Optimization of Preparation Conditions of Modified Oyster Shell Powder/Ce-N-TiO2 by Response Surface Methodology (RSM)

A new composite photocatalyst of modified oyster shell powder/Ce-N-TiO2 was prepared by sol-gel method. Based on single factor experiment, Ce doping rate, N doping rate and calcination temperature were taken as input variables. Based on the central composite design (BBD) response surface model, two functional relationship models between three independent variables and glyphosate removal rate were established to evaluate the influence degree of independent variables and interaction on catalyst. The significance of the model and regression coefficient was tested by variance analysis. The analysis of the obtained data showed that the degradation performance of the composite photocatalyst was significantly affected by the calcination temperature and the rate of N doping, while the rate of Ce doping had little effect;at the calcination temperature of 505.440°C, the degradation rate of glyphosate reached the maximum of 82.15% under the preparation conditions of 17.057 mol% N doping and 0.165 mol% Ce doping, respectively.

Mechanical and Permeability Analysis and Optimization of Recycled Aggregate Pervious Concrete Based on Response Surface Method

In this paper,the effects of different influencing factors and factor interaction on the compressive strength and permeability of recycled aggregate pervious concrete(RAPC)were studied based on the response surface method(RSM).By selecting the maximum aggregate size,water cement ratio and target porosity as design variables,combined with laboratory tests and numerical analysis,the influences of three factors on the compressive strength and permeability coefficient of RAPC were revealed.The regression equation of compressive strength and permeability coefficient of recycled aggregate pervious concrete were established based on RSM,and the response surface model was optimized to determine the optimal ratio of RAPC under the conditions of meeting the mechanical and permeability properties.The results show that the mismatch item of the model is not significant,the model is credible,and the accuracy and reliability of the test are high,but the degree of uncorrelation between the test data and the model is not obvious.The sensitivity of the three factors to the compressive strength is water cement ratio>maximum coarse aggregate particle size>target porosity,and the sensitivity to the permeability coefficient is target porosity>maximum coarse aggregate particle size>water cement ratio.The absolute errors of the model prediction results and the model optimization results are 1.28 MPa and 0.19 mm/s,and the relative errors are 5.06%and 4.19%,respectively.With high accuracy,RSM can match the measured results of compressive strength and permeability coefficient of RAPC.

Effects of main ecological factors on the growth of marine green alga Caulerpa sertularioides using the response surface methodology

Caulerpa sertularioides is an invasive potential blooming green alga in China but it remains poorly studied.We studied the effects of ecological factors on its growth.Optimum conditions of ecological factors,i.e.,irradiance,temperature,and salinity,for the growth of its fragments were determined in the response surface methodology(RSM).The specific growth rates(SGR)of the fragments were determined in single-factor experiment.The results show that the SGR of C.sertularioides peaked under the conditions of irradiance 37.5μmol/(m~2·s),temperature25℃,and salinity 30.Meanwhile,using the Box-Behnken design,the conditions were further optimized and verified to be:irradiance 39.03μmol/(m~2·s),temperature 25.29℃,and salinity 30.06,under which the SGR reached 4.66%.The results provide new theoretical data and solutions for the cultivation,invasion prediction,and monitoring of Caulerpa species in China and the world.The RSM method may have great potential applications in the environmental adaptation characteristics of new macroalgal cultivars,intensive orientation cultured germplasm,and environmental hazard analysis of cultivated species in the field.

Bamboo Fiber Modified Asphalt Mixture Proportion Design and Road Performances Based on Response Surface Method

In order to comprehensively utilize the remaining bamboo residue of bamboo products,this paper presents a research on recycling the bamboo fibers from bamboo residue for improving the performance of the asphalt mixtures.First of all,the basic performance parameters of sinocalamus affinis fiber,phyllostachys pubescens fiber,green bamboo fiber were tested and analyzed,and the optimal content and length were put forward.Then,the mix ratio design of the bamboo fiber modified asphalt mixture was further designed through the response surface method,and was verified the rationality of the mix ratio.Finally,the mixture specimens were made according to the experimental design mix ratio,and the high temperature,low temperature performance and moisture susceptibility of the bamboo fiber modified mixtures asphalt were tested.The results showed that the high temperature performance,low temperature performance and moisture susceptibility of bamboo fiber modified asphalt mixtures were improved compared with the performance of SBS modified asphalt mixture.When the length of bamboo fiber is 7.25 mm and the content of 0.22%,the road performance of the asphalt mixture was optimal.Consequentially,the decomposition of bamboo residue into bamboo fiber and its application in asphalt pavement can improve the reuse of bamboo waste,with remarkable environmental benefits and great promotion value.

