Preparation of indium tin oxide targets with a high density and single phase structure by normal pressure sintering process

The present work mainly describes the technology for preparing indium-tin oxide （ITO） targets by cold isostatic pressing （CIP） and normal pressure sintering process. ITO powders were produced by chemical co-precipitation and shaped into an ITO green compact with a relative density of 60% by CIP under 300 MPa. Then, an ITO target with a relative density larger than 99.6% was obtained by sintering this green compact at 1550℃ for 8 h. The effects of forming pressure, sintering temperature and sintering time on the density of the target were inves- tigated. Also, a discussion was made on the sintering atmosphere.

Change in relative density of WC-Co cemented carbides in spark plasma sintering process

The relative density of WC-Co cemented carbides during spark plasma sintering（SPS） was analyzed.Based on the change in displacement of the ram in the SPS system,the relative densities in the sintering process can be achieved at different temperatures.The results indicated that densification of the samples started at near 900°C,the density rapidly reached its maximum at the increasing temperature stage,in which the temperature was lower than the sintering temperature of 1200°C,and most of the densification took place in the stage.Besides,the theoretical values were consistent with the experimental results.

Effect of sintering on the relative density of Cr-coated diamond/Cu composites prepared by spark plasma sintering

Cr-coated diamond/Cu composites were prepared by spark plasma sintering. The effects of sintering pressure, sintering temperature, sintering duration, and Cu powder particle size on the relative density and thermal conductivity of the composites were investigated in this paper. The influence of these parameters on the properties and microstructures of the composites was also discussed. The results show that the relative density of Cr-coated diamond/Cu reaches ~100% when the composite is gradually compressed to 30 MPa during the heating process. The densification temperature increases from 880 to 915℃ when the diamond content is increased from 45vol% to 60vol%. The densification temperature does not increase further when the content reaches 65vol%. Cu powder particles in larger size are beneficial for increasing the relative density of the composite.

The effects of relative density of metal foams on the stresses and deformation of beam under bending

The exact analytic solution of the pure bending beam of metallic foams is given. The effects of relative density of the material on stresses and deformation are revealed with the Triantafillou and Gibson constitutive law （TG model） taken as the analysis basis. Several examples for individual foams are discussed, showing the importance of compressibility of the cellular materials. One of the objects of this study is to generalize Hill＇s solution for incompressible plasticity to the case of compressible plasticity, and a kinematics parameter is brought into the analysis so that the velocity field can be determined.

Cyclic Oxidation Behaviors of MoSi_2 with Different Relative Density

The influence of different relative density on the cyclic oxidation behaviors of MoSi2 at 1 273 K were studied. ＂Pesting＂ was not found in all MoSi2 materials after being oxidized for 480 h. All samples exhibited continuous mass gain during the oxidation process. The mass gains of MoSi2 with the lowest relative density （78.6%） and the highest relative density （94.8%） are increased by 8.15 mg·cm^-2 and 3.48 mg·cm^-2, respectively. The surface of the material with lower relative density formed a loose, porous and discontinuous oxidation scale, which accelerated oxygen diffusion and aggravated the oxidation process. However, a dense scale in the material with higher relative density is formed, which acts a diffusion barrier to the oxygen atoms penetrating into the matrix. The high temperature oxidation resistance of MoSi2 can be improved by increasing its relative density.

Design of Lattice Structures Using Local Relative Density Mapping Method

In order to solve the problem of substantial computational resources of lattice structure during optimization, a local relative density mapping(LRDM) method is proposed. The proposed method uses solid isotropic microstructures with penalization to optimize a model at the macroscopic scale. The local relative density information is obtained from the topology optimization result. The contour lines of an optimized model are extracted using a density contour approach, and the triangular mesh is generated using a mesh generator. A local mapping relationship between the elements’ relative density and the struts’ relative cross?sectional area is established to automatically determine the diameter of each individual strut in the lattice structures. The proposed LRDM method can be applied to local finite element meshes and local density elements, but it is also suitable for global ones. In addition, some cases are con?sidered in order to test the e ectiveness of the LRDM method. The results show that the solution time of the LRDM is lower than the RDM method by approximately 50%. The proposed method provides instructions for the design of more complex lattice structures.

Unified Approach to Assess Engineering Performance of Fill Improved by Shallow to Deep Compaction Based Techniques Using Relative Density

The setting of pre assessment criteria for soil compaction is hardly determined, especially, in case of undecided structure locations. Different design guidelines recommend achieving a specific value of relative density for the compaction of fill placement works. Alternatives were discussed through the literature to predict the value of relative density based on soil field tests (e.g. cone and standard penetration tests). This paper presents the weakness of using the Over Consolidation Ratio (OCR) as guidance to assess the value of cone tip resistance using the soil relative density. The variation of OCR (from 1 to 10) has a significant effect on the qc value up to 110% when compared to the normally consolidated state. Then normally consolidated state can logically cover the compaction process with variation of 20%, 33%, and 4% for relative density values 85%, 70%, and 60%, respectively. A unified approach is recommended to predict the compaction qc-performance line using normally consolidated condition and sand relative density.

