Power transfer efficiency in an air-breathing radio frequency ion thruster

Due to a series of challenges such as low-orbit maintenance of satellites, the air-breathing electric propulsion has got widespread attention. Commonly, the radio frequency ion thruster is favored by low-orbit missions due to its high specific impulse and efficiency. In this paper, the power transfer efficiency of the radio frequency ion thruster with different gas compositions is studied experimentally, which is obtained by measuring the radio frequency power and current of the antenna coil with and without discharge operation. The results show that increasing the turns of antenna coils can effectively improve the radio frequency power transfer efficiency, which is due to the improvement of Q factor. In pure N_2 discharge,with the increase of radio frequency power, the radio frequency power transfer efficiency first rises rapidly and then exhibits a less steep increasing trend. The radio frequency power transfer efficiency increases with the increase of gas pressure at relatively high power, while declines rapidly at relatively low power. In N_(2)/O_(2) discharge, increasing the N_(2) content at high power can improve the radio frequency power transfer efficiency, but the opposite was observed at low power. In order to give a better understanding of these trends, an analytic solution in limit cases is utilized, and a Langmuir probe was employed to measure the electron density. It is found that the evolution of radio frequency power transfer efficiency can be well explained by the variation of plasma resistance, which is related to the electron density and the effective electron collision frequency.

Experimental results of a magnetic field modification to the radio frequency driver of a negative ion source

A magnetic field produced by a current flowing through the plasma grid(PG) is one of the solutions to reduce the collisional loss of negative ions in a negative ion source, which reduces the electron temperature in front of the PG. However, the magnetic field diffused into the driver has some influence on the plasma outflowing. In order to investigate the effect of changing this magnetic field on the outflowing of plasma from the driver, a circular ring(absorber) of high permeability iron has been introduced at the driver exit, which can reduce the magnetic field around it and improve plasma outflowing. With the application of the absorber, the electron density is increased by about 35%, and the extraction current measured from the extraction grid is increased from 1.02 A to 1.29 A. The results of the extraction experiment with cesium injection show that both the extraction grid(EG) current and H-current are increased when the absorber is introduced.

Hollow cathode effect in radio frequency hollow electrode discharge in argon

Radio frequency capacitively coupled plasma source(RF-CCP)with a hollow electrode can increase the electron density through the hollow cathode effect(HCE),which offers a method to modify the spatial profiles of the plasma density.In this work,the variations of the HCE in one RF period are investigated by using a two-dimensional particle-in-cell/Monte-Carlo collision(PIC/MCC)model.The results show that the sheath electric field,the sheath potential drop,the sheath thickness,the radial plasma bulk width,the electron energy distribution function(EEDF),and the average electron energy in the cavity vary in one RF period.During the hollow electrode sheath's expansion phase,the secondary electron heating and sheath oscillation heating in the cavity are gradually enhanced,and the frequency of the electron pendular motion in the cavity gradually increases,hence the HCE is gradually enhanced.However,during the hollow electrode sheath's collapse phase,the secondary electron heating is gradually attenuated.In addition,when interacting with the gradually collapsed hollow electrode sheaths,high-energy plasma bulk electrons in the cavity will lose some energy.Furthermore,the frequency of the electron pendular motion in the cavity gradually decreases.Therefore,during the hollow electrode sheath's collapse phase,the HCE is gradually attenuated.

Performance of a 4 cm iodine-fueled radio frequency ion thruster

The performance of an iodine radio ion thruster with a 4 cm diameter(IRIT4)was studied experimentally in this paper.Regulation of the mass flow rates of the iodine propellant is achieved by using a temperature control method of the iodine reservoir.Performance of the thruster using iodine as propellants is obtained at different total thruster powers of 40.6–128.8 W,different grid voltages of 1000–1800 V and the iodine flow rate of 100μgs^(-1).Results show that thrust and specific impulse increase approximately linearly with the increasing total thruster power and the screen grid voltage.The thrust of 2.32 mN and the specific impulse of 2361 s are obtained at the nominal total thruster power of 95.8 W and the screen grid voltage of 1800 V.It is also indicated that performance of the iodine propellant is comparable to that of the xenon propellant;and a difference between them is that the iodine thrust is slightly higher than xenon when the total thruster power is more than 62 W.At the nominal 95.8 W total thruster power,the thrust values of them are 2.32 m N and 2.15 mN respectively,and the thrust-to-power ratios of them are 24.2 mN kW^(-1)and 23.5 mN kW^(-1),respectively.

