Lithium Salt Combining Fluoroethylene Carbonate Initiates Methyl Methacrylate Polymerization Enabling Dendrite-Free Solid-State Lithium Metal Battery

This work demonstrates a novel polymerization-derived polymer electrolyte consisting of methyl methacrylate,lithium bis(trifluoromethanesulfonyl)imide and fluoroethylene carbonate.The polymerization of MMA was initiated by the amino compounds following an anionic catalytic mechanism.LiTFSI plays both roles including the initiator and Li ion source in the polymer electrolyte.Normally,lithium bis(trifluoromethanesulfonyl)imide has difficulty in initiating the polymerization reaction of methyl methacrylate monomer,a very high concentration of lithium bis(trifluoromethanesulfonyl)imide is needed for initiating the polymerization.However,the fluoroethylene carbonate additive can work as a supporter to facilitate the degree of dissociation of lithium bis(trifluoromethanesulfonyl)imide and increase its initiator capacity due to the high dielectric constant.The as-prepared poly-methyl methacrylate-based polymer electrolyte has a high ionic conductivity(1.19×10^(−3)S cm^(−1)),a wide electrochemical stability window(5 V vs Li^(+)/Li),and a high Li ion transference number(t_(Li^(+)))of 0.74 at room temperature(RT).Moreover,this polymerization-derived polymer electrolyte can effectively work as an artificial protective layer on Li metal anode,which enabled the Li symmetric cell to achieve a long-term cycling performance at 0.2 mAh cm^(−2)for 2800 h.The LiFePO_(4)battery with polymerization-derived polymer electrolyte-modified Li metal anode shows a capacity retention of 91.17%after 800 cycles at 0.5 C.This work provides a facile and accessible approach to manufacturing poly-methyl methacrylate-based polymerization-derived polymer electrolyte and shows great potential as an interphase in Li metal batteries.

Efficient in-situ end-functionalization of polydienes by isothiocyanate via neodymium mediated coordinative chain transfer polymerization system

End-functionalization of polydiene rubbers can not only improve its compatibility with inorganic fillers,but also enhance the overall mechanical properties.Nevertheless,for traditional neodymium(Nd)diene polymerization systems,it is highly challenging to achieve such end-functionalizations,because most of polydienyl chains are capped withη3-allyl-Nd moiety during the end of polymerization,which shows very poor reactivity with nucleophile compounds.We launched a new diene polymerization strategy calling coordinative chain transfer polymerization(CCTP)[1].In such a system,all the polydienyl chains are capped withη1-allyl-Al moieties,which reveal greater reactivity with cyclic esters and epoxide compounds,providing an effective manner to prepare polydiene-polyester amphiphilic block copolymers.Inspired by such findings,we now show herein how such types of chain-ends react with isot-hiocyanate to demonstrate an efficient in-situ manner to access end-functionalized polydienes by using CCTP.

Influence of external nitrogen-containing donors on polymerization behavior of neodymium-based cis-1,4-polybutadiene rubber

Neodymium(Nd)-based catalyst in butadiene(Bd)polymerization has drawn interests due to its availability in affording higher cis-1,4-unit selectivity than transition metal(Ti,Co,Ni,etc.)-based catalysts[1-2].Such outstanding high cis-1,4-unit selecti-vity is hypothetically originated from the presence of 4 f orbitals,that can participate in monomer coordination and thereby govern subsequent enchainment manners.This unique characteristic also renders the active species highly susceptible to Lewis bases,and may impact the overall selectivity as well as polyme-rization behavior after coordination.Nevertheless,it is still a virgin area in such a field,and the influence of Lewis bases on Nd-based diene polymerizations is still a black box.Based on this consideration,how nitrogen-containing donors(D)impacts the overall behaviors of Nd-mediated Bd polymerizations is disclosed.

