Drag reduction characteristics of recirculation flow at rocket base in an RBCC engine under ramjet/scramjet mode

To reduce the drag generated by the recirculation flow at the rocket base in a RocketBased Combined Cycle(RBCC)engine operating in the ramjet/scramjet mode,a novel annular rocket RBCC engine based on a central plug cone was proposed.The performance loss mechanism caused by the recirculation flow at the rocket base and the influence of the plug cone configuration on the thrust performance were studied.Results indicated that the recirculation flow at the rocket base extended through the entire combustor,which creates an extensive range of the"low-kineticenergy zone"at the center and leads to an engine thrust loss.The plug cone serving as a surface structure had a restrictive effect on the internal flow of the engine,making it smoothly transit at the position of the large separation zone.The model RBCC engine could achieve a maximum thrust augmentation of 37.6%with a long plug cone that was twice diameter of the inner isolator.However,a shorter plug cone that was half diameter of the inner isolator proved less effective at reducing the recirculation flow for a supersonic flow and induced an undesirable flow fraction that diminished the thrust performance.Furthermore,the effectiveness of the plug cone increased with the flight Mach number,indicating that it could further broaden the operating speed range of the scramjet mode.

三种湍流对Scramjet燃烧室冷态流场的数值模拟

为验证从超音速混合层中发展而来的修正可压缩性(包括膨胀可压缩性和结构可压缩性两部分)的k-ε湍流模型对复杂超音速流场的预测能力,对复杂的超音速燃烧冲压发动机(Scramjet)燃烧室冷态流场进行数值模拟.将修正k-ε模型、标准k-ε模型以及标准k-ωSST模型的计算结果与实验结果进行了对比.结果表明,修正k-ε模型能够较好地预测该复杂流场,对湍流动能的预测改进较大,优于k-ωSST的结果,与实验吻合得较好;壁面压力分布以及速度分布在激波附近修正明显,与实验结果更加吻合.

Scramjet燃烧室流场的三维并行数值模拟及试验比较

作者采用时间相关法,通过有限体积离散,运用带化学反应的全N S方程,在神州巨型机上,针对试验模型,对油气比Φ=0.0和0.35的喷氢Scramjet燃烧室流场进行了三维并行数值模拟,得到了流场的精细结构。并行模拟所得壁面压力分布与试验所测得的壁面压力分布吻合较好。

Scramjet尾喷管几何调节方案的计算与实验研究

高超声速飞行器飞行接力点和巡航结束点尾喷管冷、热态俯仰力矩差较大,给飞行器的飞行姿态控制造成严重影响。为了减小喷管冷、热态俯仰力矩差,提出了在喷管上膨胀面末端增加移动板进行调节的方案,并进行了详细的三维数值模拟和相应的风洞缩比冷流实验研究。计算结果表明,Ma=4.5时,调节移动板伸出400mm,喷管冷、热态力矩差最大减小21.74%,推力系数损失1.64%;Ma=6.5时,调节移动板喷管冷、热态力矩差可降低77.59%,而推力系数只减小1.35%,调节收益非常明显。最后通过将喷管各调节状态下的冷流缩比实验壁面压力数据与计算结果的对比,证明了该调节方案的计算方法及其结果是可靠的,同时得出该调节方案可以有效地降低冷、热态力矩差的结论。

MHD-Arc-Scramjet联合循环发动机的性能分析

以MHD-Arc-Scramjet联合循环发动机为对象开展性能分析，探讨了能量旁路系统对发动机性能的影响，给出了MHD-Arc-Scramjet联合循环发动机相对于传统冲压发动机的单位推力差异。结果表明：电子束电离消耗的能量，能量旁路比例，电弧注入过程的最高温度以及进气道的压缩程度是能量旁路系统中影响发动机单位推力的主要因素；在这些参数的取值范围内合理取值，并兼顾材料和技术实现等约束，性能分析表明：在来流速度2800-4000m／s范围内MHD-Arc-Scramjet联合循环发动机相对传统冲压发动机具有明显的单位推力优势。

