemented in the first amplifying stage.Also,a re-designed wideband double balance mixer is implemented in the down conversion stage,which provides better gain,noise figure and linearity performances.Using a TSMC 0.18μm 1P4M RF CMOS process,a compact 1.27 GHz/1.575 GHz dualband GNSS frontend is realized in the proposed low-IF topology.The measurements exhibit the gains of 45 dB and 43 dB,and noise figures are controlled at 3.35 dB and 3.9 dB of the two frequency bands,respectively.The frontend model consumes about 11.8-13.5 mA current on a 1.8 V power supply.The core occupies 1.91×0.53 mm2 while the total die area with ESD is 2.45×2.36 mm^2.展开更多
This paper presents an improved merged architecture for a low-IF GNSS receiver frontend,where the bias current and functions are reused in a stacked quadrature LNA-mixer-VCO.Only a single spiral inductor is implemente...This paper presents an improved merged architecture for a low-IF GNSS receiver frontend,where the bias current and functions are reused in a stacked quadrature LNA-mixer-VCO.Only a single spiral inductor is implemented for the LC resonator and an extra 1/2 frequency divider is added as the quadrature LO signal generator. The details of the design are presented.The gain plan and noise figure are discussed.The phase noise,quadrature accuracy and power consumption are improved.The test chip is fabricated though a 0.18μm RF CMOS process. The measured noise figure is 5.4 dB on average,with a gain of 43 dB and a IIP3 of-39 dBm.The measured phase noise is better than -105 dBc/Hz at 1 MHz offset.The total power consumption is 19.8 mW with a 1.8 V supply. The experimental results satisfy the requirements for GNSS applications.展开更多
This paper presents a dual-band low noise amplifier for the receiver of a global navigation satellite system. The differences between single band and multi-band design methods are discussed. The relevant parameter ana...This paper presents a dual-band low noise amplifier for the receiver of a global navigation satellite system. The differences between single band and multi-band design methods are discussed. The relevant parameter analysis and the details of circuit design are presented. The test chip was implemented in a TSMC 0.18 μm 1P4M RF CMOS process. The LNA achieves a gain of 16.8 dB/18.9 dB on 1.27 GHz/1.575 GHz. The measured noise figure is around 1.5-1.7 dB on both bands. The LNA consumes less than 4.3 mA of current from a 1.8 V power supply. The measurement results show consistency with the design. And the LNA can fully satisfy the demands of the GNSS receiver.展开更多
文摘This paper presents the design and implementation of a fully integrated multi-band RF receiver frontend for GNSS applications on L-band.A single RF signal channel with a low-IF architecture is adopted for multi-band operation on the RF section,which mainly consists of a low noise amplifier（LNA）,a down-converter,polyphase filters and summing circuits.An improved cascode source degenerated LNA with a multi-band shared off-chip matching network and band switches is implemented in the first amplifying stage.Also,a re-designed wideband double balance mixer is implemented in the down conversion stage,which provides better gain,noise figure and linearity performances.Using a TSMC 0.18μm 1P4M RF CMOS process,a compact 1.27 GHz/1.575 GHz dualband GNSS frontend is realized in the proposed low-IF topology.The measurements exhibit the gains of 45 dB and 43 dB,and noise figures are controlled at 3.35 dB and 3.9 dB of the two frequency bands,respectively.The frontend model consumes about 11.8-13.5 mA current on a 1.8 V power supply.The core occupies 1.91×0.53 mm2 while the total die area with ESD is 2.45×2.36 mm^2.
基金Project supported by the National Natural Science Foundation of China(No.61076101)
文摘This paper presents an improved merged architecture for a low-IF GNSS receiver frontend,where the bias current and functions are reused in a stacked quadrature LNA-mixer-VCO.Only a single spiral inductor is implemented for the LC resonator and an extra 1/2 frequency divider is added as the quadrature LO signal generator. The details of the design are presented.The gain plan and noise figure are discussed.The phase noise,quadrature accuracy and power consumption are improved.The test chip is fabricated though a 0.18μm RF CMOS process. The measured noise figure is 5.4 dB on average,with a gain of 43 dB and a IIP3 of-39 dBm.The measured phase noise is better than -105 dBc/Hz at 1 MHz offset.The total power consumption is 19.8 mW with a 1.8 V supply. The experimental results satisfy the requirements for GNSS applications.
文摘This paper presents a dual-band low noise amplifier for the receiver of a global navigation satellite system. The differences between single band and multi-band design methods are discussed. The relevant parameter analysis and the details of circuit design are presented. The test chip was implemented in a TSMC 0.18 μm 1P4M RF CMOS process. The LNA achieves a gain of 16.8 dB/18.9 dB on 1.27 GHz/1.575 GHz. The measured noise figure is around 1.5-1.7 dB on both bands. The LNA consumes less than 4.3 mA of current from a 1.8 V power supply. The measurement results show consistency with the design. And the LNA can fully satisfy the demands of the GNSS receiver.
