Mechanical agitation in baffled vessels with turbines plays a vital role in achieving homogeneous fluid mixing and promoting various transfer operations.Therefore,designing vessels with optimal energy efficiency and f...Mechanical agitation in baffled vessels with turbines plays a vital role in achieving homogeneous fluid mixing and promoting various transfer operations.Therefore,designing vessels with optimal energy efficiency and flow dynamics is essential to enhance operational performance and eliminate flow perturbations.Hence,the present research focuses on a numerical investigation of the impact of inclined slots with different angles installed at the side-wall of a cylindrical vessel equipped with a Rushton turbine.This study explores power consumption and vortex size while considering various rotation directions of the impeller with different rotation speeds.The numerical simulations are conducted for Reynolds numbers ranging from 104 to 105,using the RANS k-εturbulence model to govern the flow inside the stirred vessel,accounting for mass and momentum balances.The results have shown that the installation of slots reduces power consumption and vortex size compared to conventional vessel configu-rations.Moreover,increasing the slot angle from 0 to 32.5°further reduces energy consumption and vortex size,especially with negative rotation speeds.On the other hand,increasing the Reynolds numbers leads to a decrease in power consumption and an increase in vortex size.The present research therefore proposes a design for con-structing Rushton-turbine stirred vessels offering optimal operation,characterized by reduced energy consumption and minimized vortex size.展开更多
To restore dam-blocked natural fish migratory passages,a growing number of artificial fishways have been built in water conservancy and hydropower projects in China.The Angu hydropower station involved diverse importa...To restore dam-blocked natural fish migratory passages,a growing number of artificial fishways have been built in water conservancy and hydropower projects in China.The Angu hydropower station involved diverse important fish habitats in the lower reaches of the Daduhe River in Southwest China.Therefore,a vertical slot fishway(VSF)and a nature-like fishway(NLF)were built near the backwater area of the reservoir to connect the upstream and downstream habitats.Hydrodynamic and aquatic ecological surveys were conducted after the completion of the project to estimate the fish passing effect of the two fishways.The results indicated that both fishways were in effective operation and could maintain the desired hydrodynamic conditions and be used by several local fish species.During the survey,149 fish from 15 species and 111 fish from 17 species were captured by the traps in the VSF and NLF,respectively,while 1263 fish from 27 species were found in the downstream area.Some species captured in the VSF were not found in the NLF,and vice versa,which implied the different preferences of fish.Meanwhile,3789 signals including 2099 upward ones and 1690 downward ones were monitored with an ultrasonic fish detector at the inlet of the VSF.These findings revealed the characteristics of fish species observed in and near the fishways and provided valuable insights into the different fish passing capabilities of VSFandNLF.展开更多
Effects of tip slots on the aerodynamic characteristics of helicopter rotor were investigated numerically by solving three-dimensional Navier-Stokes equations based on unstructured overset grids algorithm.Improved del...Effects of tip slots on the aerodynamic characteristics of helicopter rotor were investigated numerically by solving three-dimensional Navier-Stokes equations based on unstructured overset grids algorithm.Improved delayed detached eddy simulation (IDDES) based on the Spalart-Allmaras turbulence model and adaptive grid refinement technique were employed.Several slots in the rotor blade tip were designed on the base of Caradonna-Tung rotor to study the effect of tip slots.Numerical results show that tip slots are able to introduce the airflow from the leading edge and turn it in the spanwise direction to be ejected out of the face at the rotor blade tip,which can reduce the strength of the rotor blade tip vortex and accelerate the dissipation process.Although tip slots may lead to the decrease of airfoils' lift coefficient at the root of the rotor blade,it can increase the lift coefficient of airfoils at the rotor blade tip,so the lift of the rotor with tip slots is almost the same as that of the rotor without tip slots.In addition,tip slots can also reduce the intensity of the tip shock wave,which is beneficial to reduce the wave drag of the rotor.展开更多
The effect of longitudinal-offset radiating slots on a centered-inclined feeding slot in the common broad wall of the two crossed rectangular waveguides is analysed quantitatively. The corresponding equivalent paramet...The effect of longitudinal-offset radiating slots on a centered-inclined feeding slot in the common broad wall of the two crossed rectangular waveguides is analysed quantitatively. The corresponding equivalent parameters are computed by employing the moment method. The numerical results of resonant length of the feeding slot, VSWR and coupling parameter are showed and compared with the case of no radiating slots and short-end. The agreement between theory and experiment is good.展开更多
