Progress in developing self-consolidating concrete(SCC)constituting recycled concrete aggregates:A review

Recycled concrete aggregate(RCA)derived from demolition waste has been widely explored for use in civil engineering applications.One of the promising strategies globally is to incorporate RCA into concrete products.However,the use of RCA in high-performance concrete,such as self-consolidating concrete(SCC),has only been studied in the past decade.This paper summarizes recent publications on the use of coarse and/or fine RCA in SCC.As expected,the high-water absorption and porous structure of RCA have posed challenges in producing a high-fluidity mixture.According to an analysis of published data,a lower strength reduction(within 23%regardless of coarse RCA content)is observed in SCC compared with vibrated concrete,possibly due to the higher paste content in the SCC matrix,which enhances the weak surface layer of RCA and interfacial transition zone.Similarly,SCC tends to become less durable with RCA substitution although the deterioration can be minimized by using treated RCA through removing or strengthening the adhered mortar.To date,the information reported on the role of RCA in the long-term performance of SCC is still limited;thus,a wide range of research is needed to demonstrate the feasibility of RCA–SCC in field applications.

Microbial-inspired self-healing of concrete cracks by sodium silicate-coated recycled concrete aggregates served as bacterial carrier

Microbially induced carbonate precipitation(MICP)is a promising technique for the autonomous healing of concrete cracks.In this study,the effect of pH on MICP was investigated.The results indicate that the MICP process was inhibited when the pH was higher than 11.Both vaterite and calcite were produced when the pH was<8,whereas only calcite was produced when the pH was>8.Recycled concrete aggregates(RCA)coated with sodium silicate have been proposed as protective carriers for microbial healing agents.Although the presence of the coated RCA resulted in a loss of the splitting tension strength of the concrete,the loaded healing agents were highly efficient in self-healing cracks.Concrete incorporated with 20%RCA loaded with healing agents exhibited the best self-healing performance.When the initial crack widths were between 0.3 and 0.4 mm,the 7-d mean healing rate was approximately 90%.At 28 d,the crack area filling ratio was 86.4%,while its water tightness recovery ratio was 74.4%and 29.8%,respectively,for rapid and slow absorption.This study suggests that RCA coated with sodium silicate is an effective method for packaging microbial healing agents and has great potential for developing cost-effective self-healing concrete.

Use of recycled concrete aggregates in asphalt mixtures for pavements:A review

Large quantities of natural aggregates(NA)are required in the manufacturing of asphalt mixtures for pavements.The extraction of NA generates high environmental impacts that negatively affect environmental preservation and conservation.Diverse alternative materials obtained in construction and demolition processes in civil construction worked have been studies as possible replacements for NA,with the purpose of reducing these environmental impacts.The foregoing study presents a state of knowledge review referring to the use of recycled concrete aggregates(RCA)when these are used in the manufacturing of asphalt mixtures(mainly hot-mix asphalt HMA type).Environmental aspects are presented,as well as possible benefits and limitations of using RCA as replacements for NA in asphalt mixtures.However,it is not possible to establish a behavior pattern,since the characteristics of the RCA are very heterogeneous and vary from the original source of the concrete.It is highlighted from the literature that RCA has a wide potential for use in the manufacture of asphalt mixtures,since in most studies,the mixtures with these materials comply the quality requirements contemplated by the construction specifications,mainly in low-volume roads.Additionally,based on the literature review,some recommendations and suggestions are presented for future research.

Effect of Modification Treatment on Chloride Ions Permeability and Microstructure of Recycled Brick-mixed Aggregate Concrete

The modification methods of pozzolan slurry combined with sodium silicate and silicon-based additive were respectively adopted to treat recycled coarse brick-mixed aggregate(RCBA)in this study.The compressive strength and chloride permeability resistance of recycled aggregate concrete(RAC)before and after modification treatment were tested,and the microstructure of RAC was analyzed by mercury intrusion porosimetry(MIP)and scanning electron microscopy(SEM).The results show that the physical properties of RCBA strengthened by modification treatment are improved,and the compressive strength and chloride permeability resistance of treated RAC are also significantly improved.The modification treatment optimizes the pore size distribution of RAC,which increases the number of gel pores and transition pores,and decreases the number of capillary pores and macro pores.The surface fractal dimension shows a significant correlation with chloride diffusion coefficient,indicating that the variation of chloride permeability of treated RAC is consistent with the microstructure evolution.

