Creep properties of bimetal Al/SiC/Cu compositesfabricated via accumulative roll bonding process

In the present study,microstructural evolution,mechanical and creep properties of Al/SiC/Cu composite stripsfabricated via accumulative roll bonding(ARB)process were studied.The obtained results showed the formation of anatomic diffusion layer with thickness of about 17μm at the interface during the ARB under three creep loadingconditions namely 30 MPa at 225℃,35 MPa at 225℃,and 35 MPa at 275℃.An generated intermetallic compoundresulted in a 40%increase of interface thickness near Al.The stress level decreased by 13%at constant temperature withno signi fi cant effect on the interface thickness,and the creep failure time declined by 44%.It was observed that atconstant temperatures,the second slope of the creep curve reached to 39%with increasing stress level,then,it dropped to2%with a little temperature rising.After creep test under 35 MPa at 275℃,the sample displays the presence of 60%Aland 40%Cu,containing brittle Al_(2)Cu intermetallic compound at the interface.Applied temperature and stress had effecton the creep properties,specially increasing the slope of creep curves with higher stresses.

Carbon Fiber Breakage Mechanism in Aluminum(Al)/Carbon Fibers(CFs) Composite Sheet during Accumulative Roll Bonding(ARB) Process

We put forward a method of fabricating Aluminum(Al)/carbon fibers(CFs) composite sheets by the accumulative roll bonding(ARB) method. The finished Al/CFs composite sheet has CFs and pure Al sheets as sandwich and surface layers. After cross-section observation of the Al/CFs composite sheet, we found that the CFs discretely distributed within the sandwich layer. Besides, the tensile test showed that the contribution of the sandwich CFs layer to tensile strength was less than 11% compared with annealed pure Al sheet. With ex-situ observation of the CFs breakage evolution with-16%,-32%, and-45% rolling reduction during the ARB process, the plastic instability of the Al layer was found to bring shear damages to the CFs. At last, the bridging strengthening mechanism introduced by CFs was sacrificed. We provide new insight into and instruction on Al/CFs composite sheet preparation method and processing parameters.

Enhanced mechanical properties of lamellar Cu/Al composites processed via high-temperature accumulative roll bonding

Cu/Al multilayers were produced by high-temperature accumulative roll bonding(ARB)methods up to three passes.To achieve a high bonding strength,prior to ARB processing,the Cu and Al sheets were heated to 350,400,450 and 500 ℃,respectively.The mechanical properties were evaluated by tensile tests.The microstructure was examined by optical microscopy and scanning electron microscopy equipped with energy dispersive spectrometry.The ultimate tensile stress,the grain size and the thickness of diffusion layer of lamellar composites increase with rolling temperature.When the rolling temperature is 400 ℃,the laminates show the highest ductility,but the yield stress is the lowest.As the rolling temperature further increases,both the yield stress and the ultimate tensile stress increase and the ductility decreases slightly.The mechanical properties of lamellar composites processed by low and high temperature ARB are determined by grain size and the thickness of diffusion layer,respectively.

Fabrication of ultrafine-grained AA1060 sheets via accumulative roll bonding with subsequent cryorolling

Ultrafine-grained(UFG)AA1060 sheets were fabricated via five-cycle accumulative roll bonding(ARB)and subsequent three-pass cold rolling(298 K),or cryorolling(83 K and 173 K).Microstructures of the aluminum samples were examined via transmission electron microscopy,and their mechanical properties were measured via tensile and microhardness testing.Results indicate that ultrafine grains in ARB-processed sheets were further refined by subsequent rolling,and the grain size became finer with reducing rolling temperature.The mean grain size of 666 nm in the sheets subjected to ARB was refined to 346 or 266 nm,respectively,via subsequent cold rolling or cryorolling(83 K).Subsequent cryorolling resulted in ultrafine-grained sheets of higher strength and ductility than those of the sheets subjected to cold rolling.

Strength prediction of multi-layered copper-based composites fabricated by accumulative roll bonding

This work aims to evaluate the feasibility of the fabrication of nanostructured Cu/Al/Ag multi-layered composites by accumulative roll bonding(ARB),and to analyze the tensile properties and electrical conductivity of the produced composites.A theoretical model using strengthening mechanisms and some structural parameters extracted from X-ray diffraction is also developed to predict the tensile strength of the composites.It was found that by progression of ARB,the experimental and calculated tensile strengths are enhanced,reach a maximum of about 450 and 510 MPa at the fifth cycle of ARB,respectively and then are reduced.The electrical conductivity decreased slightly by increasing the number of ARB cycles at initial ARB cycles,but the decrease was intensified at the final ARB cycles.In conclusion,the merit of ARB to fabricate this type of multi-layered nanocomposites and the accuracy of the developed model to predict tensile strength were realized.