A numerical investigation of the limit loads is carried out for pressure vessels with part-through slots using a general computational method for the limit analysis of 3-D structures. The limit pressures are given for...A numerical investigation of the limit loads is carried out for pressure vessels with part-through slots using a general computational method for the limit analysis of 3-D structures. The limit pressures are given for a comprehensive range of geometric parameters. Some of the calculated results are compared with the results of 3-D elastic-plastic finite element analysis and existing numerical solutions. The effects of various shapes and sizes of part-through slots on the load carrying capacity of cylindrical shells are investigated and evaluated. Two kinds of typical failure modes corresponding to different dimensions of slots are studied. Based on the numerical results, a geometric parameter G which combines the slot dimensions and the cylinder geometry is presented. It reasonably reflects the overall effect of slots on the limit loads of cylinders. An empirical formula for estimating the limit pressures of cylindrical shells with part-through slots is obtained.展开更多
A three-dimensional finite-element model has been established to investigate the thermal behavior of the medium-thick slab copper casting mold with different cooling water slot designs. The mold wall temperatures meas...A three-dimensional finite-element model has been established to investigate the thermal behavior of the medium-thick slab copper casting mold with different cooling water slot designs. The mold wall temperatures measured using thermocouples buried in different positions of the mold with the original designed cooling system were analyzed to determine the corresponding heat flux profile. This profile was then used for simulation to predict the temperature distribution and the thermal stress distribution of the molds. The predicted temperatures during operation matched the plant measurements. The results showed that the maximum temperature, about 635 K in the wide hot surface, was found about 60 mm below the meniscus and 226 mm from the center of the mold. For the mold with the type I modified design, there was an insignificant decrease in temperature of about 5 K, and for the mold with the type II modified design, the maximum temperature was decreased by about 15 K and the temperature of the hot surface was distributed more uniformly along the length of the mold. The corresponding maximum thermal stress at the hot surface of the mold was reduced from 408 MPa to 386 MPa with the type II modified design. The results indicated that the modified design II is beneficial to the increase of mold life and the quality of casting slabs.展开更多
Numerical analysis is presented for the characteristic parameters of centered-inclined coupling slot in rectangular waveguides, taking into account the transverse distribution of the electric field across the slot ape...Numerical analysis is presented for the characteristic parameters of centered-inclined coupling slot in rectangular waveguides, taking into account the transverse distribution of the electric field across the slot aperture. Integral equations are formulated based on dyadic Green's function theories and solved using the method of moments. Trigonometric basis functions are adopted. It is found that the method will converge with up to ten basis functions. The characteristic parameters can be easily obtained for different slot sizes. Resonant length and resonant resistance of the coupling slots are calculated. It is shown that the calculated results have very high accuracy, compared with simulated results obtained from commercial software. Therefore, it can be effectively applied in the synthesis of antenna arrays. Effects of the transverse distribution on calculating resonant parameters of the coupling slot are also analyzed. The results show that if the transverse distribution of the electric field is neglected, the calculated error tends to become larger when the slot gets wider or thinner.展开更多
Microstrip patch antenna (MPA) is widely implemented in different communication systems. One of the main disadvantages of MPA which limits its applications is its narrow bandwidth. In this paper I enhanced the bandwid...Microstrip patch antenna (MPA) is widely implemented in different communication systems. One of the main disadvantages of MPA which limits its applications is its narrow bandwidth. In this paper I enhanced the bandwidth of MPA by inserting multiple slots in its ground plane. I used FR-4 substrate to design this antenna. The dimensions of this antenna are 59 mm and 79 mm. The dielectric constant is 4.4 and the height is 1.6 mm. I inserted up to 15 slots in ground plane with 1mm width. The spacing between slots is 3 mm. I investigated two designs. In the first design, slots were arranged in parallel to the feeding line. In the second one, slots were arranged horizontally to the feeding line. The main objective of this paper is to design and simulate MPA suitable for wide number of applications. Antenna bandwidth improvement is 18%. All the simulations were obtained by using HFSS simulator.展开更多