Effect of Aggregate Gradation on the Properties of 3D Printed Recycled Coarse Aggregate Concrete

A simplex centroid design method was employed to design the gradation of recycled coarse aggregate.The bulk density was measured while the specific surface area and average excess paste thickness were calculated with different gradations.The fluidity,dynamic yield stress,static yield stress,printed width,printed inclination,compressive strength and ultrasonic wave velocity of 3D printed recycled aggregate concrete(3DPRAC)were further studied.The experimental results demonstrate that,with the increase of small-sized aggregate(4.75-7 mm)content,the bulk density initially increases and then decreases,and the specific surface area gradually increases.The average excess paste thickness fluctuates with both bulk density and specific surface area.The workability of 3DPRAC is closely related to the average excess paste thickness.With an increase in average paste thickness,there is a gradual decrease in dynamic yield stress,static yield stress and printed inclination,accompanied by an increase in fluidity and printed width.The mechanical performance of 3DPRAC closely correlates with the bulk density.With an increase in the bulk density,there is an increase in the ultrasonic wave velocity,accompanied by a slight increase in the compressive strength and a significant decrease in the anisotropic coefficient.Furthermore,an index for buildability failure of 3DPRAC based on the average excess paste thickness is proposed.

Multi-Scale Investigation on Concrete Prepared with Recycled Aggregates from Different Parent Concrete

Recycled aggregates(RA)are frequently obtained from various unknown sources,which caused variation in properties among recycled aggregates concrete(RAC).This paper investigated the macro and microscopic properties of RAC prepared with RAs originated from different parent concretes with 90-day strength ranging from 30 MPa to 100 MPa.These parent concretes were prepared in advance and crushed to produce RA of distinct qualities.The attached mortar content can reach up to 69%in the concrete with highest strength grade.The microscopic investigation on different RAC was conducted with the X-ray Micro-Computed Tomography scanning technique and image process.Experimental results showed that the properties of RA derived from various parent concrete varied because of the amount of residual mortar.The development of mechanical properties and chloride-ion penetration of RACs all followed a binomial trend with the strength grades of the parent concrete because of the different quantity and quality of RAs.

The Compression-deformation Behaviour of Concrete with Various Modified Recycled Aggregates

Modified recycled aggregates were prepared with three different cement-admixture grouts. The physical properties, such as water absorption, apparent density, crushing index, slump and compressive strength of the recycled aggregate and the recycled concretes were tested, and the tests for the compression-deformation behavior of the concretes were also performed. The experimental results show that the cement-Kim powder grout is satisfied for enhancing the recycled concrete, and the modification of the recycled aggregate with the grouts can improve the toughness and the deformation ability of the concretes.

Study on Durability of Recycled Aggregate Concrete in High-Temperature and Complex Environments

Recycled aggregate concrete refers to a new type of concrete material made by processing waste concrete materials through grading,crushing,and cleaning,and then mixing them with cement,water,and other materials in a certain gradation or proportion.This type of concrete is highly suitable for modern construction waste disposal and reuse and has been widely used in various construction projects.It can also be used as an environmentally friendly permeable brick material to promote the development of modern green buildings.However,practical applications have found that compared to ordinary concrete,the durability of this type of concrete is more susceptible to high-temperature and complex environments.Based on this,this paper conducts theoretical research on its durability in high-temperature and complex environments,including the current research status,existing problems,and application prospects of recycled aggregate concrete’s durability in such environments.It is hoped that this analysis can provide some reference for studying the influence of high-temperature and complex environments on recycled aggregate concrete and its subsequent application strategies.