Formation mechanism and control of aluminum layer thickness fluctuation in embedded aluminum-steel composite sheet produced by cold roll bonding process

The influences of rolling reduction and aluminum sheet initial thickness(AIT)on the thickness fluctuation of aluminum layer(TFA)of embedded aluminum?steel composite sheet produced by cold roll bonding were investigated,the formation mechanism of TFA was analyzed and method to improve the thickness uniformity of the aluminum layer was proposed.The results showed that when the reduction increased,TFA increased gradually.When the reduction was lower than40%,AIT had negligible effect on the TFA,while TFA increased with the decrease of AIT when the reduction was higher than40%.The non-uniformities of the steel surface deformation and the interfacial bonding extent caused by the work-hardened steel surface layer,were the main reasons for the formation of TFA.Adopting an appropriate surface treatment can help to decrease the hardening extent of the steel surface for improving the deformation uniformity during cold roll bonding process,which effectively improved the aluminum thickness uniformity of the embedded aluminum/steel composite sheets.

Processing of nanostructured metallic matrix composites by a modified accumulative roll bonding method with structural and mechanical considerations

Particulate reinforced metallic matrix composites have attracted considerable attention due to their lightweight, high strength, high specific modulus, and good wear resistance. A1/B4C composite strips were produced in this work by a modified accumulative roll bonding process where the strips were rotated 90° around the normal direction between successive passes. Transmission electron microscopy and X-ray diffraction analyses reveal the development of nanostructures in the Al matrix after seven passes. It is found that the B4C reinforcement distribution in the matrix is improved by progression of the process. Additionally, the tensile yield strength and elongation of the processed materials are increased with the increase of passes.

Texture evaluation in AZ31/AZ31 multilayer and AZ31/AA5068 laminar composite during accumulative roll bonding

This article presents the texture development of magnesium AZ31 alloy in the accumulative roll bonded(ARB) AZ31/AZ31 multilayer and AZ31/AA5086 laminate composite.The comparative study demonstrates that the texture evolution in AZ31 in a multilayer system is strongly influenced by the interfaces.A typical basal texture of AZ31 has been observed in AZ31/AZ31 multilayer with texture intensity increased with the rolling deformation.Presence of AZ31/AA5086 interface in the laminate composite leads to a tilted basal texture along the rolling direction(RD) in AZ31 alloy.The texture intensity of composite increased initially with rolling reduction and weakened at the higher rolling strain.Weakening of texture in AZ31 during the laminate processing at higher strain has been attributed to the development of wavy interfaces in AZ31/AA5086 laminate.

Bonding enhancement of cold rolling TA1 P-Ti/AA6061 composite plates via surface oxidation treatment

TA1 P-Ti/AA6061 composite plate was produced by oxidizing the surface of the titanium plate and adopting a cold roll bonding process.The results revealed that the oxide film(Ti6O)prepared on the surface of TA1 pure titanium was easy to crack during the cold roll bonding,thereby promoting the formation of an effective mechanical interlock at the interface,which can effectively reduce the minimum reduction rate of the composite plates produced by cold rolling of titanium and aluminium plates.Moreover,the composite plate subjected to oxidation treatment exhibited high shear strength,particularly at a 43%reduction rate,achieving a commendable value of 117 MPa.Based on oxidation treatment and different reduction rates,the annealed composite plates at temperatures of 400,450,and 500°C displayed favorable resistance to interface delamination,highlighting their remarkable strength-plasticity compatibility as evidenced by a maximum elongation of 31.845%.

Development of accumulative roll bonding for metallic composite material preparation and mechanical/functional applications

Accumulative roll bonding(ARB)is a severe plastic deformation method to prepare the metallic composite material by physical method at room to elevate temperature,without the generation of additional waste solid or gas.With the physical characteristicsmulti-material and hybrid structure,the mechanical and function properties of the ARB composite material,like Al/steel,Al/Mg,Al/Cu,etc.,shall have the"1+1>2"effect on the mechanical and functional properties,including the remarkable properties that include lightweight,high strength,thermal/electrical conductivity,electromagnetic shielding,and other functions.To deeply investigate the preparation method and microstructural evolution of various metal laminates by ARB,as well as the mechanical and functional properties of the laminate,an overview of the history of ARB technique,the breakthrough of ARB sheet properties,as well as the relative products in industries is provided.Addi-tionally,the future development of ARB technology and the utilization of composite materials in different areas will be discussed.

Microstructures and Mechanical Properties of Al/Mg Alloy Multilayered Composites Produced by Accumulative Roll Bonding

Al/Mg alloy multilayered composites were produced successfully at the lower temperature（280 C） by accumulative roll bonding（ARB） processing technique.The microstructures of Al and Mg alloy layers were characterized by scanning electron microscopy and transmission electron microscopy.Vickers hardness and three-point bending tests were conducted to investigate mechanical properties of the composites.It is found that Vickers hardness,bending strength and stiffness modulus of the Al/Mg alloy multilayered composite increase with increasing the ARB pass.Delamination and crack propagation along the interface are the two main failure modes of the multilayered composite subjected to bending load.Strengthening and fracture mechanisms of the composite are analyzed.