模拟Scramjet隔离段实际入口的直连试验设备设计试验验证

为了模拟进气道喉道非均匀流场对超燃冲压发动机隔离段流动特性的影响,针对典型超燃冲压发动机隔离段入口流场的马赫数分布要求,设计了隔离段直连试验设备。该设备整个通道采用扩张构型,在附面层发展段的下壁面采用加圆形凸台的方法加速附面层发展,并针对该设备进行了数值模拟和冷流试验。结果表明,该直连试验设备不仅能准确模拟隔离段实际入口流场(即入射激波和非对称附面层),模拟的主流区马赫数与目标值差值在0.02以内,还解决了传统的直连试验设备存在的启动问题。试验与数值模拟结果吻合较好,验证了该直连试验设备设计方法的可行性。

Scramjet整机流场的非结构网格并行数值模拟

为了得到某支板喷氢超燃冲压发动机内流场的细节,采用非结构网格CFD隐式解算器,耦合求解Na-vire-Stokes方程、组分连续方程和M enter的k-ω应力剪切传输(SST)湍流模型,对整机模型的冷流和三个当量油气比的湍流反应流进行了三维并行模拟。给出了流线和水的分布云图,分析了支板附近旋涡和推进流道一维质量加权平均的马赫数、静温、组分质量分数及燃烧效率等参数随当量油气比的变化,并将壁面压力和实验值进行了比较,吻合较好。除=0.8在支板附近出现了小范围亚声速外,其余状态整个内流道超声速占主流。

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scrarnjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combustor performances. In addition, an irmer-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.

Experimental investigation of combustion mechanisms of kerosene-fueled scramjet engines with double-cavity flameholders

A scramjet combustor with double cavitybased flameholders was experimentally studied in a directconnected test bed with the inflow conditions of M = 2.64,Pt = 1.84 MPa,Tt = 1 300 K.Successful ignition and selfsustained combustion with room temperature kerosene was achieved using pilot hydrogen,and kerosene was vertically injected into the combustor through 4×φ 0.5 mm holes mounted on the wall.For different equivalence ratios and different injection schemes with both tandem cavities and parallel cavities,flow fields were obtained and compared using a high speed camera and a Schlieren system.Results revealed that the combustor inside the flow field was greatly influenced by the cavity installation scheme,cavities in tandem easily to form a single side flame distribution,and cavities in parallel are more likely to form a joint flame,forming a choked combustion mode.The supersonic combustion flame was a kind of diffusion flame and there were two kinds of combustion modes.In the unchoked combustion mode,both subsonic and supersonic combustion regions existed.While in the choked mode,the combustion region was fully subsonic with strong shock propagating upstream.Results also showed that there was a balance point between the boundary separation and shock enhanced combustion,depending on the intensity of heat release.

Fabrication and Thermal Structural Characteristics of Ultra-high Temperature Ceramic Struts in Scramjets

ZrB_2-SiC based ultra-high temperature ceramic（UHTC） struts were firstly proposed and fabricated with the potential application in the combustor of scramjets for fuel injection and flame-holding for their machinability and excellent oxidation/ablation resistance in the extreme harsh environment. The struts were machined with electrospark wire-electrode cutting techniques to form UHTC into the desired shape, and with laser drilling to drill tiny holes providing the channels for fuel injection. The integrated thermal-structural characteristic of the struts was evaluated in high-temperature combustion environment by the propane-oxygen free jet facility, subject to the heat flux of 1.5 MW/m^2 lasting for 300 seconds, and the struts maintained integrity during and after the first experiment. The experiments were repeated for verifying the reusability of the struts. Fracture occurred during the second repeated experiment with the crack propagating through the hole. Finite element analysis（FEA） was carried out to study the thermal stress distribution in the UHTC strut. The simulation results show a high thermal stress concentration occurs at the hole which is the crack initiation position. The phenomenon is in good agreement with the experimental results. The study shows that the thermal stress concentration is a practical key issue in the applications of the reusable UHTC strut for fuel injection structure in scramjets.

Simulation of turbulent combustion in DLR Scramjet

Turbulent combustion in a DLR (German Aerospace Center) Scramjet engine was simulated using the newly-proposed Partially Resolved Numerical Simulation (PRNS) procedure. The PRNS procedure uses temporal filtering to define large-scale turbulence, and the model developed to account for unresolved scales is grid independent. No problem about inner commutation error and inconsistencies will arise from the PRNS, while such issues are of concern in traditional Large Eddy Simulation (LES) methods. The mean results have good agreement with the experiment data and the flow structures with small scales are well resolved.