Optimization for Microbial Degumming of Ramie with Bacillus subtilis DZ_(5) in Submerged Fermentation by Orthogonal Array Design and Response Surface Methodology

As a kind of natural fiber,ramie fiber has distinctive advantages in textile application,but the application is limited due to the traditional degumming mode.Compared with the traditional degumming process,the microbial degumming process has many advantages.To obtain the optimal conditions for degumming ramie with Bacillus subtilis DZ_(5)(BS DZ_(5)),a combined statistical approach of orthogonal array design(OAD)and response surface methodology(RSM)was used.The influences of initial pH of the bacteria medium,culture temperature,shaking speed,degumming time and inoculum size on submerged fermentation degumming were evaluated by using fractional factorial design.The main factors in the analysis were culture temperature,shaking speed and initial pH.The residual gum mass fraction was used as the optimization index,and the optimal conditions for degumming were determined by central composite design and RSM.Thus with only a limited number of experiments,an optimal ramie microbial degumming condition was found as the culture temperature of 40℃,the initial pH in the culture medium of 8.5,the shaking speed of 205 r/min,the degumming time of 96 h and the inoculum size of 5%.After microbial degumming of ramie under the optimal conditions,there was only 10.6%residual gum by mass in the fiber.In addition,the effective degumming of BS DZ_(5)was also confirmed by a scanning electron microscope(SEM).

Optimization of Solid-state Fermentation Conditions of Sophora japonica cv.jinhuai by Response Surface Methodology

[Objectives]To optimize the solid-state fermentation process of Flos Sophorae Immaturus by Penicillium with Sophora japonica cv.jinhuai as raw material.[Methods]The fermentation conditions were optimized by single factor experiment and response surface methodology with quercetin content as the dependent variable.[Results]According to the established model,the optimal fermentation process of Flos Sophorae Immaturus was obtained as follows:temperature 29.97℃,time 6.88 d,rotation speed 180.86 rpm,inoculation amount 3.93 mL,and the expected content of quercetin was 34.8053 mg/g.Based on this,the fermentation parameters were adjusted,and the actual content was 33.67 mg/g,which was close to the predicted value.[Conclusions]The optimization of fermentation process of Flos Sophorae Immaturus by response surface methodology provides a reference for the development and utilization of this medicinal material.

Optimization of Supercritical Extraction Process of Laoshan Black Tea by Response Surface Methodology

[Objectives]Laoshan black tea was subjected to supercritical CO_(2) extraction. [Methods]The extraction conditions of Laoshan black tea were studied by an orthogonal experiment and optimized by response surface methodology. [Results] The optimum extraction conditions of black tea extract by supercritical CO_(2) extraction were as follows: extraction pressure 23.53 MPa, extraction time 1.73 h, and extraction temperature 49.75 ℃, with which the extract yield could reach 5.15% theoretically. [Conclusions] Based on the traditional extraction process, a supercritical extraction method optimized by response surface methodology and a unique extraction process were formed, which enriches the extraction processes and methods of natural raw materials.

Optimisation of beef tenderisation treated with bromelain using response surface methodology (RSM)

The purpose of this study is to determine the optimum condition for the tenderization of beef by bromelain using Response Surface Methodology (RSM). Initially, bromelain powder was produced from pineapple crown of variety N36. Production of the bromelain powder involves several process steps such as extraction, purification, desalting and freeze drying. The cube size beef of round part was treated with bromelain at different pHs of beef, immersion temperatures, bromelain solution concentrations, and immersion times according to the experimental design which was recommended by RSM of MINITAB software version 15. Beef tenderness was then measured by Texture Analyser. The MINITAB software Version 15 was used to optimise the tenderisation of beef by bromelain. The determination coefficient R2 was 99.97% meaning that the experimental data were acceptable. It was found that beef could be optimize tenderised 89.907% at the optimum condition at pH of beef of 5.4, immersion temperature of60℃, bromelain solution concentration of 0.1682% and immersion time of 10 minutes. The verification value of beef ten-derisation at the feasible optimum condition which was determined by experiment was 89.571%. Since the difference between the veri- fication and predicted values was less than 5%, therefore, the optimum condition for the tenderisation of beef predicted by MINITAB software Version 15 could be accepted.