Application of Radio Frequency Identification (RFID) in Dairy Information Management

As a kind of brand-new technology, radio frequency identification management, data control and acquisition. This paper introduced food safety system construction, analyzed the advantages and problems in dairy modem suggestions for solution according to the practical situation. （RFID） plays an important role in dairy information tracing and culture function extension of managing breeding technology, and finally put forward some

Influence of anode temperature on ignition performance of the IRIT4-2D iodine-fueled radio frequency ion thruster

This paper reports the ignition performance of the iodine-fueled radio frequency(RF)ion thruster(IRIT)at different anode temperaturesT_(a0).The experimental results show that the anode temperature plays important role on the ignition process of the IRIT.There were two characteristic temperatures related to the anode:the minimum ignition temperatureT_(i0)and the stable ignition temperatureT_(is),which were much lower than the pipeline temperature and the storage tank temperature.AtT_(a0)<T_(i0),it failed to discharge.WhenT_(i0)≤T_(a0)<T_(is),it was ignited with dramatical oscillations.AtT_(a0)≥T_(is),the discharge was stable in a large anode temperature range.The analysis showed that the different discharge phenomena at different anode temperatures were attributed to the change of iodine flow rate during the process of the iodine deposition-clogging and sublimation-clearing inside the thruster.The research helps improve the preheating design of the iodine-fueled electric thruster.

Electrical and thermal characterization of near-surface electrical discharge plasma actuation driven by radio frequency voltage at low pressure

The electrical and thermal characterization of near-surface electrical discharge plasma driven by radio frequency voltage are investigated experimentally in this paper. The influences of operating pressure, electrode distance, and duty cycle on the discharge are studied. When pressure reaches 60 Ton. （1 Torr= 1.33322 x 102 Pa） the transition from diffuse glow mode to constricted mode occurs. With the operating pressure varying from 10 Tort to 60 Torr, the discharge energy calculated from the charge-voltage （Q-V） Lissajous figure decreases rapidly, while it remains unchanged between 60 Torr and 460 Torr. Under certain experimental conditions, there exists an optimized electrode distance （8 mm）. As the duty cycle of applied voltage increases, the voltage-current waveforms and Q-V Lissajous figures show no distinct changes.

Thermal and induced flow characteristics of radio frequency surface dielectric barrier discharge plasma actuation at atmospheric pressure

Thermal and induced flow velocity characteristics of radio frequency（RF） surface dielectric barrier discharge（SDBD）plasma actuation are experimentally investigated in this paper. The spatial and temporal distributions of the dielectric surface temperature are measured with the infrared thermography at atmospheric pressure. In the spanwise direction, the highest dielectric surface temperature is acquired at the center of the high voltage electrode, while it reduces gradually along the chordwise direction. The maximum temperature of the dielectric surface raises rapidly once discharge begins.After several seconds（typically 100 s）, the temperature reaches equilibrium among the actuator＇s surface, plasma, and surrounding air. The maximum dielectric surface temperature is higher than that powered by an AC power supply in dozens of k Hz. Influences of the duty cycle and the input frequency on the thermal characteristics are analyzed. When the duty cycle increases, the maximum dielectric surface temperature increases linearly. However, the maximum dielectric surface temperature increases nonlinearly when the input frequency varies from 0.47 MHz to 1.61 MHz. The induced flow velocity of the RF SDBD actuator is 0.25 m/s.

