Adsorbent for Arsenic(V) Removal Synthesized by Radiation-Induced Graft Polymerization onto Nonwoven Cotton Fabric

A fibrous adsorbent for arsenic (As) removal was synthesized with nonwoven cotton fabric as a trunk polymer. 2-hydroxyethyl methacrylate phosphoric acid monomer which composed of phosphoric acid mono (50%) and di (50%) ethyl methacrylate ester was introduced with radiation-induced graft polymerization onto nonwoven cotton fabric. The degree of grafting of 130% was obtained at irradiation dose of 20 kGy with 5% of monomer solution for 2 hours reaction time at 40?C reaction temperature. After the grafted material was contacted with 10 mmol/L of zirconium (Zr) solution at pH 1, 0.38 mmol/g of Zr was loaded on phosphoric units as a functional group for As(V) removal. The resulting adsorbent was evaluated by column mode adsorption with 1 mg/L of As(V) solution at various pH with space velocity 200 h–1. The maximum capacity of As(V) adsorption was 0.1 mmol/g at pH 2.

Ultravilolet-radiation-induced graft polymerization of acrylamide onto the melt-blown polypropylene filter element by dynamic method

By dynamic method under UV irradiation, commercial melt-blown polypropylene （PPMB） filter element was modified with acrylamide （AAm） using benzophenone （BP） as initiator. Attenuated total reflection-Fourier transform infrared spectroscopy and scanning electron microscope verified that polyacrylamide chain was grafted on the fiber surface of PPMB filter element. Elemental content analysis with energy dispersive X-ray of fibers revealed that the polymerization content in the inner part of filter element was relatively higher than that in the outer. Degree of grafting changed with initiator concentration, monomer concentration, reaction temperature and reached 2.6% at the reaction condition： CBp=0.06 mol/L, CAAm=2.0 mol/L, irradiation time： 80 min, temperature： 60℃. Relative water flux altered with the hydrophilicity and pore size of filter element. In the antifouling test, the modified filter gave greater flux recovery （approximately 70%） after filtration of the water extract of Liuweidihuang, suggesting that the fouling layer was more easily reversible due to the hydrophilic nature of the modified filter.

Radiation-Induced Graft Polymerization of Sodium 4-Styrene Sulfonate onto Multiwalled Carbon Nanotubes and Their Application as Electrogenerated Chemiluminescence Biosensors

Sulfonate groups were introduced to the surfaces of multiwalled carbon nanotubes by the radiation-induced graft polymerization of sodium 4-styrene sulfonate for the use as biosensor supports. Alcohol dehydrogenase was immobilized onto a sulfonated nanotube-supporting electrode with tris（2,2＇-bipyridyl） ruthenium（II） complex to form an electrogenerated chemilluminesce sensor of alcohol. When it was used to detect alcohol in cyclic voltammetric measurements, the sensor showed the linearity over the range of 1.0 × 10^-4 M-5.0 ×10^-2 M, with a correlation coefficient of 0.992 and a detection limit of 1.9 ×10^-6 M. In electrogenerated chemilluminesce detection, it showed linearity over 5.0 × 10^-4 M-1.0 × 10^-2 M, with a correlation coefficient of 0.986 and a detection limit of 1.0 × 10^-6 M. The sensor was demonstrated to be able to detect ethanol in commercial drinks.

Rapid Biodiesel Fuel Production Using Novel Fibrous Catalyst Synthesized by Radiation-Induced Graft Polymerization

An efficient fibrous catalyst for the biodiesel fuel production has been synthesized by radiation-induced graft polymerization of 4-chloromethylstyrene onto a nonwoven polyethylene (NWPE) fabric followed by amination with trimethylamine (TMA) and further treatment with NaOH. The degree of grafting of NWPE fabric and TMA group density of fibrous catalyst could easily and reproducibly be controlled within a range of up to 340% and 3.6 mmol-TMA/g-catalyst, respectively. In the transesterification of triglycerides and ethanol using the synthesized fibrous catalyst, the conversion ratio of triglycerides reached 95% after 4 h reaction at 50°C.