Experimental Study on Mechanical Properties of Self-Compacting Recycled Concrete

The application of self-compacting recycled concrete can solve the problem of environmental pollution caused by construction waste but its mechanical properties have not been unified and need further study.The strength of recycled concrete is unstable,and its performance still needs further study.The combination of fixed sand and stone volume method and free water cement ratio method is used to determine the mix ratio of self-compacting recycled concrete.24 sets of slump expansion tests and 24 sets of cube axial compression tests were carried out to study the effect of recycled aggregate replacement rate on the flow performance and axial compressive strength of self-compacting recycled concrete,and the performance conversion formula of self-compacting recycled concrete was given.The results show that with the increase of the regenerated coarse aggregate substitution rate,the fluidity and filling property of the self-compacting regenerated concrete mix decreased.The failure of self-compacting recycled concrete is mainly due to the failure of strength between old mortar and new mixture.As the substitution rate increases from 0 to 100%,the axial compressive strength decreases by 15.2%.

Three-Dimensional Multi-Phase Microscopic Simulation of Service Life of Recycled Large Aggregate Self-Compacting Concrete

Recycled large aggregate self-compacting concrete (RLA-SCC) within multiple weak areas. These weak areas have poor resistance to chloride ion erosion, which affects the service life of RLA-SCC in the marine environment. A three-dimensional multi-phase mesoscopic numerical model of RLA-SCC was established to simulate the chloride ions transportation in concrete. Experiments of RLA-SCC immersing in chloride solution were carried out to verify the simulation results. The effects of recycled large aggregate (RLA) content and RLA particle size on the service life of concrete were explored. The results indicate that the mesoscopic numerical simulation results are in good agreement with the experimental results. At the same depth, the closer to the surface of the RLA, the greater the chloride ion concentration. The service life of RLA-SCC in marine environment decreases with the increase of RLA content. Compared with the service life of 20% content, the service life of 25% and 30% content decreased by 20% and 42% respectively. Increasing the particle size of RLA can effectively improve the service life of RLA-SCC in chloride environment. Compared with the service life of 50 mm particle size, the service life of 70 mm and 90 mm increased by 61% and 163%, respectively. .

Effect of waste concrete with different strength on mechanical properties of recycled fine aggregate mortar

The influence of source concrete (SC) with different compression strengths on the workability and mechanical properties of recycled mortar made with river sand substituted by 100% fine recycled concrete aggregates (FRCA) is experimentally investigated. The basic physical performance test shows that with the increase in SC strength, FRCA exhibit lower water absorption and crushing index, meanwhile keeping higher densities. Mechanical property tests, including compressive strength, flexural strength and uniaxial compressive stress-strain tests, show that compressive strength,flexural strength and elasticity modulus of recycled sand mortars increase roughly with the increase in SC strength. The proposed mixture design method demonstrates that all of the components can be kept as the same as those in natural mortar mixture design and FRCA must be pre-wetted before making mortar mixture. Meanwhile, the reuse of higher strength SC can ensure that recycled mortar mixtures are able to achieve similar mechanical performance when compared to natural mortar designs.

Compressive Strength, Pore Size Distribution and Chloride-ion Penetration of Recycled Aggregate Concrete Incorporating Class-F Fly Ash

The effects of fly ash on the compressive strength, pore size distribution and chloride-ion penetration of recycled aggregate concrete were investigated. Two series of concrete mb：tures were prepared. The concrete mixtures in series I had a water-to-binder ratio and a cement content of 0.55 and 410 kg/ m^3 , respectively. The concrete rnixtures in series II had a water-to-binder ratio and a cement content of 0.45 and 400 kg/ ml respectively. Recycled aggregate was ased as 20% , 50% , and 100% replacements of natural coarse aggregate in the concrete mixtures in both series. In cutdition, fly ash was used as 0% , 25% and 35% by weight replacements of cement. The results show that the compressive strengths of the concrete decreased as the recycled aggregate and the fly ash contents increased. The total porosity and average porosity diameter of the concrete increased us the recycled aggregate content increased. Furtherrruore , an increase in the recycled aggregate content decreased the resistance to chloride ion penetration. Nevertheless, the replacement of cement by 25% fly ush improved the resistance to chloride ion penetration and pore diameters and reduced the total porosity of the recycled aggregate concrete.