Nickel catalysts with asymmetric steric hindrance for ethylene polymerization

α-Diimide catalysts have attracted widespread attention due to their unique chain walking characteristics.A series ofα-diimide nickel/palladium catalysts with different electronic effects and steric hindrances were designed and synthesized for olefin polymerization.In this work,we synthesized a series of asymmetricα-diimide nickel complexes with different steric hindrances and used them for ethylene polymerization.These nickel catalysts have high ethylene polymerization activity,up to 6.51×10^(6)g·mol^(−1)·h^(−1),and the prepared polyethylene has a moderate melting point and high molecular weight(up to 38.2×10^(4)g·mol^(−1)),with a branching density distribution between 7 and 94 branches per 1000 carbons.More importantly,the polyethylene prepared by these catalysts exhibits excellent tensile properties,with strain and stress reaching 800%and 30 MPa,respectively.

3D printing encouraging desired in-situ polypyrrole seed-polymerization for ultra-high energy density supercapacitors

The tireless pursuit of supercapacitors with high energy density entails the parallel advancement of wellsuited electrode materials and elaborately engineered architectures.Polypyrrole(PPy)emerges as an exceedingly conductive polymer and a prospective pseudocapacitive materials for supercapacitors,yet the inferior cyclic stability and unpredictable polymerization patterns severely impede its real-world applicability.Here,for the first time,an innovative seed-induced in-situ polymerization assisted 3D printing strategy is proposed to fabricate PPy-reduced graphene oxide/poly(vinylidene difluoride-cohexafluoropropylene)(PVDF-HFP)(PPy-rGO/PH)electrodes with controllable polymerization behavior and exceptional areal mass loading.The preferred active sites uniformly pre-planted on the 3D-printed graphene substrates serve as reliable seeds to induce efficient polypyrrole deposition,achieving an impressive mass loading of 185.6 mg cm^(-2)(particularly 79.2 mg cm^(-2)for polypyrrole)and a superior areal capacitance of 25.2 F cm^(-2)at 2 mA cm^(-2)for a 12-layer electrode.In agreement with theses appealing features,an unprecedented areal energy density of 1.47 mW h cm^(-2)for a symmetrical device is registered,a rarely achieved value for other PPy/rGO-based supercapacitors.This work highlights a promising route to preparing high energy density energy storage modules for real-world applications.

Two-photon polymerization lithography for imaging optics

Optical imaging systems have greatly extended human visual capabilities,enabling the observation and understanding of diverse phenomena.Imaging technologies span a broad spectrum of wavelengths from x-ray to radio frequencies and impact research activities and our daily lives.Traditional glass lenses are fabricated through a series of complex processes,while polymers offer versatility and ease of production.However,modern applications often require complex lens assemblies,driving the need for miniaturization and advanced designs with micro-and nanoscale features to surpass the capabilities of traditional fabrication methods.Three-dimensional(3D)printing,or additive manufacturing,presents a solution to these challenges with benefits of rapid prototyping,customized geometries,and efficient production,particularly suited for miniaturized optical imaging devices.Various 3D printing methods have demonstrated advantages over traditional counterparts,yet challenges remain in achieving nanoscale resolutions.Two-photon polymerization lithography(TPL),a nanoscale 3D printing technique,enables the fabrication of intricate structures beyond the optical diffraction limit via the nonlinear process of two-photon absorption within liquid resin.It offers unprecedented abilities,e.g.alignment-free fabrication,micro-and nanoscale capabilities,and rapid prototyping of almost arbitrary complex 3D nanostructures.In this review,we emphasize the importance of the criteria for optical performance evaluation of imaging devices,discuss material properties relevant to TPL,fabrication techniques,and highlight the application of TPL in optical imaging.As the first panoramic review on this topic,it will equip researchers with foundational knowledge and recent advancements of TPL for imaging optics,promoting a deeper understanding of the field.By leveraging on its high-resolution capability,extensive material range,and true 3D processing,alongside advances in materials,fabrication,and design,we envisage disruptive solutions to current challenges and a promising incorporation of TPL in future optical imaging applications.

Effect of solvent on the initiation mechanism of living anionic polymerization of styrene:A computational study

For living anionic polymerization(LAP),solvent has a great influence on both reaction mechanism and kinetics.In this work,by using the classical butyl lithium-styrene polymerization as a model system,the effect of solvent on the mechanism and kinetics of LAP was revealed through a strategy combining density functional theory(DFT)calculations and kinetic modeling.In terms of mechanism,it is found that the stronger the solvent polarity,the more electrons transfer from initiator to solvent through detailed energy decomposition analysis of electrostatic interactions between initiator and solvent molecules.Furthermore,we also found that the stronger the solvent polarity,the higher the monomer initiation energy barrier and the smaller the initiation rate coefficient.Counterintuitively,initiation is more favorable at lower temperatures based on the calculated results ofΔG_(TS).Finally,the kinetic characteristics in different solvents were further examined by kinetic modeling.It is found that in benzene and n-pentane,the polymerization rate exhibits first-order kinetics.While,slow initiation and fast propagation were observed in tetrahydrofuran(THF)due to the slow free ion formation rate,leading to a deviation from first-order kinetics.