Adsorption behavior of uranyl ions onto amino-type adsorbents prepared by radiation-induced graft copolymerization

Amino-type adsorbents(ATAs) were prepared by radiation-induced graft copolymerization of 4-hydroxybutyl acry late glycidyl ether(HB) onto a polyethylene-coated polypropylene(PE/PP) duplex fiber of a non-woven fabric,and modified with different amines of ethylenediamine(EDA),diethylenetriamine(DETA),triethylenetetramine(TETA) and diethylamine(DEA).The adsorption behavior of uranyl ions onto the ATAs was studied in batch experiments.The effects of the contact time,initial concentration of the ions,temperature,and pH value.The salinity were investigated along with the adsorption kinetics and the adsorption isotherms.The kinetic experimental data followed the pseudo second-order kinetic model,and the adsorption isotherms correlated well with the Langmuir model.The ATAs showed good efficiency in adsorbing uranyl ions,with the best saturation adsorption capacity being 64.26 mg g^(-1) for ATA-DETA within 120 min.The temperature dependence of ATADETA was quite abnormal and the quickest behavior was obtained at 25 ℃.ATAs showed good adsorption capacity over a wide pH range of 4.0-8.5,and HCl could be used in the elution process.Salinity of the solution had great effect on the adsorption capacity,3.5%salinity resulted in a 55%loss of capacity from ATA-DETA.The selectivity of ATA-DETA showed an order of:UO_2^(2+)≈Fe^(3+)> Zn^(2+) > VO_3^- > Co^(2+) > Ni^(2+).

Superhydrophobic melamine sponge prepared by radiation-induced grafting technology for efficient oil-water separation

This paper presents a superhydrophobic melamine(ME)sponge(ME-g-PLMA)prepared via high-energy radiation-induced in situ covalent grafting of long-alkyl-chain dodecyl methacrylate(LMA)onto an ME sponge for efficient oil–water separation.The obtained ME-g-PLMA sponge had an excellent pore structure with superhydrophobic(water contact angle of 154°)and superoleophilic properties.It can absorb various types of oils up to 66–168 times its mass.The ME-g-PLMA sponge can continuously separate oil slicks in water by connecting a pump or separating oil underwater with a gravity-driven device.In addition,it maintained its highly hydrophobic properties even after long-term immersion in different corrosive solutions and repeated oil adsorption.The modified ME-g-PLMA sponge exhibited excellent separation properties and potential for oil spill cleanup.

Lithium Salt Combining Fluoroethylene Carbonate Initiates Methyl Methacrylate Polymerization Enabling Dendrite-Free Solid-State Lithium Metal Battery

This work demonstrates a novel polymerization-derived polymer electrolyte consisting of methyl methacrylate,lithium bis(trifluoromethanesulfonyl)imide and fluoroethylene carbonate.The polymerization of MMA was initiated by the amino compounds following an anionic catalytic mechanism.LiTFSI plays both roles including the initiator and Li ion source in the polymer electrolyte.Normally,lithium bis(trifluoromethanesulfonyl)imide has difficulty in initiating the polymerization reaction of methyl methacrylate monomer,a very high concentration of lithium bis(trifluoromethanesulfonyl)imide is needed for initiating the polymerization.However,the fluoroethylene carbonate additive can work as a supporter to facilitate the degree of dissociation of lithium bis(trifluoromethanesulfonyl)imide and increase its initiator capacity due to the high dielectric constant.The as-prepared poly-methyl methacrylate-based polymer electrolyte has a high ionic conductivity(1.19×10^(−3)S cm^(−1)),a wide electrochemical stability window(5 V vs Li^(+)/Li),and a high Li ion transference number(t_(Li^(+)))of 0.74 at room temperature(RT).Moreover,this polymerization-derived polymer electrolyte can effectively work as an artificial protective layer on Li metal anode,which enabled the Li symmetric cell to achieve a long-term cycling performance at 0.2 mAh cm^(−2)for 2800 h.The LiFePO_(4)battery with polymerization-derived polymer electrolyte-modified Li metal anode shows a capacity retention of 91.17%after 800 cycles at 0.5 C.This work provides a facile and accessible approach to manufacturing poly-methyl methacrylate-based polymerization-derived polymer electrolyte and shows great potential as an interphase in Li metal batteries.

