Graded and Quantitative Technology and Application of Coal-Bearing Reservoir Based on Seismic Reflection Characteristics

Taiyuan formation is the main exploration strata in Ordos Basin, and coals are widely developed. Due to the interference of strong reflection of coals, we cannot completely identify the effective reservoir information of coal-bearing reservoir on seismic data. Previous researchers have studied the reservoir by stripping or weakening the strong reflection, but it is difficult to determine the effectiveness of the remaining reflection seismic data. In this paper, through the establishment of 2D forward model of coal-bearing strata, the corresponding geophysical characteristics of different reflection types of coal-bearing strata are analyzed, and then the favorable sedimentary facies zones for reservoir development are predicted. On this basis, combined with seismic properties, the coal-bearing reservoir is quantitatively characterized by seismic inversion. The above research shows that the Taiyuan formation in LS block of Ordos Basin is affected by coals and forms three or two peaks in different locations. The reservoir plane sedimentary facies zone is effectively characterized by seismic reflection structure. Based on the characteristics of sedimentary facies belt and petrophysical analysis, the reservoir is semi quantitatively characterized by attribute analysis and waveform indication, and quantitatively characterized by pre stack geostatistical inversion. Based on the forward analysis of coal measure strata, this technology characterizes the reservoir facies belt through seismic reflection characteristics, and describes coal measure reservoirs step by step. It effectively guides the exploration of LS block in Ordos Basin, and has achieved good practical application effect.

Comparative Analysis of Application of Seismic Wave Reflection Method in Advanced Geological Prediction

Seismic wave reflection method is an advanced geophysical detection method in tunnel geological prediction.It is more sensitive and effective in detecting geological anomalies such as fault fracture zone and karst.In order to verify the prediction efficacy and accuracy of the seismic wave reflection method with different instruments and equipment(tunnel geological prediction[TGP]/tunnel seismic prediction[TSP])and different vibration modes(hammering,explosives),a comparison test was carried out in Jinping Tunnel.The test results showed that the time-consumption of the hammering source was short,which can greatly reduce the impact on the construction site;different vibration sources methods of seismic wave reflection can predict the unfavorable geological sections accurately.

Static Corrections Methods in the Processing of Deep Reflection Seismic Data

Statics are big challenges for the processing of deep reflection seismic data. In this paper several different statics solutions have been implemented in the processing of deep reflection seismic data in South China and their corresponding results have been compared in order to find proper statics solutions. Either statics solutions based on tomographic principle or combining the low-frequency components of field statics with the high-frequency ones of refraction statics can provide reasonable statics solutions for deep reflection seismic data in South China with very rugged surface topography, and the two statics solutions can correct the statics anomalies of both long spatial wavelengths and short ones. The surface-consistent residual static corrections can serve as the good compensations to the several kinds of the first statics solutions. Proper statics solutions can improve both qualities and reso- lutions of seismic sections, especially for the reflections of Moho in the upmost mantle.

High-resolution crustal structure of the Yinchuan basin revealed by deep seismic reflection profiling:implications for deep processes of basin

The Yinchuan basin, located on the western margin of the Ordos block, has the characteristics of an active continental rift. A NW-striking deep seismic reflection profile across the center of Yinchuan basin precisely revealed the fine structure of the crust. The images showed that the crust in the Yinchuan basin was characterized by vertical stratifications along a detachment located at a two-way travel time（TWT） of 8.0 s.The most outstanding feature of this seismic profile was the almost flat Mohorovicˇic′ discontinuity（Moho） and a high-reflection zone in the lower crust. This sub-horizontal Moho conflicts with the general assumption of an uplifted Moho under sedimentary basins and continental rifts, and may indicate the action of different processes at depth during the evolution of sedimentary basins or rifts.We present a possible interpretation of these deep processes and the sub-horizontal Moho. The high-reflection zone, which consists of sheets of high-density, mantlederived materials, may have compensated for crustal thinning in the Yinchuan basin, leading to the formation of a sub-horizontal Moho. These high-density materials may have been emplaced by underplating with mantlesourced magma.

