Permanent magnet assisted synchronous reluctance motor(PMA-SynRM)is a kind of high torque density energy conversion device widely used in modern industry.In this paper,based on the basic topology of PMA-SynRM,a novel ...Permanent magnet assisted synchronous reluctance motor(PMA-SynRM)is a kind of high torque density energy conversion device widely used in modern industry.In this paper,based on the basic topology of PMA-SynRM,a novel PMA-SynRM of asymmetric rotor with position-biased magnet is proposed.The asymmetric rotor design with position-biased magnet realizes the concentration of magnetic field lines in the motor air gap to obtain higher electromagnetic torque,and makes both of magnetic and reluctance torque obtain the peak value at the same current phase angle.The asymmetric rotor configuration is theoretically illustrated by space vector diagram,and the feasibility of high torque performance of the motor is verified.Through the finite element simulation,the effect of the side barrier on output torque and the Mises stress under the rotor asymmetrical design are analyzed.Then the motor characteristics including airgap flux density,back EMF,magnetic torque,reluctance torque,torque ripple,losses,and efficiency are calculated for both the basic and proposed PMA-SynRMs.The results show that the proposed PMA-SynRM has higher torque and efficiency than the basic topology.Moreover,the torque ripple of the proposed PMA-SynRM is reduced by the method with harmonic current injection,and the torque characteristics in the whole current cycle are analyzed.Finally,the endurance to avoid PM demagnetization is confirmed based on the PM remanence calculation.展开更多
The Power Factor Correction(PFC)in Switched Reluctance(SR)motor is discussed in this article.The SR motors are applicable for multiple applications like electric vehicles,wind mills,machineries etc.The doubly salient ...The Power Factor Correction(PFC)in Switched Reluctance(SR)motor is discussed in this article.The SR motors are applicable for multiple applications like electric vehicles,wind mills,machineries etc.The doubly salient structure of SR motor causes the occurrence of torque ripples,which affects the power factor of the motor.To improve the power quality,the power factor has to be corrected and the ripples have to be minimized.In order to achieve these objectives,a novel power factor correction(PFC)method is proposed in this work.Here,the conventional Diode Bridge Rectifier(DBR)is replaced by a Bridgeless Hybrid Resonant(HR)converter,which assists in improvising the output in a wider range.The converter is chosen because of having variety of beneficial measures including high gain.The converter’s output is fed to the SR motor by means of an asymmetric Bridge Resonant(BR)converter.The proposed converter operates in continuous mode of conduction with the switching frequency of 10 KHz.A hysteresis current controller and Proportional Integral(PI)controller are utilized for reducing the harmonics in the source current along with the regulation of output voltage.In addition,the speed control of SR motor is accomplished by means of the Whale Optimization Algorithm(WOA)assisted PI controller.The proposed methodology is effective for the control of unity power factor,torque and current ripples.The Total Harmonic Distortion(THD)of the source current is also minimized,which suits the standard of International Electrotechnical Comission IEC 61000-3-2.By this methodology,the power factor of 0.99 is achieved with 97%efficiency and 3.92%THD.The proposed methodology is validated in simulation by MATLAB and in hardware by FPGA Spartan 6E.展开更多
As members of doubly salient magnetless linear machines,linear variable flux reluctance(LVFR)and wound field flux reversal(LWFFR)machines inherit the merits of conventional magnetless linear machines such as low cost,...As members of doubly salient magnetless linear machines,linear variable flux reluctance(LVFR)and wound field flux reversal(LWFFR)machines inherit the merits of conventional magnetless linear machines such as low cost,high flux adjustment capability and high reliability.Furthermore,like linear switched reluctance machine,they have a very simple and compact long secondary,which are very attractive for long stroke applications.However,low force capability is their major defect.To solve this issue,new LVFR and LWFFR machine topologies were proposed in recent work,while lacking studies on their force improvement mechanism and further force evaluation.In this paper,LVFR and LWFFR machines with improved force performance are comparatively studied with the emphasis on their force capabilities.The operation principle of the two machines is analyzed based on magnetic field harmonics produced by flux modulation.Contributions of air-gap flux density harmonic components to no-load back electromagnetic forces of the two machines are analyzed and the average force equation is derived.Moreover,force capabilities of the both machines are investigated by means of the time-stepping finite-element analysis to verify the theoretical analysis.展开更多
In view of the large current peak and torque ripple in the actual current chopping control of switched reluctance motor,a segmented PWM duty cycle analysis method of switched reluctance motor based on current chopping...In view of the large current peak and torque ripple in the actual current chopping control of switched reluctance motor,a segmented PWM duty cycle analysis method of switched reluctance motor based on current chopping control is proposed in this paper.The method realizes the control of the winding current by adjusting the average voltage of the two ends of the winding in one cycle through the PWM duty cycle.At the same time,according to the inductance linear model,the conduction phase is divided into a small inductance region and an inductance rising region,and the analytical formulas of PWM duty cycle in the two regions are deduced respectively.Finally,through matlab/simulink simulation and motor platform experiment,the current chopping control is compared with the segmented PWM duty cycle analysis method in this paper.Simulation and experimental results show that the segmented PWM duty cycle analysis method can effectively reduce the current peak and torque ripple,and has high practical application value.展开更多