Engine performance analysis and optimization of a dual-mode scramjet with varied inlet conditions

A dual-mode scramjet can operate in a wide range of flight conditions. Higher thrust can be generated by adopting suitable combustion modes. Based on the net thrust, an analysis and preliminary optimal design of a kerosene-fueled parameterized dual-mode scramjet at a cru- cial flight Mach number of 6 were investigated by using a modified quasi-one-dimensional method and simulated annealing strategy. Engine structure and heat release distrib- utions, affecting the engine thrust, were chosen as analytical parameters for varied inlet conditions （isolator entrance Mach number： 1.5-3.5）. Results show that different opti- mal heat release distributions and structural conditions can be obtained at five different inlet conditions. The highest net thrust of the parameterized dual-mode engine can be achieved by a subsonic combustion mode at an isolator entrance Mach number of 2.5. Additionally, the effects of heat release and scramjet structure on net thrust have been discussed. The present results and the developed analytical method can provide guidance for the design and optimization of high-performance dual-mode scramjets.

Flame quenching process in cavity based on model scramjet combustor

The flame quenching process in combustors was observed by high speed camera and Schlieren system, at the inflow conditions of Ma = 2.64, To = 1483K, P0 = 1.65 MPa, T = 724 K and P -- 76.3 kPa. Changing process of the flame and shock structure in the combustor was clearly observed. The results revealed that the precom- bustion shock disappeared accompanied with the process in which the flame was blown out and withdrawed from the mainflow into the cavity and vanished after a short while. The time of quenching process was extended by the cavity flame holder, and the ability of flame holding was enhanced by arranging more cavities in the downstream as well. The flame was blown from the upstream to the downstream, so the flame in the downstream of the cavity was quenched out later than that in the upstream.

Effects of Wall Emissivity on Aerodynamic Heating in Scramjets

The effects of the wall emissivity on aerodynamic heating in a scramjet are analyzed.The supersonic turbulent combustion flow including radiation is solved in the framework of a decoupled strategy where the flow field is determined first and the radiation field next.In particular,a finite difference method is used for solving the flow while a DOM(iscrete ordinates method)approach combined with a WSGGM(weighted sum of gray gases)model is implemented for radiative transfer.Supersonic nonreactive turbulent channel flows are examined for a DLR hydrogen fueled scramjet changing parametrically the wall emissivity.The results indicate that the wall radiative heating rises greatly with increasing the wall emissivity.As the wall emissivity rises,the radiative source and total absorption increase,while the incident radiation decreases apparently.Notably,although the radiative heating can reach a significant level,its contribution to the total aerodynamic heating is relatively limited.

Study on Feasibility of Reusable Rocket Launching Technology by Use of Scramjet and Maglev Technologies

The scramjet and maglev engineering technology development and trends at home and abroad are firstly presented in this paper. A new launch mode of space transportation system is proposed based on scramjet and magnetic suspension technologies, and its key technologies required are given. This paper also makes analysis on using scramjet and magnetic suspension technologies to launch a reusable rocket, and the results show that a normal temperature conductor maglev launch system is feasible.

Experimental Study of Ethylene Combustion in a Scramjet Combustor

In this paper the ignition characteristics of gaseous ethylene hydrocarbon fuel is investigated in the supersonic clean airstreams experimental facility with a resistance heater. The generic cavity flame holder is used to create recirculation and promote the fuel/air mixing at the lower wall of the combustor. Three different injection concepts are considered in this research ： （ 1 ） ethylene injection upstream of the cavity ; （2） ethylene and hydrogen injection upstream of the cavity simultaneously; （ 3 ）ethylene injection preceded by pilot hydrogen injection. The pilot injection showed to be a supportive tool for holding the flame of the main normal ethylene fuel injection. Therefore, using pilot hydrogen injection and cavity configuration necessitates optimizing the combustor length to ensure the complete combustion and the full liberation of the chemical energy stored in the fuel before exiting the combustor.The present study proved the possibility of igniting the ethylene and maintaining its flame in the supersonic airstreams.

