A Ventral Diverterless High Offset S-shaped Inlet at Transonic Speeds

An investigation on the ventral diverterless high offset S-shaped inlet is carried out at Mach numbers from 0.600 to 1.534, angles of attack from -4° to 9.4°, and yaw angles from 0° to 8°. Results indicate： （1） a large region of low total pressure exists at the lower part of the inlet exit caused by the counter-rotating vortices in the S-shaped duct; （2） the performances of the inlet at Mach number 1.000 reach almost the highest, so the propulsion system could work efficiently in terms of aerodynamics; （3） the total pressure recovery increases slowly at first and then remains unvaried as the Mach number rises from 0.6 to 1.0, however, it does in an opposite manner in the conventional diverter-equipped S-shaped inlet; （4） the performances of the inlet are generally insensitive to angles of attack from -4° to 9.4° and yaw angles from 0° to 8° at Mach number 0.850, and angles of attack from -2° to 6° and yaw angles from 0° to 5° at Mach number 1.534.

Numerical Investigation of Electrohydrodynamic (EHD) Flow Control in an S-Shaped Duct

An electrohydrodynamic （EHD） method, which is based on glow discharge plasma, is presented for flow control in an S-shaped duct. The research subject is an expanding channel with a constant width and a rectangular cross section. An equivalent divergence angle and basic function are introduced to build the three-dimensional model. Subsequently, the plasma physical models are simplified as the effects of electrical body force and work （done by the force） on the fluid near the wall. With the aid of FLUENT software, the source terms of momentum and energy are added to the Navier-Stokes equation. Finally, the original performance of three models （A, B and C） is studied, in which model A demonstrates better performance. Then EHD control based on model A is discussed. The results show that the EHD method is an effective way of reducing flow loss and improving uniformity at the duct exit. The innovation in this study is the assessment of the EHD control effect on the flow in an S-shaped duct. Both the parametric modeling of the S-shaped duct and the simplified models of plasma provide valuable information for future research on aircraft inlet ducts.

Incorporating S-shaped testing-effort functions into NHPP software reliability model with imperfect debugging

Testing-effort（TE） and imperfect debugging（ID） in the reliability modeling process may further improve the fitting and prediction results of software reliability growth models（SRGMs）. For describing the S-shaped varying trend of TE increasing rate more accurately, first, two S-shaped testing-effort functions（TEFs）, i.e.,delayed S-shaped TEF（DS-TEF） and inflected S-shaped TEF（IS-TEF）, are proposed. Then these two TEFs are incorporated into various types（exponential-type, delayed S-shaped and inflected S-shaped） of non-homogeneous Poisson process（NHPP）SRGMs with two forms of ID respectively for obtaining a series of new NHPP SRGMs which consider S-shaped TEFs as well as ID. Finally these new SRGMs and several comparison NHPP SRGMs are applied into four real failure data-sets respectively for investigating the fitting and prediction power of these new SRGMs.The experimental results show that：（i） the proposed IS-TEF is more suitable and flexible for describing the consumption of TE than the previous TEFs;（ii） incorporating TEFs into the inflected S-shaped NHPP SRGM may be more effective and appropriate compared with the exponential-type and the delayed S-shaped NHPP SRGMs;（iii） the inflected S-shaped NHPP SRGM considering both IS-TEF and ID yields the most accurate fitting and prediction results than the other comparison NHPP SRGMs.