Accuracy of the staggered-grid finite-difference method of the acoustic wave equation for marine seismic reflection modeling

Seismic wave modeling is a cornerstone of geophysical data acquisition, processing, and interpretation, for which finite-difference methods are often applied. In this paper, we extend the velocity- pressure formulation of the acoustic wave equation to marine seismic modeling using the staggered-grid finite-difference method. The scheme is developed using a fourth-order spatial and a second-order temporal operator. Then, we define a stability coefficient (SC) and calculate its maximum value under the stability condition. Based on the dispersion relationship, we conduct a detailed dispersion analysis for submarine sediments in terms of the phase and group velocity over a range of angles, stability coefficients, and orders. We also compare the numerical solution with the exact solution for a P-wave line source in a homogeneous submarine model. Additionally, the numerical results determined by a Marmousi2 model with a rugged seafloor indicate that this method is sufficient for modeling complex submarine structures.

Effective wave identification and interference analysis of the seismic reflection method in mines

Through discussion of the time-distance curve characteristics of the direct waveand from the front,side and rear of the reflection waves of the seismic reflection methodfor advanced exploration in mines,and analysis of several major interference waves inmines,the differences in time-distance curve,frequency,apparent velocity between theeffective wave and interference wave in the seismic reflection method for advanced explorationare obtained.According to the differences,the effective wave is extracted andthe interference wave is filtered and the system's precision and accuracy is improved.

Using large dynamite shots to image the structure of the Moho from deep seismic reflection experiment between the Sichuan basin and Qinling orogen

The Qinling orogen was formed as a result of the collision between the North and South China blocks. The Qinling orogen represents the location at which the southern and northern parts of the Chinese mainland col- lided, and it＇s also the intersection of the Central China orogen and the north-south tectonic belt. There is evidence of strong deformation in this orogen, and it has had a long and complex geological history. We investigated the structure of the Moho in the southern Qinling orogen using large dynamite shot imaging techniques. By integrating the analysis of the single-shot and the move-out corrections profile, we determined the structure of the Moho beneath the northern Dabashan thrust belt and the southern Qinling orogen, including the mantle suture beneath Fenghuang mountain. The Moho is divided into two parts by the mantle suture zone beneath Fenghuang mountain： （1） from Ziyang to Hanyin, the north-dipping Moho is at about 45-55 km depth and the depth increases rapidly; and （2） from Hanyin to Ningshan, the south-dipping Moho is at about 40-45 km depth and shallows slowly. The mantle suture is located beneath Fenghuang mountain, and the Moho overlaps at this location： the shallower Moho is connected to the northern part of China, and the deeper Moho is connected to the southern part. This may indicate that the lithosphere in the Sichuan basin subducts to the Qinling block and that the subduction frontier reaches at least as far as Fenghuang mountain.

Characteristics of seismic reflections in central region of the South China Sea and their geological significance

More than 4 000 km 48-channel seismic reflection data from the central region of the South China Sea have been interpreted. Five seismic interfaces have been distinguished, named T1, T2, T4, T6 and Tg respectively Meanwhile, five seismic sequences numbered I - V have been divided with the ages of Quaternary and Pliocene, Later Mocene, Earlier and Middle Miocene, Oligocene and Pre- Oligocene separately. Sequences I-II overlie all parts of the area. In the continental slope and island slope, Sequences III-V are mainly found in the grabens. Sequence III is found at moot profiles of the deep-sea basin, and Sequnce IV is seen not only at the margins of the east subbasin but also at the margins of the southwest subbasin. Strong reflection from Moho is found at most profiles of the deep-sea basin. The depth of Moho varies between 10 and 12 km, with a thickness of 6- 8 km for the crust. Calculated by age-basement depth correlation formula, the age of basaltic basement in the southwest subbasin is 51-39 Ma. It is indicated that the evolution of the southwest subbasin is simultaneous with or earlier than that of the east subbasin.

Structural Characteristics of the Basement beneath Qiangtang Basin in Qinghai-Tibet Plateau: Results of Interaction Interpretation from Seismic Reflection/Refraction Data

