River Sand Characterization for Its Use in Concrete: A Revue

Despite the gradual professionalization of the construction sector as well as the abundance of sand mining sites offered by the North Kivu, Democratic Republic of Congo Region, ignorance of materials by local builders persists. This is the case of quarries extracting river sand used to make concrete and mortar. However, the dosages of the various constituents are most often chosen on the basis of experience without any prior characterization of this material. This paper presents a comprehensive review of the characterization of river sand for its use in concrete in DRC. The origin and global use of river sand in construction are presented in percentage terms to highlight the importance of river sand as a construction material. The physical properties of river sand, including particle size distribution, bulk density, absolute density, and cleanliness are discussed in detail. The paper examines the effect of variations in river sand properties on concrete behavior, including density and compressive strength. Overall, this paper emphasizes the need to properly characterize river sand before using it in construction to ensure durable, high-quality structures. This will avoid the problems that are observed in particular a bad behavior of the coating on the walls;cracks and crumbling of the beams, lintels, posts and even the ruin of the structures.

Assessment of Bholari River Sand for Its Geotechnical Characterization as Fine Aggregate

Present study is aimed at assessment of Bholari river sand for its geo­technical characterization and suitability as fine aggregate which is being quarried in Jamshoro district,Sindh,Pakistan.For this purpose,sand samples(n=11)were collected from quarry sites and main river channel.Physical properties reveal that Bholari sand is mainly coarse to fine in size(0.2 mm-5 mm).Average values of fineness modulus,specific gravity,bulk density and void content of collected samples are 2.58,2.56,1659.90 kg/m^(3) and 35.12%respectively which varied within the corresponding permissible ranges of ACI(American Concrete Institute).Carbonate content of about 57.59%is also in agreement with corresponding range for fine aggregate.Petrographic examination revealed that Bholari River sand mainly compris­es of quartz and rock fragments with subordinate limestone fragments.As per classification of Dott(1964),Bholari sand is lithic arenite where quartz(50%)occurs as main mineral followed by rock fragments(30%),feldspars(15%)and other opaque minerals(5%).Texturally,the sediments are angu­lar(77%)to sub-round(33%).All these physical properties lie within the range set by National Highway Authority(NHA)and American Standard of Testing Material(ASTM).It is concluded that Bholari River sand is suita­ble for use in concrete mixed with cement and asphalt.

Influence of meandering river sandstone architecture on waterflooding mechanisms: a case study of the M-I layer in the Kumkol Oilfield, Kazakhstan

In order to explore the influence of sandstone architecture on waterflooding mechanisms using the architecture method,and taking as an example the M-I layer of the Kumkol oilfield in the South Turgay Basin,Kazakhstan,we portrayed the architecture features of different types of sandstones and quantitatively characterized heterogeneities in a single sand body in meandering river facies.Based on the waterflooding characteristics of point bar sand and overbank sand according to waterflooded interpretation results in 367 wells and numerical simulation results of well groups,we finally analyzed the remaining oil potential of the meandering river sandstone and pointed out its development directions at the high water cut stage.The result shows that because lateral accretion shale beds are developed inside single sand bodies,the point bar sand is a semi-connected body.The overbank sand is thin sandstone with poor connectivity,small area and fast lateral changes.The heterogeneity of the overbank sand is stronger than the point bar sand.The sandstone architectures control the waterflooding characteristics.In meandering river sandstones,the bottom of the point bar sand is strongly waterflooded,while the top of the point bar sand and most of the overbank sand are only weakly waterflooded or unflooded.The thickness percentage of unflooded zone and weakly waterflooded zone in point bar sand is 40％,and the remaining oil in its top part is the main direction for future development.

The Concert between Geology and Artificial Intelligence:Automatic Identification of Heavy Minerals from River Sand

Heavy minerals with densities higher than 2.8 g.cm-3 are generally considered minor components of sand or sandstone,typically forming 1%of the weight in the samples(Mange and Wright,2007).Heavy-mineral analysis is an effective tool for studying the sedimentary provenance of siliciclastic rocks,reconstructing sedimentary sources to sink routes,subdividing and correlating non-fossiliferous siliciclastic strata.