Modeling behaviors of a coal pillar rib using the progressive S-shaped yield criterion

Spalling of pillar ribs has been a major hazard in the mining industry for decades.In the absence of rib support guidelines,accidents have continued to occur in recent years.Developing effective support guidelines requires a complete understanding of complex pillar damage mechanisms.Continuum models represent a convenient tool for analyzing this problem,but the behavior of such models is dependent of the choice of the constitutive model.In this study,a recently proposed constitutive model was used to simulate the rib fracturing process in a longwall chain pillar at West Cliff mine.After calibration,the model was able to capture the rib displacement profiles for multiple locations of the longwall face and the stress evolution 4 m into the pillar.The rib bolts in the model were found to be yielding over 60% of their length under the headgate loading condition.The model also predicted a steady damage accumulation in the rib for certain face locations,which is consistent with the description of the rib at the site.Damage was localized along the upper part of the pillar and underscored the role that the dirt band played in controlling rib deterioration at the site.The ability of the numerical model to replicate field measurements provides confidence in the capabilities of the new constitutive model.Finally,the need of using multi-point calibration is highlighted by comparing the results of the calibrated model to an alternative model calibrated to a smaller amount of data.

Analysis and Simulation of S-shaped Waveguide in Silicon-on-insulator

The simulation and analysis of S-shaped waveguide bend are presented.Bend radius larger than 30 mm assures less than 0.5 dB radiation loss for a 4-μm-wide silicon-on-insulator waveguide bend with 2-μm etch depth.Intersection angle greater than 20° provides negligible crosstalk (<-30 dB) and very low insertion loss.Any reduction in bend radius and intersection angle is at the cost of the degradation of characteristics of bent waveguide and intersecting waveguide, respectively.

Enhancement of Characteristics of Antenna Arrays Employing S-Shaped Resonators

This paper illustrates a simple kind of tri-band printed G-shaped monopole antenna for Multiple-Input-Multiple-Output (MIMO) systems. The proposed antenna is used to achieve three operating frequencies, 2.45 GHz, 5.2 GHz and 8.2 GHz for wireless communications. To improve the isolation between the two radiating elements, we use left-handed materials composed of only S-shaped resonators to get negative refractive index at the three operating frequencies. When one layer of S-shaped resonators is employed, the antenna correlation, the diversity gain and the bandwidth are also enhanced. The simulated results are presented and evaluated with and without left-handed materials.

Shaping ability of thermomechanically treated files in simulated S-shaped root canals

Aim: the aim of this study was to investigate the shaping ability of thermomechanically treated files manufactured by twisting(Twisted files)and compare it to conventional rotary system (K3, Sybron Endo, Orange, CA) in S-shaped canals, including formation of ledges, zipping, elbow, outer widening, danger zone, perforation and file deformation. Materials & Methods: Forty S-Shaped canals in resin blocks were randomly divided into 2 groups of 20 each. Pre-instrumentation images of the canals were taken via a digital camera and superimposed on images taken after preparation with TF and K3 systems to apical size of 25/06 and 30/06. Canal aberrations were measured from the superimposed image at five levels using AutoCAD system. Fisher exact test and Mann Whitney test were used for analysis of the data. Results: the incidence of zipping, elbow and apical transportation was significantly lower in the TF group (P = 0.04). Generally the incidence of aberration increased when the apical size increased to 30/0.06 regardless of the file system. Significant file deformation was evident in the TF after single use (P ? 0.001). Conclusion: Under the conditions of this study, TF manufactured by new technique performed better than K3 systems when used up to size 25/06 in simulated S-shaped canals. Clinical significance: The flexibility of thermomechanically treated files is beneficial in canals with multiple curvatures;however, attention should be paid to the instrument taper and final apical size of the preparation.

Analysis of the generation mechanism of the S-shaped J–V curves of MoS_(2)/Si-based solar cells

Amorphous–microcrystalline MoS_(2)thin films are fabricated using the sol-gel method to produce MoS_(2)/Si-based solar cells. The generation mechanisms of the S-shaped current density–voltage(J–V) curves of the solar cells are analyzed. To improve the performance of the solar cells and address the problem of the S-shaped J–V curve, a MoS_(2)film and a p^(+) layer are introduced into the front and back interfaces of the solar cell, respectively, which leads to the formation of a p–n junction between the p-Si and the MoS_(2)film as well as ohmic contacts between the MoS_(2)film and the ITO, improving the S-shaped J–V curve. As a result of the high doping characteristics and the high work function of the p^(+) layer, a high–low junction is formed between the p;and p layers along with ohmic contacts between the p;layer and the Ag electrode. Consequently,the S-shaped J–V curve is eliminated, and a significantly higher current density is achieved at a high voltage. The device exhibits ideal p–n junction rectification characteristics and achieves a high power-conversion efficiency(CE) of 7.55%. The findings of this study may improve the application of MoS_(2)thin films in silicon-based solar cells, which are expected to be widely used in various silicon-based electronic and optical devices.