The studies on configuration, character/property of the basement of Qiangtang basin is helpful for evaluating petroleum and nature gas resources as well as understanding the basin evolvement. Recently a moderate to high-grade metamorphic gneiss rock was found underlying beneath very low metamorphic Ordovician strata in Mayer Kangri to the north of the central uplift. That fact actually proved existence of the crystalline basement just the distribution and structures of pre-Paleozoic crystalline basement still remain puzzle. In recent years a number of active sources deep seismic profiling, to aim at lithospheric structure of northern Tibet and petroleum resources of the Qiangtang basin, had been conducted that make it possible to image the structure of the basement of the Qiangtang. Near vertical reflection profiles, included those acquired previously and those during 2004 to 2008, have been utilized in this study. By through the interaction process and interpretation between the reflection profiles and the wide-angle profile, a model with the detailed structure and velocity distribution from surface to the depth of 20 km of Qiangtang basin has been imaged.Based on the results and discussions of this study, the preliminary conclusions are as follows： （1） The velocity structure section （~20 kin） that is interactively constrained by the refraction and reflection seismic data reveals that the sedimentary stratum gently lie until 10 km in the south Qiangtang basin. （2） The basement consists of fold basement （the upper） and crystalline basement （the lower）.The fold basement buried at the average depth of 6 km with a velocity of 5.2-5.8 km/s. The shallowest appear at range of the central uplift. The crystalline basement is underlying beneath the fold basement at the average depth of 10 km with a velocity of 5.9-6.0 km/s except near Bangong-Nujiang suture. （3） The high-velocity body at the depth range of 3-6 km of the central uplift is considered as a fragment of the crystalline basement that perhaps was raised by Thermal or deformation. （4） The lower-consolidated fold basement show more affinity of Yangtze block but the crystalline basement seems more approximate to Lhasa terrene in geophysical nature. We have attempted to improve the resolution and reliability by interaction of the active seismic data and prove it effective to image complex basement structure. It will be a potential to process the piggy-back acquisition data and has wide prospects.

Tensor discriminant dictionary classification method for prestack seismic reflection patterns

The existing seismic reflection pattern classification methods need to convert multidimensional prestack seismic data into one-dimensional vectors for processing,which loses the characteristics of amplitude variation with offset/azimuth in the prestack seismic data.In this study,a tensor discriminant dictionary learning method for classifying prestack seismic reflection patterns is proposed.The method is initially based on the tensor Tucker decomposition algorithm and uses a tensor form to characterize the prestack seismic data with multidimensional features.The tensor discriminant dictionary is then used to reduce the influence of noise on the sample features.Finally,the method uses the Pearson correlation coefficient to measure the correlation degree of the sparse representation coefficients of different types of tensors.The advantages of the new method are as follows.(1)It can retain the rich structural features in different dimensions in the prestack data.(2)It adjusts the threshold of the Pearson correlation coefficient to optimize the classification effect.(3)It fully uses drilling information and expert knowledge and performs calibration training of the sample labels.The numerical-model tests confirm that the new method is more accurate and robust than the traditional support vector machine and K-nearest neighbor classification algorithms.The application of actual data further confirms that the classification results of the new method agree with the geological patterns and are more suitable for the analysis and interpretation of sedimentary facies.

Exploring the Wenchuan earthquake fault through the accurate location of WFSD-4#Well using seismic reflection

Deep drilling data on seismogenic faults that are obtained directly can help in understanding earthquake mechanisms and the resulting changes in deep structure and material composition.However,geophysical data are necessary to ensure that the planned borehole accurately drills through the target faults.In this study,the deep crustal structure of the Longmenshan fault is explored to obtain seismogenic fault characteristics of the Wenchuan earthquake.A scientific drilling project,Wenchuan Earthquake Fault Scientific Drilling No.4 Borehole(WFSD-4)is proposed with a borehole designed to drill through the north section of the fault zone while penetrating as many geological bodies and target layers related to seismogenic fault slip as possible.High-precision seismic exploration is then carried out to study the deep structure of the fault zone and achieve the scientific objective of the borehole.Two high-precision deep seismic reflection lines were arranged perpendicularly to the fault zone,and data were obtained through special acquisition schemes and processing methods.Finally,the surface position and drilling depth route of WFSD-4 are determined based on the interpretation results of seismic profiles.The seismic reflection method for site selection of the Wenchuan earthquake fault scientific drilling is proven feasible by comparing the interpretation with the actual drilling results,laying the foundation for further study on the deep structures of fault zones.

Study of“bright spots”in seismic reflection data

"bright spot" on reflection seismic profile has been regarded as one of the important indications of oil and gas,and it has been widely used in the oil and gas exploration. Moreover,with the development of new technologies,"bright spot" technique has been gradually applied to the exploration of coal,underground water and other fields,and also in the research of deep structure of the earth. Based on the reviewing of published literatures,the authors described the structural features and generation of "bright spot" on seismic profile for energy resources exploration and crustal-scale deep seismic reflection profiles,and further summarized the applications of the "bright spot"technique in energy resource exploration and deep structure research.

