Spent graphite regeneration:Exploring diverse repairing manners with impurities-catalyzing effect towards high performance and low energy consumption

Spent battery recycling has received considerable attention because of its economic and environmental potential.A large amount of retired graphite has been produced as the main electrode material,accompanied by a detailed exploration of the repair mechanism.However,they still suffer from unclear repair mechanisms and physicochemical evolution.In this study,spent graphite was repaired employing three methodologies:pickling-sintering,pyrogenic-recovery,and high-temperature sintering.Owing to the catalytic effect of the metal-based impurities and temperature control,the as-obtained samples displayed an ordered transformation,including the interlayer distance,crystalline degree,and grain size.As anodes of lithium ions batteries,the capacity of repaired samples reached up to 310 mA h g^(-1)above after 300loops at 1.0 C,similar to that of commercial graphite.Meanwhile,benefitting from the effective assembly of carbon atoms in internal structure of graphite at>1400℃,their initial coulombic efficiency were>87%.Even at 2.0 C,the capacity of samples remained approximately 244 mA h g^(-1)after 500 cycles.Detailed electrochemical and kinetic analyses revealed that a low temperature enhanced the isotropy,thereby enhancing the rate properties.Further,economic and environmental analyses revealed that the revenue obtained through suitable pyrogenic-recovering manners was approximately the largest value(5500$t^(-1)).Thus,this study is expected to clarify the in-depth effect of different repair methods on the traits of graphite,while offering all-round evaluations of repaired graphite.

Effects of β-Glucan Supplementation on Repairing of Phenol-Induced Vaginal Mucosal Epithelium Damage in Rats

Objective: To investigate the effects of different concentrations of β-glucan on the repair of damaged vaginal mucosa, the expression of vascular endothelial growth factor (VEGF), and the inflammatory factor-6 (IL-6) in vaginal tissues. Methods: Thirty-six adult female specific pathogen free (SPF)-grade Wistar rats were randomly divided into 3 phase groups with 12 rats each. Vaginal inflammation rat models were established by injecting phenol gel into the vagina of each rat at a dose of 0.1 ml/100g body weight. After modeling, rats were divided into 4 groups based on different concentrations of the test agent. The control group was injected with 0.5 ml of saline, experimental group A was injected with 0.375 ml saline 0.125 ml β-glucan, experimental group B was injected with 0.25 ml saline 0.25 ml β-glucan, and experimental group C was injected with 0.50 ml β-glucan. The injection sites were selected at the 3 o’clock and 9 o’clock positions of the vagina. Rats were sacrificed at 7-, 14-, and 28-days post-injection, and tissue samples were collected from the injection sites and prepared for histological analysis. New blood vessels and fibroblast numbers in the tissues were observed after Hematoxylin-eosin (HE) staining. The expression levels of VEGF and IL-6 in the tissues were measured using quantificational reverse transcription polymerase chain reaction (qRT-PCR). Results: Histological examination of vaginal tissue specimens at 7-, 14-, and 28-days post-injection showed that on day 7, there were no significant changes in the experimental groups compared to the control group. However, on days 14 and 28, the experimental groups showed more new blood vessels, macrophages, and fibroblasts with increased activity compared to the control group. The expression levels of VEGF in vaginal tissues were elevated on days 14 and 28 in the experimental groups. The comparison of IL-6 levels in vaginal tissues on day 28 showed that serum IL-6 levels returned to normal, and there was no statistically significant difference between the experimental and control groups. Conclusion: In the 3 experimental phases, the increase in VEGF levels in vaginal tissues on day 14 post-injection was more pronounced with higher concentrations of β-glucan, and IL-6 levels returned to normal on day 28. β-Glucan can enhance VEGF levels in damaged vaginal tissues, promote the repair of damaged vaginal tissues, and higher concentrations of β-glucan have a better effect.