Density and Strength of Mortar Made with the Mixture of Wood Ash, Crushed Gneiss and River Sand as Fine Aggregate

The main purpose of this paper is to study the feasibility of using wood bottom ash to partially replace natural fine aggregate or crushed gneiss sand in the manufacturing of mortars. The experiment uses wood ash as fine aggregates, which passes through 5 mm sieve, in proportions of 5%, 10%, 15%, 20% and 25% by weight to replace partially river sand and crushed gneiss, and the both sand of the same size as the aggregate respectively. Experimental results show that density of mortar and the compressive strength of mortar decrease globally with the increase in wood ash content. At 56 days, and for all replacements with wood ash, compressive strengths values of mortar obtained with the mixture of wood ash and river sand is greater than 20 MPa, which is not the case for mortar made with crushed gneiss and wood ash. Moreover, for 5% of replacement with wood ash, compressive strengths of mortar obtained with the mixture of wood ash and river sand and the mixture of wood ash and crushed gneiss are respectively 37 MPa and 32 MPa at 56 days. These values satisfied the strength requirements. Hence, 5% replacement of crushed gneiss with wood ash is suggested and could be benefit for mortar. In addition, the replacement of sand by wood ash is preferable with river sand which contains fewer fines than crushed gneiss. The compressive strength of mortar with 25% wood ash + river sand could be suitable.

Granulometric and Mineralogical Characterization of the Sands of the Middle Course of the Kasai River (Territory of Ilebo, Province of Kasai/DR Congo)

The sand bars, in perpetual transformation, observable in the middle course of the Kasai river on the section between the city of Ilebo (pk605) to the confluence of the Loange river (pk525), pose enormous navigability problems. This may be dependent on hydrosedimentological characteristics of the Kasai River. This abundance of sand thus conditions the morphology of the middle course of the Kasai River in the section under our study. It therefore constitutes sedimentary navigation obstacles. The objective of this study is the granulometric and mineralogical characterization of the bar sands of the Kasai River in this study section. Particle size analyzes reveal these are moderately well classified to well classified unimodal sands (Classification coefficient between 1.29 to 1.742) largely presenting grain size symmetry and rarely fine asymmetry (Asymmetry coefficient—Skewness between −0.197 to 0.069) with mesorkurtic and rarely leptokurtic and platykurtic acuity (Angulosity coefficient—Kurtosis between 0.814 to 1.323). All these parameters evolve in sawtooth patterns from upstream to downstream. And then, an automated mineralogical analysis of the sands of the Kasaï River using a Qemscan FEG Quanta 650 made it possible to determine a very varied mineralogical procession with a sawtooth evolution. It is largely dominated by quartz (between 93.73% and 99.07%), followed by calcite (0.01% - 2.66%), iron oxides (0.01% - 1.88%), orthoclase (0.04% - 0.99%), plagioclase (0.01% - 0.75%) and Kaolinite (0.18% - 0.71%). Finally, this mineralogical procession is characterized by a group of minerals which do not reach the threshold of 0.55% such as: illite, apatite, ilmenite, muscovite, chlorite, biotite, montmorillonite, rutile, pyrophyllite, siderite, zircon and dolomite. The evolution of the mineralogical procession of the sands of the bars is not as clear as in the case of particle size parameters.