Magnetic resonance imaging findings of radiation-induced breast angiosarcoma:A case report

BACKGROUND Breast conservation surgery(BCS)with adjuvant radiotherapy has become a gold standard in the treatment of early-stage breast cancer,significantly reducing the risk of tumor recurrence.However,this treatment is associated with adverse effects,including the rare but aggressive radiation-induced angiosarcoma(RIAS).Despite its rarity and nonspecific initial presentation,RIAS presents a challenging diagnosis,emphasizing the importance of imaging techniques for early detection and accurate diagnosis.CASE SUMMARY We present a case of a 48-year-old post-menopausal woman who developed skin ecchymosis on the right breast seven years after receiving BCS and adjuvant radiotherapy for breast cancer.Initial mammography and ultrasound were inconclusive,showing post-treatment changes but failing to identify the underlying angiosarcoma.Contrast-enhanced breast magnetic resonance imaging(MRI)revealed diffuse skin thickening and nodularity with distinctive enhan-cement kinetics,leading to the diagnosis of RIAS.This case highlights the crucial role of MRI in diagnosing and determining the extent of RIAS,facilitating timely and appropriate surgical intervention.CONCLUSION Breast MRI is crucial for detecting RIAS,especially when mammography and ultrasound are inconclusive.

Efficient in-situ end-functionalization of polydienes by isothiocyanate via neodymium mediated coordinative chain transfer polymerization system

End-functionalization of polydiene rubbers can not only improve its compatibility with inorganic fillers,but also enhance the overall mechanical properties.Nevertheless,for traditional neodymium(Nd)diene polymerization systems,it is highly challenging to achieve such end-functionalizations,because most of polydienyl chains are capped withη3-allyl-Nd moiety during the end of polymerization,which shows very poor reactivity with nucleophile compounds.We launched a new diene polymerization strategy calling coordinative chain transfer polymerization(CCTP)[1].In such a system,all the polydienyl chains are capped withη1-allyl-Al moieties,which reveal greater reactivity with cyclic esters and epoxide compounds,providing an effective manner to prepare polydiene-polyester amphiphilic block copolymers.Inspired by such findings,we now show herein how such types of chain-ends react with isot-hiocyanate to demonstrate an efficient in-situ manner to access end-functionalized polydienes by using CCTP.

Influence of external nitrogen-containing donors on polymerization behavior of neodymium-based cis-1,4-polybutadiene rubber

Neodymium(Nd)-based catalyst in butadiene(Bd)polymerization has drawn interests due to its availability in affording higher cis-1,4-unit selectivity than transition metal(Ti,Co,Ni,etc.)-based catalysts[1-2].Such outstanding high cis-1,4-unit selecti-vity is hypothetically originated from the presence of 4 f orbitals,that can participate in monomer coordination and thereby govern subsequent enchainment manners.This unique characteristic also renders the active species highly susceptible to Lewis bases,and may impact the overall selectivity as well as polyme-rization behavior after coordination.Nevertheless,it is still a virgin area in such a field,and the influence of Lewis bases on Nd-based diene polymerizations is still a black box.Based on this consideration,how nitrogen-containing donors(D)impacts the overall behaviors of Nd-mediated Bd polymerizations is disclosed.