Bird specimen number linked with species trait and climate niche breadth

Biological specimens are fundamental for taxonomy and flora/fauna research.More importantly,they also play crucial roles in recording environmental impacts on morphology and behavior,which is vital for biodiversity research and conservation.However,there are few systematic studies on the patterns and drivers of bird specimen number at regional scales.This study is the first attempt to examine the relationships between bird specimen number and species traits as well as climate niche breadth in China,aiming to answer two questions:1)how do species’temperature niche breadth and precipitation niche breadth influence specimen number?2)which trait is most associated with bird specimen number?The associations between bird specimen number and explanatory variables were examined using ordinary least squares,generalized linear models,phylogenetic generalized linear mixed models,and multiple comparisons.The results showed that Muscicapidae was the family with the highest specimen number,and Passeriformes was the order with the highest specimen number.Bird specimen number significantly increased with larger temperature niche breadth and precipitation niche breadth.Specimen number was also positively associated with geographic range size,habitat specificity,hunting vulnerability and clutch size,but negatively associated with body size.These findings suggest that future bird specimen collection should pay more attention to birds with limited ecological niches,large body sizes,and small clutch sizes.This research enhances the use of bird specimen data to study and preserve biodiversity.

Dynamic characteristics of coal specimens with varying static preloading levels under low-frequency disturbance load

The mechanical properties of residual coal pillars under the influence of upward mining disturbances significantly affect the safety of residual mining activities on working faces.This study conducted low-frequency disturbance dynamic uniaxial compression tests on coal specimens using a self-developed dynamic-static load coupling electro-hydraulic servo system,and studied the strength evolutions,surface deformations,acoustic emission(AE)characteristic parameters,and the failure modes of coal specimens with different static preloading levels were studied.The disturbance damage is positively correlated with the coal specimen static preload level.Specifically,the cumulative AE count rates of the initial accelerated damage stage for the coal specimens with static preloading level of 60%and 70%of the uniaxial compressive strength(UCS)were 2.66 and 3.19 times that of the 50%UCS specimens,respectively.Macroscopically,this behaviour manifested as a decrease in the compressive strength,and the mean strengths of the disturbance-damaged coal specimens with 60%and 70%of UCS static preloading decreased by 8.53%and 9.32%,respectively,compared to those of the specimens under pure static loading.The crack sources,such as the primary fissures,strongly control the dynamic response of the coal specimen.The difference between the dynamic responses of the coal specimens and that of dense rocks is significant.

Species’ geographical range, environmental range and traits lead to specimen collection preference of dominant plant species of grasslands in Northern China

Many different factors,such as species traits,socio-economic factors,geographical and environmental factors,can lead to specimen collection preference.This study aims to determine whether grassland specimen collection in China is preferred by species traits(i.e.,plant height,flowering and fruiting period),environmental range(i.e.,the temperature and precipitation range)and geographical range(i.e.,distribution range and altitudinal range).Ordinary least squares models and phylogenetic generalized linear mixed models were used to analyze the relationships between specimen number and the explanatory variables.Random Forest models were then used to find the most parsimonious multivariate model.The results showed that interannual variation in specimen number between 1900 and 2020 was considerable.Specimen number of these species in southeast China was notably lower than that in northwest China.Environmental range and geographical range of species had significant positive correlations with specimen number.In addition,there were relatively weak but significant associations between specimen number and species trait(i.e.,plant height and flowering and fruiting period).Random Forest models indicated that distribution range was the most important variable,followed by flowering and fruiting period,and altitudinal range.These findings suggest that future floristic surveys should pay more attention to species with small geographical range,narrow environmental range,short plant height,and short flowering and fruiting period.The correction of specimen collection preference will also make the results of species distribution model,species evolution and other works based on specimen data more accurate.