Fabrication and properties of high performance YBa_2Cu_3O_(7-δ) radio frequency SQUIDs with step-edge Josephson junctions

We describe the fabrication of high performance YBa2Cu3O7-δ （YBCO） radio frequency （RF） superconducting quantum interference devices （SQUIDs）, which were prepared on 5 mm×5 mm LaAlO3 （LAO） substrates by employing stepedge junctions （SEJs） and in flip-chip configuration with 12 mm×12 mm resonators. The step in the substrate was produced by Ar ion etching with step angles ranging from 47° to 61°, which is steep enough to ensure the formation of grain boundaries （GBs） at the step edges. The YBCO film was deposited using the pulsed laser deposition （PLD） technique with a film thickness half of the height of the substrate step. The inductance of the SQUID washer was designed to be about 157 pH. Under these circumstances, high performance YBCO RF SQUIDs were successfully fabricated with a typical flux-voltage transfer ratio of 83 mV/φ0, a white flux noise of 29 μφ0/√Hz, and the magnetic field sensitivity as high as 80 fT/√Hz. These devices have been applied in magnetocardiography and geological surveys.

Surface modification of silicone rubber by CF4 radio frequency capacitively coupled plasma for improvement of flashover

The flashover performance of insulating materials plays an important role in the development of high-voltage insulation systems.In this paper,silicone rubber(SIR)is modified by CF4 radio frequency capacitively coupled plasma(CCP)for the improvement of surface insulation performance.The discharge mode and active particles of CCP are diagnosed by the digital single-lens reflex and the spectrometer.Scanning electron microscopy and x-ray photoelectron spectroscopy are used for the surface physicochemical properties of samples,while the surface charge dissipation,charge accumulation measurement,and flashover test are applied for the surface electrical characteristics.Experimental results show that the fluorocarbon groups can be grafted and the surface roughness increases after plasma treatment.Besides,the surface charge dissipation is decelerated and the positive charge accumulation is inhibited obviously for the treated samples.Furthermore,the surface flashover voltage can be increased by 26.67%after 10 min of treatment.It is considered that strong electron affinity of C–F and increased surface roughness can contribute to deepening surface traps,which not only inhibits the development of secondary electron emission avalanche but also alleviates the surface charge accumulation and finally improves the surface flashover voltage of SIR.

Effective Treatment of Atrophic and Icepick Acne Scars Using Deep Non-Ablative Radiofrequency and Multisource Fractional RF Skin Resurfacing

Background and Objectives: Effective treatment for atrophic (depressed) and icepick acne scars requires treatment of both epidermis—for roughness, texture and hyperpigmentation, and the dermis—for collagen remodeling. All first generation radiofrequency systems allow nonablative RF treatment while a few others allow simple bipolar Fractional RF skin resurfacing. The FDA cleared multisource radiofrequency therapy system (EndyMed PRO, EndyMed Ltd., Cesarea, Israel) allows, for the first time, phase controlled multisource RF for both deep (up to 11 mm) non ablative RF and fractional RF skin resurfacing on the same treatment device. Study Design/Materials and Methods: Ten subjects with atrophic acne scars were enrolled in the study. Patients were photographed using standardized methods. In each treatment session, each patient received a full face 3DEEP non ablative skin tightening treatment followed by a Fractional skin resurfacing treatment. The treatment sessions were repeated once a month to a total of up to 4 treatments. Results: All subjects experienced mild-moderate edema and erythema as an immediate response to treatment. Edema resolved after up to three hours post treatment and erythema lasted up to 2 days. Micro ablative crusts were formed 1 - 2 days post treatments and lasted up to 5 days on facial areas. Patients' photographs—before each treatment session and 1 and 3 months after the last session—were graded according to the accepted Cosmetic Improvement Scale. All patients obtained significant skin improvement. Seventy percent of patients had 50% - 75% improvement one month after the third treatment session while the other thirty percent experienced a 25% - 50%. Discussion and Conclusions: The presented results describe for the first time a new treatment system (EndyMed PROTM) that allows both deep non ablative RF delivery and Fractional skin resurfacing on the same treatment platform. This work shows the synergy of combining these two applications for the improvement of acne scars, as well as for some secondary possible pigmentation and vascular improvement.