Repairing of exit-hole in friction-stir-spot welded joints for 2024-T4 aluminum alloy by resistance welding

The exit-hole in friction stir spot welded(FSSWed) 2024-T4 aluminum alloy joints was successfully repaired by using a three-phase secondary rectification resistance spot welding machine, which is termed as filling exit-hole based on resistance welding(FEBRW). The filling dynamic behavior of force was recorded by a device monitoring. Optical microscope(OM), electron backscatter diffraction(EBSD), and tensile shear tests and finite element modelling were conducted to investigate the repairing stages and bonding mechanisms of the repaired joints in detail. Results showed that exit-hole was completely filled and repaired experiencing three stages. Metallurgical bonding was achieved between plug and exit-hole wall in two forms, including melting bonding in the middle of the joints and partial diffusion bonding on both the upper and bottom of the joints. The highest tensile shear strength of the repaired joints was 7.43 kN, which was 36.3% higher than that of the as welded joints. Resistance welding paves an efficient way to repair the exit-hole in FSSWed joints.

Active-passive radial-additive friction stir repairing of mechanical hole out of dimension tolerance of AZ31 magnesium alloy

In order to avoid the depth increasing of repaired hole and eliminate the super-fine grain band in stir zone by radial-additive friction stir repairing(R-AFSR), a solid-state repairing technique of active-passive radial-additive friction stir repairing(AP-RAFSR) assisted by the truncated cone-shaped filling material was proposed in this study. The mechanical hole out of dimension tolerance of AZ31 magnesium alloy was chosen as the repaired object. The results indicated that the AP-RAFSR process rather than the R-AFSR process avoided the kissing bond in the bottom of the repairing interface under the condition of the tool pin length equal to the height of the standard mechanical hole.The continuously-distributed and large-length super-fine grain bands were eliminated in the stir zone by AP-RAFSR. The maximum tensile and compressive-shear strengths of repaired hole by AP-RAFSR reached 190.6 MPa and 138.9 MPa at 1200 rpm respectively, which were equivalent to 97.7% and 89.6% of those of the standard mechanical hole. This AP-RAFSR process assisted by the truncated cone-shaped filling material provides a new technique to obtain a no-depth-increasing, defect-free and high-strength repaired mechanical hole.

Passive smart self-repairing concrete beams by using shape memory alloy wires and fibers containing adhesives

An innovative approach to increase structural survivability of concrete and maintain structural durability of concrete was developed in case of earthquakes and typhoons. This approach takes advantage of the superelastic effect of shape memory alloy(SMA) and the cohering characteristic of repairing adhesive. These SMA wires and brittle fibers containing adhesives were embedded into concrete beams during concrete casting to form smart reinforced concrete beams. The self-repairing capacity of smart concrete beams was investigated by three-point bending tests. The experimental results show that SMA wires add self-restoration capacity,the concrete beams recover almost completely after incurring an extremely large deflection and the cracks are closed almost completely by the recovery forces of SMA wires. The number or areas of SMA wires has no influence on the tendency of deformation during loading and the tendency of reversion by the superelasticity. The adhesives released from the broken-open fibers fill voids and cracks. The repaired damage enables continued function and prevents further degradation.

Algorithms for mesh repairing to represent automobile parts

In representing automobile parts with mesh in the field of reverse engineering or finite element generation, the mesh reconstruction and data exchanging between different CAD/CAM systems often introduce many invisible topological and geometrical errors into mesh. These artifacts can cause serious problems in subsequent operations such as finite element analysis, reverse engineering, animation, and simulation. In this study we propose a practical method for repairing topological and geometrical errors on mesh. First, coincident vertices during mesh input are removed, fol- lowed by the identification of non-manifold vertices and edges. The non-manifold vertices are modified, and the facets having non-manifold edges are removed. Finally, faces that have the wrong orientations in the mesh are re-oriented. Experiments show that our methods can eliminate most common mesh errors quickly and effectively. The refined mesh can be properly used in subsequent operations.

Study on Repairing Permanent Transportation Roadway in Deep Mining by Bolt-Shotcrete and Mesh Supporting

The roadway support in many places of Jiulongkou Colliery, Fengfeng Mining Bureau, such as in the Permanent transportation roadway, was failed or locally caved, which seriously affected the colliery’s coal production performance and safety. Based on analysis of supporting objects for roadway repairing, this paper proposes the supporting parameters and condruction technics. The industrial ted of 70m long roadway repairing shows that the proposed parameters and technics of bolt shotcrete and mesh support for roadway repairing are reasouable, bring good technical and economic results for the colliery, and the repairing is successful.