Freeze-thaw Durability of Recycled Aggregate Concrete:An Overview

The characteristics of surface appearances,mass loss,relative dynamic modulus of elasticity and strength loss of different recycled aggregate concretes(RAC) exposed to freeze-thaw cycles were analyzed.It was found that the freeze-thaw resistance of RAC could be determined by the recycled aggregate compositions and admixtures.Both the saturation degree and the air void structure were the key factors influencing the freeze-thaw damage on concrete.Some major proposed freeze-thaw deterioration mechanisms were utilized to interpret the freeze-thaw damage on recycled aggregate concrete.Meanwhile,some potential measures to enhance the freeze-thaw resistance of concrete were summarized and discussed.

Effect of flexural loading on degradation progress of recycled aggregate concrete subjected to sulfate attack and wetting-drying cycles

The degradation progress of recycled aggregate concrete(RAC) subjected to sulfate attack under wetting-drying cycles and flexural loading is studied. Three different stress ratios(0, 0.3 and 0.5) were applied in this test. The variations of relative dynamic elastic modulus Erd and water-soluble SO2-4 contents in RAC were used to evaluate degradation progress. The changes in mineral products and microstructures of interior concrete were investigated by means of X-ray diffraction(XRD), the environmental scanning electron microscope(ESEM) and X-ray computed tomography(X-CT). The results indicate that flexural loading accelerates the degradation of RAC under sulfate attack and wetting-drying cycles by expediting the transmission of SO2-4 into interior concrete. Furthermore, the accelerated effect of flexural loading is more obvious with the increase of stress ratio, that is because higher stress ratios can accelerate the extension of microcracks and generate more channels for the transmission of SO2-4. Also, more expansive products(gypsum and ettringite) are generated by the reaction of Ca(OH)2 with SO2-4, which can further accelerate the degradation of RAC.

Damage assessment for seismic response of recycled concrete filled steel tube columns

A model for evaluating structural damage of recycled aggregate concrete filled steel tube （RCFST） columns under seismic effects is proposed in this paper. The proposed model takes the lateral deformation and the effect of repeated cyclic loading into account. Available test results were collected and utilized to calibrate the parameters of the proposed model. A seismic test for six RCFST columns was also performed to validate the proposed damage assessment model. The main test parameters were the recycled coarse aggregate （RCA） replacement percentage and the bond-slip property. The test results indicated that the seismic performance of the RCFST member depends on the RCA contents and their damage index increases as the RCA replacement percentage increases. It is also indicated that the damage degree of RCFST changes with the variation of the RCA replacement percentage. Finally, comparisons between the RCA contents, lateral deformation ratio and damage degree were implemented. It is suggested that an improvement procedure should be implemented in order to compensate for the performance difference between the RCFST and normal concrete filled steel tubes （CFST）.

Improving performance of recycled aggregate concrete with superfine pozzolanic powders

Phosphorous slag （PHS）, ground granulated blast-furnace slag （GGBS） and fly ash （FA） were used as replacements of Portland cement to modify the microstruc^xe of recycled aggregate concrete （RAC）. A new manufacturing method named ＂W3T4＂ was proposed to improve the performances of interracial transition zone （ITZ） between recycled aggregate and mortar. The mechanical properties and the durability of RAC were tested, which show that this new manufacturing method improves the properties of RAC, and the GGBS with finest size makes a great contribution to the performance of RAC due to its better filling effect and much earlier pozzolanic reaction. Combined with GGBS, the effects of PHS on the retardation of setting time can be alleviated and the synergistic effect helps to make a more compact RAC. For the RAC with 25% of the recycled aggregate （RA） replacement and 10% PHS ＋ 10% GGBS additives, the compressive strength increases by 25.4%, but the permeability decreases by 64.3% with respect to the reference concrete made with nature aggregates. The micro-mechanisms of these improvements were investigated by the scanning electron microscope （SEM）. The SEM images show that the new manufacturing method, adding superfine pozzolanic powders and super-plasticizer benefits, makes a much denser ITZ in RAC.