Impact of Arsenic Related Defects on Electronic Performance of ZrO2/GaAs:Density Functional Theory Calculations

Arsenic can diffuse into high-κ dielectrics during OaAs-based metal oxide semiconductor transistor process, which causes the degradation of gate dielectrics. To explore the origins of the degradation, we employ nonlocal B3LYP hybrid functional to study arsenic related defects in ZrO2. Via band alignments between the OaAs and ZrO2, we are able to determine the defect formation energy in the GaAs relative to the ZrO2 band gap and assess how they will affect the device performance. Arsenic at the interstitial site serves as a source of positive fixed charge while at the oxygen or zirconium substitutional site changes its charge state within the band gap of GaAs. Moreover, it is found that arsenic related defects produce conduction band offset reduction and gap states, which will increase the gate leakage current.

Demographic changes in China’s forests from 1998 to 2018

Background: Tree demography is an essential indicator of various forest ecosystem services, and understanding its changes is critical for the sustainable management of forests. During the past four decades, China implemented unprecedented forest restoration projects, which altered tree demography by increasing the number of trees and introducing new species. However, it remains unclear how species composition has changed in China in response to the past forest restoration and demographical processes.Methods: We applied Forest Stability Index(FSI) and the relative change of FSI(%FSI) to describe the population dynamics of tree species and structure in China since 1998, using field-survey data collected from over 200,000plot-records from the 6th to 9th National Forest Inventories(NFIs).Results: The overall populations of both natural and planted forests have grown rapidly from 1998 to 2018, while the range of changes in the relative tree density was more variable for natural forests(ranging from-8.53% to42.46%) than for planted forests(ranging from-1.01% to 13.31%). The populations declined only in some of the tree species, including Betula platyphylla, Ulmus pumila, and Robinia pseudoacacia. In contrast, the populations of trees in the largest size-class either remained stable or expanded.Conclusions: Tree density of China?s forests(both natural and planted forests) generally expanded and the overall populations increased in most size classes, with greater increases occurred in planted forests. In contrasting to the global decline trends of large diameter trees, here we found no apparent decline for trees in the largest size-class in China, highlighting China?s success in improving forest health and forest adaptations to climate change. We advocate for more studies to reveal the mechanisms of the changes in tree demography, which will help to improve forest ecosystem services such as the carbon sequestration capacity.

Spoil characterisation using UAV-based optical remote sensing in coal mine dumps

The structural integrity of mine dumps is crucial for mining operations to avoid adverse impacts on the triple bottom-line.Routine temporal assessments of coal mine dumps are a compliant requirement to ensure design reconciliation as spoil off-loading continues over time.Generally,the conventional in-situ coal spoil characterisation is inefficient,laborious,hazardous,and prone to experts'observation biases.To this end,this study explores a novel approach to develop automated coal spoil characterisation using unmanned aerial vehicle(UAV)based optical remote sensing.The textural and spectral properties of the high-resolution UAV images were utilised to derive lithology and geotechnical parameters(i.e.,fabric structure and relative density/consistency)in the proposed workflow.The raw images were converted to an orthomosaic using structure from motion aided processing.Then,structural descriptors were computed per pixel to enhance feature modalities of the spoil materials.Finally,machine learning algorithms were employed with ground truth from experts as training and testing data to characterise spoil rapidly with minimal human intervention.The characterisation accuracies achieved from the proposed approach manifest a digital solution to address the limitations in the conventional characterisation approach.

Experimental studies on liquefaction and reliquefaction potential of saturated ground subjected to repeated incremental acceleration loading with varying shaking duration

Past research has focused on the factors that influence liquefaction under normal shaking conditions.However,studies on parameters that influence the reliquefaction potential of saturated deposits during repeated shaking events are limited.In this study,an attempt has been made to examine the influence of acceleration amplitude and shaking duration on liquefaction and reliquefaction potential under repeated shaking conditions is conducted.1-g uni-axial shaking table experiments were performed on saturated ground prepared with 40%and 60%relative density.The prepared ground was subjected to alternate longer and shorter shaking durations(40 and 20 s)of repeated incremental 0.1 g,0.2 g,0.3 g and 0.4 g acceleration loading,respectively.The variation in density,excess pore water pressure(EPWP),cyclic resistance ratio(CRR)and surface settlement were estimated.The results showed that due to repeated incremental shaking events,reliquefaction was observed on the prepared ground.During longer shaking duration,the post-liquefied soil showed density improvement with improved soil resistance.However,the application of shorter duration loading followed by longer shaking reduced the beneficial effect of density improvement by disturbing the densified ground.Due to this,the ground was found to be more susceptible to reliquefaction in the subsequent incremental longer shaking event.