In this paper,the equivalent reluctance network model(ERNM)is used to calculate the magnetic circuit of a permanent magnet-assisted synchronous reluctance motor(PMASynRM)and calculate no-load air-gap magnetic field an...In this paper,the equivalent reluctance network model(ERNM)is used to calculate the magnetic circuit of a permanent magnet-assisted synchronous reluctance motor(PMASynRM)and calculate no-load air-gap magnetic field and electromagnetic torque.Iteration method is used to solve the relative permeability of iron core.A novel reluctance network model based on actual distribution of the magnetic flux inside the motor is established.The magnetomotive force(MMF)generated by armature winding affects the relative permeability of iron core,which is considered in the calculation of ERNM to improve the accuracy when the motor is under load.ERNM can be used to measure air-gap flux density,no-load back electromotive force(EMF),the average value of motor torque,the armature winding voltage under load,and power factor.The method of calculating the motor performance is proposed.The results of calculation are consistent with finite element method(FEM)and the computational complexity is much less than that of the FEM.The results of ERNM has been verified,which will provide a simple method for motor design and analysis.展开更多
Power generation becomes the need of developed, developing and under developed countries to meet their increasing power requirements. When affordability increases their requirement of power increases, this happens whe...Power generation becomes the need of developed, developing and under developed countries to meet their increasing power requirements. When affordability increases their requirement of power increases, this happens when increased per capita consumption. The existing power scenario states that highest power is produced using firing of coals called thermal energy. A high efficiency Switched Reluctance Generator (SRG) based high frequency switching scheme to enhance the output for grid connectivity is designed, fabricated and evaluated. This proposed method generates the output for the low wind speed. It provides output at low speed because of multi-level DC-DC converter and storage system. It is an efficient solution for low wind power generation. The real time readings and results are discussed.展开更多
The current research of electro-hydraulic servo valves mainly focuses on the vibration, pressure oscillating and source of noise. Unfortunately, literatures relating to the study of the influence of the magnetic reluc...The current research of electro-hydraulic servo valves mainly focuses on the vibration, pressure oscillating and source of noise. Unfortunately, literatures relating to the study of the influence of the magnetic reluctances of the magnetic elements are rarely available. This paper aims to analyze the influence of the magnetic reluctances of the magnetic elements on torque motor. Considering these magnetic reluctances ignored in previous literatures, a new mathematical model of servo valve torque motor is developed and proposed based on the fundamental laws of electromagnetism. By using this new mathematical model and the previous models, electromagnetic torque constant and magnetic spring stiffness are evaluated for a given set of torque motor parameters. A computer simulation by using AMESim software is also performed for the same set of torque motor parameters to verify the proposed model. The theoretical results of electromagnetic torque constant and magnetic spring stiffness evaluated by the proposed model render closer agreement with the simulation results than those evaluated by the previous models. In addition, an experimental measurement of the magnetic flux densities in the air-gaps is carried out by using SFL218 servo valve torque motor. Compared with the theoretical results of the magnetic flux densities in the air-gaps evaluated by the previous models, the theoretical results evaluated by the proposed model also show better agreement with the experimental data. The proposed model shows the influence of the magnetic reluctances of the magnetic elements on the servo valve torque motor, and offers modified and analytical expressions to electromagnetic torque constant and magnetic spring stiffness. These modified and analytical expressions could provide guidance more accurately for a linear control design approach and sensitivity analysis on electro-hydraulic servo valves than the previous expressions.展开更多
In this paper,an improved discharging circuit was proposed to quicken the decay of the current in the drive coil in a reluctance accelerator when the armature reaches the center of the coil.The aim of this is to preve...In this paper,an improved discharging circuit was proposed to quicken the decay of the current in the drive coil in a reluctance accelerator when the armature reaches the center of the coil.The aim of this is to prevent the suck-back effect caused by the residual current in drive coil.The method is adding a reverse charging branch with a small capacitor in the traditional pulsed discharging circuit.The results under the traditional circuit and the improved circuit were compared in a simulation.The experiment then verified the simulations and they had good agreement.Simulation and experiment both demonstrated the improved circuit can effectively prevent the suck-back effect and increase the efficiency.At the voltage of 800 V,an efficiency increase of 36.34% was obtained.展开更多
The performance of synchronous reluctance motor (SynRM) degrades due to chaos when its systemic parameters fall into a certain area. To control the undesirable chaos in SynRM, a passive control law is presented in t...The performance of synchronous reluctance motor (SynRM) degrades due to chaos when its systemic parameters fall into a certain area. To control the undesirable chaos in SynRM, a passive control law is presented in this paper, which transforms the chaotic SynRM into an equivalent passive system. It is proved that the equivalent system can be asymptotically stabilized at the set equilibrium point, namely, chaos in SynRM can be controlled. Moreover, in order to eliminate the influence of undeterministic parameters, an adaptive law is introduced into the designed controller. Computer simulation results show that the proposed controller is very effective and robust against the uncertainties in systemic parameters. The present study may help to maintain the secure operation of industrial servo drive system.展开更多