Direct Pointwise Comparison of FE Predictions to StereoDIC Measurements:Developments and Validation Using Double Edge-Notched Tensile Specimen

To compare finite element analysis(FEA)predictions and stereovision digital image correlation(StereoDIC)strain measurements at the same spatial positions throughout a region of interest,a field comparison procedure is developed.The procedure includes(a)conversion of the finite element data into a triangular mesh,(b)selection of a common coordinate system,(c)determination of the rigid body transformation to place both measurements and FEA data in the same system and(d)interpolation of the FEA nodal information to the same spatial locations as the StereoDIC measurements using barycentric coordinates.For an aluminum Al-6061 double edge notched tensile specimen,FEA results are obtained using both the von Mises isotropic yield criterion and Hill’s quadratic anisotropic yield criterion,with the unknown Hill model parameters determined using full-field specimen strain measurements for the nominally plane stress specimen.Using Hill’s quadratic anisotropic yield criterion,the point-by-point comparison of experimentally based full-field strains and stresses to finite element predictions are shown to be in excellent agreement,confirming the effectiveness of the field comparison process.

Perioperative outcomes of transvaginal specimen extraction laparoscopic total gastrectomy and conventional laparoscopicassisted total gastrectomy

BACKGROUND Natural orifice specimen extraction surgery(NOSES)has emerged as a promising alternative compared to conventional laparoscopic-assisted total gastrectomy(LATG)for treating gastric cancer(GC).However,evidence regarding the efficacy and safety of NOSES for GC surgery is limited.This study aimed to compare the safety and feasibility,in addition to postoperative complications of NOSES and LATG.METHODS Dual circular staplers were used in Roux-en-Y digestive tract reconstruction for transvaginal specimen extraction LATG,and its outcomes were compared with LATG in a cohort of 51 GC patients with tumor size≤5 cm.The study was conducted from May 2018 to September 2020,and patients were categorized into the NOSES group(n=22)and LATG group(n=29).Perioperative parameters were compared and analyzed,including patient and tumor characteristics,postoperative outcomes,and anastomosis-related complications,postoperative hospital stay,the length of abdominal incision,difference in tumor type,postoperative complications,and postoperative survival.RESULTS Postoperative exhaust time,operation duration,mean postoperative hospital stay,length of abdominal incision,number of specific staplers used,and Brief Illness Perception Questionnaire score were significant in both groups(P<0.01).In the NOSES group,the postoperative time to first flatus,mean postoperative hospital stay,and length of abdominal incision were significantly shorter than those in the LATG group.Patients in the NOSES group had faster postoperative recovery,and achieved abdominal minimally invasive incision that met aesthetic requirements.There were no significant differences in gender,age,tumor type,postoperative complications,and postoperative survival between the two groups.CONCLUSION The application of dual circular staplers in Roux-en-Y digestive tract reconstruction combined with NOSES gastrectomy is safe and convenient.This approach offers better short-term outcomes compared to LATG,while long-term survival rates are comparable to those of conventional laparoscopic surgery.

Research on rock hand specimen naming method based on deep learning and Inception-v3 model

The naming of rock hand specimens is usually conducted by geological workers based on observed mineral composition,texture characteristics,etc.,combined with their own knowledge reserves.The accuracy of identification results is limited by the experience,research interests,and identification level of the identifier,as well as the complexity of the rock composition.To improve the efficiency of rock hand specimen identification,this paper proposes a method for rock image recognition and classification based on deep learning and the Inception-v3 model.It encompasses the preprocessing of collected photographs of typical intrusive rock hand specimens,along with augmenting the sample size through data augmentation methods,culminating in a comprehensive dataset comprising 12501 samples.Experimental results show that the model has good learning ability when there is sufficient data.Through iterative training of the Inception-v3 model on the rock dataset,the accuracy of rock image recognition reaches 92.83%,with a loss of only 0.2156.Currently,several common types of intrusive rocks can be identified:gabbro,granite,diorite,peridotite,granodiorite,diabase,and granite porphyry.Software is developed for open use by geological workers to improve work efficiency.