Effect of granulated rubber on shear strength of fine-grained sand

Review of the literature related to the mixture of shredded tire and sand shows that,despite of the increase in shear strength due to addition of tire chips,granulated rubber causes reduction in shear strength of sand.In this study,the shear behavior of mixtures of fine-grained sand and 1-5 mm granulated rubber is investigated.Sixty direct shear tests were conducted on sandegranulated rubber mixtures with various rubber contents(0%,5%,10%,20% and 30%) at different relative densities(50%,70% and 90%) and different normal stresses(34.5 kPa,54.5 kPa,74.5 kPa and 104.5 kPa).The obtained results show that the granulated rubber improves the shear strength of fine-grained sand at medium relative density and low normal stress.The degree of improvement in shear strength is a function of rubber content,relative density and normal stress.The results show that at relative density of 50%,by adding 5% granulated rubber,the internal friction angle of sand increases from 35.1° to 39.2°.However,at relative densities of 70% and 90%,addition of granulated rubber to sand decreases its internal friction angle.The results also indicate that the behavior of sand becomes more ductile with increasing granulated rubber content.Adding granulated rubber leads to greater yielding strain and less tangent stiffness of sand.The maximum dilation angle decreases with the decrease in granulated rubber content.The stress ratio of sample at critical state(ψ= 0°) decreases with increasing granulated rubber content.

Effect of Particle Size on Target Sintering Behavior of Cubic ITO Nanopowders

The effect of particle size on the density and resistivity of ITO green bodies and targets was systematically investigated.The experimental results show that the relative density of ITO green bodies decreases with the increase of ITO particle size.When the particle size is 10.7 nm,the relative density of ITO green bodies rises to the maximum value of 56.6%.The resistivity declines exponentially with the increase of particle size,which satisfies the exponential equation of R=exp(-41.823 × d).When the particle size is 41.6 nm,the resistivity reaches the minimum value of 0.8 Ω·cm.The relative density of ITO target decreases with the increase of particle size.Fine particles can increase the driving force of densification in initial stage.Electron mobility,caused by grain boundary scattering,will increase due to the increase of particle size or the decrease of grain boundary potential.When the particle size is 10.7 nm,the target with compact grain stacking and low porosity shows a maximum relative density of 99.25%,and the resistivity reaches the minimum value of 0.34×10^-3 Ω·cm.

Effects of temperature on the mechanical properties of Ti6Al4V powder compacts prepared by magnetic pulse compaction

The effects of temperature （0-500°C） on the compressive strength,hardness,average relative density,and microstructure of Ti6Al4V powder green compacts prepared by magnetic pulse compaction were investigated.The results show that with increasing heating temperature,the compressive strength first increases and then decreases with the maximum value of 976.74 MPa at 400°C.The average relative density and hardness constantly increase,and their values reach 96.11% and HRA 69.8 at 500°C,respectively.The increase of partial welding is found among the junctions of particles inside the compacts; there is no obvious grain growth inside the compacts within the temperature range.

Microstructure and mechanical properties of Ti6Al4V powder compacts prepared by magnetic pulse compaction

Ti6Al4V powder compaction was performed by using magnetic pulse compaction in air at 200℃.Effects of process parameters such as voltage,capacitance,discharge times on the microstructure,compressive strength,hardness and relative density of compacts were investigated.The experimental results show that the relative density,hardness and compressive strength of compacted specimens increase with increasing voltage.In addition,the relative density and compressive strength of compacted specimens increase with the augmentation of capacitance in the range investigated.The relative density increases,the hardness firstly increases and then tends to be a fixed value;and the compressive strength firstly increases and then decreases from one to five times compaction.Both values of the hardness and compressive strength reach the maxima of HRA 69.1 and 1 062.31 MPa,at three times compaction,respectively.There are pores in and between particles.