Synthesis of Branched Polyethylene via Bulky α-Diimine Nickel(II)-Catalyzed Ethylene Chain-Walking Polymerization

The catalysis of olefin polymerization through the chain-walking process is a subject of great interest. In this contribution, the successful synthesis of a Brookhart-type unsymmetrical α-diimine nickel catalyst Ni, which contains both dibenzhydryl and phenyl groups, was determined by X-ray crystallography. The compound has a pseudo-tetrahedral geometry at the Ni center, showing pseudo-C2-symmetry. Upon activation with modified methylaluminoxane (MMAO), Ni1 exhibits high catalytic activity up to 1.02 × 107 g PE (mol Ni h)−1 toward ethylene polymerization, enabling the synthesis of high molecular weight branched polyethylene. The molecular weights and branching densities could be tuned over a very wide range. The polymerization results indicated the possibility of precise microstructure control, depending on the polymerization temperature. The branching densities were decreased with increasing the polymerization temperature.

Synthesis and Characterization of Poly Styrene-Co-Poly 2-Hydroxyethylmethacrylate (HEMA) Copolymer and an Investigation of Free-Radical Copolymerization Propagation Kinetics by Solvent Effects

A series of homo and copolymers of styrene (ST) and 2-hydroxyethyl methacrylate (HEMA) in three different media (bulk, tetrahydrofuran, and benzene) have been investigated by free radical polymerization method. The samples obtained from the synthesis were characterized by Fourier Transform-Infrared spectroscopy (FT-IR), proton nuclear magnetic resonance spectroscopy (1H NMR), atomic force microscopy (AFM), and differential scanning calorimetry (DSC). The results show that the synthesis of the polymers is more feasible under neat conditions rather than solvent directed reaction. Moreover, the DSC data shows that the polystyrene obtained is amorphous in nature and therefore displayed only a glass transition signal rather than crystallization and melting peaks. In addition, this study indicates that homolopolymerization of styrene via free radical polymerization tends to be preferable in less polar solvents like THF than in non-polar solvents like benzene. Benzene might destabilize the formation of the reactive radicals leading to the formation of the products. In summary, the homolpolymerization of styrene is more feasible than the homopolymerization 2-hydroxyethyl methacrylate under the experimental setup used. Styrene is more reactive than 2-hydroxyethyl methacrylate than free radical polymerization reaction due in part of the generation of the benzylic radical intermediate which is more stable leading to the formation of products than alkyl radical which are less stable. Furthermore, polymerization of styrene under neat conditions is preferable in solvent-assisted environments. The choice of solvent for the synthesis of these polymers is crucial and therefore the selection of solvent that leads to the formation of a more stable reaction intermediate is more favorable. It is worth noting that the structure of the proposed copolymer consists of a highly polar and hydrophilic monomer, 2-hydroxyethyl methacrylate and a highly non-polar and hydrophobic monomer, styrene. These functionalities constitute an amphiphilic copolymer with diverse characteristics. A plausible explanation underlying our observations is that the reaction conditions employed in the synthesis of these copolymers might not be the right route required under free radical polymerization.

RING-OPENING POLYMERIZATION OF TRIMETHYLENE CARBONATE CATALYZED BY NOVEL SINGLE COMPONENT RARE EARTH CALIXARENE COMPLEXES

In this paper,ring-opening polymerization of trimethylene carbonate(TMC)with rare earth(Nd,Y,La)ρ-tert- butylcalix[n]arene(n=4,6,and 8)complexes as catalysts has been studied.Poly(trimethylene carbonate)(PTMC)with M_v of 21,400 was produced by bulk polymerization under the conditions as follows:[TMC]_0/[Nd](molar ratio)=1000,80℃, 8 h.Mechanism study reveals that the polymerization proceeds via a coordination mechanism.

