Applied Research of the Inner Timer of General Microcomputer in High-Speed and Real-Time Data Acquisition System

The real-time data acquisition system controlled by microcomputer is applied widely. It is very important how to use the inner timer of microcomputer to realize accurate timing of sampling-interval in the application of data acquisition. This paper discusses in detail the procedure that we use the inner timer of microcomputer to realize real-time data acquisition with high timing-accuracy, and analyze the error of timing-accuracy. It also gives us a relevant routine programmed in assembly language.

High-SpeedReal-TimeDataAcquisitionSystem Realized by Interleaving/Multiplexing Technique

The interleaving/multiplexing technique was used to realize a 200?MHz real time data acquisition system. Two 100?MHz ADC modules worked parallelly and every ADC plays out data in ping pang fashion. The design improved the system conversion rata to 200?MHz and reduced the speed of data transporting and storing to 50?MHz. The high speed HDPLD and ECL logic parts were used to control system timing and the memory address. The multi layer print board and the shield were used to decrease interference produced by the high speed circuit. The system timing was designed carefully. The interleaving/multiplexing technique could improve the system conversion rata greatly while reducing the speed of external digital interfaces greatly. The design resolved the difficulties in high speed system effectively. The experiment proved the data acquisition system is stable and accurate.

Design and implementation of high-speed real-time data acquisition system based on FPGA

The electromagnetic radiation will result in informa- tion leakage being recovered when computers work. This article presents a high-speed real-time data acquisition system based on peripheral component interconnect （PCI） bus and field programmable gate array （FPGA） for sampling electromagnetic radiation caused by video signal. The hardware design and controlling flow of each module are introduced in detail. The sampling rate can reach 64 Msps and system transfers speed can be up to 128 Mb/s by using time interleaving, which increases the overall sampling speed of a system by operating two data converters in parallel.

Alternate Data Acquisition and Real-time Monitoring System on HT-7 Tokamak

A new system called alternate data acquisition and real-time monitoring system has been developed for long-time discharge in tokamak operation. It can support continuous on-line data acquisition at a high sampling rate and a graphic display of the plasma parameters during the discharge. Thus operators can monitor and control the plasma state in real time. An application of this system has been demonstrated on the HT-7 tokamak.

Embedded Data Acquisition in Vehicle Electronic System

The embedded data acquistition technology in vehicle electronic system was discussed. This technology adopts the parallel working mode, gets vehicle electronic system data by communication. This technology can provide us a lot of information on the electronic control unit, is very useful for the development of the vehicle electronic system, and can be used in diagnosis. The key points to this technology are the timer interrupt, A/D interrupt, communication interrupt and real time operation. This technology has been validated by the application in the electronic control mechanism transmission shifting system of the tank.

Design of multi-channel data acquisition system based on LabVIEW and NI PXI-5105

A data acquisition system based on LabVIEW and NI PXI-5105 is presented for multi-channel data acquisition. It can realize the functions of parameter setting, data acquisition and storage, waveform display and data analysis using LabVIEW and NI-SCOPE device driver. The advantages of the system are that the setting is convenient, the operation is easy, the interface is friendly and the functions are practical. The experiment results show that the system has good stability and high reliability and is a powerful tool for multi-channel data acquisition.

On-Board Data Acquisition System for Automatic Shift System of Vehicle

Data acquisition, analysis and calibrating system affiliated with the vehicle is developed for the research on the automatic shift system (ASS). Considering the vehicle’s hard environment such as vibration, high and low temperature, electromagnetic disturbance and so on, the most suitable project is selected. PC104 transfers data with ECU by serial communication and a solid state disk is used as a FLASH ROM. Some techniques including frequency division of data is adopted in the software design in order to ensure the sampling frequency. The analysis and debug software is also contrived according to the characteristic of the ASS. The system plays an important role in the development of the ASS because of the good reliability and practicability in the application.