南非林波波带中央带Sand River地区高压麻粒岩变质作用

南非林波波带中央带Sand River地区存在高压基性麻粒岩,其峰期矿物组合为石榴石＋单斜辉石＋石英＋钛铁矿＋磁铁矿。岩石学研究表明,该高压麻粒岩经历了两期退变质作用,早期退变质阶段以斜方辉石和斜长石的出现为特征,晚期退变质阶段以角闪石的出现为特征。传统温压计计算表明：高压麻粒岩峰期变质温度为820℃~900℃,压力为13.5~15.4kbar;早期退变质的形成温压为800℃~890℃和8.8~11.2kbar;晚期退变质条件为540℃~650℃和2.7~4.4kbar。其退变质作用P-T轨迹为顺时针型近等温降压到降温降压的过程。高压麻粒岩经历的这种顺时针P-T轨迹通常发育在大陆碰撞环境,指示其形成可能与津巴布韦克拉通、卡普瓦尔克拉通在碰撞后地壳快速剥露事件有关,这对探讨林波波带中央带的构造演化具有重要意义。

Braided river and distribution patterns of sand bodies of Jurassic Badaowan formation in Block T13 of Junggar basin

In order to determine the planar and volume distribution of sand bodies of the Jurassic Badaowan formation in Block T13 of Junggar basin,we used analysis of field outcrop and 3D seismic data,which play an essential role in areas of sparse well coverage.We describe sedimentary facies characteristics,sand body planforms,width and connectivity patterns of sand bodies,and vertical associations and successions by acoustic impedance inversion technology and sedimentological theory.Results of our study show braided fluvial strata deposits in the Jurassic Badaowan formation.Each sand body is approximately lenticular in shape.The width of each sand body falls in the range 100～800 m,with most between 200 and 400 m.The sand bodies vary in thickness from 4 to 13 m,with most below 9 m.The width/thickness ratios lie in the range 20～55.The connectivity of braided fluvial channel sand bodies is controlled by changes of accommodation space.One fining-upward sedimentary cycle of base-level rise is recognized in Badaowan formation,representing an upward rise of base level.The connectivity of sand bodies was found to be greatest in the early stage of base-level rise,becoming progressively worse with increasing base-level rise.

Impacts of the large amount of sand mining on riverbed morphology and tidal dynamics in lower reaches and delta of the Dongjiang River

The sand dredging and its impacts on riverbed evolution and tidal dynamic change in the lower reaches and delta of the Dongjiang River are examined in this paper. The large amount of sand, totally 3.32 billion m^3 from 1980 to 2002, was mined from the riverbeds of the lower reaches and delta of the Dongjiang River. Increasing of the channel capacity, lowering of the average riverbed elevation, deepening of the water depth and decreasing of the longitudinal riverbed gradient are the main effects on the riverbed evolution brought by the large amount of sand dredging. Under the strong sand dredging and associated significant riverbed deformation, the notable changes of the tidal dynamic in the lower reaches and delta of the Dongjiang River occurred, including： （1）in the upper reaches of the Dongjiang River delta and lower reaches of the Dongjiang River, tidal level dropped apparently, tidal range widened, flood tidal duration became longer, amplitudes for major tidal components became bigger and tidal dynamics intensified; （2） tidal wave spread faster; and （3） the limits of the tidal level, tidal current and salt water moved upstream.

Agglomeration Characteristics of River Sand and Wheat Stalk Ash Mixture at High Temperatures

The agglomeration characteristics of river sand and wheat stalk ash mixture at various temperatures are investigated using a muffle furnace. The surface structural changes, as well as the elemental makeup of the surface and cross-section of the agglomerates, are analyzed by polarized light microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray (EDX). Multi-phase equilibrium calculation is performed with FactSage in identifying the melting behavior of the river sand-wheat stalk ash mixture at high temperatures. No indication of agglomeration is detected below 850°C. At a temperature of 900-1000°C, however, obvious agglomeration is observed and the agglomerates solidify further as temperature increases. The presence of potassium and calcium enrichment causes the formation of a sticky sand surface that induces agglomeration. The main component of the agglomerate surface is K_2O-CaO-SiO_2, which melts at low temperatures. The formation of molten silicates causes particle cohesion. The main ingredient of the binding phase in the cross-section is K_2O-SiO_2-Na_2O-Al_2O_3-CaO; the agglomeration is not the result of the melting behavior of wheat stalk ash itself but the comprehensive results of chemical reaction and the melting behavior at high temperatures. The multi-phase equilibrium calculations agree well with the experimental results.