Germanium nanoislands grown by radio frequency magnetron sputtering: Annealing time dependent surface morphology and photoluminescence

Structural and optical properties of ～ 20 nm Ge nanoislands grown on Si（100） by radio frequency （rI） magnetron sputtering under varying annealing conditions are reported. Rapid thermal annealing at a temperature of 600 ℃ for 30 s, 90 s, and 120 s are performed to examine the influence of annealing time on the surface morphology and photoluminescence properties. X-ray diffraction spectra reveal prominent Ge and GeO2 peaks highly sensitive to the annealing time. Atomic force microscope micrographs of the as-grown sample show pyramidal nanoislands with relatively high-density （～ 10^11 cm^-2）. The nanoislands become dome-shaped upon annealing through a coarsening process mediated by Oswald ripening. The room temperature photoluminescence peaks for both as-grown （～ 3.29 eV） and annealed （～ 3.19 eV） samples consist of high intensity and broad emission, attributed to the effect of quantum confinement. The red shift （～ 0.10 eV） of the emission peak is attributed to the change in the size of the Ge nanoislands caused by annealing. Our easy fabrication method may contribute to the development of Ge nanostructure-based optoelectronics.

PERFORMANCE ANALYSIS OF FREQUENCY HOPPING PACKET RADIO NETWORK WITH ACKNOLEDGEMENT TRAFFIC

Performance analysis of an asynchronous frequency hopping packet radio network and numerical results are given. The network has mixed traffic, one type of packet needs an Acknowledgement(Ack), the other type does not need, the background of such a network is tactical missile systems. A reasonable network model is given, based on which the effect of various parameters under multiaccess interference is investigated. The performance curves of throughput and average packet delay is given in this paper.

Electrical and optical characteristics of the radio frequency surface dielectric barrier discharge plasma actuation

Electrical characteristics and optical emission spectrum of the radio frequency （RF） surface dielectric barrier discharge （SDBD） plasma actuation are investigated experimentally in this paper. Influences of operating pressure, duty cycle and load power on the discharge are analyzed. When the operating pressure reaches 30 kPa, the discharge energy calculated from the Charge-Voltage （Q-V） Lissajous figure increases significantly, while the effective capacitance decreases remarkably. As the duty cycle of the applied voltage increases, the voltage-current waveforms, the area of Q-V loop and the capacity show no distinct changes. Below 40 W, effective capacitance increases with the increase of load power, but it almost remains . peak peak unchanged when load power is between 40 W and 95 W. The relative intensity Ipeak 91.4/Ipeak380.5 changes little as the operating pressure varies from 4 kPa to 100 kPa, while it rises evidently with the pressure below 4 kPa, which indicates that the RF discharge mode shifts from filamentary discharge to glow discharge at around 4 kPa. With the increase of load power, the Ipeak371.1/Ipeak380.5 relative intensity Ipeak91.4/Ipeak380.5 rises evidently Additionally, the relative intensity Ipeak91.4/Ipeak380.5 is insensitive to the pressure, the duty cycle, and the load power.

DSC based Dual-Resunet for radio frequency interference identification

Radio frequency interference(RFI)will pollute the weak astronomical signals received by radio telescopes,which in return will seriously affect the time-domain astronomical observation and research.In this paper,we use a deep learning method to identify RFI in frequency spectrum data,and propose a neural network based on Unet that combines the principles of depthwise separable convolution and residual,named DSC Based Dual-Resunet.Compared with the existing Unet network,DSC Based Dual-Resunet performs better in terms of accuracy,F1 score,and MIoU,and is also better in terms of computation cost where the model size and parameter amount are 12.5%of Unet and the amount of computation is 38%of Unet.The experimental results show that the proposed network is a high-performance and lightweight network,and it is hopeful to be applied to RFI identification of radio telescopes on a large scale.