In order to improve the reliability in torque calculation of SRM,an accurate nonlinear torque model regresses by recursive robust least squares support vector regression(RR-LSSVR)is proposed in this paper.The model is...In order to improve the reliability in torque calculation of SRM,an accurate nonlinear torque model regresses by recursive robust least squares support vector regression(RR-LSSVR)is proposed in this paper.The model is in terms of a segmented-rotor switched reluctance motor(SSRM).The characteristics of the SSRM is introduced to show its nonlinear characteristics both in magnetic and torque.Then,its mathematic model is established,and an accurate inductance measurement method and a torque calculation method are presented.After this,the principle of the RR-LSSVR and why it can adjust weights according to errors are described.The model used the RR-LSSVR algorithm shows an outstanding capability in accuracy and quickness compared with other algorithms.Finally,to further validate the accuracy of the proposed model in practical application,simulation and experiment are designed based on a 16/10 SSRM.展开更多
This paper focuses on the simulation and test of the switched reluctance starter/generator systems. Through the emulational analysis of the initial starting torque, the optimal turn-on section of the power switches is...This paper focuses on the simulation and test of the switched reluctance starter/generator systems. Through the emulational analysis of the initial starting torque, the optimal turn-on section of the power switches is discovered. The fundamental theory of the generating operation is analyzed with the linearity model, and a new method is presented based on voltage pulse width modulation for the generating mode control. Through the steady-state and optimized emulation of the output power and system efficiency, the optimizational control approach for the generating mode over a wide speed range is introduced. At last, the test of the 3KW prototype system shows that the dynamic and static performance of this system is fine.展开更多
The switchless reluctance motor’s non-permanent magnet structure design ensures its high reliability in the marine environment;thus,it is a feasible solution for the generator of a sea wave power generation system.Ho...The switchless reluctance motor’s non-permanent magnet structure design ensures its high reliability in the marine environment;thus,it is a feasible solution for the generator of a sea wave power generation system.However,the corresponding thrust density and efficiency remain insufficient.This study focused on a new type of flat linear switched reluctance motor(LSRM),using the finite element software to establish a structural model,and optimized the design with the goal of improving the efficiency and energy density.The entropy method was adopted for sensitivity stratification to objectively select weights to avoid the influence of subjectively selected different proportional weights on the optimization results.Based on the entropy method,the sensitivity of different structural parameters was stratified,and the simulated annealing algorithm,response surface method,and single parameter scanning method were combined for optimization.Finally,the optimal structural size parameters of the motor were determined.Based on the two-dimensional finite element method,to simulate the electromagnetic performance of the reluctance motor under different operating conditions,such as thrust,loss,and efficiency,changes in motor performance before and after optimization were compared to verify the high power generation efficiency and energy density of the optimized linear motor.展开更多
Linear switch reluctance machine(LSRM)has been tried to act as an alternative generator for direct drive linear wave energy converter(WEC).Many researchers have proposed new topologies of LSRM to improve the power den...Linear switch reluctance machine(LSRM)has been tried to act as an alternative generator for direct drive linear wave energy converter(WEC).Many researchers have proposed new topologies of LSRM to improve the power density,efficiency and reliability.However,the control methods for LSRM applied in direct drive WEC have been paid little attention,especially control methods considering the wave energy generator operating characteristics.In this paper,according to the generator control requirements of the direct drive WEC,force control algorithm for LSRM operating in four quadrants without a speed closed loop is put forward.The force ripple of LSRM is suppressed using force sharing function method.The four-quadrant control is easy to realize requiring only phase currents information.Simulation results validate the proposed method and indicate that LSRM is able to be used as the generator for direct drive WEC.展开更多
A category of permanent-magnet-shield(PM-shield)axial-field dual-rotor segmented switched reluctance machines(ADS-SRMs)are presented in this paper.These topologies are featured by using the magnetic material to shield...A category of permanent-magnet-shield(PM-shield)axial-field dual-rotor segmented switched reluctance machines(ADS-SRMs)are presented in this paper.These topologies are featured by using the magnetic material to shield the flux leakage in the stator and rotor parts.Besides,the deployed magnets weaken the magnetic saturation in the iron core,thus increasing the main flux.Hence,the torque-production capability can be increased effectively.All the PM-shield topologies are proposed and designed based on the magnetic equivalent circuit(MEC)model of ADS-SRM,which is the original design deploying no magnet.The features of all the PM-shield topologies are compared with the original design in terms of the magnetic field distributions,flux linkages,phase inductances,torque components,and followed by their motion-coupled analyses on the torque-production capabilities,copper losses,and efficiencies.Considering the cost reduction and the stable ferrite-magnet supply,an alternative proposal using the ferrite magnets is applied to the magnetic shielding.The magnet demagnetization analysis incorporated with the thermal behavior is performed for further verification of the motor performance.展开更多
