Effect of Mn addition on microstructure and mechanical properties of GX40CrNiSi25-12 austenitic heat resistant steel

Three types of steels were designed on the basis of GX40CrNiSi25-12 austenitic heat resistant steel by adding different Mn contents(2wt.%,6wt.%,and 12wt.%).Thermodynamic calculation,microstructure characterization and mechanical property tests were conducted to investigate the effect of Mn addition on the microstructure and mechanical properties of the austenitic heat resistant steel.Results show that the matrix structure in all the three types of steels at room temperature is completely austenite.Carbides NbC and M_(23)C_(6)precipitate at grain boundaries of austenite matrix.With the increase of Mn content,the number of carbides increases and their distribution becomes more uniform.With the Mn content increases from 1.99%to 12.06%,the ultimate tensile strength,yield strength and elongation increase by 14.6%,8.0%and 46.3%,respectively.The improvement of the mechanical properties of austenitic steels can be explained by utilizing classic theories of alloy strengthening,including solid solution strengthening,precipitation strengthening,and grain refinement.The increase in alloy strength can be attributed to solid solution strengthening and precipitation strengthening caused by the addition of Mn.The improvement of the plasticity of austenitic steels can be explained from two aspects:grain refinement and homogenization of precipitated phases.

Effect of CeO_2 on heat transfer and crystallization behavior of rare earth alloy steel mold fluxes

To improve the heat transfer capability and the crystallization property of the traditional mold flux, CaF_2 was replaced with B_2O_3. Then, the influences of CeO_2 on the heat transfer and the crystallization of the CaF_2-bearing mold flux and the new mold flux with 10 wt% B_2O_3 were studied using a slag film heat flux simulator and X-ray diffraction(XRD). The results revealed that the addition of CeO2 reduced the heat transfer by increasing the solid slag thickness and the crystallization of two mold fluxes. However, CeO_2 had less effect on the B_2O_3-containing mold flux compared with the CaF_2-bearing mold flux. According to the analyses, the CeO_2 contents in the CaF_2-bearing mold flux and the B_2O_3-containing mold flux should not exceed 8 wt% and 12 wt%, respectively. Therefore, these experimental results are beneficial to improve and develop the mold flux for casting rare earth alloy steels.

Effect of Rare Earth Elements on Quenching Crack Resistance of Steel 9Cr2Mo

The effect of rare earth elements on quenching crack resistance of steel 9Cr2Mo was investigated by means of scanning electron microscopy (SEM) and optical microscopy. Experimental results show that, by adding RE elements to steel 9Cr2Mo, the number of quenching for crack initiation is increased. Meanwhile the propagation of quenching cracks is postponed and the paths of crack propagation are changed. Therefore, quenching crack resistance can be improved by adding RE elements to steel 9Cr2Mo.

Effect of Rare Earth on Thermal Shock Resistance of Steel 9Cr2Mo

The effect of rare earth elements on thermal shock resistance of cold roller steel 9Cr2Mo was investigated by means of X-ray diffractometry and optical microscopy. Experimental results show that the process of carbide precipitation of heat effect zone is restrained by adding RE elements in steel 9Cr2Mo. Therefore, thermal shock resistance of this steel can be improved.

Effects of Rare Earths on Toughness of 31Mn2SiRE Wear- Resistance Cast Steel

The toughness of 31Mn2SiRE wear-resistance cast steel were increased by means of RE compound modification and high temperature austenitizing. The results show that the microstructures can be refined, needle and network ferrite are eliminated, the dislocation density and the quantity of dislocated martensite are increased remarkably, and the shape and distribution of inclusions are improved by the addition of RE. Therefore, the mechanical properties of the modified steel can be greatly increased, especially the toughness (αK) by 44%, yield strength (σs) by 10%, and elongation (δ5) by 42%.