Optimization of medium components using response surface methodology (RSM) for mycelium biomass and exopolysaccharide production by <i>Lentinus squarrosulus</i>

The interaction between sucrose, yeast extract and initial pH was investigated to optimize critical medium components for mycelium biomass and production of exopolysaccharide (EPS) of Lentinus squarrosulus using Response Surface Methodology (RSM). A central composite design (CCD) was applied and a polynomial regression model with quadratic term was used to analyse the experimental data using analysis of variance (ANOVA). ANOVA analysis showed that the model was very significant (p Lentinus squarrosulus are as follows: sucrose concentration 114.61 g/L, yeast extract 1.62 g/L and initial pH of 5.81;sucrose concentration 115.8 g/L, yeast extract of 3.39 g/L and initial pH of 6.44 respectively.

Optimization of a continuous ultrasound assisted oxidative desulfurization(UAOD) process of diesel using response surface methodology(RSM) considering operating cost

A continuous-flow ultrasound-assisted oxidative desulfurization(UAOD)of partially hydro-treated diesel has been investigated using hydrogen peroxide-formic acid as simple and easy to apply oxidation system.The effects of different operating parameters of oxidation stage including residence time(2–24 min),formic acid to sulfur molar ratio(10–150),and oxidant to sulfur molar ratio(5–35)on the sulfur removal have been studied using response surface methodology(RSM)based on Box–Behnken design.Considering the operating costs of the continuous-flow oxidation stage including chemical and electrical energy consumption,the appropriate values of operating parameters were selected as follows:residence time of 16 min,the formic acid to sulfur molar ratio of 54.47,and the oxidant to sulfur molar ratio of 8.24.In these conditions,the sulfur removal and the volume ratio of the hydrocarbon phase to the aqueous phase were 86.90%and 4.34,respectively.By drastic reduction in the chemical consumption in the oxidation stage,the volume ratio of the hydrocarbon phase to the aqueous phase was increased up to 10.Therefore,the formic acid to sulfur molar ratio and the oxidant to sulfur molar ratio were obtained 23.64 and 3.58,respectively,which lead to sulfur removal of 84.38%with considerable improvements on the operating cost of oxidation stage in comparison with the previous works.

Removal of Fluoride from Water Using Mesoporous MCM-41: An Optimization Approach Using Response Surface Methodology (RSM)

Fluoride above 1.5 mg·L-1 is injurious to health. Removal of fluoride from water using mesoporous MCM-41 as a strong adsorbent material has been attempted. Characterization using transmission electron microscopic study of calcined MCM-41 showed the regular hexagonal array of mesoporous channels with an average size of 20 nm and the surface area (BET study) of 1306.96 m2·g-1. The average pore size of the particles was found to be 14.21 nm. A study on the effect of contact time on the removal of fluoride revealed that more than 85% uptake of fluoride onto MCM-41 was achieved at a contact time of 120 min. From the Langmuir adsorption study, the maximum sorption capacity of fluoride was found to be 63.05 mg/g at 301 K. From the thermodynamic study, the +ΔHo value of 2.29 kJ·mol-1 indicated the endothermic nature of the removal process. Application of Response Surface Model suggested that 77.88% of fluoride removal can be achieved at fluoride concentration of 10 mg·L-1, pH (6.3), and contact time of 120 min.

Cr(Ⅲ) removal from simulated solution using hydrous magnesium oxide coated fly ash： Optimization by response surface methodology (RSM)

Hydrous magnesium oxide coated fly ash(MFA) has environmental remediation potential by providing a substrate for the adsorption of aqueous Cr(Ⅲ). Aqueous Cr(Ⅲ) adsorption onto MFA was examined as a function of MFA dosage, p H and initial Cr(Ⅲ) concentration with the Box–Behnken approach used for experimental design and optimization using response surface methodology(RSM). p H and dosage(dosage and concentration) have significant interactive effects on Cr(Ⅲ) adsorption efficiency. Analysis of variance shows that the response surface quadratic model is highly significant and can effectively predict the experimental outcomes. Cr(Ⅲ) removal efficiency of 98% was obtained using optimized conditions of MFA dosage, p H and initial Cr(Ⅲ) concentration of 1.57 g·L^(-1), 4.11 and 126 mg·L^(-1), respectively. Cr(Ⅲ) adsorption onto MFA is mainly attributed to the interaction between Cr(Ⅲ) and the functional group \\OH of the hydrous magnesium oxide, in all probability caused by chemisorptions. The results of this study can conduce to reveal the interactions between Cr(Ⅲ) pollutant and MFA characteristics, posing important implications for the cost-effective alternative adsorption technology in the treatment of heavy metal containing wastewater.