This paper deals with an analytical method to effectively calculate the inductance of an exterior-rotor switched reluctance motor(SRM),which evaluates the winding inductance of both the active section and the end sect...This paper deals with an analytical method to effectively calculate the inductance of an exterior-rotor switched reluctance motor(SRM),which evaluates the winding inductance of both the active section and the end section,accounting for the influence of core saturation.According to the inductance calculated by the analytical model,the flux linkage table and torque table can be established,and the steady state performance such as phase current,flux linkage,copper loss and core loss can be predicted.Effectiveness of this method is verified by the finite element method as well as by experimental results of a 12/8 SRM prototype.展开更多
The armature is an important part affecting the energy conversion efficiency of a reluctance accelerator.In this paper,six kinds of soft magnetic materials are chosen and four structures are designed for the armature....The armature is an important part affecting the energy conversion efficiency of a reluctance accelerator.In this paper,six kinds of soft magnetic materials are chosen and four structures are designed for the armature.At first,the circuit and magnetic force are theoretically analyzed.Then the armatures with different materials and structures are used in the simulation,and the performances are compared and analyzed.At last,the experiment verifies the theory analysis and simulation design.It is concluded that the saturation flux density and conductivity of the material are the key factors affecting the armature force,and the optimization of armature structure can effectively restrain the eddy current,reduce negative force and improve efficiency.Compared with cutting slits in solid armatures,laminating the sheets radially can reduce the eddy current more efficiently.Although slitting can prevent the eddy current to a certain extent,meanwhile,it will decrease the magnetic force because of the losing of magnetized volume and the surface area.Hence,choosing the high saturation flux density material and making out the armature with radially_laminated sheets will improve the efficiency of the reluctance accelerator.In this paper,the silicon steel radially_laminated armature is a better choice for the armature design of the reluctance accelerator.展开更多
As there is no need of permanent magnet(PM)material and only silicon steel sheet required on the rotor,synchronous reluctance machine(SynRM)can be used for many applications and draws a great research interest.For the...As there is no need of permanent magnet(PM)material and only silicon steel sheet required on the rotor,synchronous reluctance machine(SynRM)can be used for many applications and draws a great research interest.For the SynRM,the torque ripple is a big issue and a great of work could been done on reducing it.In this paper,asymmetrical magnetic flux barriers in the SynRM rotor were studied comprehensively,including angle and width of each layer and each side of the magnetic barrier.The SynRMb with asymmetrical and parallel magnetic flux barrier was found as the best way to design SynRM based on the multi-objective design optimization method.Moreover,each parameter was studied to show the design rule of the asymmetrical magnetic flux barrier.As the average torque will be reduced with the asymmetrical barrier is used,the grain-oriented silicon steel is used on stator teeth of the SynRMb(SynRMbG)was proposed and studied.The analysis results show that the proposed new method can make the SynRM have better performance.展开更多
In order to reduce the torque ripple,increase the average torque and optimize the drive performance of the switched reluctance motor (SRM),the nonlinear dynamic model of SRM is established in the MATLAB /Simulink envi...In order to reduce the torque ripple,increase the average torque and optimize the drive performance of the switched reluctance motor (SRM),the nonlinear dynamic model of SRM is established in the MATLAB /Simulink environment.The effects of the turn-on and turn-off angles are investigated by the simulation results of the dynamic model,and the function is made among the rotor speed,turn-on angle and turn-off angle.To optimize the torque dynamic performance,the two-objective simultaneous optimization function is proposed by two weight factors.And the optimized turn-on and turn-off angles as functions of rotor speed are developed by using the simultaneous optimization method.Then the optimized torque controller is designed based on the optimized turn-on and turn-off angles.The simulation results show that the optimized torque controller designed in this paper can effectively reduce the torque ripple and increase the average torque,and optimize the torque dynamic performance of the SRM.展开更多
In traditional analytical method(AM),the magnetic saturation is always ignored to simplify the calculation process.However,synchronous reluctance motors(SynRMs)often operate around saturation point to achieve higher t...In traditional analytical method(AM),the magnetic saturation is always ignored to simplify the calculation process.However,synchronous reluctance motors(SynRMs)often operate around saturation point to achieve higher torque density.Therefore,a new AM is proposed,in which the saturation of stator iron has been considered.The key of the proposed method includes a saturation factor,and an iterative method is adopted to compute the saturation factor in the SynRM by increasing the air-gap length.Especially,the proposed AM can be applied to a SynRM even with shifted-asymmetrical-salient-poles.In the process of AM,the expression of stator magnetomotive force(MMF)is built firstly.Additionally,the air-gap density including slotting effect and salient-poles is calculated.Then,the rotor MMF under saturation of the stator iron is obtained.Therefore,the precision of the instantaneous torque can be improved significantly.Eventually,by the verification of finite elements method(FEM)and experiments,the torque performance of SynRMs with shifted asymmetrical rotor can be predicted accurately by the proposed AM.展开更多