This paper studies radiation from circumferential slots on cylindrical waveguide by Poynting’s vector method. It can help us to find mutual admittance between two circumferential slots in an antenna array. The main a...This paper studies radiation from circumferential slots on cylindrical waveguide by Poynting’s vector method. It can help us to find mutual admittance between two circumferential slots in an antenna array. The main advantage of Poynting’s vector method is its accurate convergence to compute mutual admittance between two circumferential slots. The importance of this matter will be more salient while we want to compare it with other mutual admittances and also use it to optimize an antenna array.展开更多
The transverse magnetic (TM) radiation characteristics are investigated for a cylinder with N infinite axial slots of arbitrary opening size and location. The cylinder is a thin circular conductor and coated by an ecc...The transverse magnetic (TM) radiation characteristics are investigated for a cylinder with N infinite axial slots of arbitrary opening size and location. The cylinder is a thin circular conductor and coated by an eccentric material. Fields are found by applying the boundary conditions to the cylindrical wave functions. The addition theorem of Bessel functions is used to obtain an infinite series solution in Fourier–Bessel series form. Results are computed by shrinking the generated infinite series to a finite number of terms and compared to other available data. Numerical results in graphical forms for different values are also developed and discussed for small eccentricities.展开更多
Ultra wide bands antennas with notched bands characteristics have recently been considered for efficient communication between devices. In this paper, a compact ultra-wideband antenna (UWB) for UWB applications with t...Ultra wide bands antennas with notched bands characteristics have recently been considered for efficient communication between devices. In this paper, a compact ultra-wideband antenna (UWB) for UWB applications with triple bandnotched characteristics is presented. The proposed antenna consists of a square patch with four truncated corners and a partial ground plane with a rectangular slit. The operation bandwidth of the designed antenna is from 2.66 GHz to more than 13.5 GHz. Band-notched characteristics of antenna to reject the frequency band of 3.18 - 3.59 GHz and 4.70 - 5.88 GHz, is realized by inserting two C-shaped slots in the patch, the third band of 9.54 - 12.22 GHz is achieved by slottype capacitively-loaded loop (CLL) inserted in the patch near the feed line. Details of the proposed antenna design and simulated results are presented and discussed.展开更多
The design of a seven-band stacked patch antenna for the C, X and Ku band is presented. The antenna consists of an H-slot loaded fed patch, stacked with dual U-slot loaded rectangular patch to generate the seven frequ...The design of a seven-band stacked patch antenna for the C, X and Ku band is presented. The antenna consists of an H-slot loaded fed patch, stacked with dual U-slot loaded rectangular patch to generate the seven frequency bands. The total size of the antenna is 39.25 × 29.25 mm2. The multiband stacked patch antenna is studied and designed using IE3D simulator. For verification of simulation results, the antenna is analyzed by circuit theory concept. The simulated return loss, radiation pattern and gain are presented. Simulated results show that the antenna can be designed to cover the frequency bands from (4.24 GHz to 4.50 GHz, 5.02 GHz to 5.25 GHz) in C-band application, (7.84 GHz to 8.23 GHz) in X-band and (12.16 GHz to 12.35 GHz, 14.25 GHz to 14.76 GHz, 15.25 GHz to 15.51 GHz, 17.52 GHz to 17.86 GHz) in Ku band applications. The bandwidths of each band of the proposed antenna are 5.9%, 4.5%, 4.83%, 2.36%, 3.53%, 1.68% and 1.91%. Similarly the gains of the proposed band are 2.80 dBi, 4.39 dBi, 4.54 dBi, 10.26 dBi, 8.36 dBi and 9.91 dBi, respectively.展开更多
To solve the problems of rock strength increase caused by high in-situ stress,the stress release method with rock slot in the bottom hole by an ultra-high-pressure water jet is proposed.The stress conditions of bottom...To solve the problems of rock strength increase caused by high in-situ stress,the stress release method with rock slot in the bottom hole by an ultra-high-pressure water jet is proposed.The stress conditions of bottom hole rock,before and after slotting are analyzed and the stress release mechanism of slotting is clarified.The results show that the stress release by slotting is due to the coupling of three factors:the relief of horizontal stress,the stress concentration zone distancing away from the cutting face,and the increase of pore pressure caused by rock mass expansion;The stress concentration increases the effective stress of rock along the radial distance from O.6R to 1R(R is the radius of the well),and the presence of groove completely releases the stress,it also allows the stress concentration zone to be pushed away from the cutting face,while significantly lowering the value of stresses in the area the drilling bit acting,the maximum stress release efficiency can reach 80%.The effect of slotting characteristics on release efficiency is obvious when the groove location is near the borehole wall.With the increase of groove depth,the stress release efficiency is significantly increased,and the release range of effective stress is enlarged along the axial direction.Therefore,the stress release method and results of simulations in this paper have a guiding significance for best-improving rock-breaking efficiency and further understanding the technique.展开更多