Post-Synthetic and In Situ Vacancy Repairing of Iron Hexacyanoferrate Toward Highly Stable Cathodes for Sodium-Ion Batteries

Iron hexacyanoferrate(FeHCF)is a promising cathode material for sodium-ion batteries.However,FeHCF always suffers from a poor cycling stability,which is closely related to the abundant vacancy defects in its framework.Herein,post-synthetic and in-situ vacancy repairing strategies are proposed for the synthesis of highquality FeHCF in a highly concentrated Na_(4)Fe(CN)_(6) solution.Both the post-synthetic and in-situ vacancy repaired FeHCF products(FeHCF-P and FeHCF-I)show the significant decrease in the number of vacancy defects and the reinforced structure,which can suppress the side reactions and activate the capacity from low-spin Fe in FeHCF.In particular,FeHCF-P delivers a reversible discharge capacity of 131 mAh g^(−1) at 1 C and remains 109 mAh g^(−1) after 500 cycles,with a capacity retention of 83%.FeHCF-I can deliver a high discharge capacity of 158.5 mAh g^(−1) at 1 C.Even at 10 C,the FeHCF-I electrode still maintains a discharge specific capacity of 103 mAh g^(−1) and retains 75% after 800 cycles.This work provides a new vacancy repairing strategy for the solution synthesis of high-quality FeHCF.

Interface repairing for AA5083/T2 copper explosive composite plate by friction stir processing

Multi-pass friction stir processing(M-FSP)was performed to repair the interface defects of AA5083/T2 copper explosive composite plates.The interface morphology and its bonding mechanism were explored.The results show that higher rotation speed and lower transverse speed produce more heat generated during FSP.The defect-free and good mechanical properties of the AA5083/T2 copper composite plate can be obtained under the condition of the rotation speed of 1200 r/min,the transverse speed of 30 mm/min and the overlap of 2/24.Moreover,M-FSP changes the interface bonding mechanism from metallurgical bonding to vortex connection,improving the bonding strength of composite plate,which can guarantee the repairing quality of composite plates.

The New Technology of Composite Materials Repairing by Light Wave

The repairing of damaged composite materials becomes a hot research subject in the late 1990s.In this paper a new technology of repairing composite materials is given on the basis of our previous research.The light wave of 675nm transmitted by optical fiber is used as repairing light source,special repairable adhesive which can be stimulated by the light is adopted.By comparing the stiffness of the composite material before and after being damaged,it can be concluded that the mechanical property will not be changed with the feasible repairing technology.

Repairing peripheral nerve injury using tissue engineering techniques

Each year approximately 360,000 people in the United States suffer a peripheral nerve injury （PNI）, which is a leading source of lifelong disability （Kelsey et al., 1997; Noble et al., 1998）. The most frequent cause of PNIs is motor vehicle accidents, while gunshot wounds, stabbings, and birth trauma are also common factors. Patients suffering from disabilities as a result of their PNIs are also burdensome to the healthcare system, with aver- age hospital stays of 28 days each year （Kelsey et al., 1997; Noble et al., 1998）.

Compatibility research of laser additive repairing TA15 forgings with Ti6Al4V-xTA15 alloy

The application of mixed powders with different mass fraction on laser additive repairing(LAR)can be an effective way to guarantee the performance and functionality of repaired part in time.A convenient and feasible approach is presented to repair TA15 forgings by employing Ti6Al4V-xTA15 mixed powders in this paper.The performance compatibility of Ti6Al4V-xTA15 powders from the aspects of microhardness,tensile property,heat capacity,thermal expansion coefficient and corrosion resistance with the TA15 forgings was fully investigated.The primaryαlaths were refined and the volume fraction of the secondaryαphase was increased by increasing the mass fraction of TA15 in the mixed Ti6Al4V-xTA15 powders,leading to varied performances.In conclusion,the mixed Ti6Al4V-70%TA15(x=70%)powders is the most suitable candidate and is recommended as the raw material for LAR of TA15 forgings based on overall consideration of the compatibility calculations of the laser repaired zone with the wrought substrate zone.