Interfacial bonding mechanism of Cu/Al composite plate produced by corrugated cold roll bonding

Corrugated cold roll bonding(CCRB) produces metal composite plate with improved mechanical properties compared with conventional methods,but the interfacial mechanism is not fully understood.Here,Cu/Al composite plate with good plate shape was produced by CCRB,and the bonding mechanism and strength along the corrugated interface were studied by experiments and finite element simulations.The results showed that the average bonding strength of Cu/Al composite plate produced by CCRB was nearly twice that of conventional composite plate at an average reduction of 40% during rolling.Strong friction shear stresses occurred at the interface of the corrugated composite plate,which promoted the plastic deformation of the metals and accelerated the rupture of the brittle interfacial layer.Electron backscattered diffraction analysis showed that higher degrees of grain elongation and refinement occurred in the matrices at the front waist and trough due to the stronger normal and shear stresses.Energy-dispersive spectroscopy line scans showed that the thickest atomic diffusion layer occurred at the front waist.The present combination of experimental and computational analyses provides insights into the underlying mechanism of mechanically improved metal composites prepared by CCRB.

Fabrication of Ti/Al/Mg laminated composites by hot roll bonding and their microstructures and mechanical properties

Ti/Al/Mg laminated composites were successfully fabricated by hot roll bonding.The effects of the rolling reduction on the microstructural evolution and mechanical properties of the composites were explored.The results show that Ti/Al/Mg laminated sheets exhibit good interfacial bonding.The rolling reduction has a significant effect on the deformation inhomogeneity through the thickness of the Al layer.The initial grains of the Al layer near the Ti/Al interface are fragmented into fine equiaxed grains,and the grains at the center and near the Al/Mg interface are elongated.The R-cube shear texture of the Al layer forms near the Ti/Al interface and permeates into the center layer in the samples with greater rolling reductions.The b-fiber rolling texture of the Al layer is observed near the Al/Mg interface and increases with the increase of rolling reduction.The stress–strain curves indicate that the fracture appears first in the Mg layer.With the increasing rolling reduction,the ultimate tensile and yield strength values increase,and the elongation up to the Mg layer fracture decreases.

Recent advances and trends in roll bonding process and bonding model:A review

This review presents a thorough survey of the roll bonding process with a focus on the bimetallic bars/tubes as well as the bonding models and criteria.The review aims to provide insight into cold,hot and cryogenic bonding mechanisms at the micro and atomic scale and act as a guide for researchers working on roll bonding,other joining processes and bonding simulation.Mean-while,the shortcomings of roll bonding processes are presented from the aspect of formable shapes,while bonding models are shown from the aspect of calculation time,convergence,interface behav-ior of dissimilar materials as well as hot bonding status prediction.Two well-accepted numerical methodologies of bonding models,namely the contact algorithm and cohesive zone model(CZM)of bonding models and in simulations of the bonding process are highlighted.Particularly,recent advances and trends in the application of the combination of mechanical interlocking and metallurgical bonding,special energy fields,gradient structure,novel materials,green technology and soft computing method in the roll bonding process are also discussed.The challenges for advancing and prospects of the roll bonding process and bonding model are presented in an attempt to shed some light on the future research direction.

Microstructure and mechanical properties of Mg-5Li-1Al sheets prepared by accumulative roll bonding

Ultrafine-grain and high-strength Mg-SLi-1Al sheets were prepared by accumulative roll bonding （ARB） process. Evolution of microstructure and mechanical properties of ARB-processed Mg-5Li-1Al sheets was investigated. Results show that, during ARB process, the evolution of deformation mechanism oft Mg-5Li-1Al alloy is as follows： twinning deformation, shear deformation, forming macro shear zone, and finally dynamic recrystallization （DRX）. The grain refining mechanism changes from twin DRX to rotation DRX. With the increase in ARB cycles, strength of the Mg-5Li-1Al sheets is enhanced, whilst elongation varies slightly. With the increase in rolling cycles, anisotropy of mechanical properties decreases. It is conclusive that strain hardening and grain refinement dominate the strengthening mechanism of Mg-5Li-1Al alloy.