This paper presents the tri-band slot loaded patch antenna for mobile communication. The antenna consists of parallel slots loaded circular disk with defected ground structure antenna (DGS). The antenna without DGS, a...This paper presents the tri-band slot loaded patch antenna for mobile communication. The antenna consists of parallel slots loaded circular disk with defected ground structure antenna (DGS). The antenna without DGS, acts like wide band antenna and bandwidth is 34.45% (3.47 - 4.92 GHz) with maximum gain of 4.97 dBi, which can be used in WiMax application. This structure has the following advantages: 1) co-axial feeding technique, which is very simple as compared to other feeding technique, 2) simple and cost effective and 3) it is more efficient than the antenna without DGS. This antenna has been analyzed using IE3D simulation software.展开更多
This paper develops a hypersonic aerothermal simulation method for missile slot flow. The finite volume method of structure grid solver is developed for solving Euler and Navier-Stokes equations. The solver includes P...This paper develops a hypersonic aerothermal simulation method for missile slot flow. The finite volume method of structure grid solver is developed for solving Euler and Navier-Stokes equations. The solver includes Park's two temperature model and the air multi-species reaction model. The second-order accuracy TVD numerical method was deduced to compute the hypersonic aeroheating which improves the computational efficiency. Computational results are given to show the high accuracy comparing to the existing experimental data.展开更多
Dear Editor, This letter deals with the joint slot scheduling and power allocation in clustered underwater acoustic sensor networks(UASNs),based on the known clustering and routing information, to maximize the network...Dear Editor, This letter deals with the joint slot scheduling and power allocation in clustered underwater acoustic sensor networks(UASNs),based on the known clustering and routing information, to maximize the network's energy efficiency(EE). Based on the block coordinated decent(BCD) method, the formulated mixed-integer non-convex problem is alternatively optimized by leveraging the KuhnMunkres algorithm.展开更多
Damage is one of the most important characteristics of rock failure.Studying the damage mechanism of rock blasting under the guiding effect of the water jet slot and revealing the mechanism of controlled blasting with...Damage is one of the most important characteristics of rock failure.Studying the damage mechanism of rock blasting under the guiding effect of the water jet slot and revealing the mechanism of controlled blasting with water jet assistance are crucial.In this study,a rock-like material was chosen as the research object for the calibration experiment of the numerical model.The numerical simulation models were then established by ANSYS/LS-DYNA,and the blastinduced damage mechanism under the guiding effect of the water jet slot was analyzed according to the blasting theory.The results indicated that explosive energy accumulates toward the direction of the slot as the guiding effect of the water jet slot,which allows the rock mass in the direction of the slot bear more damage.Meanwhile,the rock mass in the middle of the connection line between two blast-holes bears more damage under the combination of the effect of the explosion stress wave and guiding effect of water the jet slot on the detonation gas during double-slotted borehole blasting,which results in the formation of a gourd-shaped blast-induced damage area.In addition,the influence of the water jet slot on blast-induced damage varies depending on the blasting-process stage.展开更多
The rapid advancement of Internet of Things(IoT)technology has brought convenience to people’s lives;however further development of IoT faces serious challenges,such as limited energy and shortage of network spectrum...The rapid advancement of Internet of Things(IoT)technology has brought convenience to people’s lives;however further development of IoT faces serious challenges,such as limited energy and shortage of network spectrum resources.To address the above challenges,this study proposes a simultaneous wireless information and power transfer IoT adaptive time slot resource allocation(SIATS)algorithm.First,an adaptive time slot consisting of periods for sensing,information transmission,and energy harvesting is designed to ensure that the minimum energy harvesting requirement ismet while the maximumuplink and downlink throughputs are obtained.Second,the optimal transmit power and channel assignment of the system are obtained using the Lagrangian dual and gradient descent methods,and the optimal time slot assignment is determined for each IoT device such that the sum of the throughput of all devices is maximized.Simulation results show that the SIATS algorithm performs satisfactorily and provides an increase in the throughput by up to 14.4%compared with that of the fixed time slot allocation(FTS)algorithm.In the case of a large noise variance,the SIATS algorithm has good noise immunity,and the total throughput of the IoT devices obtained using the SIATS algorithm can be improved by up to 34.7%compared with that obtained using the FTS algorithm.展开更多