This paper presents a voltage controller for a 12/8 switched reluctance generator (SRG). SR machines have a robust with simple structure because they have no windings or permanent magnets on the rotor, so they are cap...This paper presents a voltage controller for a 12/8 switched reluctance generator (SRG). SR machines have a robust with simple structure because they have no windings or permanent magnets on the rotor, so they are capable of working at high speed application and at rough condition. However, due to nonlinear nature, doubly salient poles, time variant parameters, and non-ideal current waveform, The SRG output voltage inherently contains ripples. The proposed voltage controller is based on fuzzy logic that is very efficient over uncertainty and parameter variations. The effectiveness of the proposed control method is verified by comparing the obtained result with that of a PI-controller.展开更多
基金supported in part by the National Natural Science Foundation of China under Grant 52077123 and 51737008in part by the Natural Science Foundation of Shandong Province of China for Outstanding Young Scholars,under Grant ZR2021YQ35。
文摘Permanent magnet assisted synchronous reluctance motor(PMA-SynRM)is a kind of high torque density energy conversion device widely used in modern industry.In this paper,based on the basic topology of PMA-SynRM,a novel PMA-SynRM of asymmetric rotor with position-biased magnet is proposed.The asymmetric rotor design with position-biased magnet realizes the concentration of magnetic field lines in the motor air gap to obtain higher electromagnetic torque,and makes both of magnetic and reluctance torque obtain the peak value at the same current phase angle.The asymmetric rotor configuration is theoretically illustrated by space vector diagram,and the feasibility of high torque performance of the motor is verified.Through the finite element simulation,the effect of the side barrier on output torque and the Mises stress under the rotor asymmetrical design are analyzed.Then the motor characteristics including airgap flux density,back EMF,magnetic torque,reluctance torque,torque ripple,losses,and efficiency are calculated for both the basic and proposed PMA-SynRMs.The results show that the proposed PMA-SynRM has higher torque and efficiency than the basic topology.Moreover,the torque ripple of the proposed PMA-SynRM is reduced by the method with harmonic current injection,and the torque characteristics in the whole current cycle are analyzed.Finally,the endurance to avoid PM demagnetization is confirmed based on the PM remanence calculation.
文摘The Power Factor Correction(PFC)in Switched Reluctance(SR)motor is discussed in this article.The SR motors are applicable for multiple applications like electric vehicles,wind mills,machineries etc.The doubly salient structure of SR motor causes the occurrence of torque ripples,which affects the power factor of the motor.To improve the power quality,the power factor has to be corrected and the ripples have to be minimized.In order to achieve these objectives,a novel power factor correction(PFC)method is proposed in this work.Here,the conventional Diode Bridge Rectifier(DBR)is replaced by a Bridgeless Hybrid Resonant(HR)converter,which assists in improvising the output in a wider range.The converter is chosen because of having variety of beneficial measures including high gain.The converter’s output is fed to the SR motor by means of an asymmetric Bridge Resonant(BR)converter.The proposed converter operates in continuous mode of conduction with the switching frequency of 10 KHz.A hysteresis current controller and Proportional Integral(PI)controller are utilized for reducing the harmonics in the source current along with the regulation of output voltage.In addition,the speed control of SR motor is accomplished by means of the Whale Optimization Algorithm(WOA)assisted PI controller.The proposed methodology is effective for the control of unity power factor,torque and current ripples.The Total Harmonic Distortion(THD)of the source current is also minimized,which suits the standard of International Electrotechnical Comission IEC 61000-3-2.By this methodology,the power factor of 0.99 is achieved with 97%efficiency and 3.92%THD.The proposed methodology is validated in simulation by MATLAB and in hardware by FPGA Spartan 6E.
基金supported in part by the National Natural Science Foundation of China under Grant 51977099 and Grant 52177044in part by the Hong Kong Scholars Program under Grant XJ2019031+2 种基金in part by the China Postdoctoral Science Foundation under Grant 2019T120395in part by the Natural Science Foundation of Jiangsu Higher Education Institutions under Grant 21KJA470004in part by the Priority Academic Program Development of Jiangsu Higher Education Institutions.
文摘As members of doubly salient magnetless linear machines,linear variable flux reluctance(LVFR)and wound field flux reversal(LWFFR)machines inherit the merits of conventional magnetless linear machines such as low cost,high flux adjustment capability and high reliability.Furthermore,like linear switched reluctance machine,they have a very simple and compact long secondary,which are very attractive for long stroke applications.However,low force capability is their major defect.To solve this issue,new LVFR and LWFFR machine topologies were proposed in recent work,while lacking studies on their force improvement mechanism and further force evaluation.In this paper,LVFR and LWFFR machines with improved force performance are comparatively studied with the emphasis on their force capabilities.The operation principle of the two machines is analyzed based on magnetic field harmonics produced by flux modulation.Contributions of air-gap flux density harmonic components to no-load back electromagnetic forces of the two machines are analyzed and the average force equation is derived.Moreover,force capabilities of the both machines are investigated by means of the time-stepping finite-element analysis to verify the theoretical analysis.