Strength and dilatancy behaviors of deep sands in Shanghai with a focus on grain size and shape effect

With rapid development of infrastructures like tunnels and open excavations in Shanghai,investigations on deeper soils have become critically important.Most of the existing laboratory works were focused on the clayey strata up to Layer 6 in Shanghai,i.e.at depth of up to 40 m.In this paper,Layers 7,9,and 11,which were mostly formed of sandy soils at depth of up to 150 m,were experimentally investigated with respect to physico-mechanical behaviors.The stressestrain behaviors were analyzed by the consolidated drained/undrained(CD/CU)triaxial tests under monotonic loading.One-dimensional(1D)oedometer tests were performed to investigate the consolidation properties of the sandy soils.Specimens were prepared at three different relative densities for each layer.Also,the micro-images and particle size analyzers were used to analyze the shape and size of the sand grains.The influences of grain size,density,and angularity on the stressestrain behaviors and compressibility were also studied.Compared to the other layers,Layer 11 had the smallest mean grain size(D50),highest compressibility,and lowest shear strength.In contrast,Layer 9 had the largest mean grain size,lowest compressibility,and highest shear strength.Layer 7 was of intermediate mean grain size,exhibiting more compressibility and less shear strength than that of Layer 9.Also,the critical state parameters and maximum dilatancy rate of different layers were discussed.

Effect of fiber-reinforcement on the mechanical behavior of sand approaching the critical state

Several types of ground improvement methods that employ fiber-reinforcement have been developed in recent years.A series of consolidated drained triaxial compression tests has been conducted here to examine the effect of short fibers on the mechanical properties of Toyoura sand.Sand with 0%,0.2%,0.4%,and 1%fiber contents,prepared to yield random distribution,was sheared under several confining pressures and controlled via their initial relative densities.The test results showed that the maximum and residual deviatoric stresses increased,whereas the volumetric expansion decreased with an increase in fiber content.Although the stress ratio h(=q/p′)and specific volume changed depending on the fiber content and confining pressure with shear progression,they each reached the same values for a definite fiber content at the end of shearing,independent of initial relative density.In other words,the unique critical state line can be found for a definite fiber content.Moreover,the greater the fiber content,the larger the slope of the critical state line at the end of shearing.Additionally,as the length of fibers shortened with the same percentage of fiber inclusions in sand,the deviatoric stress and the stress ratio decreased,approaching the shear-strain-volumetric response of unreinforced sand.

Electrical Conductivity of Spark Plasma Sintered W-Cu and Mo-Cu Composites for Electrical Contact Applications

Tungsten copper and molybdenum copper composites, with weight percent copper in the range of 20% - 40%, have been produced using the spark plasma sintering (SPS) technique. Other specimens having similar compositions were also developed using the conventional techniques of Liquid Phase Sintering (LPS) and Infiltration. Electrical conductivity measurements showed that the specimens produced by the SPS process had substantially higher levels of electrical conductivity than those produced by the other methods. Relative density measurements showed that the SPS specimens achieved very high densification, with relative densities in the range of 99.1% - 100%. On the other hand, the specimens produced by LPS and infiltration had relative densities in the range of 88% - 92% and 96% - 98% respectively. The superior conductivity of the SPS specimens has been attributed to the virtually full densification achieved by the process. The effect of porosity on electrical conductivity has been discussed and three standard models were assessed using results from porous sintered skeletons of pure tungsten and pure molybdenum.

Preparation of Aluminum Foam Sandwich by Rolling-bonding/Powder Metallurgy Foaming Technology

Aluminum foam sandwich was prepared by rolling-bonding/powder metallurgical foaming technology, and the effects of rolling on bond strength of face sheet/powders and powder density were studied. Moreover, the foaming agent, TiH2, was heat treated and a certain amount of Mg was added into powder in an attempt to understand how the stability and uniformity of foam was improved. The experimental results show that the foaming precursors with ideal quality were obtained by rolling-bonding process. When rolling reduction is 67%, the consistency of powders reach to 99.87%. Throughout consideration of the bonding of face sheet/ core layer powders and deformation characteristic of powders, the optimum rolling reduction is 60%-70%. Cracks and drainage during foaming were inhibited by heat treatment of foaming agent TiH2 and the addition of a certain amount of Mg. The optimum heat treatment way of TiH2 is that heat preserving 1 hour at 450 ℃; the amount of adding Mg is 1wt%.

基于FINN 和UBCSAND 本构模型的易流态货物流态化预测

Fluidization mechanism of liquefiable cargo is similar to that of sand liquefaction.But the cargo is subjected to more complex external loads during sea transportation.Based on two different constitutive models,numerical predictions were conducted in this study.And the effects of ship motions including motion acceleration,frequency and relative density of cargo on fluidization was investigated.By comparing with available the experimental data,validation is carried out.Results show that the roll motion is the most important one related to cargo fluidization.When the motion acceleration increases,the possibility of cargo fluidization increases.The higher of the cargo density the lower of the possibility of cargo fluidization.The effect of frequency on cargo fluidization is not unique,and it exists a critical value.The fluidization behavior of cargo could be described both by UBCSAND and FINN models.And the comparisons were discussed and summed up.