Nickel catalysts with asymmetric steric hindrance for ethylene polymerization

α-Diimide catalysts have attracted widespread attention due to their unique chain walking characteristics.A series ofα-diimide nickel/palladium catalysts with different electronic effects and steric hindrances were designed and synthesized for olefin polymerization.In this work,we synthesized a series of asymmetricα-diimide nickel complexes with different steric hindrances and used them for ethylene polymerization.These nickel catalysts have high ethylene polymerization activity,up to 6.51×10^(6)g·mol^(−1)·h^(−1),and the prepared polyethylene has a moderate melting point and high molecular weight(up to 38.2×10^(4)g·mol^(−1)),with a branching density distribution between 7 and 94 branches per 1000 carbons.More importantly,the polyethylene prepared by these catalysts exhibits excellent tensile properties,with strain and stress reaching 800%and 30 MPa,respectively.

3D printing encouraging desired in-situ polypyrrole seed-polymerization for ultra-high energy density supercapacitors

The tireless pursuit of supercapacitors with high energy density entails the parallel advancement of wellsuited electrode materials and elaborately engineered architectures.Polypyrrole(PPy)emerges as an exceedingly conductive polymer and a prospective pseudocapacitive materials for supercapacitors,yet the inferior cyclic stability and unpredictable polymerization patterns severely impede its real-world applicability.Here,for the first time,an innovative seed-induced in-situ polymerization assisted 3D printing strategy is proposed to fabricate PPy-reduced graphene oxide/poly(vinylidene difluoride-cohexafluoropropylene)(PVDF-HFP)(PPy-rGO/PH)electrodes with controllable polymerization behavior and exceptional areal mass loading.The preferred active sites uniformly pre-planted on the 3D-printed graphene substrates serve as reliable seeds to induce efficient polypyrrole deposition,achieving an impressive mass loading of 185.6 mg cm^(-2)(particularly 79.2 mg cm^(-2)for polypyrrole)and a superior areal capacitance of 25.2 F cm^(-2)at 2 mA cm^(-2)for a 12-layer electrode.In agreement with theses appealing features,an unprecedented areal energy density of 1.47 mW h cm^(-2)for a symmetrical device is registered,a rarely achieved value for other PPy/rGO-based supercapacitors.This work highlights a promising route to preparing high energy density energy storage modules for real-world applications.

Two-photon polymerization lithography for imaging optics

Optical imaging systems have greatly extended human visual capabilities,enabling the observation and understanding of diverse phenomena.Imaging technologies span a broad spectrum of wavelengths from x-ray to radio frequencies and impact research activities and our daily lives.Traditional glass lenses are fabricated through a series of complex processes,while polymers offer versatility and ease of production.However,modern applications often require complex lens assemblies,driving the need for miniaturization and advanced designs with micro-and nanoscale features to surpass the capabilities of traditional fabrication methods.Three-dimensional(3D)printing,or additive manufacturing,presents a solution to these challenges with benefits of rapid prototyping,customized geometries,and efficient production,particularly suited for miniaturized optical imaging devices.Various 3D printing methods have demonstrated advantages over traditional counterparts,yet challenges remain in achieving nanoscale resolutions.Two-photon polymerization lithography(TPL),a nanoscale 3D printing technique,enables the fabrication of intricate structures beyond the optical diffraction limit via the nonlinear process of two-photon absorption within liquid resin.It offers unprecedented abilities,e.g.alignment-free fabrication,micro-and nanoscale capabilities,and rapid prototyping of almost arbitrary complex 3D nanostructures.In this review,we emphasize the importance of the criteria for optical performance evaluation of imaging devices,discuss material properties relevant to TPL,fabrication techniques,and highlight the application of TPL in optical imaging.As the first panoramic review on this topic,it will equip researchers with foundational knowledge and recent advancements of TPL for imaging optics,promoting a deeper understanding of the field.By leveraging on its high-resolution capability,extensive material range,and true 3D processing,alongside advances in materials,fabrication,and design,we envisage disruptive solutions to current challenges and a promising incorporation of TPL in future optical imaging applications.