Progress in the application of cold gas dynamic spraying to repairing continuous casting molds

A new continuous casting mold repairing method--cold gas dynamic spraying （CGDS） is introduced. The study investigates the advantages of the CGDS process regarding repairing operation, such as convenient, in-situ repairation,little heat delivery, microstructural and dimensional stability and other special applications. Microstructure and mechanical properties of the copper alloy coating, nickel coating, ceramic composite coating, and their interface to the substrates ,which are usually used in repairing operation have been researched by means of optical microscopy （ OM）, scanning electron microscopy （SEM）, transmission electron microscopy （TEM） and micro-hardness tests. Experimental results have demonstrated the relative density of the copper alloy coating is as high as 98.7%, and that no obvious difference can be observed between the CrZrCu substrate and the Cu alloy coating in terms of microstructures; thus the interface is quite difficult to be identified. The bonding strength and micro-hardness of the Cu alloy coating reach up to 37 MPa and 310 HV0.2 ,respectively. The interface between the copper alloy coating and the nickel coating is either zigzag or wave shaped, and the cohesion is relatively good. As-sprayed nickel coating is dominated by severely deformed particles,and the relative density is up to 98.5%. Complete recrystallization occurred after annealing at 900℃ for one hour,while its micro-hardness remains as high as 124.1 HV02. All these results have indicated that CGDS is a promising technology for repairing the continuous casting mold and that its future development is prosperous as well.

Laser repairing surface crack of Ni-based superalloy components

Surface crack of components of the cast nickel base superalloy was repaired with twin laser beams under proper technological conditions. One laser beam was used to melt the substrate material of crack, and the other to fill in powder material to the crack region. The experimental results show that the surface crack with the width of 0.1 ～ 0.3?mm could be repaired under the laser power of 3?kW and the scanning speed of 6 ～ 8?mm/s. The repaired deepness of crack region is below 6.5?mm. The microstructure of repaired region is the cellular crystal, columnar crystal dendrite crystal from the transition region to the top filled layer. The phases in repaired region mainly consisted of supersaturated α Co with plenty of Ni, some Cr and Al, Cr 23 C 6, Co 2B, Co Ni Mo, Ni 4B 3, TiSi and VSi. The hardness of filled layer in repaired region ranged from HV 0.2 450 to HV 0.2 500, and the hardness decreases gradually from the filled layer to joined zone.

Biological and artificial nerve conduit for repairing peripheral nerve defect

OBJECTIVE： Recently, with the development of biological and artificial materials, the experimental and clinical studies on application of this new material-type nerve conduit for treatment of peripheral nerve defect have become the hotspot topics for professorial physicians. DATA SOURCES ： Using the terms ＂nerve conduits, peripheral nerve, nerve regeneration and nerve transplantation＂ in English, we searched Pubmed database, which was published during January 2000 to June 2006, for the literatures related to repairing peripheral nerve defect with various materials. At the same time, we also searched Chinese Technical Scientific Periodical Database at the same time period by inputting ＂ peripheral nerve defect, nerve repair, nerve regeneration and nerve graft＂ in Chinese. STUDY SELECTION ： The materials were firstly selected, and literatures about study on various materials for repairing peripheral nerve defect and their full texts were also searched. Inclusive criteria： nerve conduits related animal experiments and clinical studies. Exclusive criteria： review or repetitive studies. DATA EXTRACTION： Seventy-nine relevant literatures were collected and 30 of them met inclusive criteria and were cited. DATA SYNTHESIS ： Peripheral nerve defect, a commonly seen problem in clinic, is difficult to be solved. Autogenous nerve grafting is still the gold standard for repairing peripheral nerve defect, but because of its application limitation and possible complications, people studied nerve conduits to repair nerve defect. Nerve conduits consist of biological and artificial materials. CONCLUSION： There have been numerous reports about animal experimental and clinical studies of various nerve conduits, but nerve conduit, which is more ideal than autogenous nerve grafting, needs further clinical observation and investigation.

Histological observation on acellular nerve grafts co-cultured with Schwann cells for repairing defects of the sciatic nerve