Cold events of Holocene indicated by primary elements distribution of the high-resolution sand dunes in the Salawusu River Valley

The components of the primary elements in the dune sands for the MGS1 subsection of the Milanggouwan section in the Salawusu River valley, compared with those of modern dune sands, show that they were caused by East Asian winter monsoon in the Mu Us desert during Holocene. The examined ages for the 11 layers of dune sands, based on the average sedimentary rate, are： 0 to 960, 1350-2240, 2470 to 3530, 4000 to 4180, 4290 to 4350, 4380 to 4760, 5040 to 5920, 6570 to 8270, 9020 to 9700, 9880 to 10160 and 10580 to 11080 a BP, respectively. The climatic events indicated by these dune sands are consistent with those records in the Huguangyan volcanic lake, Zoige peat bog, Hulu cave and Dunde ice core, particularly with the climatic fluctuations of the North Atlantic since 11 000 a BP. Among them, patterns from B0 to B8 correspond to the peak values of 0MD, 2D, 4D, 6D＋8D＋10D, 12D, 14D, 16D, 18D and 20D respectively. It might be caused by the North Atlantic ice age induced by the heat circulation, which strengthened the polar high pressure and Siberian-Mongolian high pressure and further led to the dominance of the winter monsoon over China＇s desert area.

A topological pattern research on recent evolution of sand spit at the Huanghe River mouth by using remote sensing informations

By using satellite remote sensing informations, the conceptual system of time-space at tributes and time dimension in recent evolution of the sand spit at the Huanghe River mouth is expound ed. Based on this work, the parameterization of relevant factors and topological analysis of sand spit spa tial structure are conducted, and a model, which is suitable for representing the development and growth of the Huanghe River mouth is developed. It is shown that during the later stage of its development, the Sand spit growth index is almost 0. According to the parallelogram rule, under the reinforce effects of the Coriolis force and ocean dynamics, the Sand spit of current stream will never extend towards sea when it reaches the deep-water area. This work would be helpful to the imminent comprehensive harness of the 'man-made river branch' at the Huanghe River mouth.

Control in Beach and Dune Sands of the Gulf of Mexico and the Role of Nearby Rivers

A sedimentological, petrographic, and geochemical study of beach, dune, and river sands was carried out along the northwestern Gulf of Mexico. The main goal of this work is to show how beach and dune sands are controlled texturally, compositionally, and chemically by the nearby rivers for each beach location using a particle size analyser, a polarized microscope, a X-ray fluorescence and ICP mass spectrometer to obtain the following: grain-size values from one river (Carrizal River) are similar in range to their counterpart beach sands but not similar to the dune sands (Barra del Tordo). Rivers (Panuco and Carrizal) are compositionally controlling the quartz and feldspar contents of their counterpart beach and dune sands (i.e., Playa Miramar and Barra del Tordo). Rivers (Soto La Marina River) are directly influencing the composition of the beach sands (La Pesca) based upon the total quartz content, beach and dune sands. The concentration of magnetite grain fractions (Barra del Tordo beach and dune sands) is not under the influence of the nearby river (Carrizal River). In this case the compositional influence of beach and dune sands is related to sediment discharges by other fluvial systems, redistribution of the beach and dune sands along the coast and deflation/winnowing of light minerals. The Eu positive anomaly in the beach and dune sands from the three sites (i.e. Playa Miramar, Barra del Tordo, La Pesca) is linked to an increase in the P(plagioclase)/K(potash feldspar) ratio. The (La/Lu)cn highest ratio for river sands (Carrizal River) suggests quartz enrichment compared to their beach and dune sands counterparts. The (Gd/Yb)cn ratio for one river (i.e., Carrizal River) indicates that it is low in heavy rare earth elements. HREE compared to their beach and dune sands counterparts indicates less concentration of heavy minerals as potential carriers of HREE seawards.