Ring-opening Polymerization ofε-Caprolactone Using Lanthanide Tris(4-tert-butylphenolate)s as a Single-component Initiator

The ring-opening polymerization of e-caprolactone (CL) initiated by novel single lanthanide tris(4-tert-butylphenolate)s [Ln(OTBP)3] is reported. Single-component La(OTBP)3 can effectively prepare polycaprolactone (PCL) with over 90% yield and viscosity average molecular weight about 60 x 10 under quite mild conditions: molar ratio of CL to initiator is 1000, 60 C, 2 h in toluene. Mechanism study indicates that the monomer inserts into the growing chain via the break of acyl-oxygen bond of CL.

RING-OPENING POLYMERIZATION OFε-CAPROLACTONE USING LANTHANIDE TRIS(N-PHENYL-3,5-DI-T-BUTYLSALICYLALDIMINATO)S AS SINGLE COMPONENT CATALYST

Ring-opening polymerization of ε-caprolactone has been carried out by using rare earth Schiff base complexes： lanthanide tris（N-phenyl-3,5-di-t-butylsalicylaldiminato）s [Ln（OPBS）3] as single component catalyst for the first time. The influences of different rare earth elements, monomer and catalyst concentration as well as reaction time on the polymerization were investigated. Mechanism studies showed that monomer inserts into the active site with the acyl-oxygen bond scission rather than the break of alkyl-oxygen bond.

SYNTHESIS, CHARACTERIZATION AND RING-OPENING POLYMERIZATION OF CYCLIC (ARYLENE PHOSPHONATE) OLIGOMERS

A series of cyclic (arylene phosphonate) oligomers were prepared by reaction of phenylphosphonic dichloride (PPD) with various bisphenols under pseudo-high dilution conditions via interfacial polycondensation. The yield of cyclic (arylene phosphonate) oligomers is over 85% by using hexadecyltrimethylammoniun bromide as phase transfer catalyst (PTC) at 0 'C . The structures of the cyclic oligomers were confirmed by a combination of matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS) and IR analysis. These cyclic oligomers undergo facile ring-opening polymerization in the melt by using potassium 4,4'-biphenoxide as the initiator to give linear polyphosphonate. Free-radical ring-opening polymerization of cyclic(arylene phosphonate) oligomers containing sulfur linkages was also performed in the melt using 2,2'-dithiobis(benzothiazole) (DTB) as the initiator at 270 °C and the resulting polymer had a Mw, of 8 × 103 with a molecular weight distribution of 4. Ring-opening copolymerization of these cyclic oligomers with cyclic carbonate oligomers was also achieved. The average molecular weight of the resulting copolymer is higher than the corresponding homopolymer and the thermal stability of the copolymer is better than the corresponding homopolymer.

SYNTHESIS OF POLY(5,5-DIMETHYL-1,3-DIOXAN-2-ONE)BY LIPASE-CATALYZED RING-OPENING POLYMERIZATION

Porcine pancreas lipase (PPL) and PPL immobilized on narrow distributed micron-sized glass beads wereemployed successfully for the ring-opening polymerization of 5, 5-dimethyl-1, 3-dioxan-2-one (DTC) for the first time.Different polymerization conditions such as enzyme concentration and reaction temperature were studied. Immobilized PPLexhibits higher activity than native PPL. Along wth the increasing enzyme concentration, the molecular weigh of resultingPDTC decreases. PPL immobilized on narrow distributed micron-sized glass beads has outstanding recyclability. For thethird recycle time, immobilized PPL exhibits the highest catalytic activity and with high activity even after the fifth recyletime for the synthesis of PDTC. The ~1H-NMR spectra indicate that decarboxylation does not occur during the ring-openingpolymerization.

Calcium chloride doped zinc-cobalt metal-cyanide complex:Unexpected highly activity towards ring-opening polymerization of propylene oxide

Highly active calcium chloride（CaCl2） doped Zn-Co^Ⅲdouble metal-cyanide（Ca-DMC） catalysts were firstly reported.Ca-DMCs presented a very higher polymer yield（54 kg polymer/g catalyst） at relative low temperature（80-115℃） toward ringopening polymerization（ROP） of propylene oxide（PO） than did DMC catalysts without modification.