马赫数10条件下冲压发动机内氢气燃烧特性试验

针对高马赫数超燃冲压发动机面临的高效燃烧组织挑战,本文提出了一种凹腔后缘激波强化的高马赫数超声速燃烧组织技术,并设计了一套燃烧室采用双侧对称布置凹腔结构的三维发动机试验模型。采用OH*基化学发光光谱诊断与壁面测压相结合的试验手段,在自由活塞驱动激波风洞的名义Ma=10流场中,对凹腔上游横向氢气射流的燃烧特性进行了研究,并讨论了模拟流场的重复性,给出了氢气燃烧演化特征、火焰稳定结构及释热特性。不同车次的总压等流场参数表明试验流场具有较高的重复性,可保障氢气燃烧特性的可复现性。通过观察试验过程中OH*基动态发光特征发现,在高焓激波风洞发动机试验中采用燃料提前喷注的方法使发动机流道在空气主流到来之前充盈大量的氢气,进而在主流到达发动机内的瞬间形成所谓“激波管流动-燃烧”效应,使来流空气与氢气接触面发生自点火与剧烈燃烧,产生显著不同于发动机正常工作情况下的点火与燃烧机制,但随着主流趋于平稳,“激波管流动-燃烧”效应消失,在高总温气流的自点火效应与凹腔后缘的X型激波耦合作用下,火焰稳定在凹腔上游近壁面区的氢气射流尾迹区和凹腔后缘附近的全流场中。通过分析壁面压力分布特征发现,凹腔后缘的X型激波实现了燃烧的强化与火焰的稳定,并获得了最显著的释热压升。这些结果表明高马赫数冲压发动机可利用凹腔后缘X型激波强化燃烧和稳定火焰。

一种组合动力飞行器模态转换过程轨迹优化与控制方案

为应对组合动力飞行器涡轮/冲压发动机模态转换过程中容易出现的推力陷阱问题,开展了组合动力飞行器模态转换阶段飞行/推进一体化保护控制研究。该研究利用组合动力爬升段飞行轨迹优化方法,解决模态转换过程中组合发动机总推力无法满足平飞加速需求的推力陷阱问题。结合轨迹线性化控制方法,完成了宽速域飞行器/发动机一体化轨迹跟踪控制设计,利用迎角、油门等变量的协同调节实现轨迹跟踪控制。仿真结果表明,轨迹优化策略能够在一定程度上克服模态转换过程中的推力不足问题,一体化轨迹线性化控制方法可以有效实现爬升轨迹跟踪,避免模态转换过程对组合动力飞行器飞行任务造成的不利影响。

MHD-Arc-Ramjet联合循环与AJAX间的性能比较

为了提高冲压发动机在更高速度区内的性能,扩展发动机的运行速度范围,需要在并行于发动机的燃烧室处附加一套能量旁路系统。采用热力学方法针对两种带有能量旁路的冲压发动机分别在理想和实际情况下进行了性能分析和比较,结果表明:理想条件下AJAX的单位推力要高于MHD-Arc-Ramjet联合循环;考虑到后者可以在更高的温度下进行能量注入,其在单位推力方面是具有优势的。实际条件下在很宽的飞行Ma范围内MHD-Arc-Ramjet联合循环的单位推力要高于AJAX。

超燃冲压发动机燃烧室流场超分辨率重建

超声速燃烧室受限空间内复杂流场波系结构的获取受到光学测量装置精度的制约。为提升流场时空分辨率特征,本文应用中国空气动力研究与发展中心地面脉冲燃烧风洞获取的试验数据,在发动机入口马赫数2.5的条件下,构建了6种不同当量比下基于压力数据重构的燃烧室流场低分辨率图像数据集,研究了三种提高图像分辨率的方法来提升超燃冲压发动机燃烧室流场重构图像的分辨率。结果表明,本文所提出的流场超分辨率稠密网络(Flow-field Super-Resolution Dense Network,FSRDN)、流场超分辨率生成对抗网络(Flow-field Super-Resolution Generative Adversarial Network,FSRGAN)、传统的双三次插值法(Bicubic interpolation,Bicubic)对流场图像分辨率都提高了4^(2)倍。FSRDN网络所得流场图像结果的峰值信噪比(Peak Signal-to-Noise Ratio,PSNR)、相关性系数(Correlation coefficient,CORR)、感知指数(Perceptual Index,PI)指标均优于双三次插值法,但实际图像存在过于平滑的现象。FSRGAN网络所得流场结果消除了图像平滑现象,使流场图像的细节更加丰富,大幅度优化了PI指标,对燃烧室内的剪切层、斜激波、分离激波等主要波系结构的清晰度有了极大的增强作用。