Improvement of surface hydrophobicity on silicone rubber modified by CF_4 radio frequency capacitively coupled plasma

In order to improve the surface hydrophobicity, silicone rubber （SIR） samples were exposed to CF4 radio frequency （RF） capacitively coupled plasma （CCP）. Attenuated total reflection Fourier transform infrared （ATR-FTIR） spectrum and X-ray photoelectron spectroscopy （XPS） were used to observe the variation of the functional groups of the modified SIR. Static contact angle （SCA） was employed to estimate the change of hydrophobicity of the modified SIR. The surface energy of SIR is reduced largely from 27.37 mJ/m^2 of original SIR sample to 2.94 mJ/m^2 of SIR sample treated by CF4 CCP modification at RF power of 200 W for a treatment time of 5 rnin. According to the XPS, ATR-FTIR and surface energy analysis, it is suggested that the improvement of hydrophobicity on the modified SIR surface is mainly ascribed to the decrease of surface energy, which is caused by the cooperation of the fluosilicic structure of Si--F or Si--F2 and the fluoric groups of C--CFn induced by the methyl replacement reaction and residual methyl groups of SIR surface.

Effects of back gate bias on radio-frequency performance in partially depleted silicon-on-inslator nMOSFETs

The effects of back gate bias(BGEs) on radio-frequency(RF) performances in PD SOI n MOSFETs are presented in this paper. Floating body(FB) device, T-gate body-contact(TB) device, and tunnel diode body-contact(TDBC) device, of which the supply voltages are all 1.2 V, are compared under different back gate biases by different figures of merit, such as cut-off frequency( fT), maximum frequency of oscillation( fmax), etc. Because of the lack of a back gate conducting channel, the drain conductance(gd) of TDBC transistor shows a smaller degradation than those of the others, and the trans-conductance(gm) of TDBC is almost independent of back gate bias. The values of fT of TDBC are also kept nearly constant under different back gate biases. However, RF performances of FB and TB each show a significant degradation when the back gate bias is larger than ～ 20 V. The results indicate that TDBC structures could effectively improve the back gate bias in RF performance.

Modeling of Biological Tissues Response to Radio Frequency （RF）： Towards Remote Sensing of Electrocardiography Signal

Premature newborns are at high risk of developing infections, so they require continuous monitoring of vital parameters for long periods of time, until they approximately reach the pregnancy due date. ECG （electrocardiography） is one of the most widely used method for evaluating the structure-function relationship of the heart in health and in sickness. Due to incomplete skin development, premature newborns have some special requirements to the ECG monitoring electrodes. Contact ECG monitoring adversely affects the health and comfort of the newborns. The goal of this study is to determine the feasibility of using RF （radio frequency） in ECG signal remote sensing. This requires studying the interaction mechanisms between RF fields and biological tissues The ECG current propagated from the heart through the skin has an effect on the permittivity of the skin which is frequency dependent. Thus, the feasibility of detecting the change of the relative permittivity in the presence of ECG signal is also discussed. The RF biological tissues response is simulated using MATLAB software in preparation for experimental validation.

Analysis of non-uniform hetero-gate-dielectric dual-material control gate TFET for suppressing ambipolar nature and improving radio-frequency performance

A tunnel field-effect transistor(TFET) is proposed by combining various advantages together, such as non-uniform gate-oxide layer, hetero-gate-dielectric(HGD), and dual-material control-gate(DMCG) technology. The effects of the length of non-uniform gate-oxide layer and dual-material control-gate on the on-state, off-state, and ambipolar currents are investigated. In addition, radio-frequency performance is studied in terms of gain bandwidth product, cut-off frequency,transit time, and transconductance frequency product. Moreover, the length of non-uniform gate-oxide layer and dualmaterial control-gate are optimized to improve the on-off current ratio and radio-frequency performances as well as the suppression of ambipolar current. All results demonstrate that the proposed device not only suppresses ambipolar current but also improves radio-frequency performance compared with the conventional DMCG TFET, which makes the proposed device a better application prospect in the advanced integrated circuits.