4种植物源性成分多重real-time PCR检测方法的建立及其在食用淀粉中的应用

建立一种可同时快速检测红薯、木薯、马铃薯、玉米源性成分的多重实时聚合酶链式反应(real-time polymerase chain reaction,real-time PCR)方法。分别以红薯g3pdh基因、木薯g3pdh基因、马铃薯UGPase基因、玉米zSSIIb基因为靶基因设计特异性引物和TaqMan探针,以18S rRNA基因为内参基因,建立多重real-time PCR方法,开展方法学验证,并对不同掺入比例模拟样品和实际淀粉样品进行检测。结果显示,该方法具有高通量、特异性强、灵敏度高等优点。与15种非目标源性均无交叉反应;对目标DNA的检测灵敏度可达到3×10^(-3) ng/μL,且具有良好的线性关系和扩增效率;对淀粉样品的检出限可达0.1%,对50份实际样品进行检测,结果与参比方法一致,说明建立的多重real-time PCR法可用于食用淀粉种类掺假鉴别检测。

Real-time Rescue Target Detection Based on UAV Imagery for Flood Emergency Response

Timely acquisition of rescue target information is critical for emergency response after a flood disaster.Unmanned Aerial Vehicles(UAVs)equipped with remote sensing capabilities offer distinct advantages,including high-resolution imagery and exceptional mobility,making them well suited for monitoring flood extent and identifying rescue targets during floods.However,there are some challenges in interpreting rescue information in real time from flood images captured by UAVs,such as the complexity of the scenarios of UAV images,the lack of flood rescue target detection datasets and the limited real-time processing capabilities of the airborne on-board platform.Thus,we propose a real-time rescue target detection method for UAVs that is capable of efficiently delineating flood extent and identifying rescue targets(i.e.,pedestrians and vehicles trapped by floods).The proposed method achieves real-time rescue information extraction for UAV platforms by lightweight processing and fusion of flood extent extraction model and target detection model.The flood inundation range is extracted by the proposed method in real time and detects targets such as people and vehicles to be rescued based on this layer.Our experimental results demonstrate that the Intersection over Union(IoU)for flood water extraction reaches an impressive 80%,and the IoU for real-time flood water extraction stands at a commendable 76.4%.The information on flood stricken targets extracted by this method in real time can be used for flood emergency rescue.

基于病菌孢子捕捉和real-time PCR技术的田间空气中小麦白粉病菌孢子动态监测及病情估计模型研究

利用Burkard定容式孢子捕捉器结合real-time PCR定量技术,分别对种植高抗、中感和高感白粉病小麦品种的田间空气中白粉病菌分生孢子浓度进行监测,结果表明,real-time PCR定量与传统的显微观察计数两种方法测得的孢子浓度呈显著正相关(P≤0.01),且两种病菌孢子计数方法在同一抗性品种上监测到的孢子浓度动态相近。此外,两种方法测得的孢子浓度与各气象因子的相关性分析结果一致,空气中的白粉病菌孢子浓度主要与空气相对湿度显著正相关。在此基础上,利用两种方法测定的田间空气中白粉病菌孢子浓度分别建立了基于累积孢子浓度的田间病情估计模型。分析发现,基于两种孢子浓度测定方法建立的病情估计模型间无显著性差异,表明real-time PCR定量技术测定的孢子浓度在构建白粉病病情估计模型上具有一定可行性。该结果为real-time PCR定量技术与病菌孢子捕捉技术相结合用于小麦白粉病的监测和预测提供理论依据。

马乳酒样乳杆菌马乳酒样亚种real-time PCR检测方法的建立与应用

本研究建立了一种特异性实时聚合酶链式反应(real-time polymerase chain reaction,real-time PCR)检测方法,根据模式菌株马乳酒样乳杆菌马乳酒样亚种ZW3的16S rDNA序列和全基因组序列设计筛选特异性引物,采用SYBR Green I荧光染料建立real-time PCR方法,并对方法的特异性、灵敏度、重复性和混合体系等进行检测。结果表明,本研究所建立的方法特异性强、灵敏度高、重复性好,建立real-time PCR的标准曲线,其决定系数R2为0.965,具有良好的线性关系,且在马乳酒样乳杆菌马乳酒样亚种及混合体系中可以特异性检出。综上,本研究建立的real-time PCR法可以快速、准确地检测马乳酒样乳杆菌马乳酒样亚种,为马乳酒样乳杆菌的特异性定性定量检测提供了一种新的方法。