Effect of solvent on the initiation mechanism of living anionic polymerization of styrene:A computational study

For living anionic polymerization(LAP),solvent has a great influence on both reaction mechanism and kinetics.In this work,by using the classical butyl lithium-styrene polymerization as a model system,the effect of solvent on the mechanism and kinetics of LAP was revealed through a strategy combining density functional theory(DFT)calculations and kinetic modeling.In terms of mechanism,it is found that the stronger the solvent polarity,the more electrons transfer from initiator to solvent through detailed energy decomposition analysis of electrostatic interactions between initiator and solvent molecules.Furthermore,we also found that the stronger the solvent polarity,the higher the monomer initiation energy barrier and the smaller the initiation rate coefficient.Counterintuitively,initiation is more favorable at lower temperatures based on the calculated results ofΔG_(TS).Finally,the kinetic characteristics in different solvents were further examined by kinetic modeling.It is found that in benzene and n-pentane,the polymerization rate exhibits first-order kinetics.While,slow initiation and fast propagation were observed in tetrahydrofuran(THF)due to the slow free ion formation rate,leading to a deviation from first-order kinetics.

Synthesis of Branched Polyethylene via Bulky α-Diimine Nickel(II)-Catalyzed Ethylene Chain-Walking Polymerization

The catalysis of olefin polymerization through the chain-walking process is a subject of great interest. In this contribution, the successful synthesis of a Brookhart-type unsymmetrical α-diimine nickel catalyst Ni, which contains both dibenzhydryl and phenyl groups, was determined by X-ray crystallography. The compound has a pseudo-tetrahedral geometry at the Ni center, showing pseudo-C2-symmetry. Upon activation with modified methylaluminoxane (MMAO), Ni1 exhibits high catalytic activity up to 1.02 × 107 g PE (mol Ni h)−1 toward ethylene polymerization, enabling the synthesis of high molecular weight branched polyethylene. The molecular weights and branching densities could be tuned over a very wide range. The polymerization results indicated the possibility of precise microstructure control, depending on the polymerization temperature. The branching densities were decreased with increasing the polymerization temperature.

Synthesis and Characterization of Poly Styrene-Co-Poly 2-Hydroxyethylmethacrylate (HEMA) Copolymer and an Investigation of Free-Radical Copolymerization Propagation Kinetics by Solvent Effects

A series of homo and copolymers of styrene (ST) and 2-hydroxyethyl methacrylate (HEMA) in three different media (bulk, tetrahydrofuran, and benzene) have been investigated by free radical polymerization method. The samples obtained from the synthesis were characterized by Fourier Transform-Infrared spectroscopy (FT-IR), proton nuclear magnetic resonance spectroscopy (1H NMR), atomic force microscopy (AFM), and differential scanning calorimetry (DSC). The results show that the synthesis of the polymers is more feasible under neat conditions rather than solvent directed reaction. Moreover, the DSC data shows that the polystyrene obtained is amorphous in nature and therefore displayed only a glass transition signal rather than crystallization and melting peaks. In addition, this study indicates that homolopolymerization of styrene via free radical polymerization tends to be preferable in less polar solvents like THF than in non-polar solvents like benzene. Benzene might destabilize the formation of the reactive radicals leading to the formation of the products. In summary, the homolpolymerization of styrene is more feasible than the homopolymerization 2-hydroxyethyl methacrylate under the experimental setup used. Styrene is more reactive than 2-hydroxyethyl methacrylate than free radical polymerization reaction due in part of the generation of the benzylic radical intermediate which is more stable leading to the formation of products than alkyl radical which are less stable. Furthermore, polymerization of styrene under neat conditions is preferable in solvent-assisted environments. The choice of solvent for the synthesis of these polymers is crucial and therefore the selection of solvent that leads to the formation of a more stable reaction intermediate is more favorable. It is worth noting that the structure of the proposed copolymer consists of a highly polar and hydrophilic monomer, 2-hydroxyethyl methacrylate and a highly non-polar and hydrophobic monomer, styrene. These functionalities constitute an amphiphilic copolymer with diverse characteristics. A plausible explanation underlying our observations is that the reaction conditions employed in the synthesis of these copolymers might not be the right route required under free radical polymerization.