Quality control of marine big data——a case study of real-time observation station data in Qingdao

Offshore waters provide resources for human beings,while on the other hand,threaten them because of marine disasters.Ocean stations are part of offshore observation networks,and the quality of their data is of great significance for exploiting and protecting the ocean.We used hourly mean wave height,temperature,and pressure real-time observation data taken in the Xiaomaidao station(in Qingdao,China)from June 1,2017,to May 31,2018,to explore the data quality using eight quality control methods,and to discriminate the most effective method for Xiaomaidao station.After using the eight quality control methods,the percentages of the mean wave height,temperature,and pressure data that passed the tests were 89.6%,88.3%,and 98.6%,respectively.With the marine disaster(wave alarm report)data,the values failed in the test mainly due to the influence of aging observation equipment and missing data transmissions.The mean wave height is often affected by dynamic marine disasters,so the continuity test method is not effective.The correlation test with other related parameters would be more useful for the mean wave height.

The development of data acquisition and processing application system for RF ion source

As the key ion source component of nuclear fusion auxiliary heating devices, the radio frequency （RF） ion source is developed and applied gradually to offer a source plasma with the advantages of ease of control and high reliability. In addition, it easily achieves long-pulse steady-state operation. During the process of the development and testing of the RF ion source, a lot of original experimental data will be generated. Therefore, it is necessary to develop a stable and reliable computer data acquisition and processing application system for realizing the functions of data acquisition, storage, access, and real-time monitoring. In this paper, the development of a data acquisition and processing application system for the RF ion source is presented. The hardware platform is based on the PXI system and the software is programmed on the LabVIEW development environment. The key technologies that are used for the implementation of this software programming mainly include the long-pulse data acquisition technology, multi- threading processing technology, transmission control communication protocol, and the Lempel-Ziv-Oberhumer data compression algorithm. Now, this design has been tested and applied on the RF ion source. The test results show that it can work reliably and steadily. With the help of this design, the stable plasma discharge data of the RF ion source are collected, stored, accessed, and monitored in real-time. It is shown that it has a very practical application significance for the RF experiments.

Development of a Data Acquisition Control System for the First NBI on EAST

Neutral beam injection （NBI） heating is one of the most efficient auxiliary plasma heating methods for fusion devices. The data acquisition control system （DACS） with PXI （pe- ripheral component interconnect extensions for instrumentation） data acquisition card for the first NBI system in the experimental advanced superconducting tokamak （EAST） is presented in this paper. As an important sub-system, DACS is designed to obtain physical measurement signals in the EAST NBI system and to deal and store these data with the Lempel-Ziv-Oberhumer （LZO） lossless data compression algorithm, as well as offer convenient data call-back and access inter- faces to the user for examining and analyzing the data. Experimental results show that accurate data will ensure that researchers correctly analyze it and then properly adjust the experimental parameters or operation, so DACS should take a large step in improving experimental efficiency. Tile hardware and software sections are briefly presented in this paper, and now this system has been tested to be able to work reliably and steadily.

Design and implementation of 1 GHz high speed data acquisition system

With the development of current electronic technology, numerous high-speed data acquisition systems provide a variety of potential benefits. This article describes a high-speed data acquisition system which consists of ECL logic and TTL logic devices, samples and stores data with a 1 GHz clock. This system is accomplished easily and works stably. A performance test of this system has been undertaken and the results show that the effective number of bits （ENOB） is more than 6.5 bits.

On the Study of Multi-Gas Data Acquisition System Based on PCI1711 Card

A data acquisition system for testing gas sensor array response to multi-gas is presented.The testing system is based on the character of the gas response of metal oxide semiconductor gas sensor array.The data acquisition is realized automatically through the real time controlling of the data acquisition card PCI1711.This system is highly attractive for electronic nose,which is a powerful tool for the discrimination of gases.

Data network traffic analysis and optimization strategy of real-time power grid dynamic monitoring system for wide-frequency measurements

The application and development of a wide-area measurement system(WAMS)has enabled many applications and led to several requirements based on dynamic measurement data.Such data are transmitted as big data information flow.To ensure effective transmission of wide-frequency electrical information by the communication protocol of a WAMS,this study performs real-time traffic monitoring and analysis of the data network of a power information system,and establishes corresponding network optimization strategies to solve existing transmission problems.This study utilizes the traffic analysis results obtained using the current real-time dynamic monitoring system to design an optimization strategy,covering the optimization in three progressive levels:the underlying communication protocol,source data,and transmission process.Optimization of the system structure and scheduling optimization of data information are validated to be feasible and practical via tests.