APPLICATION OF RARE EARTH IN SURFACE HEAT TREATMENT OF HOT-WORKING DIE STEELS

This paper studies a compound treatment. i. e. liquid S , N,C co-diffusing with rare earth (RE) and then oxidization , for hot-working die steels , and the effect of RE on thermal fatigue behavior of the diffused layer. XRD and SEM energy spectrum prove that trace RE element actually penetrates into the surface layer of steels. The result shows that RE can reduce the gradient of change of hardness in diffused layer, improve the morphology and distribution of compounds , and reduce the degree of surface alligator crack for thermal fatigue. The behavior of thermal fatigue of hot-working die steels is raised by 70% or so after the application of RE. The effect of RE is analysed according to the theory.

Modifying Effect of Rare Earths and Titanium on Austenitic Manganese Steel

By means of thermodynamic calculations, optical microscope, sweep electron microscope(SEM), transimssion electron microscope(TEM) and microcomposition detection, the modifying effect of RE and Ti on austenitic manganese steel was investigated The results show that the constitutional supercooling of austenitic manganese steel during solidification can be improved and the dendritic crystals can be grown facilely, melted, isolated and multiplied by adding RE(Ce) In the melt the alloying elements Ti and C can form TiC directly which acts as nucleus of cementite and causes both primary and eutectic cementite to be granulated and refined so that the cementite network in this steel can be eliminated

Development and Application of a Heat-resistant Low Ni Steel Modified by Rare Earth for Furnace Roller

The low Ni steel modified hy rare earth(3Cr24NiTSiN with an addition of 0.3% Ce)for furnace roller has been developed.Due to the RE(rare earth)addition,a dense oxide film is formed on the steel surface at high temperature,and the oxidation rate is decreased.This film has so good adhesion to the matrix that it will not be peeled off easily.The RE modified steel has excellent oxidation resistance and thermal strength even if being used continuously for a long period at high temperature.This steel roller has a service life of about 4 years com- parable to high Ni steel ones,so the low Ni steel can replace high Ni steel to make furnace roller.The Ni content of this material can be reduced by 65% in comparison with Cr25Ni20Si2 steel,The low Ni steel has better pro- eessing properties including melting,casting and working properties than that of high Ni ones.

Low-Energy Multi-Impact Fracture Resistance of Cross Rolled Low Chromium Cast Semi-Steel Containing Rare Earth Grinding Ball

The low-energy multi-impact fracture resistance of the cross rolled low chromium cast semi-steel containing RE grinding balls was studied. Moreover, its damage mode was analyzed by means of metallographic examination, scanning electron microscopic examination and drop ball test. The results show that it can obtain extractive impact fracture resistance after proper heat treatment. More advantages were obtained for the ball worked in the condition of low-imp ductility act. The main reasons are the function of RE and the change in morphology of eutectic carbide network.

Effect of Rare Earth Elements on Austenite Growth Dynamics of Steel 9Cr2Mo

The growth dynamics of austenite grain was investigated in steel 9Cr2 Mo with different rare earth(RE)element addition.The results show that austenite grains of steel 9Cr2 Mo can be refined and their growth can be restrained by adding a certain amount of RE.According to the results,the n and Q were calculated and the mechanism of the refinement of austenite grains was discussed.

Coarsening behavior of MX carbonitrides in type 347H heat-resistant austenitic steel during thermal aging

In this work, the growth kinetics of MX （M - metal, X - C/N） nanoprecipitates in type 347H austenitic steel was systematically studied. To investigate the coarsening behavior and the growth mechanism of MX carbonitrides during long-term aging, experiments were performed at 700, 800, 850, and 900℃ for different periods （1, 24, 70, and 100 h）. The precipitation behavior of carbonitrides in specimens subjected to various aging conditions was explored using carbon replicas and transmission electron microscopy （TEM） observations. The corresponding sizes ofMX carbonitrides were measured. The results demonstrates that MX carbonitrides precipitate in type 347H austenitic steel as Nb（C,N）. The coarsening rate constant is time-independent; however, an increase in aging temperature results in an increase in coarsening rate of Nb（C,N）. The coarsening process was analyzed according to the calculated diffusion activation energy of Nb（C,N）. When the aging temperature was 800-900℃, the mean activation energy was 294 kJ·mol -1, and the coarsening behavior was controlled primarily by the diffusion of Nb atoms.