Wireless Preamplifier for the Specimen Current Mode Detector in a SEM

Using a scanning electron microscope (SEM) in the back-scattered electron (BSE) mode the composition of multi-element specimens may be determined based on the strong dependence of emission coefficient η on the average atomic number of elements Z. The output video signal of the usual BSE detectors is produced from their sensors, and the larger proportion of high-energy electrons with modified spectrum is added. Since η = is/ip (is and ip currents of specimen and probe), better accuracy must be achieved by direct measurements those currents on the specimen surface. Here, an experimental model of a current detector for a presented specimen is described. The cage is mounted on the carousel of the moving specimen stage. The input of the preamplifier is connected to the specimen holder in the form of a disk, the diameter of which is 12 mm. When the probe along its surface scanned, the input potential begins to pulsate with a negative polarity. The output of this preamplifier is connected to a small light-emitting diode, which creates intensity-modulated radiation in the chamber. Thus created the light video signal will be picked up by the photomultiplier of the E-T detector. The modes of true SE and BSE are set by applying tens bias volts of various polarities to the specimens or the cage itself.

Application Effect of Feedforward Control in Outpatient Blood Specimen Management

Objective:To analyze the application effect of feedforward control in outpatient blood specimen management.Methods:1,200 patients who had their venous blood collected in outpatient phlebotomy room of our hospital's outpatient clinic from January 2021 to April 2021 were selected as study subjects and divided into 600 cases in the control group and 600 cases in the observation group.The two groups of patients were compared in terms of their satisfaction with the staff,the efficiency of the nurses and the quality of nursing care,turnaround time before specimen analysis,the rejection rate of the blood specimens,and the time of result reporting.Results:After the implementation of feedforward control,patients'satisfaction with staff,nurses work efficiency and quality of care,turnaround time before specimen analysis,specimen rejection rate,and result reporting time in the observation group were significantly higher than those in the control group(P<0.05).Conclusion:The application of feedforward control in the management of outpatient blood specimens has significant effect,which effectively improves patients'satisfaction,enhances the efficiency of nurses and the quality of nursing care,shortens the turnaround time of specimens before analysis and the reporting time of results,and reduces the rejection rate of specimens.

基于闭环理论的病理标本管理流程优化与实践

本研究依托闭环理论构建大型三级甲等医院病理标本管理流程,以保障病理标本准确、有效、及时送检,减少医疗安全隐患。案例医院通过完善组织管理、健全管理制度、应用闭环模式提供流程优化组织保障,结合基础质控、环节质控、终末质控构建全流程闭环追溯机制。闭环管理实施后,案例医院手术病理标本及时送检率提升至99.28%,病理标本相关不良事件发生率降低至0.003‰,异常病理报告通知率达到100%(P<0.01)。案例医院构建的病理标本管理流程有利于标本的全程追踪和动态管理,有效保障医疗质量和患者安全。

Stability of SARS Coronavirus in Human Specimens and Environment and Its Sensitivity to Heating and UV Irradiation