Real-Time Intelligent Diagnosis of Co-frequency Vibration Faults in Rotating Machinery Based on Lightweight-Convolutional Neural Networks

The co-frequency vibration fault is one of the common faults in the operation of rotating equipment,and realizing the real-time diagnosis of the co-frequency vibration fault is of great significance for monitoring the health state and carrying out vibration suppression of the equipment.In engineering scenarios,co-frequency vibration faults are highlighted by rotational frequency and are difficult to identify,and existing intelligent methods require more hardware conditions and are exclusively time-consuming.Therefore,Lightweight-convolutional neural networks(LW-CNN)algorithm is proposed in this paper to achieve real-time fault diagnosis.The critical parameters are discussed and verified by simulated and experimental signals for the sliding window data augmentation method.Based on LW-CNN and data augmentation,the real-time intelligent diagnosis of co-frequency is realized.Moreover,a real-time detection method of fault diagnosis algorithm is proposed for data acquisition to fault diagnosis.It is verified by experiments that the LW-CNN and sliding window methods are used with high accuracy and real-time performance.

Data Acquisition System for Electron Energy Loss Coincident Spectrometers

A Data Acquisition System （DAQ） for electron energy loss coincident spectrometers （EELCS） has been developed. The system is composed of a Multiplex Time-Digital Converter （TDC） that measures the flying time of positive and negative ions and a one-dimension positionsensitive detector that records the energy loss of scattering electrons. The experimental data are buffered in a first-in-first-out（FIFO） memory module, then transferred from the FIFO memory to PC by the USB interface. The DAQ system can record the flying time of several ions in one collision, and allows of different data collection modes. The system has been demonstrated at the Electron Energy Loss Coincident Spectrometers at the Laboratory of Atomic and Molecular Physics, USTC. A detail description of the whole system is given and experimental results shown.

Performance of digital data acquisition system in gamma-ray spectroscopy

A newly developed digital data acquisition system,which is based on the digital pulse processor Pixie-16 modules by XIA LLC,was tested with the c-ray detector array of the China Institute of Atomic Energy using the cray source and in-beam c-rays.A comparison between this digital data acquisition system and the conventional analog data acquisition system was made.At a low count rate,both systems exhibit good and comparable energy resolutions.At a high count rate above 8.8 k/s,while the energy resolution obtained by the analog system deteriorates significantly,the energy resolution obtained by the digital system is nearly unchanged.Meanwhile,experimental data with higher statistics can be collected by the digital system.The advantage of this digital system over the conventional analog system can be ascribed to its excellent capability of handling pile-up pulses at higher count rates,and the fact that it has nearly no dead time in data transmission and conversion.

High Sensitivity Acquisition Algorithm for DSSS Signal with Data Modulation

In direct sequence spread spectrum communication both for satelliteto-ground and inter-satellite links, the system constrains due to radio frequency spectral occupation, channel data throughput and link performances in terms of data channel coding which might result in a signal structure where the symbol duration is shorter than the pseudo code period. This can generate some difficulties in the DSSS signal acquisition due to the polarity inversion caused by the data modulation. To eliminate the influence due to polarity inversion, this paper proposes a novel acquisition algorithm based on the simultaneous search of the code phase, data phase and Doppler frequency. In the proposed algorithm the data phase is predicted and the correlation period for the coherent integration can be set equal to the symbol duration. Then non-coherent accumulation over different symbol is implemented in order to enhance the acquisition algorithm sensitivity; the interval of non-coherent accumulation is the least common multiple between the symbol duration and the pseudo code period. The algorithm proposed can largely minimize the SNR loss caused by data polarity inversion and enhance acquisition performance without a noticeable increase in hardware complexity. Theoretical analysis, simulation and measured results verify the validity of the algorithm.