Effect of Rare Earth on Void Band of Diffusion Layer and Properties of Aluminized Steel

The effects of the addition of rare earth （RE） elements on the void band in the diffusion layer, and the re sistances to both oxidation and spalling of aluminized steel were investigated through high temperature oxidation and spalling tests. The results showed that RE had significant effects on the void band in the diffusion layer and the properties of aluminized steel. After diffusion treatment, a considerable number of the voids between the middle layer and transitional layer of pure aluminized coating, aggregated into wavy-line-shaped void bands parallel to the outer surface. For the RE added aluminized coating, only a few voids aggregated into intermittent block shapes. During high temperature oxidation at 800 ℃ for 200 h, the wavy void band of pure aluminized coating aggregated further into a linear crack parallel to the outer surface, and the internal oxidation occurred within them; the open cracks perpendicular to the surface penetrated through the diffusion layer. For the RE added aluminized coating, only a few voids aggregated into intermittent meniscus shapes. During cyclic spalling tests, the peeling, spallation, and pulver ulent cracking occurred along the void band in the diffusion layer of pure aluminized coating, but only a little spallation occurred in the diffusion layer of the RE-added aluminized coating, in which cracks perpendicular to the surface were much smaller than those of pure aluminized coating and did not penetrate through the diffusion layer. It is evident that RE addition can restrain the formation and aggregation of voids and subsequently improve the resistances to oxidation and spalling. The mechanism of the RE effect on the void band in the diffusion layer is also discussed.

Effect of Rare Earth Elements on Growth Dynamics of Austenite in 60CrMnMo Steel

The growth dynamics of austenite grains was investigated in 60CrMnMo steel with different RE elements. The results show that austenite grains of 60CrMnMo steel can be refined and their growth can be restrained by adding a certain amount of RE. From the experimental results, the values of n and Q were evaluated.

Hot deformation behavior of Super304H austenitic heat resistant steel

The hot compression tests of Super304H austenitic heat resistant steel were carried out at 800-1200℃and 0.005-5 s^-1 using a Gleeble 3500 thermal-mechanical simulator,and its deformation behavior was analyzed.The results show that the flow stress of Super304H steel decreases with the decrease of strain rate and the increase of deformation temperature; the hot deformation activation energy of the steel is 485 kJ/mol.The hot deformation equation and the relationship between the peak stress and the deformation temperature and strain rate is obtained.The softening caused by deformation heating cannot be neglected when both the deformation temperature and strain rate are higher.

Effect of Rare Earths on Corrosion Resisting Properties of Carbon-Manganese Clean Steels

Electrochemistry experiments were made on carbon-manganese clean steel with rare earths Ce and La respectively to observe corrosion parameters such as corrosion current i_(corr), and characteristic potential of pitting E_b. The results indicate that the rare earths have effect on corrosion resisting properties of carbon-manganese clean steel, and the optimum contents of La is about 0.011% (mass fraction) and Ce about 0.014% (mass fraction) respectively. The change of corrosion resistance is related to the action of rare earths on microstructure and effect on surface state of samples in the process of polarization.

High-Temperature Oxidation Behavior of 5Cr21Mn9Ni4N Steel Micro-Alloyed by Rare Earth

The oxidation resistance of 5Cr21Mn9Ni4N steel micro-alloying by RE at 700 - 900 ℃ was investigated. The results indicate that oxidation exponent n and oxidation activation energy are increased, and oxidation velocity constant kp is decreased when 0.2% RE is added in 5Cr21Mn9Ni4N steel. The addition of RE elements does not alter phase constitution of oxidation scale, however it improves the configuration of oxidation scale, and increases thermal stability and adhesivity of oxidation scale, which results in the raise of oxidation resistance of 5Cr21Mn9Ni4N steel at high temperature. The oxidation scale constitutes of refractory steel transfer from manganic oxide mostly to ferric oxide mostly with the increase of temperature, which leads to descend of compactness and desquamation resistance of oxidation scale. The mass increase of ferric oxide in the oxidation scale and the looseness of oxidation scale are the main reason to descend the oxidation resistance of refractory steel.