基金supported by National Natural Science Foundation of China under Grant 52167005Science and Technology Research Project of Jiangxi Provincial Department of Education under Grant GJJ200826。
文摘In view of the large current peak and torque ripple in the actual current chopping control of switched reluctance motor,a segmented PWM duty cycle analysis method of switched reluctance motor based on current chopping control is proposed in this paper.The method realizes the control of the winding current by adjusting the average voltage of the two ends of the winding in one cycle through the PWM duty cycle.At the same time,according to the inductance linear model,the conduction phase is divided into a small inductance region and an inductance rising region,and the analytical formulas of PWM duty cycle in the two regions are deduced respectively.Finally,through matlab/simulink simulation and motor platform experiment,the current chopping control is compared with the segmented PWM duty cycle analysis method in this paper.Simulation and experimental results show that the segmented PWM duty cycle analysis method can effectively reduce the current peak and torque ripple,and has high practical application value.
基金This work was supported in part by the National Natural Science Foundation of China under Grant 51737008.
文摘In this paper,the equivalent reluctance network model(ERNM)is used to calculate the magnetic circuit of a permanent magnet-assisted synchronous reluctance motor(PMASynRM)and calculate no-load air-gap magnetic field and electromagnetic torque.Iteration method is used to solve the relative permeability of iron core.A novel reluctance network model based on actual distribution of the magnetic flux inside the motor is established.The magnetomotive force(MMF)generated by armature winding affects the relative permeability of iron core,which is considered in the calculation of ERNM to improve the accuracy when the motor is under load.ERNM can be used to measure air-gap flux density,no-load back electromotive force(EMF),the average value of motor torque,the armature winding voltage under load,and power factor.The method of calculating the motor performance is proposed.The results of calculation are consistent with finite element method(FEM)and the computational complexity is much less than that of the FEM.The results of ERNM has been verified,which will provide a simple method for motor design and analysis.
文摘Power generation becomes the need of developed, developing and under developed countries to meet their increasing power requirements. When affordability increases their requirement of power increases, this happens when increased per capita consumption. The existing power scenario states that highest power is produced using firing of coals called thermal energy. A high efficiency Switched Reluctance Generator (SRG) based high frequency switching scheme to enhance the output for grid connectivity is designed, fabricated and evaluated. This proposed method generates the output for the low wind speed. It provides output at low speed because of multi-level DC-DC converter and storage system. It is an efficient solution for low wind power generation. The real time readings and results are discussed.
基金Supported by National Natural Science Foundation of China(Grant No.50975055)
文摘The current research of electro-hydraulic servo valves mainly focuses on the vibration, pressure oscillating and source of noise. Unfortunately, literatures relating to the study of the influence of the magnetic reluctances of the magnetic elements are rarely available. This paper aims to analyze the influence of the magnetic reluctances of the magnetic elements on torque motor. Considering these magnetic reluctances ignored in previous literatures, a new mathematical model of servo valve torque motor is developed and proposed based on the fundamental laws of electromagnetism. By using this new mathematical model and the previous models, electromagnetic torque constant and magnetic spring stiffness are evaluated for a given set of torque motor parameters. A computer simulation by using AMESim software is also performed for the same set of torque motor parameters to verify the proposed model. The theoretical results of electromagnetic torque constant and magnetic spring stiffness evaluated by the proposed model render closer agreement with the simulation results than those evaluated by the previous models. In addition, an experimental measurement of the magnetic flux densities in the air-gaps is carried out by using SFL218 servo valve torque motor. Compared with the theoretical results of the magnetic flux densities in the air-gaps evaluated by the previous models, the theoretical results evaluated by the proposed model also show better agreement with the experimental data. The proposed model shows the influence of the magnetic reluctances of the magnetic elements on the servo valve torque motor, and offers modified and analytical expressions to electromagnetic torque constant and magnetic spring stiffness. These modified and analytical expressions could provide guidance more accurately for a linear control design approach and sensitivity analysis on electro-hydraulic servo valves than the previous expressions.
基金This work was supported by the Fundamental Research Funds for the Central Universities[Grant number 2019XJ01].
文摘In this paper,an improved discharging circuit was proposed to quicken the decay of the current in the drive coil in a reluctance accelerator when the armature reaches the center of the coil.The aim of this is to prevent the suck-back effect caused by the residual current in drive coil.The method is adding a reverse charging branch with a small capacitor in the traditional pulsed discharging circuit.The results under the traditional circuit and the improved circuit were compared in a simulation.The experiment then verified the simulations and they had good agreement.Simulation and experiment both demonstrated the improved circuit can effectively prevent the suck-back effect and increase the efficiency.At the voltage of 800 V,an efficiency increase of 36.34% was obtained.
基金Project supported by the National Natural Science Foundation of China (Grant No 70571017)
文摘The performance of synchronous reluctance motor (SynRM) degrades due to chaos when its systemic parameters fall into a certain area. To control the undesirable chaos in SynRM, a passive control law is presented in this paper, which transforms the chaotic SynRM into an equivalent passive system. It is proved that the equivalent system can be asymptotically stabilized at the set equilibrium point, namely, chaos in SynRM can be controlled. Moreover, in order to eliminate the influence of undeterministic parameters, an adaptive law is introduced into the designed controller. Computer simulation results show that the proposed controller is very effective and robust against the uncertainties in systemic parameters. The present study may help to maintain the secure operation of industrial servo drive system.