Bond Behavior between BFRP Bars and Hybrid Fiber Recycled Aggregate Concrete after High Temperature

The aim of this study is to improve the bond performance of basalt fiber reinforced polymer(BFRP)bars and recycled aggregate concrete(RAC)after being exposed to high temperatures.The bond behavior(failure modes,bond strength,bond stress-slip curves)between BFRP bars and hybrid fiber recycled aggregate concrete(HFRAC)after being exposed to temperatures ranging from 20℃up to 500℃was studied by using pull-out tests.The effect of high temperatures on mechanical properties of concrete(compressive strength,splitting tensile strength)and tensile strength of BFRP bars was also investigated.The bond strength decreased as the temperature increased and the drop of bond strength between RAC and BFRP bar was larger than that between HFRAC and BFRP bar.As the temperature rises,the key factor affecting the bond strength was gradually transformed from concrete strength to BFRP bar strength.The relationship between bond stress and slip in the dimensionless bond stress-slip ascending section was established,which was in good agreement with the experimental results.

Recycled Aggregates:Production,Properties and Value-added Sustainable Applications

Part of an extensive research undertaken by the Concrete and Masonry Research Group at Kingston University-London was reported to demonstrate through scientific research and full-scale site trials,that quality recycled concrete aggregates can be produced and can be used successfully in a range of concrete applications.The effects of up to 100% coarse recycled concrete aggregate（RCA） on fresh,engineering and durability related properties were established and assessed its suitability for use in a rage of sustainable applications.

The Complete Stress-strain Curve of Recycled Aggregate Concrete under Uniaxial Compression Loading

The mechanical performance of recycled aggregate concrete （RAC） is investigated. An experiment on the complete stress-strain curve under uniaxial compression loading of RAC is carried out. The experimental results indicate that the peak stress, peak strain, secant modulus of the peak point and original point increase with the strength grade of RAC enhanced. On the contrary, the residual stress of RAC decreases with the strength grade enhancing, and the failure of RAC is often broken at the interface between the recycled aggregate and the mortar matrix. Finally, the constitutive model of stress-strain model of RAC has been constituted, and the results from the constitutive model of stress-strain meet the experiment results very well.

Study of the seismic response of a recycled aggregate concrete frame structure

Based on six-degree-of-freedom three-dimensional shaking table tests, the seismic response of a recycled aggregate concrete （RAC） frame was obtained. The analysis results indicate that the maximum story shear force and overturning moment reduce proportionally along the height of the model under the same earthquake wave. The story shear force, base shear coefficient and overturning moment of the structure increase progressively as the acceleration amplitude increases. The base shear coefficient is primarily controlled by the peak ground acceleration （PGA）. The relationships between the PGA and the shear coefficient as well as between the PGA and the dynamic amplification factor are obtained by mathematical fitting. The dynamic amplification factor decreases rapidly at the elastic-plastic stage, but decreases slowly with the development of the elastic-plasticity stage. The results show that the RAC frame structure has reasonable deformability when compared with natural aggregate concrete frame structures. The maximum inter-story drift ratios of the RAC frame model under frequent and rare intensity 8 test phases are 1/266 and 1/29, respectively, which are larger than the allowable value of 1/500 and 1/50 according to Chinese seismic design requirements. Nevertheless, the RAC frame structure does not collapse under base excitations with PGAs from 0.066 g up to 1.170 g.