Optimization of Multigrain Premix for High Protein and Dietary Fibre Biscuits Using Response Surface Methodology (RSM)

In order to improve the nutritional quality of biscuits, a multigrain premix (MGP) was developed by using whole barley, sorghum, chickpea, pea and defatted soya flour, each at 20% level. The developed MGP had 26.28% protein, 10.13% insoluble dietary fiber and 7.38% soluble dietary fiber. The experiment was designed to optimise the MGP and wheat flour concentration for the development of multigrain biscuits with high protein, dietary fibre and to maximize the acceptability by the application of central composite rotatable design (CCRD) of Response Surface Methodology (RSM). The levels of incorporation of MGP and wheat flour were taken as variables whereas protein, soluble, insoluble fibers, biscuit dough hardness, breaking strength and overall acceptability (OAA) as responses. The optimum level of MGP and wheat flour obtained using numerical optimization was found to be 40 g and 60 g respectively. The biscuits prepared using these had 16.61% protein, 2.57% soluble fibre, and 6.67% insoluble fibre which is significantly (p ≤ 0.05) higher than control biscuit.

Optimization Scale Pasteurization of Baobab Juice Using Response Surface Methodology (RSM)

The Adansonia digitate L. known as Baobab is the only species present in West Africa and grows wild. All parts of the plant are used by humans. In Senegal, baobab pulp is widely consumed;it is used as raw material in small and medium enterprises (SMEs) for making juices, concentrates, jams, powder. Drinks or juices from baobab are highly appreciated by consumers;however rapid fermentation can happen even after pasteurization that can shorten their shelf-life. A Doehlert experimental design was used to find a good scale of heat treatment ensuring a proper conservation of baobab juice. Results of the experimental design showed that a heat treatment of 80&deg;C for 10 min gives a baobab juice with good sanitary quality that meets the international standards.

Synthesis of Poly(AAm-<i>co</i>-AA) and Investigation of its Swelling Behavior: Using Response Surface Methodology (RSM)

Unwanted water production together with oil and gas production is a striking problem in oil and gas industries, and many approaches have been examined to overcome this major problem. Preformed particle gels (PPGs) showed dramatically good properties for this purpose in mature oil and gas reservoirs. In this study, we carefully synthesized an efficient series of PPGs with using a design of experiments (DOE) software. Acrylamide (AAm)/Acrylic acid (AA) mole ratio, N,N’-methylenebisacrylamide (MBA) mole percentage and swelling time were considered as key parameters to examine PPG swelling behavior. Our results presented a detailed empirical correlation, which could significantly predict the swelling capacity of PPGs in CaCl2 salt solution (200,000 ppm).

基于RSM-正交法的磁障式直线永磁游标电机的设计与优化

针对直线永磁游标电机的损耗问题,提出一种磁障式拓扑结构。通过在次级的凸极齿加入隔磁磁障,使次级对磁通的流动具有导向作用,减少涡流损耗,提高电机的磁场调制能力。在此基础上,设计一种磁障式直线永磁游标电机,采用响应面(RSM)-正交法对电机的推力性能进行优化。首先,通过对电机进行灵敏度分析,确定显著变量。其次,根据RSM法建立优化目标响应与显著变量之间的拟合模型,并对其拟合精度进行评估。最后,基于该模型进行正交试验,根据正交试验的数据进行极差分析,得到电机的最优结构参数。有限元实验结果表明,采用RSM-正交优化方法的电机性能得到大幅提高,并且可以节省优化时间,提高优化效率,对直线永磁游标电机的设计与优化有重要的参考价值。

Long-term deformation analysis of Shuibuya concrete face rockfill dam based on response surface method and improved genetic algorithm

Due to the size effects of rockfill materials, the settlement difference between numerical simulation and in situ monitoring of rockfill dams is a topic of general concern.The constitutive model parameters obtained from laboratory triaxial tests often underestimate the deformation of high rockfill dams.Therefore, constitutive model parameters obtained by back analysis were used to calculate and predict the long-term deformation of rockfill dams.Instead of using artificial neural networks (ANNs), the response surface method (RSM) was employed to replace the finite element simulation used in the optimization iteration.Only 27 training samples were required for RSM, improving computational efficiency compared with ANN, which required 300 training samples.RSM can be used to describe the relationship between the constitutive model parameters and dam settlements.The inversion results of the Shuibuya concrete face rockfill dam (CFRD) show that the calculated settlements agree with the measured data, indicating the accuracy and efficiency of RSM.