BACKGROUND： Animal experiments and clinical studies about tissue engineering method applied to repair nerve injury mainly focus on seeking ideal artificial nerve grafts, nerve conduit and seed cells. Autologous nerve, allogeneic nerve and xenogeneic nerve are used to bridge nerve defects, it is one of the methods to promote the repair of nerve injury by culturing and growing Schwann cells, which can secrete various neurotrophic factor activities, in the grafts. OBJECTIVE ： To observe the effect of acellular nerve grafts co-cultured with Schwann cells in repairing defects of sciatic nerve. DESIGN： An observational comparative study.SETTING： Tissue Engineering Laboratory of China Medical University.MATERIALS： The experiment was carried out in the Tissue Engineering Laboratory of China Medical University between April 2004 and April 2005. Forty neonatal Sprague-Dawley rats of 5-8 days （either males or females） and 24 male Wistar rats of 180-220 g were provided by the experimental animal center of China Medical University. METHODS： ① Culture of Schwann cells： The bilateral sciatic nerves and branchial plexus were isolated from the 40 neonatal SD rats. The sciatic nerves were enzymatically digested with collagenase and dispase, isolatd, purified and cultured with the method of speed-difference adhersion, and identified with the SABC immunohistochemical method. ② Model establishment： In vitro Schwann cells were microinjected into 10-mm long acellular nerve grafts repairing a surgically created gap in the rat sciatic nerve. According to the different grafted methods, the animals were randomly divided into three groups： autografts （n=8）, acellular nerve grafts （n=8）, or acellular nerve grafts with Schwann cells （n=8）. ③ The regenerated nerve fiber number and average diameter of myeline sheath after culture were statistically anlayzed. MAIN OUTCOME MEASURES： ① The regenerated nerve ultrastructure, total number and density of myelinated nerve fibers, and the thickness of myeline sheath were observed under electron microscope. ② The images were processed with the Mias-1000 imaging analytical system to calculate the number of myelinated nerve fibers, and the thickness of myeline sheath. RESULTS： All the 24 Wistar rats were involved in the analysis of results. ① Results observed under transmission electron microscope： The regenerated myelinated nerve fibers in the group of acellular nerve grafts with Schwann cells were more even than those in the group of acellular nerve grafts, the number of myelinated nerve fibers and thickness of myelin sheath were close to those in the allografts group （P 〉 0.05）, but significantly different from those in the group of acellular nerve grafts （P 〈 0.05）. ② Results observed under scanning electron microscope： A great amount of Schwann cells with two polars were observed in the group of grafts with Schwann cells, the feature of cultured Schwann cells showed shoulder by shoulder, head to head. ③ The number of myelinated nerve fibers and thickness of myelin sheath analyzed by Mias-1000 imaging system in the group of acellular nerve grafts with Schwann cells were close to those in the autografts group （P 〉 0.05）, but significantly different from those in the group of acellular nerve grafts （P 〈 0.05）.CONCLUSION： Host axonal regeneration is significantly increased after implant of acellular nerve grafts. Acellular nerve grafts with Schwann cells offers a novel approach for repairing the gap of nerve defect.

Discussion on Reasonable Supporting Parameters for Repairing Underground Projects in Bulking Soft Rock

Based on analysis of the supporting object of bulking soft rock and comparing the supporting difficulty of the repairing projects with that of the newly excavated projects, this paper proposes a method to determine reasonable supporting parameters for soft rock project repairing. This method has been verified to be reasonable and economical in an industrial test.

Fundamental Research of Repairing Macroscopic Cracking of Ceramic by Directed Metal Oxidation Method

This study focused on testing the possibility of formation of alumina ceramic phase using aluminum/alumina mixture with other low content sintered at high temperature. It was found from XRD and SEM that aluminium is oxidized to alumina completely and the samples formatted ceramic phase accompanying minute expansion. This research supplies a new method of repairing macroscopic cracking of ceramic.

Repairing of Macroscopic Ceramic Cracks by Tiny Expansion Filling Composites

Using SiC, Al, Al_2O_3, ZrO_2 and Y_2O_3 as raw materials, based on chemical reactions those can cause expansion effect to compensate for the sintering shrinkage at elevated temperature among them, such as Al oxidizes to Al_2O_3, SiC converts to SiO_2, and their reaction productions react further to form mullite (3Al_2O_3·2SiO_2), a sort of tiny expansion composites were prepared and designed which can be used to repair macroscopic cracks of sintered ceramics. The total expanding extent can be adjusted by proportion of raw materials or control of sintering temperature. Filling this expandable ceramic ingredient in cracks of real ceramic part in a designed paste state, cracks could be repaired by a re-sintering process.

Repairing the injured spinal cord: sprouting versus regeneration. Is this a realistic match?

The article by Meves and Zheng （2014） is addressing a continu- ous shift in the field of spinal cord injury （SCI） research that has occurred over the last century. Before that, the spinal cord was viewed as ＂hard wired＂ and treatment considerations were based on observations that axons in the periphery were able to regenerate, but those in the central nervous system （CNS） were not （David and Aguayo, 1981）.