Refill Friction Stir Spot Welding Al Alloy to Copper via Pure Metallurgical Joining Mechanism

The current investigation of refill friction stir spot welding(refill FSSW)Al alloy to copper primarily involved plunging the tool into bottom copper sheet to achieve both metallurgical and mechanical interfacial bonding.Compared to conventional FSSW and pinless FSSW,weld strength can be significantly improved by using this method.Nevertheless,tool wear is a critical issue during refill FSSW.In this study,defect-free Al/copper dissimilar welds were successfully fabricated using refill FSSW by only plunging the tool into top Al alloy sheet.Overall,two types of continuous and ultra-thin intermetallic compounds(IMCs)layers were identified at the whole Al/copper interface.Also,strong evidence of melting and resolidification was observed in the localized region.The peak temperature obtained at the center of Al/copper interface was 591℃,and the heating rate reached up to 916℃/s during the sleeve penetration phase.A softened weld region was produced via refill FSSW process,the hardness profile exhibited a W-shaped appearance along middle thickness of top Al alloy.The weld lap shear load was insensitive to the welding condition,whose scatter was rather small.The fracture path exclusively propagated along the IMCs layer of Cu_(9)Al_(4) under the external lap shear loadings,both CuAl_(2) and Cu_(9)Al_(4) were detected on the fractured surface on the copper side.This research indicated that acceptable weld strength can be achieved via pure metallurgical joining mechanism,which has significant potential for the industrial applications.

Material flow behavior and microstructural evolution during refill friction stir spot welding of alclad 2A12-T4 aluminum alloy

In this study, we used the stop-action technique to experimentally investigate the material flow and microstructural evolution of alclad 2A12-T4 aluminum alloy during refill friction stir spot welding.There are two material flow components, i.e., the inward-or outward-directed spiral flow on the horizontal plane and the upward-or downward-directed flow on the vertical plane.In the plunge stage, the flow of plasticized metal into the cavity is similar to that of a stack, whereby the upper layer is pushed upward by the lower layer.In the refill stage, this is process reversed.As such, there is no obvious vertical plasticized metal flow between adjacent layers.Welding leads to the coarsening of S(Al2CuMg) in the thermo-mechanically affected zone and the diminishing of S in the stir zone.Continuous dynamic recrystallization results in the formation of fine equiaxed grains in the stir zone, but this process becomes difficult in the thermo-mechanically affected zone due to the lower deformation rate and the pinning action of S precipitates on the dislocations and sub-grain boundaries, which leads to a high fraction of low-angle grain boundaries in this zone.

Refill friction stir spot welding (RFSSW): a review of processing, similar/dissimilar materials joining, mechanical properties and fracture mechanism

Refill friction stir spot welding(RFSSW)provides a novel method to join similar and/or dissimilar metallic materials without a key-hole in the center of the joint.Having the key-hole free characterization,the similar/dissimilar RFSSW joint exhibits remarkable and endurable characteristics,including high shear strength,long fatigue life,and strong corrosion resistance.In the meanwhile,as the key-hole free joint has different microstructures compared with conventional friction stir spot welding,thus the RFSSW joint shall possess different shear and fatigue fracture mechanisms,which needs further investigation.To explore the underlying failure mechanism,the similar/dissimilar metallic material joining parameters and pre-treatment,mechanical properties,as well as fracture mechanisms under this novel technology will be discussed.In details,the welding tool design,welding parameters setting,and the influence of processing on the lap shear and fatigue properties,as well as the corrosion resistance will be mainly discussed.Moreover,the roadmap of RFFSW is also discussed.

Refill friction stir spot welding of 5083-O aluminum alloy

In this work,refill friction stir spot welding（RFSSW） was used to weld 2 mm-thick 5083-O alloy.The Box–Behnken experimental design was used to investigate the effect of welding parameters on the joint lap shear property.Results showed that a surface indentation of 0.3 mm effectively eliminated the welding defects.Microhardness of the stir zone（SZ） was higher than that of the base material（BM） and the hardness decreased with increasing the heat input during welding.The optimum failure load of 7.72 k N was obtained when using rotating speed of 2300 rpm,plunge depth of 2.4 mm and refilling time of 3.5 s.Three fracture modes were obtained during the lap shear test and all were affected by the hook defect.

Effect of tool plunge depth on the microstructure and fracture behavior of refill friction stir spot welded AZ91 magnesium alloy joints

We used refill friction stir spot welding(RFSSW)to join 2-mm-thick AZ91D-H24 magnesium alloy sheets,and we investigated in detail the effect of tool plunge depth on the microstructure and fracture behavior of the joints.A sound joint surface can be obtained using plunge depths of 2.0 and 2.5 mm.Plunge depth was found to significantly affect the height of the hook,with greater plunge depths corresponding to more severe upward bending of the hook,which compromised the tensile-shear properties of the joints.The hardness reached a minimum at the thermo-mechanically affected zone due to the precipitation phases of this zone as it dissolved into theα-matrix during the welding process.The fracture modes of RFSSW joints can be divided into three types:shear fracture,plug fracture,and shear–plug fracture.Of these,the joint with a shear–plug fracture exhibited the best tensile-shear load of 6400 N.

Effect of thermo-mechanical conditions during constrained friction processing on the particle refinement of AM50 Mg-alloy phases

Constrained Friction Processing(CFP)is a novel solid-state processing technique suitable for lightweight materials,such Mg-and Al-alloys.The technique enables grain size refinement to fine or even ultrafine scale.In this study,the effect of CFP on the microstructural refinement of AM50 rods is investigated in terms of particle size and morphology of the eutectic and secondary phases originally present in the base material,in particular the eutecticβ-Mg_(17)Al_(12)and Al-Mn phases.For that purpose,as-cast and solution heat-treated base material and processed samples were analyzed.The Al_(8)Mn_(5) intermetallic phase was identified as the main secondary phase present in all samples before and after the processing.A notorious refinement of these particles was observed,starting from particles with an average equivalent length of a few micrometers to around 560 nm after the processing.The refinement of the secondary phase refinement is attributed to a mechanism analogous to the attrition comminution,where the combination of temperature increase and shearing of the material enables the continuous breaking of the brittle intermetallic particles into smaller pieces.As for the eutectic phase,the results indicate the presence of the partially divorcedβ-Mg_(17)Al_(12)particles exclusively in the as-cast base material,indicating that no further phase transformations regarding the eutectic phase,such as dynamic precipitation,occurred after the CFP.In the case of the processed as-cast material analyzed after the CFP,the thermal energy generated during the processing led to temperature values above the solvus limit of the eutectic phase,which associated with the mechanical breakage of the particles,enabled the complete dissolution of this phase.Therefore,CFP was successfully demonstrated to promote an extensive microstructure refinement in multiple aspects,in terms of grain sizes of theα-Mg phase and presence and morphology of the Al-Mn and eutecticβ-Mg_(17)Al_(12).

Effect of connection processes on mechanical properties of 7B04 aluminum alloy structures

The static and fatigue properties of 7B04 aluminum alloy structures connected by riveting and refill friction stir spot welding(refill FSSW)were compared and analyzed.Results show that the static compression load of the typical structure connected by riveting and refill FSSW fluctuated in the range of 117-124 kN,and the shear load was in the range of 89-95 kN.Welds spacing had a small influence on the static load of the structures joined by refill FSSW.However,the fatigue life of riveted structures was lower than that joined by refill FSSW.For the welded structure,the heterogeneous microstructures of the welded joint led to the uneven microhardness,and the hook at the lap interface bent upwards at the same time.These factors made the welded structures during the fatigue test failure along the path of sleeve moving.