In order to improve the operation efficiency of coaxial magnetic gear(CMG),in this paper,a CMG model with slotted in magnetic modulation ring is proposed.In this model,the permanent magnets(PMs)of internal and externa...In order to improve the operation efficiency of coaxial magnetic gear(CMG),in this paper,a CMG model with slotted in magnetic modulation ring is proposed.In this model,the permanent magnets(PMs)of internal and external rotors are distributed in Halbach array,the inner rotor PMs are equally divided into 3 small pieces,and the outer rotor PMs are equally divided into 2 small pieces.At the same time,the static magnetic modulation ring iron blocks are slotted,each iron block has 3 slots,the width of the slot is 0.4°,and the depth of the single side slot is 1mm.Finally,a two-dimensional model is established,and the eddy current loss and iron loss of the model are optimized,compared with the conventional CMG model,it is found that the changed pattern can increase the internal and external output torque by 4%and 4.12%,respectively.The eddy current loss is reduced by 66.57%,and the iron loss is reduced by 8.9%,which significantly improve the operation efficiency of the CMG.展开更多
文摘Mechanical agitation in baffled vessels with turbines plays a vital role in achieving homogeneous fluid mixing and promoting various transfer operations.Therefore,designing vessels with optimal energy efficiency and flow dynamics is essential to enhance operational performance and eliminate flow perturbations.Hence,the present research focuses on a numerical investigation of the impact of inclined slots with different angles installed at the side-wall of a cylindrical vessel equipped with a Rushton turbine.This study explores power consumption and vortex size while considering various rotation directions of the impeller with different rotation speeds.The numerical simulations are conducted for Reynolds numbers ranging from 104 to 105,using the RANS k-εturbulence model to govern the flow inside the stirred vessel,accounting for mass and momentum balances.The results have shown that the installation of slots reduces power consumption and vortex size compared to conventional vessel configu-rations.Moreover,increasing the slot angle from 0 to 32.5°further reduces energy consumption and vortex size,especially with negative rotation speeds.On the other hand,increasing the Reynolds numbers leads to a decrease in power consumption and an increase in vortex size.The present research therefore proposes a design for con-structing Rushton-turbine stirred vessels offering optimal operation,characterized by reduced energy consumption and minimized vortex size.
基金supported by the National Outstanding Youth Science Fund Project of the National Natural Science Foundation of China(Grant No.51922065)the National Natural Science Foundation of China(Grant No.52179070)the Open Research Fund of Hubei International Science and Technology Cooperation Base of Fish Passage(Grant No.HIBF2020007).
文摘To restore dam-blocked natural fish migratory passages,a growing number of artificial fishways have been built in water conservancy and hydropower projects in China.The Angu hydropower station involved diverse important fish habitats in the lower reaches of the Daduhe River in Southwest China.Therefore,a vertical slot fishway(VSF)and a nature-like fishway(NLF)were built near the backwater area of the reservoir to connect the upstream and downstream habitats.Hydrodynamic and aquatic ecological surveys were conducted after the completion of the project to estimate the fish passing effect of the two fishways.The results indicated that both fishways were in effective operation and could maintain the desired hydrodynamic conditions and be used by several local fish species.During the survey,149 fish from 15 species and 111 fish from 17 species were captured by the traps in the VSF and NLF,respectively,while 1263 fish from 27 species were found in the downstream area.Some species captured in the VSF were not found in the NLF,and vice versa,which implied the different preferences of fish.Meanwhile,3789 signals including 2099 upward ones and 1690 downward ones were monitored with an ultrasonic fish detector at the inlet of the VSF.These findings revealed the characteristics of fish species observed in and near the fishways and provided valuable insights into the different fish passing capabilities of VSFandNLF.
基金supported by the Natural Science Foundation of Fujian Province of China(No.2016J01029)the Aeronautical Science Foundation of China(No.20155768007)the National Natural Science Foundation of China(No.11602209)
文摘Effects of tip slots on the aerodynamic characteristics of helicopter rotor were investigated numerically by solving three-dimensional Navier-Stokes equations based on unstructured overset grids algorithm.Improved delayed detached eddy simulation (IDDES) based on the Spalart-Allmaras turbulence model and adaptive grid refinement technique were employed.Several slots in the rotor blade tip were designed on the base of Caradonna-Tung rotor to study the effect of tip slots.Numerical results show that tip slots are able to introduce the airflow from the leading edge and turn it in the spanwise direction to be ejected out of the face at the rotor blade tip,which can reduce the strength of the rotor blade tip vortex and accelerate the dissipation process.Although tip slots may lead to the decrease of airfoils' lift coefficient at the root of the rotor blade,it can increase the lift coefficient of airfoils at the rotor blade tip,so the lift of the rotor with tip slots is almost the same as that of the rotor without tip slots.In addition,tip slots can also reduce the intensity of the tip shock wave,which is beneficial to reduce the wave drag of the rotor.