基金This work was supported by the National Natural Science Foundation of China under Project 51875261the Natural Science Foundation of Jiangsu Province of China under Projects BK20180046 and BK20170071the“Qinglan project”of Jiangsu Province,and the Key Project of Natural Science Foundation of Jiangsu Higher Education Institutions under Project 17KJA460005.
文摘In order to improve the reliability in torque calculation of SRM,an accurate nonlinear torque model regresses by recursive robust least squares support vector regression(RR-LSSVR)is proposed in this paper.The model is in terms of a segmented-rotor switched reluctance motor(SSRM).The characteristics of the SSRM is introduced to show its nonlinear characteristics both in magnetic and torque.Then,its mathematic model is established,and an accurate inductance measurement method and a torque calculation method are presented.After this,the principle of the RR-LSSVR and why it can adjust weights according to errors are described.The model used the RR-LSSVR algorithm shows an outstanding capability in accuracy and quickness compared with other algorithms.Finally,to further validate the accuracy of the proposed model in practical application,simulation and experiment are designed based on a 16/10 SSRM.
文摘This paper focuses on the simulation and test of the switched reluctance starter/generator systems. Through the emulational analysis of the initial starting torque, the optimal turn-on section of the power switches is discovered. The fundamental theory of the generating operation is analyzed with the linearity model, and a new method is presented based on voltage pulse width modulation for the generating mode control. Through the steady-state and optimized emulation of the output power and system efficiency, the optimizational control approach for the generating mode over a wide speed range is introduced. At last, the test of the 3KW prototype system shows that the dynamic and static performance of this system is fine.
基金This work is supported by the National Natural Science Foundation of China(52077141)the Natural Science Foundation of Liaoning Province(2021-YQ-09)the Liaoning Bai Qian Wan Talents Program,China。
文摘The switchless reluctance motor’s non-permanent magnet structure design ensures its high reliability in the marine environment;thus,it is a feasible solution for the generator of a sea wave power generation system.However,the corresponding thrust density and efficiency remain insufficient.This study focused on a new type of flat linear switched reluctance motor(LSRM),using the finite element software to establish a structural model,and optimized the design with the goal of improving the efficiency and energy density.The entropy method was adopted for sensitivity stratification to objectively select weights to avoid the influence of subjectively selected different proportional weights on the optimization results.Based on the entropy method,the sensitivity of different structural parameters was stratified,and the simulated annealing algorithm,response surface method,and single parameter scanning method were combined for optimization.Finally,the optimal structural size parameters of the motor were determined.Based on the two-dimensional finite element method,to simulate the electromagnetic performance of the reluctance motor under different operating conditions,such as thrust,loss,and efficiency,changes in motor performance before and after optimization were compared to verify the high power generation efficiency and energy density of the optimized linear motor.
基金This work was supported in part by the National Natural Science Foundation of China under Grant U1806224,61733010in part by the Guangdong Key Research and Development Program under Grant 2019B090917001.
文摘Linear switch reluctance machine(LSRM)has been tried to act as an alternative generator for direct drive linear wave energy converter(WEC).Many researchers have proposed new topologies of LSRM to improve the power density,efficiency and reliability.However,the control methods for LSRM applied in direct drive WEC have been paid little attention,especially control methods considering the wave energy generator operating characteristics.In this paper,according to the generator control requirements of the direct drive WEC,force control algorithm for LSRM operating in four quadrants without a speed closed loop is put forward.The force ripple of LSRM is suppressed using force sharing function method.The four-quadrant control is easy to realize requiring only phase currents information.Simulation results validate the proposed method and indicate that LSRM is able to be used as the generator for direct drive WEC.
基金the National Natural Science Foundation of China under Grant 51807094。
文摘A category of permanent-magnet-shield(PM-shield)axial-field dual-rotor segmented switched reluctance machines(ADS-SRMs)are presented in this paper.These topologies are featured by using the magnetic material to shield the flux leakage in the stator and rotor parts.Besides,the deployed magnets weaken the magnetic saturation in the iron core,thus increasing the main flux.Hence,the torque-production capability can be increased effectively.All the PM-shield topologies are proposed and designed based on the magnetic equivalent circuit(MEC)model of ADS-SRM,which is the original design deploying no magnet.The features of all the PM-shield topologies are compared with the original design in terms of the magnetic field distributions,flux linkages,phase inductances,torque components,and followed by their motion-coupled analyses on the torque-production capabilities,copper losses,and efficiencies.Considering the cost reduction and the stable ferrite-magnet supply,an alternative proposal using the ferrite magnets is applied to the magnetic shielding.The magnet demagnetization analysis incorporated with the thermal behavior is performed for further verification of the motor performance.
文摘This paper deals with an analytical method to effectively calculate the inductance of an exterior-rotor switched reluctance motor(SRM),which evaluates the winding inductance of both the active section and the end section,accounting for the influence of core saturation.According to the inductance calculated by the analytical model,the flux linkage table and torque table can be established,and the steady state performance such as phase current,flux linkage,copper loss and core loss can be predicted.Effectiveness of this method is verified by the finite element method as well as by experimental results of a 12/8 SRM prototype.