A Series of Rare Earth Phenolates Substituted by Alkyl Groups for D,L-Lactide Ring-Opening Polymerization

Single component rare earth phenolates substituted by various alkyl groups have been prepared and the correlation between the aryloxides＇ structure and catalytic activity in the ring-opening polymerization of D,L-lactide has also been investigated.The catalytic activity of all rare earth aryloxides,characteristics of the ring-opening polymerization as well as polymerization kinetics and mechanism were investigated.The results showed that both phenolates＇ catalytic activities and polymerization characteristics changed regularly,keeping in good concordance with variations in substitutents＇ number on phenol and structure of aryloxide ligands.The stronger ability of electron-donation of alkyl groups,the higher catalytic activity.Moreover,the more numbers of substituted alkyl on phenyl ring,the higher catalytic activity.The analyses of polymer ends revealed that the polymerization proceeded via a coordination-acyl-oxygen bond cleavage-insertion mechanism.

CATIONIC RING-OPENING POLYMERIZATION OF TETRAHYDROFURAN WITH KEGGIN-TYPE HETEROPOLYCOMPOUNDS AS SOLID ACID CATALYSTS

Three Keggin-type heteropolyanions, namely H3PMo12O40-13H2O, （NH4）3PMo12O40·4H2O and H3PW12O40·13H2O were prepared and tested in the ring-opening polymerization reaction of tetrahydrofuran. The effects of the counter-cation （H＋, NH4＋） and the peripheral atoms （Mo, W） on the polymerization were investigated. It has been found that when the protons of H3PMo12O40·13H2O were replaced by the ammonium cations the polymerization rate decreased dramatically. Whereas, when the peripheral atoms （Mo） were replaced by their homologous （W）, the polymerization rate increased twofold. As for the viscosity average molecular weight （My） of polymer products, it was found that the high molecular weight （7930） was obtained by using H3PW12O40·13H2O. The molecular weight （My） obtained by H3PMo12O40·13H2O and （NH4）H3PMo12O40·13H2O was 6470 and 6810, respectively.

The Ring-opening Polymerization of D, L-Lactide Initiated with Stannous Octoate

The ring-opening polymerization of D, L-lactide in the melt was systematically investigated by using stannous octoate as the initiator. The molecular weight of poly (D, L-lactide) was characterized with M,. Mn and Mw respectively. The results indicated that five variables, namely purity of monomer, initiator to monomer ratio, vacuum level, polymerization temperature and polymerization time had different influences on the molecular weight and molecular weight distribution of poly(D. L-lactide).

Tetrahydrosalen backboned gadolinium complex as initiator for the ring-opening polymerization of ε-caprolactone

Tetrahydrosalen ligand was employed in the synthesis of gadolinium complex. The ligand was deprotoned by LiBu, and the afforded lithium salt was reacted with anhydrous GdCl3 to produce the gadolinium complex through salt metathesis. This complex was successfully used to initiate the ring-opening polymerization of ε-caprolactone. The initiation conditions in different temperature, monomer-to-initiator ratio and time were investigated. Under the condition： [ε-caprolactone]：[catalyst] = 600, 56 ℃, toluene： 2 ml, poly（ε-caprolactone） （PCL） with Mw = 11,2782 and PDI = 1.96 was achieved.

RING-OPENING POLYMERIZATION OF TRIMETHYLENE CARBONATE BY CALIX[8]ARENE-NEODYMIUM

Ring-opening polymerization of trimethylene carbonate (TMC) with a rare earth calixarene compound as catalyst has been studied for the first time. The effect of TMC/Nd (molar ratio) and polymerization conditions were investigated in detail. It was found that calix[8]arene-neodymium is a highly effective catalyst for the bulk polymerization of TMC and gives high molecular weight (M-v = 60,000) polymer. The optimum conditions of TMC polymerization were found to be as follows:TMC/Nd (molar ratio) = 2,000, 80 degrees C, 16 h. The polymers were characterized by NMR, GPC and DSC. Studying the mechanism by NMR showed that the polymerization of TMC catalyzed by calix[8]arene-neodymium proceeds via a cationic mechanism.