A new kind of polycarboxylate superplasticizer with high slump loss resistance was obtained by designing scheduled molecular structure.The number average molecular mass of the polymer was characterized by the gel perm...A new kind of polycarboxylate superplasticizer with high slump loss resistance was obtained by designing scheduled molecular structure.The number average molecular mass of the polymer was characterized by the gel permeation chromatography measurements.And chemical structure of the polymer was observed by the Fourier transform infrared spectroscopy(FT-IR).The results show that the good workable maintaining of self-compacting concrete could be achieved through direct adjustment of number average molecular mass and different unsaturated monomer in synthetic process.The FT-IR analysis illustrated that the high slump loss resistance of polycarboxylate superplasticizers with ester and carboxyl group and expectations of molecular structure were designed.展开更多
Reasonable control on CRI（coke reaction index）is one of the key factors for BF（blast furnace）low-carbon smelting.However,there are contrary opinions.One is increasing CRI to improve reaction efficiency in BF and t...Reasonable control on CRI（coke reaction index）is one of the key factors for BF（blast furnace）low-carbon smelting.However,there are contrary opinions.One is increasing CRI to improve reaction efficiency in BF and the other is decreasing CRI to suppress coke degradation in furnace.Different methods are adopted to realize effective catalysis（increasing CRI）and passivation（decreasing CRI）of coke.Simulation tests of coke in BF lumpy zone under gradual temperature rising have been done.Effect of CRI on gas composition,ore reduction,burden column permeability and heat reserve zone′s temperature under non-isothermal condition are studied.Then combined with iron making calculations,a novel BF operation suggestion is proposed as coke nut with small size be catalyzed and mixed with ore while skeletal coke with large size be passivated and separately charged into BF.展开更多
As technology node shrinks, aggressive design rules for contact and other back end of line（BEOL）layers continue to drive the need for more effective full chip patterning optimization. Resist top loss is one of the m...As technology node shrinks, aggressive design rules for contact and other back end of line（BEOL）layers continue to drive the need for more effective full chip patterning optimization. Resist top loss is one of the major challenges for 28 nm and below technology nodes, which can lead to post-etch hotspots that are difficult to predict and eventually degrade the process window significantly. To tackle this problem, we used an advanced programmable illuminator（FlexRay） and Tachyon SMO（Source Mask Optimization） platform to make resistaware source optimization possible, and it is proved to greatly improve the imaging contrast, enhance focus and exposure latitude, and minimize resist top loss thus improving the yield.展开更多
文摘A new kind of polycarboxylate superplasticizer with high slump loss resistance was obtained by designing scheduled molecular structure.The number average molecular mass of the polymer was characterized by the gel permeation chromatography measurements.And chemical structure of the polymer was observed by the Fourier transform infrared spectroscopy(FT-IR).The results show that the good workable maintaining of self-compacting concrete could be achieved through direct adjustment of number average molecular mass and different unsaturated monomer in synthetic process.The FT-IR analysis illustrated that the high slump loss resistance of polycarboxylate superplasticizers with ester and carboxyl group and expectations of molecular structure were designed.
基金Sponsored by National Natural Science Foundation of China(61271303)Fundamental Research Funds for CentralUniversities of China(FRF-TP-12-029A)
文摘Reasonable control on CRI（coke reaction index）is one of the key factors for BF（blast furnace）low-carbon smelting.However,there are contrary opinions.One is increasing CRI to improve reaction efficiency in BF and the other is decreasing CRI to suppress coke degradation in furnace.Different methods are adopted to realize effective catalysis（increasing CRI）and passivation（decreasing CRI）of coke.Simulation tests of coke in BF lumpy zone under gradual temperature rising have been done.Effect of CRI on gas composition,ore reduction,burden column permeability and heat reserve zone′s temperature under non-isothermal condition are studied.Then combined with iron making calculations,a novel BF operation suggestion is proposed as coke nut with small size be catalyzed and mixed with ore while skeletal coke with large size be passivated and separately charged into BF.
文摘As technology node shrinks, aggressive design rules for contact and other back end of line（BEOL）layers continue to drive the need for more effective full chip patterning optimization. Resist top loss is one of the major challenges for 28 nm and below technology nodes, which can lead to post-etch hotspots that are difficult to predict and eventually degrade the process window significantly. To tackle this problem, we used an advanced programmable illuminator（FlexRay） and Tachyon SMO（Source Mask Optimization） platform to make resistaware source optimization possible, and it is proved to greatly improve the imaging contrast, enhance focus and exposure latitude, and minimize resist top loss thus improving the yield.