文摘The effect of longitudinal-offset radiating slots on a centered-inclined feeding slot in the common broad wall of the two crossed rectangular waveguides is analysed quantitatively. The corresponding equivalent parameters are computed by employing the moment method. The numerical results of resonant length of the feeding slot, VSWR and coupling parameter are showed and compared with the case of no radiating slots and short-end. The agreement between theory and experiment is good.
文摘A numerical investigation of the limit loads is carried out for pressure vessels with part-through slots using a general computational method for the limit analysis of 3-D structures. The limit pressures are given for a comprehensive range of geometric parameters. Some of the calculated results are compared with the results of 3-D elastic-plastic finite element analysis and existing numerical solutions. The effects of various shapes and sizes of part-through slots on the load carrying capacity of cylindrical shells are investigated and evaluated. Two kinds of typical failure modes corresponding to different dimensions of slots are studied. Based on the numerical results, a geometric parameter G which combines the slot dimensions and the cylinder geometry is presented. It reasonably reflects the overall effect of slots on the limit loads of cylinders. An empirical formula for estimating the limit pressures of cylindrical shells with part-through slots is obtained.
基金financially supported by the National Natural Science Foundation of China(Nos.51525401,51274054,U1332115,51401044)the Science and Technology Planning Project of Dalian(No.2013A16GX110)+1 种基金the China Postdoctoral Science Foundation(2015M581331)the Fundamental Research Funds for the Central Universities
文摘A three-dimensional finite-element model has been established to investigate the thermal behavior of the medium-thick slab copper casting mold with different cooling water slot designs. The mold wall temperatures measured using thermocouples buried in different positions of the mold with the original designed cooling system were analyzed to determine the corresponding heat flux profile. This profile was then used for simulation to predict the temperature distribution and the thermal stress distribution of the molds. The predicted temperatures during operation matched the plant measurements. The results showed that the maximum temperature, about 635 K in the wide hot surface, was found about 60 mm below the meniscus and 226 mm from the center of the mold. For the mold with the type I modified design, there was an insignificant decrease in temperature of about 5 K, and for the mold with the type II modified design, the maximum temperature was decreased by about 15 K and the temperature of the hot surface was distributed more uniformly along the length of the mold. The corresponding maximum thermal stress at the hot surface of the mold was reduced from 408 MPa to 386 MPa with the type II modified design. The results indicated that the modified design II is beneficial to the increase of mold life and the quality of casting slabs.
文摘Numerical analysis is presented for the characteristic parameters of centered-inclined coupling slot in rectangular waveguides, taking into account the transverse distribution of the electric field across the slot aperture. Integral equations are formulated based on dyadic Green's function theories and solved using the method of moments. Trigonometric basis functions are adopted. It is found that the method will converge with up to ten basis functions. The characteristic parameters can be easily obtained for different slot sizes. Resonant length and resonant resistance of the coupling slots are calculated. It is shown that the calculated results have very high accuracy, compared with simulated results obtained from commercial software. Therefore, it can be effectively applied in the synthesis of antenna arrays. Effects of the transverse distribution on calculating resonant parameters of the coupling slot are also analyzed. The results show that if the transverse distribution of the electric field is neglected, the calculated error tends to become larger when the slot gets wider or thinner.
文摘Microstrip patch antenna (MPA) is widely implemented in different communication systems. One of the main disadvantages of MPA which limits its applications is its narrow bandwidth. In this paper I enhanced the bandwidth of MPA by inserting multiple slots in its ground plane. I used FR-4 substrate to design this antenna. The dimensions of this antenna are 59 mm and 79 mm. The dielectric constant is 4.4 and the height is 1.6 mm. I inserted up to 15 slots in ground plane with 1mm width. The spacing between slots is 3 mm. I investigated two designs. In the first design, slots were arranged in parallel to the feeding line. In the second one, slots were arranged horizontally to the feeding line. The main objective of this paper is to design and simulate MPA suitable for wide number of applications. Antenna bandwidth improvement is 18%. All the simulations were obtained by using HFSS simulator.
文摘This paper studies radiation from circumferential slots on cylindrical waveguide by Poynting’s vector method. It can help us to find mutual admittance between two circumferential slots in an antenna array. The main advantage of Poynting’s vector method is its accurate convergence to compute mutual admittance between two circumferential slots. The importance of this matter will be more salient while we want to compare it with other mutual admittances and also use it to optimize an antenna array.