Sedimentary characteristics of paleo-aeolian dune sands of Salawusu Formation in the Salawusu River Valley

The Salawusu Formation of Milanggouwan section in Salawusu River Valley includes 7 layers of paleo-mobile dune sands, and 4 layers of paleo-fixed and semi-fixed dune sands. Their structures have been observed and their grain size, surface textural features and several main chemical elements have been analyzed. The results showed that： 1） Some of the aeolian structural characteristics of these dune sands are similar to that of the recent dune sands. 2） They are also similar to the recent dune sands in grain size components, and parameters of Mz,σ, Sk and Kg, as well as in several main chemical components. 3） The scattergrams of Mz-σ and SiO2-Al2O3＋TOFE and the probability curves of grain size showed that these paleo-dune sands are different from paleosols and fluvio-lacustrine facies, but are consistency with recent dune sands. 4） Quartz sands have well roundness and surface textural features such as dish-shaped pits, crescent-shaped pits, pockmarked pits, upturned cleavage plates, siliceous precipitates and siliceous crevasses, indicating that they had been carried for a long time by the wind. As the 11 layers of paleo-dune sands possess the aeolian characteristics in structure, grain size, surface textural features and chemical elements, the origin of their formation should be attributed to eolation.

Heavy Minerals in Sands along Brahmaputra (Jamuna) River of Bangladesh

Sands along Brahmaputra River of Bangladesh have long been considered to be a source of heavy minerals (HMs) since it traversed a long way through various terrains. An attempt has been made under this research work to determine the kinds and amounts of heavy minerals in the sands sourced from the river system. Samples from 14 locations along Brahmaputra River covering 30 km distance from upstream to downstream of the river are found to contain different heavy minerals concentration with a range of 7.92 - 25.16 weight% with the remaining of the sample comprising silicate and aluminosilicates. Mineral characterization from peak positions in diffractogram of X-ray Diffraction (XRD) evaluate quartz, feldspar and mica are major categories light mineral while rutile, magnetite, illmenite, zircon, monazite, garnet, uranium arsenide and uranium fluoride are the major types heavy minerals. Ilmenite and rutile are main contributors of total heavy mineral (THM). Titanium bearing minerals ilmenite and rutile contributes 26.22% - 31.01% and 14.57% - 23.50% of THM. In the present study area, most of the sands are found to be fine and medium grained as obtained from the particle sizes analysis using 18- to 230-mesh.

Heavy Minerals in Sands along Brahmaputra (Jamuna) River of Bangladesh

Sands along Brahmaputra River of Bangladesh have long been considered to be a source of heavy minerals (HMs) since it traversed a long way through various terrains. An attempt has been made under this research work to determine the kinds and amounts of heavy minerals in the sands sourced from the river system. Samples from 14 locations along Brahmaputra River covering 30 km distance from upstream to downstream of the river are found to contain different heavy minerals concentration with a range of 7.92 - 25.16 weight% with the remaining of the sample comprising silicate and aluminosilicates. Mineral characterization from peak positions in diffractogram of X-ray Diffraction (XRD) evaluate quartz, feldspar and mica are major categories light mineral while rutile, magnetite, illmenite, zircon, monazite, garnet, uranium arsenide and uranium fluoride are the major types heavy minerals. Ilmenite and rutile are main contributors of total heavy mineral (THM). Titanium bearing minerals ilmenite and rutile contributes 26.22% - 31.01% and 14.57% - 23.50% of THM. In the present study area, most of the sands are found to be fine and medium grained as obtained from the particle sizes analysis using 18- to 230-mesh.