基于Real-time PCR法检测乳粉中牛源性成分定量研究

基于Real-timePCR建立了乳粉中牛源性成分相对定量检测方法,并对牛的特异性引物与探针进行了特异性、灵敏度和稳定性测试。通过模拟不同浓度牛乳粉与马乳粉混合样本,根据其△Ct值的函数关系进行线性拟合进而绘制标准曲线,建立乳粉中牛源性成分的相对定量检测。结果显示,该方法的最低检测限为0.00001 mg/mL,回收率为91.11%~119.2%,组间变异系数≤0.58%、组内变异系数≤1.44%。说明该方法在特异性与稳定性上适用于乳粉中牛源性成分及含量的掺假检测。

一种基于real-time PCR技术的TTV检测方法的建立及应用

目的:本研究旨在开发一种具有更高灵敏度和特异性的TTV检测技术,为揭示TTV在多种疾病过程中的作用提供重要的技术支持。方法:为了更精确、灵敏的检测TTV,本研究分析了目前公布的所有亚型的TTV基因序列,在此基础上建立了一种基于UTR区域的real-time PCR检测方法,并与文献报道应用较为广泛的PCR检测方法进行了对比。结果:本研究建立的方法在1×10^(7)~1×10^(1) copies/μL标准品浓度范围内具有良好的线性关系,相关系数为1.000,斜率为-3.446,检测下限为1×10^(1) copies/μL。重复性试验结果显示,组内变异系数为7.22%,表明本方法重复性、稳定性较强。针对30份临床样本,使用本研究建立的real-time PCR检测方法及目前被多个研究所使用的4套引物进行对比。结果表明,本研究所建立的方法灵敏度显著高于文献中报道的4种方法(P<0.01);Sanger测序结果表明,本方法检测出的30份阳性样本均为TTV,检测特异性为100%。结论:本研究采用基于TaqMan探针的real-time PCR检测方法,检测灵敏性高、覆盖基因型范围广,尤其对于TTV病毒载量较低的情况下能够进行定量检测,对于TTV病毒的致病性及作为免疫标志物的应用提供重要的技术支持。

A Comparative Study between Landmark Based and Real Time Ultrasound Guided Sub Arachnoid Block

Background: Sub arachnoid block (SAB) performed by traditional landmark palpation technique can be inaccurate. This problem is exacerbated by altered patient anatomy due to obesity and age-related changes. A pre-procedural ultrasound scan of the lumbar spine has been shown to be of benefit in guiding lumbar epidural insertion in obstetric patients. Information on the use of real-time ultrasound (RUS) guided SAB, to date, been limited. This study compared RUS guided SAB to traditional landmark guided technique in patients undergoing spinal anesthesia for different surgical procedures. Methods: This was a prospective, single center, comparative observational study conducted in the department of anesthesiology at our center. 560 patients who underwent spinal anesthesia either by landmark based technique or real-time ultrasound-guided methods. The primary outcome was the first attempt success rate of dural puncture when employing the two methods. Results: Baseline characteristics were similar in the two study groups. The first attempt success rate of dural puncture in landmark guided group was 64.3% compared to 72.6% in the ultrasound guided group. This difference was not statistically significant. The procedure performance time was significantly shorter with landmark palpation compared to use of real-time ultrasound guided method. Conclusion: Use of RUS-guided technique does not significantly improve the first attempt success rate of SAB dural puncture during spinal anesthesia compared to the traditional landmark-guided technique.

Combined hybrid energy storage system and transmission grid model for peak shaving based on time series operation simulation

This study proposes a combined hybrid energy storage system(HESS) and transmission grid(TG) model, and a corresponding time series operation simulation(TSOS) model is established to relieve the peak-shaving pressure of power systems under the integration of renewable energy. First, a linear model for the optimal operation of the HESS is established, which considers the different power-efficiency characteristics of the pumped storage system, electrochemical storage system, and a new type of liquid compressed air energy storage. Second, a TSOS simulation model for peak shaving is built to maximize the power entering the grid from the wind farms and HESS. Based on the proposed model, this study considers the transmission capacity of a TG. By adding the power-flow constraints of the TG, a TSOS-based HESS and TG combination model for peak shaving is established. Finally, the improved IEEE-39 and IEEE-118 bus systems were considered as examples to verify the effectiveness and feasibility of the proposed model.

24重荧光real-time PCR技术在食物中毒快速检测中的应用

目的:应用24重荧光real-time PCR检测技术快速筛检食物中毒病原菌,结合国家标准中的培养法探讨24重荧光real-time PCR检测技术符合性和应用价值。方法:采用高灵敏度、高特异性的24重荧光real-time PCR检测技术作为中毒病原菌的初筛方法,国标方法进行细菌分离培养,并对分离出的病原菌进行生化鉴定。结果:5份食物中毒患者肛拭子在增菌前检出4份霍乱弧菌核酸(非O1/非O139群,24重荧光real-time PCR),9份患者肛拭子在增菌后检出5株霍乱弧菌(非O1/非O139群,国标培养法),其中包含4份PCR技术初筛阳性样品,两个方法的符合率为80%。所有样本均未检出沙门氏菌、志贺菌、副溶血性弧菌、致泻性大肠埃希菌以及金黄色葡萄球菌。结论:应用24重荧光real-time PCR检测技术同时检测24种常见致病病原菌,能高效锁定中毒病原菌。将其与国标培养法相结合,对临床治疗和食物中毒快速处置能起到积极作用,值得应用和推广。