Influence of Heating Temperature on Property of Low Chromium Wear Resistant Cast Iron Containing Rare Earth

The influence of heating temperature on mechanical properties of low chromium wear resistant cast iron containing rare earth elements was studied by means of metallographic examination, scanning electron microscopic examination and mechanical property test. The experimental results show that heating temperature has great effect on impact toughness (α_k), bending fatigue (σ_(bb)) and relative toughness (σ_(bb)×f), but little effect on hardness (HRC). When the specimen was held at 960 ℃ for 3 h, it has better comprehensive mechanical properties, and the reason and regularity of the change for mechanical properties of the cast iron were reviewed.

Temperature-dependent evolution of oxide inclusions during heat treatment of stainless steel with yttrium addition

The evolution of oxide inclusions during isothermal heating of 18Cr–8Ni stainless steel with yttrium addition at temperatures of 1273 to 1573 K was investigated systematically.Homogeneous spherical Al–Y–Si(–Mn–Cr)oxide inclusions were observed in as-cast steel.After heating,most of the homogeneous inclusions were transformed into heterogeneous inclusions with Y-rich and Al-rich parts,even though some homogeneous oxide particles were still observed at 1273 and 1573 K.With the increase in heating temperature,more large-sized inclusions were formed.The shape of the inclusions also changed from spherical to irregular.The maximum transformation temperature of inclusions was determined to be 1373 K.The evolution mechanism of inclusions during heating was proposed to be the combined effect of the(i)internal transformation of inclusions due to the crystallization of glassy oxide and(ii)interfacial reaction between inclusions and steel matrix.Meanwhile,the internal transformation of inclusions was considered to be the main factor at heating temperatures less than 1473 K.

Formation Mechanism and Existing Form of Sb in Heat Resistance Mg-Gd-Y-Sb Alloy

The existing form and reaction mechanism of Sb in heat resistane Mg-Gd-Y-Sb rare earth magnesium alloy were investigated by inductive coupled plasma emission spectroscopy(ICP),scanning electron microscopy(SEM),energy dispersive spectroscopy(EDS),and X-ray diffraction(XRD).It is found that Sb tends to form high melting point intermetallics with rare earth elements of Gd and Y.The existing form of Sb is determined to be GdSb and SbY,respectively,which has high melting point(GdSb:2142℃/SbY:1782℃).Meanwhile,the first principle calculation and electronegativity difference calculation were performed to further understand the reaction mechanism.Therefore,the forming heat and binding energy were calculated.The experimental results show that the binding tendency of Sb element to Gd and Y is much stronger than that of it with other elements in this alloy,which results in the formation of high melting point of Gd-Sb and Y-Sb intermetallics,and finally leads to the high temperature resistant further improvement of the Mg-Gd-Y magnesium alloy.

Effect of Heat Treatment on the Microstructure and Corrosion Resistance of Cu-Zn Alloy

The microstructure of Cu-Zn alloy with different heat treatment conditions in 3.5%NaCl+NH3 solution were observed, and the average corrosion rates and electrochemical data of Cu-Zn alloy were measured, as well as the effect of heat treatment on microstructure and corrosion resistance of Cu-Zn alloy was analyzed. The results show that the microstructure of Cu-Zn alloy has been changed due to the heat treatment. As a results, the better corrosion resistance can be obtained for the Cu-Zn alloy quenched from 900 ℃ for 0.5 h followed by tempered at 100 ℃ for 2 h.