Study on kinetics of propylene polymerizationat different temperatures via Monte Carlo simulation

The elementary reactions of propylene polymerization catalyzed by conventional Ziegler-Natta catalysts was proposed according to the comprehensive view and without considering the effect of any impurity in the material on propylene polymerization. The Monte Carlo simulation technique was employed to investigate the kinetics of propylene polymerization in order to determine the validity of the stationary state assumption and the effects of the polymerization temperature on the polymerization. The simulated total amount of active species, which only increases quickly at the beginning of the polymerization, indicates that the stationary state assumption in the studied system is valid. Moreover, significant effects of polymerization temperature on the polymerization conversion, and the molecular weight and its distribution were also analyzed. The simulated results show that the consumption rate of propylene increases with the increase of polymerization temperature; the maximum values of the number-average degree of polymerization are constant at different polymerization temperatures, however, the peak appears earlier with the higher temperature; as the polymerization temperature increases, the average molecular weight decreases and the molecular weight distribution changes greatly.

Enhanced thermal and electrical properties of poly (D,L-lactide)/ multi-walled carbon nanotubes composites by in-situ polymerization

Biodegradable poly （D,L-lactide） （PLA）/carboxyl-functionalized multi-walled carbon nanotubes （c-MWCNTs） composites were achieved via in-situ polymerization. These as-prepared composite materials were characterized with FT-IR, XRD, TG, DSC, SEM, and high insulation resistance meter. The results demonstrate that the multi-walled carbon nanotube was carboxyl functionalized, which improved the collection between c-MWCNTs and PLA, and further realized the graft copolymerization of c-MWCNTs and PLA. There is a higher glass transition temperature and a lower pyrolysis temperature of PLA/c-MWCNTs composites than pure PLA. The c-MWCNTs gave a better dispersion than unmodified MWCNTs in the PLA matrix, and an even coating of PLA on the surface of c-MWCNTs was obtained, which increased the interfacial interaction. High insulation resistance analysis showed that the addition of c-MWCNTs increased the electric conductivity, and c-MWCNTs performed against the large dielectric coefficient and electrostatic state of PLA. These results demonstrated that c-MWCNTs modified PLA composites were beneficial for potential application in the development of heat-resisting and conductivity plastic engineering.

An Investigation on the Polymerization of Styrene by Fluorescence Probe Technique

The polymerization of styrene is monitored by pyrene excimer formation. The ratio of monomer to excimer intensities ( I m/ I e) of pyrene increases as polymerization proceeds. The increase of I m/ I e is ascribed to the increase of microviscosity surrounding the probes forming excimer during polymerization. The linear relationship between the changing rate of I m/ I e and the polymerization rate of styrene is obtained. Therefore, I m/ I e may be used to monitor the progress of the polymerization of styrene.

Polymerization Mechanism of α-Linear Olefin

The density functional theory on the level of B3LYP/6-31G was empolyed to study the chain growth mechanism in polymerization process of α-linear olefin in TiCl3/AlEt2Cl catalytic system to synthesize drag reduction agent. Full parameter optimization without symmetry restrictions for reactants, products, the possible transition states, and intermediates was calculated. Vibration frequency was analyzed for all of stagnation points on the potential energy surface at the same theoretical level. The internal reaction coordinate was calculated from the transition states to reactants and products respectively. The results showed as flloes： （i） Coordination compounds were formed on the optimum configuration of TiCl3/AlEt2Cl.（ii） The transition states were formed. The energy di？erence between transition states and the coordination compounds was 40.687 kJ/mol. （iii） Double bond opened and Ti-C（4） bond fractured, and the polymerization was completed. The calculation results also showed that the chain growth mechanism did not essentially change with the increase of carbon atom number of α-linear olefin. From the relationship between polymerization activation energy and carbon atom number of the α-linear olefin, it can be seen that the α-linear olefin monomers with 6-10 carbon atoms had low activation energy and wide range. It was optimum to synthesize drag reduction agent by polymerization.