基金supported in part by the Fundamental Research Funds for the Central Universities,China[grant number 2682020GF03]in part by the Foundation of Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle,Ministry of Education,China.
文摘The armature is an important part affecting the energy conversion efficiency of a reluctance accelerator.In this paper,six kinds of soft magnetic materials are chosen and four structures are designed for the armature.At first,the circuit and magnetic force are theoretically analyzed.Then the armatures with different materials and structures are used in the simulation,and the performances are compared and analyzed.At last,the experiment verifies the theory analysis and simulation design.It is concluded that the saturation flux density and conductivity of the material are the key factors affecting the armature force,and the optimization of armature structure can effectively restrain the eddy current,reduce negative force and improve efficiency.Compared with cutting slits in solid armatures,laminating the sheets radially can reduce the eddy current more efficiently.Although slitting can prevent the eddy current to a certain extent,meanwhile,it will decrease the magnetic force because of the losing of magnetized volume and the surface area.Hence,choosing the high saturation flux density material and making out the armature with radially_laminated sheets will improve the efficiency of the reluctance accelerator.In this paper,the silicon steel radially_laminated armature is a better choice for the armature design of the reluctance accelerator.
基金the National Natural Science Foundation of China under Project 52007047,in part by the National Natural Science Foundation of China under Project 51877065,and in part by Natural Science Foundation of Hebei Province under Project E2019202220.
文摘As there is no need of permanent magnet(PM)material and only silicon steel sheet required on the rotor,synchronous reluctance machine(SynRM)can be used for many applications and draws a great research interest.For the SynRM,the torque ripple is a big issue and a great of work could been done on reducing it.In this paper,asymmetrical magnetic flux barriers in the SynRM rotor were studied comprehensively,including angle and width of each layer and each side of the magnetic barrier.The SynRMb with asymmetrical and parallel magnetic flux barrier was found as the best way to design SynRM based on the multi-objective design optimization method.Moreover,each parameter was studied to show the design rule of the asymmetrical magnetic flux barrier.As the average torque will be reduced with the asymmetrical barrier is used,the grain-oriented silicon steel is used on stator teeth of the SynRMb(SynRMbG)was proposed and studied.The analysis results show that the proposed new method can make the SynRM have better performance.
基金Sponsored by the Ph.D.Program Foundation of Ministry of Education of China(Grant No.20092302120)
文摘In order to reduce the torque ripple,increase the average torque and optimize the drive performance of the switched reluctance motor (SRM),the nonlinear dynamic model of SRM is established in the MATLAB /Simulink environment.The effects of the turn-on and turn-off angles are investigated by the simulation results of the dynamic model,and the function is made among the rotor speed,turn-on angle and turn-off angle.To optimize the torque dynamic performance,the two-objective simultaneous optimization function is proposed by two weight factors.And the optimized turn-on and turn-off angles as functions of rotor speed are developed by using the simultaneous optimization method.Then the optimized torque controller is designed based on the optimized turn-on and turn-off angles.The simulation results show that the optimized torque controller designed in this paper can effectively reduce the torque ripple and increase the average torque,and optimize the torque dynamic performance of the SRM.
基金This work was supported in part by the National Natural Science Foundation of China(51707083)in part by the Natural Science Foundation of Jiangsu Province(BK20190848)+1 种基金in part by the China Postdoctoral Science Foundation(2019M661746)by the Priority Academic Program Development of Jiangsu Higher Education Institutions.
文摘In traditional analytical method(AM),the magnetic saturation is always ignored to simplify the calculation process.However,synchronous reluctance motors(SynRMs)often operate around saturation point to achieve higher torque density.Therefore,a new AM is proposed,in which the saturation of stator iron has been considered.The key of the proposed method includes a saturation factor,and an iterative method is adopted to compute the saturation factor in the SynRM by increasing the air-gap length.Especially,the proposed AM can be applied to a SynRM even with shifted-asymmetrical-salient-poles.In the process of AM,the expression of stator magnetomotive force(MMF)is built firstly.Additionally,the air-gap density including slotting effect and salient-poles is calculated.Then,the rotor MMF under saturation of the stator iron is obtained.Therefore,the precision of the instantaneous torque can be improved significantly.Eventually,by the verification of finite elements method(FEM)and experiments,the torque performance of SynRMs with shifted asymmetrical rotor can be predicted accurately by the proposed AM.
文摘This paper presents a voltage controller for a 12/8 switched reluctance generator (SRG). SR machines have a robust with simple structure because they have no windings or permanent magnets on the rotor, so they are capable of working at high speed application and at rough condition. However, due to nonlinear nature, doubly salient poles, time variant parameters, and non-ideal current waveform, The SRG output voltage inherently contains ripples. The proposed voltage controller is based on fuzzy logic that is very efficient over uncertainty and parameter variations. The effectiveness of the proposed control method is verified by comparing the obtained result with that of a PI-controller.