文摘The transverse magnetic (TM) radiation characteristics are investigated for a cylinder with N infinite axial slots of arbitrary opening size and location. The cylinder is a thin circular conductor and coated by an eccentric material. Fields are found by applying the boundary conditions to the cylindrical wave functions. The addition theorem of Bessel functions is used to obtain an infinite series solution in Fourier–Bessel series form. Results are computed by shrinking the generated infinite series to a finite number of terms and compared to other available data. Numerical results in graphical forms for different values are also developed and discussed for small eccentricities.
文摘Ultra wide bands antennas with notched bands characteristics have recently been considered for efficient communication between devices. In this paper, a compact ultra-wideband antenna (UWB) for UWB applications with triple bandnotched characteristics is presented. The proposed antenna consists of a square patch with four truncated corners and a partial ground plane with a rectangular slit. The operation bandwidth of the designed antenna is from 2.66 GHz to more than 13.5 GHz. Band-notched characteristics of antenna to reject the frequency band of 3.18 - 3.59 GHz and 4.70 - 5.88 GHz, is realized by inserting two C-shaped slots in the patch, the third band of 9.54 - 12.22 GHz is achieved by slottype capacitively-loaded loop (CLL) inserted in the patch near the feed line. Details of the proposed antenna design and simulated results are presented and discussed.
文摘The design of a seven-band stacked patch antenna for the C, X and Ku band is presented. The antenna consists of an H-slot loaded fed patch, stacked with dual U-slot loaded rectangular patch to generate the seven frequency bands. The total size of the antenna is 39.25 × 29.25 mm2. The multiband stacked patch antenna is studied and designed using IE3D simulator. For verification of simulation results, the antenna is analyzed by circuit theory concept. The simulated return loss, radiation pattern and gain are presented. Simulated results show that the antenna can be designed to cover the frequency bands from (4.24 GHz to 4.50 GHz, 5.02 GHz to 5.25 GHz) in C-band application, (7.84 GHz to 8.23 GHz) in X-band and (12.16 GHz to 12.35 GHz, 14.25 GHz to 14.76 GHz, 15.25 GHz to 15.51 GHz, 17.52 GHz to 17.86 GHz) in Ku band applications. The bandwidths of each band of the proposed antenna are 5.9%, 4.5%, 4.83%, 2.36%, 3.53%, 1.68% and 1.91%. Similarly the gains of the proposed band are 2.80 dBi, 4.39 dBi, 4.54 dBi, 10.26 dBi, 8.36 dBi and 9.91 dBi, respectively.
基金support of the National Key Research and Development Program of China(2021YFE0111400)the Shandong provincial natural science foundation(No.ZR2019MEE120)the horizon programme of the EU's funding of the ORCH YD project,EU-H2020(101006752-ORCHYD).
文摘To solve the problems of rock strength increase caused by high in-situ stress,the stress release method with rock slot in the bottom hole by an ultra-high-pressure water jet is proposed.The stress conditions of bottom hole rock,before and after slotting are analyzed and the stress release mechanism of slotting is clarified.The results show that the stress release by slotting is due to the coupling of three factors:the relief of horizontal stress,the stress concentration zone distancing away from the cutting face,and the increase of pore pressure caused by rock mass expansion;The stress concentration increases the effective stress of rock along the radial distance from O.6R to 1R(R is the radius of the well),and the presence of groove completely releases the stress,it also allows the stress concentration zone to be pushed away from the cutting face,while significantly lowering the value of stresses in the area the drilling bit acting,the maximum stress release efficiency can reach 80%.The effect of slotting characteristics on release efficiency is obvious when the groove location is near the borehole wall.With the increase of groove depth,the stress release efficiency is significantly increased,and the release range of effective stress is enlarged along the axial direction.Therefore,the stress release method and results of simulations in this paper have a guiding significance for best-improving rock-breaking efficiency and further understanding the technique.
文摘This paper presents the tri-band slot loaded patch antenna for mobile communication. The antenna consists of parallel slots loaded circular disk with defected ground structure antenna (DGS). The antenna without DGS, acts like wide band antenna and bandwidth is 34.45% (3.47 - 4.92 GHz) with maximum gain of 4.97 dBi, which can be used in WiMax application. This structure has the following advantages: 1) co-axial feeding technique, which is very simple as compared to other feeding technique, 2) simple and cost effective and 3) it is more efficient than the antenna without DGS. This antenna has been analyzed using IE3D simulation software.