Effect of annealing on properties of Al/steel composite plates prepared by surface oxidation treatment before cold roll bonding

Al/steel composite plate has a wide application prospect,but great differences in properties between Al and steel are observed.It is difficult to obtain high bonding strength by the traditional cold roll bonding process.Al/steel composite plate was thus prepared by cold roll bonding at a reduction rate of 60%after oxidation treatment on the surface to be composited on the steel side.The heat treatment of holding at 400℃ for 1 h and cooling with the furnace was then adopted.The bonding strength,microstructure,and properties of the Al/steel composite plate before and after annealing were analysed and compared through shear test,bending test,tensile test,and micro-characterization.Results show that the shear strengths of the interface before and after annealing are 100 and 80 MPa,respectively.Although the shear strength of the annealed Al/steel composite plate decreases,the bending and overall tensile properties of the composite plate are improved,showing better mechanical properties.

Al 1060/Pure Iron Clad Materials by Vacuum Roll Bonding and Their Solderability

Al 1060/pure iron clad materials were produced by vacuum roll bonding. The effects of preheating temperature, vacuum roll reduction and initial thickness of the A11060 sheet on the metal interface and bonding strength were investigated. The interfacial microstructure was investigated and the mechanical properties of the joint were evaluated by shear testing. The bonding strength of the clad materials was generally enhanced by increasing the total reduction or preheating temperature, which caused the metal interface to flatten. No obvious reaction or diffusion layer was observed at the interface between Al 1060 and pure iron. The bonding strength increased with decreasing the initial thickness of the Al 1060 sheets. The Al 1060/pure iron clad materials were soldered with Zn-Al alloy by using an ultrasonic-assisted method. Strong bonding of the Al 1060 layer and Al 7N01 was realized without obvious Al 1060 dissolution or effect on the initial interface of Al 1060/pure iron clad materials by soldering at relatively low temperature.

Influence of the Accumulative Roll Bonding Process Severity on the Microstructure and Superplastic Behaviour of 7075 Al Alloy

The 7075 Al alloy was processed by accumulative roll bonding （ARB） at 350 ℃ using 2：1, 3：1 and 4：1 thickness reductions per pass （Rp） up to 8, 6 and 3 passes, respectively. Microstructural examinations of the processed samples revealed that ARB leads to a microstructure composed of equiaxed crystallites with a mean size generally lower than 500 nm. It was found that, due to both the stored energy through- out the processing and the particle pinning effect, the alloy is affected by discontinuous recrystallisation during the inter-pass heating stages, the precise microstructural evolution being dependent on Rp. Me- chanical testing of the ARBed samples revealed that the main active deformation mechanism in the ARBed samples in the temperature range from 250 to 350 ℃ at intermediate and high strain rates is grain bound- ary sliding, the superplastic properties being determined by both the microstructure after ARB and its thermal stability.

Preparation of Aluminum Foam Sandwich by Rolling-bonding/Powder Metallurgy Foaming Technology

Aluminum foam sandwich was prepared by rolling-bonding/powder metallurgical foaming technology, and the effects of rolling on bond strength of face sheet/powders and powder density were studied. Moreover, the foaming agent, TiH2, was heat treated and a certain amount of Mg was added into powder in an attempt to understand how the stability and uniformity of foam was improved. The experimental results show that the foaming precursors with ideal quality were obtained by rolling-bonding process. When rolling reduction is 67%, the consistency of powders reach to 99.87%. Throughout consideration of the bonding of face sheet/ core layer powders and deformation characteristic of powders, the optimum rolling reduction is 60%-70%. Cracks and drainage during foaming were inhibited by heat treatment of foaming agent TiH2 and the addition of a certain amount of Mg. The optimum heat treatment way of TiH2 is that heat preserving 1 hour at 450 ℃; the amount of adding Mg is 1wt%.

Effect of Mechanical Surface Treatment on the Bonding Mechanism and Properties of Cold‑Rolled Cu/Al Clad Plate

In the case of valuable cold-rolled Cu/Al clad plates,billet surface treatment before rolling is a significant process that can affect the bonding efficiency and quality.While the current studies primarily focus on the influence of rolling parameters,insufficient attention has been paid to surface treatment.In this study,the effects of mechanical surface treatment on the bonding mechanism and bonding properties of cold-rolled Cu/Al clad plates were investigated.The results showed that different mechanical surface treatments have significant effects on the surface morphology,roughness,and residual stress.In addition,the effect of surface mechanical treatment on bonding quality was also observed to be critical.When the grinding direction was consistent with the rolling direction(RD),the bonding quality of the Cu/Al clad plates was significantly improved.After surface treatment along the RD for 20 s,the Cu/Al clad plates showed the highest shear strength(78 MPa),approximately four times as high as that of the unpolished samples.Simultaneously,the peel strength of this process was also significantly higher than that achieved via the other processes.Finally,on the basis of the surface morphology,roughness,and residual stress,the effect of surface treatment on the bonding mechanism and bonding properties of Cu/Al clad plates was analyzed.This study proposes a deeper understanding of the bonding behavior and bonding mechanism for cold rolled clad plates processed via mechanical surface treatment.