Real-Time Monitoring of Meteorological Data at In-Situ GCW Remediation Sites

To optimize the self-organization network, self-adaptation, real-time monitoring, remote management capability, and equipment reuse level of the meteorological station supporting the portable groundwater circulation wells, and to provide real-time and effective technical services and environmental data support for groundwater remediation, a real-time monitoring system design of the meteorological station supporting the portable groundwater circulation wells based on the existing equipment is proposed. A variety of environmental element information is collected and transmitted to the embedded web server by the intelligent weather transmitter, and then processed by the algorithm and stored internally, displayed locally, and published on the web. The system monitoring algorithm and user interface are designed in the CNWSCADA development environment to realize real-time processing and analysis of environmental data and monitoring, control, management, and maintenance of the system status. The PLC-controlled photovoltaic power generating panels and lithium battery packs are in line with the concept of energy saving and emission reduction, and at the same time, as an emergency power supply to guarantee the safety of equipment and data when the utility power fails to meet the requirements. The experiment proves that the system has the characteristics of remote control, real-time interaction, simple station deployment, reliable operation, convenient maintenance, and green environment protection, which is conducive to improving the comprehensive utilization efficiency of various types of environmental information and providing reliable data support, theoretical basis and guidance suggestions for the research of groundwater remediation technology and its disciplines, and the research and development of the movable groundwater cycling well monitoring system.

垂体后叶粉中3种动物源性成分多重real-time PCR检测方法的建立及应用

目的基于三重实时聚合酶链式反应(real-time polymerase chain reaction,real-time PCR)技术同时快速检测垂体后叶粉中的猪、牛、羊性动物源性成分。方法采用CTAB法提取样品及对照品DNA,以线粒体基因为靶基因设计并合成三重real-time PCR的引物探针,并对建立方法进行验证,用于检测垂体后叶粉样品是否与标识一致。结果猪、牛、羊源性成分的最低检测浓度为10 pg/μL,采用建立的方法检测3批垂体后叶粉样品,均只检测出猪源性成分。结论建立的方法可用于同时检测垂体后叶粉中的猪、牛、羊源性成分,可为相关工作提供技术支持。

A CNN-Based Single-Stage Occlusion Real-Time Target Detection Method

Aiming at the problem of low accuracy of traditional target detection methods for target detection in endoscopes in substation environments, a CNN-based real-time detection method for masked targets is proposed. The method adopts the overall design of backbone network, detection network and algorithmic parameter optimisation method, completes the model training on the self-constructed occlusion target dataset, and adopts the multi-scale perception method for target detection. The HNM algorithm is used to screen positive and negative samples during the training process, and the NMS algorithm is used to post-process the prediction results during the detection process to improve the detection efficiency. After experimental validation, the obtained model has the multi-class average predicted value (mAP) of the dataset. It has general advantages over traditional target detection methods. The detection time of a single target on FDDB dataset is 39 ms, which can meet the need of real-time target detection. In addition, the project team has successfully deployed the method into substations and put it into use in many places in Beijing, which is important for achieving the anomaly of occlusion target detection.

Real-time performance of periodic data transmission in EPA industrial Ethernet

To evaluate and improve the real-time performance of Ethernet for plant automation（EPA） industrial Ethernet,the real-time performance of EPA periodic data transmission was theoretically and experimentally studied.By analyzing information transmission regularity and EPA deterministic scheduling mechanism,periodic messages were categorized as different modes according to their entering-queue time.The scheduling characteristics and delivery time of each mode and their interacting relations were studied,during which the models of real-time performance of periodic information transmission in EPA system were established.On this basis,an experimental platform is developed to test the delivery time of periodic messages transmission in EPA system.According to the analysis and the experiment,the main factors that limit the real-time performance of EPA periodic data transmission and the improvement methods were proposed.

Modeling and Statistical Properties Research on Online Real-Time Information Transmission Network

In this paper, the model of the online real-time information transmission network, such as wechat, micro-blog, and QQ network, is proposed and built, based on the connection properties between users of the online real-time information transmission network, and combined with the local world evolving characteristics in complex network, then the statistical topological properties of the network is obtained by numerical simulation. Furthermore, we simulated the process of information transmission on the network, according to the actual characteristics of the online real-time information transmission. Statistics show that the degree distribution presents the characteristics of scale free network, presenting power law distribution, while the average path length, the average clustering coefficient and the average size of the network also has a power-law relationship, moreover, the model parameters has no effect on power-law exponent. The spread of information on the network represents obvious fluctuation scaling, reflecting the characteristics that information transmission fluctuates over time.