Application of the Common Offset Seismic Reflection Method to Urban Active Fault Surveys

The method and principle of common offset seismic surveys as well as the field data gathering and processing technique were introduced briefly. Through two urban active fault survey examples in Fuzhou and Shenyang, the efficiency and limitation of using the common offset seismic reflection technique to carry out urban active fault surveys were probed. The results show that this technique has the properties of high resolving power, better reconstruction of subsurface structures, and real-time analyzing and interpretation of investigation results on site. This method can be used to quickly locate objects under investigation accurately in the areas with thinner Quaternary overburdens and strong bedrock interface fluctuations.

High-Resolution Seismic Reflection Profiling of the Fenhe Fault in Taiyuan City

In this paper, we demonstrate the high resolution seismic reflection data for a depth range of several hundred meters across the Fenhe fault in Taiyuan city, China. In combination with the relevant borehole logs, these data provide useful constraints on the accurate position, geometry and deformation rate of the fault, as well as the kinematics of recent fault motion. The high resolution seismic reflection profiling revealed that the western branch of the Fenhe fault is a high angle, eastward dipping, oblique normal fault, and cutting up to the lower part of the Quaternary system. It was revealed that the top breaking point of this fault is at a depth of ～70m below the ground surface. A borehole log across the Fenhe fault permitted us to infer that there are two high angle, oppositely dipping, oblique normal faults. The eastem branch lies beneath the eastern embankment of the Fenhe river, dipping to the west and cutting into the Holocene late Pleistocene strata with a maximum vertical offset of ～8m. Another borehole log across the northern segment of the Fenhe fault indicates that the western branch of this fault has cut into the Holocene late Pleistocene strata with a maximum vertical offset of ～6m. The above mentioned data provide a minimum average Pleistocene Holocene vertical slip rate of 0 06～0 08mm/a and a maximum average large earthquake recurrence interval of 5 0～6 7ka for the Fenhe fault.

Rock physics and seismic reflectivity parameterization and amplitude variation with offsets inversion in terms of total organic carbon indicator

Total organic carbon (TOC) prediction with elastic parameter inversions has been widely used in the identification and evaluation of source rocks. However, the elastic parameters used to predict TOC are not only determined by TOC but also depend on the other physical properties of source rocks. Besides, the TOC prediction with the elastic parameters inversion is an indirect method based on the statistical relationship obtained from well logs and experiment data. Therefore, we propose a rock physics model and define a TOC indicator mainly affected by TOC to predict TOC directly. The proposed rock physics model makes the equivalent elastic moduli of source rocks parameterized by the TOC indicator. Combining the equivalent elastic moduli of source rocks and Gray’s approximation leads to a novel linearized approximation of the P-wave reflection coefficient incorporating the TOC indicator. Model examples illustrate that the novel reflectivity approximation well agrees with the exact Zoeppritz equation until incident angles reach 40°. Convoluting the novel P-wave reflection approximation with seismic wavelets as the forward solver, an AVO inversion method based on the Bayesian theory is proposed to invert the TOC indicator with seismic data. The synthetic examples and field tests validate the feasibility and stability of the proposed AVO inversion approach. Using the inversion results of the TOC indicator, TOC is directly and accurately estimated in the target area.

SH-Mode Seismic-Reflection Imaging of Earthfill Dams

Assessing subsurface characteristics and imaging geologic features （e.g., faults, cavities, low-velocity lay- ers, etc.） are typical problems in near-surface geophysics. These questions often have adverse geotechni-cal engineering implications, and can be especially acute when associated with high-hazard structures such as large earthen flood-control dams. Dam-related issues are becoming more frequent in the United States, because a large part of this major infrastructure was designed and constructed in the early- to mid-twentieth century; these dams are thus passing into the latter stages of their design life, where minute flaws that were overlooked or thought to be insignificant in design/construction are now proving problematic. The high-hydraulic heads associated with these structures can quicken degra-dation of weak areas and compromise long-term integrity. Addressing dam-related problems solely with traditional invasive drilling techniques is often inadequate （i.e., lack of lateral resolution） and]or econom- ically exorbitant at this scale. However, strategic geotechnical drilling integrated with the broad utility of near-surface geophysics, particularly the horizontally polarized shear-wave （SH-mode） seismic-reflection technique for imaging the internal structural detail and geological foundation conditions of earthfill embankment dams can cost-effectively improve the overall subsurface definition needed for remedial engineering. Demonstrative evidence for this supposition is provided in the form of SH-wave seismic-reflection imaging of in situ and engineered as-built components of flood-control embankment dams at two example sites in the central United States.