The Influence of Alluvial Mining on the Morphology and Ecological Health of the Jhimruk River in Pyuthan, Nepal

Historically, alluvial rivers have been a desirable source of sediment for various industrial purposes. However, the demand for sand is rapidly increasing, leading to environmental concerns associated with its extraction. The extraction of sediment from riverbeds has both visible and invisible effects. This research aims to investigate the dynamics of the Jhimruk River’s morphology and its impacts by evaluating the river’s quality and studying its changing morphology. To assess morphological changes, satellite images from different years were compared using Geographic Information System (GIS). Physical assessments were conducted by calculating a Habitat score based on various parameters. Water quality assessments involved measuring factors such as pH, temperature, nitrate levels, and alkalinity. A water quality map of the river was generated using color coding to indicate different conditions. The Habitat score demonstrated variations in the data collected from all sites, with factors such as instream cover, bottom substrate stability, riparian vegetation, and aesthetic of the river stretch playing crucial roles in influencing the total score. The Water Quality Index value for the disturbed site indicated moderate pollution, falling under class II. Aquatic macroinvertebrates displayed natural responses to increasing levels of stressors across their life stages, as observed through the analysis of the GRS-BIOS/ASPT index. With the exception of the disturbed site, all other sites were classified under water quality class II, while the disturbed site belonged to class III, indicating a moderate to critically polluted state for most of the Jhimruk River. Furthermore, an increase of 180.87 meters in the river width at the disturbed site provided evidence of morphological changes occurring over the specified period. Mining activities were identified as a significant contributor to the alteration in river morphology.

长江武汉段天兴洲低滩沉积物粒度端元对河流-风成沙丘沉积环境的指示意义

河床沙波向风成沙丘演变的过程具有特殊的沉积动力机制。笔者等以68份长江武汉段天兴洲洲头低滩沉积物的粒度分布数据为例,利用端元分析方法从每个粒度分布中分离提取4个粒度端元组分(EM1、EM2、EM3和EM4),探讨了河流—风成沙丘不同沉积环境中粒度端元的异同。研究结果表明:EM1和EM3组分在粒度分布中占比与沉积物粒度中值分别呈较好的线性正相关和负相关;河流沉积物主要由EM1、EM2和EM3组成的跳跃方式搬运,对应滚动次总体的EM4组分占比5%~10%,少悬浮搬运;风成沙纹沉积物主要包括两段跳跃次总体,以EM2组分为主、EM1和EM3组分为辅,少EM4组分;沙丘背风面沉积物主要靠颗粒流顺坡滑塌,以EM2组分为主、EM1和EM3组分为辅,含占比约为5%的EM4组分;未被风成沙纹覆盖的沙丘波谷沉积物记录了河流和小型滞水洼地的沉积特征,代表滚动次总体的EM4组分占比7%~15%,悬浮次总体占比可达20%。本文提取的沉积物粒度端元为弱风环境中河道内局部小型河流—风成沙丘的沉积环境和演化过程研究提供了参考。

辫状河—曲流河河型转换前后砂体差异性研究——以东营凹陷东辛地区东二段为例

不同河流相砂体形态特征和分布规律差异较大,河型的转换主控了不同时期砂体平面分布特征、几何参数及纵向叠置关系,进而决定了不同河流相类型储层的油气勘探与开发策略。基于东营凹陷东辛地区东二段岩心、测井曲线、三维地震等资料,借助定量岩心沉积构造、定量地震地貌等方法,得出以下结论:1)东二段4,3,2砂组主要发育辫状河沉积,1砂组主要发育曲流河沉积。2)东二段4,3,2砂组辫状河平均河道深度分别为17~52,20~59,19~52 m,平均河道宽度分别为1589~11602,2154~14597,1862~11923 m,定量地震地貌分析指示河道带宽度介于1000~7000 m;1砂组曲流河平均河道深度为11~30 m,平均河道宽度为665~4221 m,定量地震地貌分析指示河道带宽度介于700~3000 m。3)东二段4,3,2砂组辫状河砂体垂向以接触叠置式、下切叠置式为主,横向以独立接触式、侧切接触式、对接接触式为主;1砂组曲流河砂体垂向以分隔叠置式为主,横向以独立接触式为主。明确砂体几何形态及时空切叠方式,为东辛地区东二段河流相砂岩储层的勘探与开发提供了实际支撑。