Real-time Audio &Video Transmission System Based on Visible Light Communication

With the increasing popularity of solid sate lighting devices, Visible Light Communication (VLC) is globally recognized as an advanced and promising technology to realize short-range, high speed as well as large capacity wireless data transmission. In this paper, we propose a prototype of real-time audio and video broadcast system using inexpensive commercially available light emitting diode (LED) lamps. Experimental results show that real-time high quality audio and video with the maximum distance of 3 m can be achieved through proper layout of LED sources and improvement of concentration effects. Lighting model within room environment is designed and simulated which indicates close relationship between layout of light sources and distribution of illuminance.

Multi-parameter real-time monitoring scheme for power transmission lines based on FBG sensors

A multi-parameter real-time monitoring scheme for power transmission line is proposed and experimentally demonstrated.The Fiber Bragg Grating(FBG)sensors are used to sensing the information of temperature and strain in the power transmission lines system,and a monitoring center based on client–server model is established to process and display the sensing information.Several FBG-based power transmission line temperature sensors interrogated based on the developed multi-parameter real-time monitoring scheme is experimentally investigated.The result shows that the system is very useful.

4种动物源性成分多重real-time PCR检测方法的建立及其在驴肉制品检测中的应用

建立一种同时快速检测驴、马、猪及鸭源性成分的四重实时聚合酶链式反应(real-time polymerase chain reaction,real-time PCR)方法。分别以4种源性成分的Nad5、ATpase6、ATP8、cytb基因为靶基因设计特异性引物和TaqMan探针,以18S rRNA基因为内参基因,建立多重real-time PCR方法,并对该方法进行方法学验证,同时对不同掺入比例模拟样品、不同加工工艺模拟样品和实际驴肉样品进行检测。结果显示,该方法具有高通量、特异性强、灵敏度高等优点。当Ct值≤35.0时,方法对16种非目标源性具有良好特异性;灵敏度可检测到质量浓度为2×10^(-4)ng/μL的模板DNA;对生肉的检出限为肉含量的0.001%,对熟肉制品的检出限为肉含量的0.01%;对100份实际样品进行检测,结果与标准方法一致,说明建立的多重real-time PCR法可用于肉及肉制品中常见掺假源性成分的检测。

A real time transmission system of long distance for nuclear logging

Some specified chips in traditional Manchester-Ⅱencoding/decoding designs are used to guarantee strictly the stability of the input wave,otherwise the capacity of anti-interference and resilience are degraded seriously.In this paper,a new Manchester-Ⅱencoding/ decoding system is used for nuclear logging by a 7 000 m armoring cable.A thorough hardware wave tracking decoding algorithm is proposed and realized in a FPGA hardware chip.An on-site measurements show that this transmission system can decode correctly in real time,with a bit error rate of better than 10^(-10).

肉中猪源性成分Real-time PCR定量检测技术

【目的】建立一种快速、准确的肉中猪源性成分定量检测方法。【方法】首先从GenBank数据库中筛选猪特异性的微卫星DNA,根据微卫星DNA核酸序列设计引物,对常见10种动物基因组DNA进行PCR扩增,通过有无扩增产物判断筛选的微卫星DNA对猪源性成分的特异性。然后根据微卫星DNA核酸序列,设计特异性引物和探针,建立猪源性成分Real-time PCR检测方法,采用双标准曲线分别对猪源性成分和总动物源性成分进行定量,计算猪源性成分的百分含量。【结果】筛选到猪特异性微卫星DNA(Accession EF172428),根据其序列设计的引物SEQ-sus2-F/R只能从猪基因组DNA中扩增出目的条带,其他动物的基因组均无目的条带扩增。建立的Real-time PCR检测方法灵敏度为0.02 ng/25μL反应体系。该方法能够准确检测出混合DNA样品中猪源性成分和混合肉样品中猪源性成分,百分误差分别约为1.32%和1.06%-7.12%。【结论】本研究利用Real-time PCR技术建立的定量猪源性成分的检测方法可以用来检测猪源性成分在混合样品中的百分含量。

Transmission Considerations with QoS Support to Deliver Real-Time Distributed Speech Recognition Applications

Distributed speech recognition (DSR) applications have certain QoS (Quality of service) requirements in terms of latency, packet loss rate, etc. To deliver quality guaranteed DSR application over wirelined or wireless links, some QoS mechanisms should be provided. We put forward a RTP/RSVP transmission scheme with DSR-specific payload and QoS parameters by modifying the present WAP protocol stack. The simulation result shows that this scheme will provide adequate network bandwidth to keep the real-time transport of DSR data over either wirelined or wireless channels.