Development and Integration of a Data Acquisition System for SST-1 Phase-1 Plasma Diagnostics

Long pulse （of the order of 1000 s or more） SST-1 tokamak experiments demand a data acquisition system that is capable of acquiring data from various diagnostics channels without losing useful data （and hence physics information） while avoiding unnecessary generation of a large volume data. SST-1 Phase-1 tokamak operation has been envisaged with data acquisition of several essential diagnostics channels. These channels demand data acquisition at a sampling rate ranging from 1 kilo samples per second （KSPS） to 1 mega samples per second （MSPS）. Considering the technical characteristics and requirements of the diagnostics, a data acquisition system based on PXI and CAMAC has been developed for SST-1 plasma diagnostics. Both these data acquisition systems are scalable. Present data acquisition needs involving slow plasma diagnostics are catered by the PXI based data acquisition system. On the other hand, CAMAC data acquisition hardware meets all requirements of the SST-1 Phase-1 fast plasma diagnostics channels. A graphical user interface for both data acquisition systems （PXI and CAMAC） has been developed using LabVIEW application development software. The collected data on the local hard disk are directly streaming to the central server through a dedicated network for post-shot data analysis. This paper describes the development and integration of the data acquisition system for SST-1 Phase-1 plasma diagnostics. The integrated testing of the developed data acquisition system has been performed using SST-1 central control and diagnostics signal conditioning units. In the absence of plasma shots, the integrated testing of the data acquisition system for the initial diagnostics of SST-1 Phase-1 operation has been performed with simulated physical signals. The primary engineering objective of this integrated testing is to validate the performance of the developed data acquisition system under simulated conditions close to that of actual tokamak operation. The data acquisition is synchronized with a clock and trigger provided by the central timing system.

A Real-time Lithological Identification Method based on SMOTE-Tomek and ICSA Optimization

In petroleum engineering,real-time lithology identification is very important for reservoir evaluation,drilling decisions and petroleum geological exploration.A lithology identification method while drilling based on machine learning and mud logging data is studied in this paper.This method can effectively utilize downhole parameters collected in real-time during drilling,to identify lithology in real-time and provide a reference for optimization of drilling parameters.Given the imbalance of lithology samples,the synthetic minority over-sampling technique(SMOTE)and Tomek link were used to balance the sample number of five lithologies.Meanwhile,this paper introduces Tent map,random opposition-based learning and dynamic perceived probability to the original crow search algorithm(CSA),and establishes an improved crow search algorithm(ICSA).In this paper,ICSA is used to optimize the hyperparameter combination of random forest(RF),extremely random trees(ET),extreme gradient boosting(XGB),and light gradient boosting machine(LGBM)models.In addition,this study combines the recognition advantages of the four models.The accuracy of lithology identification by the weighted average probability model reaches 0.877.The study of this paper realizes high-precision real-time lithology identification method,which can provide lithology reference for the drilling process.

Design of Gamma Spectrum Data Acquisition and Processing System Based on ARM / DSP

Research for detecting or obtaining radionuclide by gamma energy spectrum data acquisition and process system is one of the key issues about intelligent measurement of gamma-ray spectrum. For this reason, a software and hardware implementation schematic design based on ARM ( Advanced RISC Machines) + DSP ( Digital Signal Processor) architecture for gamma energy spectrum data acquisition and processing system is proposed. The paper discusses in detail some key technologies such as communication interface design between microcontroller ARM and digital signal processor DSP,distribution scheduling under multi-task in the ARM-Linux,DSP handling procedures for multi-channel A / D high-speed sample. At the same time,because the traditional Gaussian fitting to determine the boundary of peak is not ideal,it puts forward a weighting factor of Gaussian function least squares fitting realize boundary determined. Finally gamma-spectrum data from sodium iodide NaI( TI) scintillation detector is tested and processed in the new system. The results show that gamma energy spectrum data acquisition and process system is perfect functionality, stable and convergence in unimodal. Compared with data from conventional energy spectrometers,the system can keep better energy resolution in a wide range of pulse pass rate.