Objective The causal agent for SARS is considered as a novel coronavirus that has never been described both in human and animals previously. The stability of SARS coronavirus in human specimens and in environments was studied. Methods Using a SARS coronavirus strain CoV-P9, which was isolated from pharyngeal swab of a probable SARS case in Beijing, its stability in mimic human specimens and in mimic environment including surfaces of commonly used materials or in household conditions, as well as its resistances to temperature and UV irradiation were analyzed. A total of 106 TCID50 viruses were placed in each tested condition, and changes of the viral infectivity in samples after treatments were measured by evaluating cytopathic effect (CPE) in cell line Vero-E6 at 48 h after infectionn. Results The results showed that SARS coronavirus in the testing condition could survive in serum, 1:20 diluted sputum and feces for at least 96 h, whereas it could remain alive in urine for at least 72 h with a low level of infectivity. The survival abilities on the surfaces of eight different materials and in water were quite comparable, revealing reduction of infectivity after 72 to 96 h exposure. Viruses stayed stable at 4℃, at room temperature (20℃) and at 37℃ for at least 2 h without remarkable change in the infectious ability in cells, but were converted to be non-infectious after 90-, 60- and 30-min exposure at 56℃, at 67℃ and at 75℃, respectively. Irradiation of UV for 60 min on the virus in culture medium resulted in the destruction of viral infectivity at an undetectable level. Conclusion The survival ability of SARS coronavirus in human specimens and in environments seems to be relatively strong. Heating and UV irradiation can efficiently eliminate the viral infectivity.

Transanal natural orifice specimen extraction for laparoscopic anterior resection in rectal cancer

AIM: To investigate whether transanal natural orifice specimen extraction (NOSE) is a better technique for rectal cancer resection.METHODS: A prospectively designed database of a consecutive series of patients undergoing laparoscopic low anterior resection for rectal cancer with various tumor-node-metastasis classi?cations from March 2011 to February 2012 at the First Affiliated Hospital of Sun Yat-Sen University was analyzed. Patient selection for transanal specimen extraction and intracorporeal anastomosis was made on the basis of tumor size and distance of rectal lesions from the anal verge. Demographic data, operative parameters, and postoperative outcomes were assessed.RESULTS: None of the patients was converted to laparotomy. Respectively, there were 16 cases in the low anastomosis and five in the ultralow anastomosis groups. Mean age of the patients was 45.4 years, and mean body mass index was 23.1 kg/m2. Mean distance of the lower edge of the lesion from the anal verge was 8.3 cm. Mean operating time was 132 min, and mean intraoperative blood loss was 84 mL. According to the principle of rectal cancer surgery, we performed D2 lymph node dissection in 13 cases and D3 in eight. Mean lymph nodes harvest was 17.8, and the number of positive lymph nodes was 3.4. Median hospital stay was 6.7 d. No serious postoperative complication occurred except for one anastomotic leakage. All patients remained disease free. Mean Wexner score was 3.7 at 11 mo after the operation.CONCLUSION: Transanal NOSE for total laparoscopic low/ultralow anterior resection is feasible, safe and oncologically sound. Further studies with long-term outcomes are needed to explore its potential advantages.

Robotic gastrectomy with transvaginal specimen extraction for female gastric cancer patients

AIM: To describe the application of complete robotic gastrectomy with transvaginal specimen extraction(TVSE) for gastric cancer patients.METHODS: Between July and November 2014, eight female patients who were diagnosed with gastric adenocarcinoma underwent a TVSE following a full robot-sewn gastrectomy. According to the tumor location, the patients were allocated to two different groups; two patients received robotic total gastrectomy with TVSE and the other six received robotic distal gastrectomy with TVSE.RESULTS: Surgical procedures were successfully performed in all eight cases without conversion. The mean age was 55.3(range, 42-69) years, and the mean body mass index was 23.2(range, 21.6-26.0) kg/m2. The mean total operative time and blood loss were 224(range, 200-298) min and 62.5(range, 50-150) m L, respectively. The mean postoperative hospital stay was 3.6(range, 3-5) d. The mean number of lymph nodes resected was 23.6(range, 17-27). None was readmitted within 30 d of postoperation. During the follow-up, no stricture developed nor was any anastomotic leakage detected.CONCLUSION: It is possible to perform a TVSE following a full robot-sewn gastrectomy with standard D2 lymph node resection for female gastric cancer patients.