We present the scheme of the structure of grading a resistor-heated system ofwarm compaction in powder metallurgy. The structure has the first heater and the second heater thatare heated by electrical tubes. Powder is...We present the scheme of the structure of grading a resistor-heated system ofwarm compaction in powder metallurgy. The structure has the first heater and the second heater thatare heated by electrical tubes. Powder is heated in turn in the first heater and the second heater,where there is the mass fluidity of powder under gravity. The dimensions of the first heater andthe second heater were calculated from the Fourier equation of heat conduction, and the boundarycondition was constant temperature. The drawings of the first heater, the second heater and thepowder-delivering device were given. The structure of the heat equipment is simple and easy tomanufacture. Finally, an exact warm compaction press system HGWY- II was developed for the heatingsystem.展开更多
IrO2-TiO2 thin films were prepared by atomic layer deposition using Ir（EtCp）（COD） and titanium isopropoxide （TTIP）. The resistivity of IrO2-TiO2 thin films can be easily controlled from 1 500 to 356.7 μΩ·...IrO2-TiO2 thin films were prepared by atomic layer deposition using Ir（EtCp）（COD） and titanium isopropoxide （TTIP）. The resistivity of IrO2-TiO2 thin films can be easily controlled from 1 500 to 356.7 μΩ·cm by the IrO2 intermixing ratio from 0.55 to 0.78 in the IrO2-TiO2 thin films. The low temperature coefficient of resistance（TCR） values can be obtained by adopting IrO2-TiO2 composite thin films. Moreover, the change in the resistivity of IrO2-TiO2 thin films was below 10% even after O2 annealing process at 600 ℃. The step stress test results show that IrO2-TiO2 films have better characteristics than conventional TaN08 heater resistor. Therefore, IrO2-TiO2 composite thin films can be used as a heater resistor material in thermal inkjet printhead.展开更多
文摘We present the scheme of the structure of grading a resistor-heated system ofwarm compaction in powder metallurgy. The structure has the first heater and the second heater thatare heated by electrical tubes. Powder is heated in turn in the first heater and the second heater,where there is the mass fluidity of powder under gravity. The dimensions of the first heater andthe second heater were calculated from the Fourier equation of heat conduction, and the boundarycondition was constant temperature. The drawings of the first heater, the second heater and thepowder-delivering device were given. The structure of the heat equipment is simple and easy tomanufacture. Finally, an exact warm compaction press system HGWY- II was developed for the heatingsystem.
基金supported by a grant from the Fundamental R&D Program for Core Technology of Materials funded by the Ministry of Knowledge Economy, Republic of Koreasupported by Basic Science Research program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education, Science and Technology (2010-0001-226)
文摘IrO2-TiO2 thin films were prepared by atomic layer deposition using Ir（EtCp）（COD） and titanium isopropoxide （TTIP）. The resistivity of IrO2-TiO2 thin films can be easily controlled from 1 500 to 356.7 μΩ·cm by the IrO2 intermixing ratio from 0.55 to 0.78 in the IrO2-TiO2 thin films. The low temperature coefficient of resistance（TCR） values can be obtained by adopting IrO2-TiO2 composite thin films. Moreover, the change in the resistivity of IrO2-TiO2 thin films was below 10% even after O2 annealing process at 600 ℃. The step stress test results show that IrO2-TiO2 films have better characteristics than conventional TaN08 heater resistor. Therefore, IrO2-TiO2 composite thin films can be used as a heater resistor material in thermal inkjet printhead.