基金supported by the National Natural Science Foundation of China(10872050)the Fundamental Research Funds for the Centred Universities (DUT11ZD(G)01)
文摘This paper develops a hypersonic aerothermal simulation method for missile slot flow. The finite volume method of structure grid solver is developed for solving Euler and Navier-Stokes equations. The solver includes Park's two temperature model and the air multi-species reaction model. The second-order accuracy TVD numerical method was deduced to compute the hypersonic aeroheating which improves the computational efficiency. Computational results are given to show the high accuracy comparing to the existing experimental data.
基金supported by the National Natural Science Foundation of China(62273298,61873223)the Natural Science Foundation of Hebei Province(F2019203095)Provincial Key Laboratory Performance Subsidy Project(22567612H)。
文摘Dear Editor, This letter deals with the joint slot scheduling and power allocation in clustered underwater acoustic sensor networks(UASNs),based on the known clustering and routing information, to maximize the network's energy efficiency(EE). Based on the block coordinated decent(BCD) method, the formulated mixed-integer non-convex problem is alternatively optimized by leveraging the KuhnMunkres algorithm.
基金support for this work was provided by the Sichuan Natural Science Foundation Project(Youth Science Foundation Project)(No.2022NSFSC1089)the Natural Science Foundation of Southwest University of Science and Technology(No.18zx7124).
文摘Damage is one of the most important characteristics of rock failure.Studying the damage mechanism of rock blasting under the guiding effect of the water jet slot and revealing the mechanism of controlled blasting with water jet assistance are crucial.In this study,a rock-like material was chosen as the research object for the calibration experiment of the numerical model.The numerical simulation models were then established by ANSYS/LS-DYNA,and the blastinduced damage mechanism under the guiding effect of the water jet slot was analyzed according to the blasting theory.The results indicated that explosive energy accumulates toward the direction of the slot as the guiding effect of the water jet slot,which allows the rock mass in the direction of the slot bear more damage.Meanwhile,the rock mass in the middle of the connection line between two blast-holes bears more damage under the combination of the effect of the explosion stress wave and guiding effect of water the jet slot on the detonation gas during double-slotted borehole blasting,which results in the formation of a gourd-shaped blast-induced damage area.In addition,the influence of the water jet slot on blast-induced damage varies depending on the blasting-process stage.
基金supported in part by Sub Project of National Key Research and Development Plan in 2020.No.2020YFC1511704Beijing Information Science&Technology University.Nos.2020KYNH212,2021CGZH302+1 种基金Beijing Science and Technology Project(Grant No.Z211100004421009)in part by the National Natural Science Foundation of China(Grant No.61971048).
文摘The rapid advancement of Internet of Things(IoT)technology has brought convenience to people’s lives;however further development of IoT faces serious challenges,such as limited energy and shortage of network spectrum resources.To address the above challenges,this study proposes a simultaneous wireless information and power transfer IoT adaptive time slot resource allocation(SIATS)algorithm.First,an adaptive time slot consisting of periods for sensing,information transmission,and energy harvesting is designed to ensure that the minimum energy harvesting requirement ismet while the maximumuplink and downlink throughputs are obtained.Second,the optimal transmit power and channel assignment of the system are obtained using the Lagrangian dual and gradient descent methods,and the optimal time slot assignment is determined for each IoT device such that the sum of the throughput of all devices is maximized.Simulation results show that the SIATS algorithm performs satisfactorily and provides an increase in the throughput by up to 14.4%compared with that of the fixed time slot allocation(FTS)algorithm.In the case of a large noise variance,the SIATS algorithm has good noise immunity,and the total throughput of the IoT devices obtained using the SIATS algorithm can be improved by up to 34.7%compared with that obtained using the FTS algorithm.
基金supported in part by National Natural Science Foundation of China and China Postdoctoral Science Foundation.(Project No.51707072,2018M632855).
文摘In order to improve the operation efficiency of coaxial magnetic gear(CMG),in this paper,a CMG model with slotted in magnetic modulation ring is proposed.In this model,the permanent magnets(PMs)of internal and external rotors are distributed in Halbach array,the inner rotor PMs are equally divided into 3 small pieces,and the outer rotor PMs are equally divided into 2 small pieces.At the same time,the static magnetic modulation ring iron blocks are slotted,each iron block has 3 slots,the width of the slot is 0.4°,and the depth of the single side slot is 1mm.Finally,a two-dimensional model is established,and the eddy current loss and iron loss of the model are optimized,compared with the conventional CMG model,it is found that the changed pattern can increase the internal and external output torque by 4%and 4.12%,respectively.The eddy current loss is reduced by 66.57%,and the iron loss is reduced by 8.9%,which significantly improve the operation efficiency of the CMG.