Paleostress Reconstruction from 3D Seismic Data and Slip Tendency in the Northern Slope Area of the Bongor Basin, Southwestern Chad

Paleostress plays a significant role in controlling the formation, accumulation, and distribution of reservoirs, and this could be an important factor in controlling the production of hydrocarbons from the unconventional reservoirs. In this study, we will use 3D seismic reflection data to perform the slip-tendency-based stress inversion to determine the stress field in the basement of the northern slope area in the Bongor Basin. The dataset for this technique is easily available in the oil and gas companies. The stress inversion results from the basement of the northern slope area of Bongor basin show that the maximum principal stress axis (σ1) is oriented vertically, the intermediate principal stress axis (σ2) is oriented N18° and the minimum principal stress axis (σ3) is oriented N105°, and σ2/σ1 = 0.60 and σ3/σ1 = 0.29. The findings of this paper provide significant information to understand the fault reactivation at the critical stage of hydrocarbon accumulation and the regional tectonic evolution.

Joint inversion of gravity and seismic data along a profile across the seismogenic fault of 2010 Yushu Ms7. 1 earthquake

Yushu Ms7.1 earthquake occurred on the Ganzi-Yushu fault zone, across which we carried out a joint relative-gravity and seismic-reflection survey, and then performed a gravity inversion constrained by the seismic-reflection result. Based on the data of complete Bouguer gravity anomaly and seismic reflection, we obtained a layered interface structure in deep crust down to Moho. Our study showed that the inversion could reveal the interfaces of strata along the survey profile and the directions of regional faults in two-dimension. From the characteristics of the observed topography of the Moho basement, we tentatively confirmed that the uplift of eastern edge of Qinghai-Tibet plateau was caused by the subduetion of the Indian plate.

Analysis Method and Application of Multiple Antiquities Sources in the Shahejie Formation of the Paleogene in the Southern Bohai Sea

B Oilfield is the most representative mid to deep oil field in the Bohai Sea, with the main oil bearing intervals being the upper and middle Shahejie-3 sections of the Paleogene Shahejie Formation. Through the development of ancient landforms, characterization of material source channels, analysis of missing heavy mineral sources, and seismic reflection characteristics of multiple material source missing, the material sources of the middle and upper Shahejie-3 sections are analyzed. During the sedimentation period of the II oil formation in the middle section of the Shasan Formation, the study area was mainly dominated by the Kendong Uplift source rocks;During the sedimentation period of the I oil formation in the middle section of the Shasan Formation, there were three material sources in the study area, namely the Kendong Uplift, the Laibei Low Uplift, and the Weibei Uplift. The Kendong Uplift was the main material source, followed by the Laibei Low Uplift;During the sedimentation period of the Upper Shasan Formation, the study area still had three sources of material supply simultaneously. At this time, the Laibei Low Uplift was the main source area, while the Kendong Uplift and Weibei Uplift had a relatively small supply capacity for the study area. In the analysis of archaeological sources, the distribution characteristics of the sedimentary system in the third section of the Shahejie Formation have been clarified, providing a research basis for the later development and adjustment of the oilfield.

Techniques for Surveying Urban Active Faults by Seismic Methods

Using the seismic method to detect active faults directly below cities is an irreplaceable prospecting technique. The seismic method can precisely determine the fault position. Seismic method itself can hardly determine the geological age of fault. However, by considering in connection with the borehole data and the standard geological cross-section of the surveyed area, the geological age of reflected wave group can be qualitatively (or semi-quantitatively) determined from the seismic depth profile. To determine the upper terminal point of active faults directly below city, it is necessary to use the high-resolution seismic reflection technique. To effectively determine the geometric feature of deep faults, especially to determine the relation between deep and shallow fracture structures, the seismic reflection method is better than the seismic refraction method.