Simultaneous removal of NO and SO_2 from dry gas stream using non-thermal plasma

In order to investigate the feasibility of sequential removal NO and SO2 using non-thermal plasma and adsorbent simultaneously, the removal of NO and SO2 from dry gas stream （NO/SO2/N2/O2） with very little O2 using non-thermal plasma was investigated using a coaxial dielectric barrier discharge. Comparative experiments were carried out in the dry gas stream with and without Ar respectively at O2 concentration of 0.1%. The results showed that NO could be removed remarkably and it would be enhanced in the presence of Ar in the dry gas stream. It seems that SO2 could not be removed unless there is Ar in the dry gas stream. The mechanism of removal of NO and SO2 in the dry gas stream was discussed.

Simultaneous Removal of Soot and NO_x over Precious Metal Catalysts O_2-Rich Atmospheres and in the Presence of H_2O and SO_2

The activities of ZrO_2-supported precious metal catalysts for simultaneous removal of soot and NO_x in the presence of rich O_2and H_2O as well as SO_2 have been studied by keeping loose contact between catalyst and soot.The results show that only Ru,Ir and Rh have catalytic activity for simultaneous removal of soot and NO_x and the order of catalytic activity is Ru > Ir > Rh.Pt has the catalytic activity only for the removal of soot,and Ag,Pd,and Au have hardly any catalytic activities for the removal of soot and NO_x.The relationships between catalytic activity of precious metal catalysts and various reaction conditions were discussed.

Simultaneous removing SO_2 and NO by a new system containing cobalt complex

Absorption and catalytic oxidation of nitric oxide can be achieved by using cobalt（Ⅲ） ethylenediamine （Co（en）3^3＋. When simultaneous absorbing SO2 and NO, the precipitation of Co2（SO3）3 will be yielded and the NO removal will be decreased. A new catalyst system using Co（en）3^3＋ coupled with urea has been developed to simultaneous remove NO and SO2 in the flue gas. NO is absorbed and catalytically oxidized to nitrite and nitrate by Co（en）3^3＋. The dissolved oxygen in scrubbing solution from the feed stream acts as oxidant. Urea restrains the precipitation of Co2（SO3）3 by oxidizing SO3^2-to SO4^2- as COSO4 is more soluble in water. The experimental results proved that nearly all SO3^2- can be oxidized to SO4^2- and the high NO and SO2 removal could be obtained with the new system. The NO removal is influenced by gas flow rate, the concentration of Co（en）3^3＋ and urea in the absorption solution, the temperature of the scrubbing solution and the content of oxygen in the flue gas. The low gas flow rate is favorable to increase the NO removal. The experiments proved that the NO removal could be maintained at more than 95% by the system of 0.02 mol/L Co（en）3^3＋ and 1% urea at 50℃ with 10% O2 in the flue gas.

A study on simultaneous removal of NO and SO2 by using sodium persulfate aqueous scrubbing

Nitric oxide （NO） removal and sulfur dioxide （SO2） removal by sodium persulfate （Na2S2O8） were studied in a Bubble Column Reactor. The proposed reaction pathways of NO and SO2 removal are discussed. The effects of temperatures （35-90℃）, Na25208 （0.05-0.5 mol·L-1）, FeSO4 （0.5-5.0 m mol·L-1） and H2O2 （0.25 mol·L-1） on NO and SO2 removal were investigated. The results indicated that increased persulfate concentration led to increase in NO removal at various temperatures. SO2 was almost completely removed in the temperature range of 55-85 ℃. Fe2 ＋ accelerated persulfate activation and enhanced NO removal efficiency. At 0.2 mol· L- 1 Na2S2O8 and 0.5-1.0 mmol· L-1Fe2 ＋, NO removal of 93.5%-99% was obtained at 75-90 ℃, SO2 removal was higher than 99% at all temperatures. The addition of 0.25 mol. L i H202 into 0.2 mol·L-1· Na2S2O8 solution promoted NO removal efficiency apparently until utterly decomposition of H2O2, the SO2 removal was as high as 98.4% separately at 35 ℃ and 80 ℃.

Simultaneous Removal of COS and H_2S at Low Temperatures over Nanoparticle a-FeOOH Based Catalysts

Catalysts using α-FeOOH nanoparticles as the active ingredient were testedby a microreactor-chromatography assessing apparatus at atmospheric pressure between 25 and 60 ℃with a gas hourly space velocity of 10,000 h^(-1), while the removal performance of H_2S withcatalysts was investigated using the thermal gravimetric method. The results show that the catalystsare highly active for COS hydrolysis at low temperatures (≤60 ℃) and high gas hourly spacevelocity, and the highest activity can reach 100%. The catalyst is particularly stable for 12 h, andno deactivation is observed. Nanoparticle α-FeOOH prepared using hydrated iron sulfate showshigher COS hydrolysis activity, and the optimum calcination temperature for the catalyst is 260 ℃.In addition, the catalysts can remove COS and H_2S simultaneously, and 60 ℃ is favorable for theremoval of H_2S. The compensation effect exists in nanoparticle-based catalysts.

Highly Selective Electrocatalytic CuEDTA Reduction by MoS_(2) Nanosheets for Efficient Pollutant Removal and Simultaneous Electric Power Output

Electrocatalytic reduction of ethylenediamine tetraacetic acid copper(CuEDTA),a typical refractory heavy metal complexation pollutant,is an environmental benign method that operates at mild condition.Unfortunately,the selective reduction of CuEDTA is still a big challenge in cathodic process.In this work,we report a MoS_(2) nanosheet/graphite felt(GF)cathode,which achieves an average Faraday efficiency of 29.6%and specific removal rate(SRR)of 0.042 mol/cm^(2)/h for CuEDTA at−0.65 V vs SCE(saturated calomel electrode),both of which are much higher than those of the commonly reported electrooxidation technology-based removal systems.Moreover,a proofof-concept CuEDTA/Zn battery with Zn anode and MoS_(2)/GF cathode is demonstrated,which has bifunctions of simultaneous CuEDTA removal and energy output.This is one of the pioneer studies on the electrocatalytic reduction of heavy metal complex and CuEDTA/Zn battery,which brings new insights in developing efficient electrocatalytic reduction system for pollution control and energy output.

Simultaneous removal of ethanol, acetaldehyde and nitrogen oxides over V-Pd/γ-Al_2O_3-TiO_2 catalyst

V-Pd/γ-Al2O3-TiO2 catalysts with different vanadium contents were prepared by a combined sol-gel and impregnation method. X-ray diffraction （XRD）, N2 adsorption-desorption （BET）, X-ray photoelectron spectroscopy （XPS） and catalytic removal of ethanol, acetaldehyde and nitrogen oxides at low temperature （〈300 ？C） were used to assess the properties of the catalysts. The results showed that the sample with 1wt% vanadium exhibited an excellent catalytic performance for simultaneous removal of ethanol, acetaldehyde and nitrogen oxides. The conversions of ethanol, acetaldehyde and nitrogen oxides at 250 ？C were 100%, 74.4% and 98.7%, respectively. V-Pd/γ-Al2O3-TiO2 catalyst with 1 wt% vanadium showed the largest surface area and higher dispersion of vanadium oxide on the catalyst surface, and possessed a larger mole fraction of V4＋ species and unique PdO species on the surface, which can be attributed to the strong synergistic effect among palladium, vanadium and the carriers. The higher activity of V-Pd/γ-Al2O3-TiO2 catalyst is related to the V4＋ and Pd2＋ species on the surface, which might be favorable for the formation of active sites.

NH_(2)-MIL-53(Al)for Simultaneous Removal and Detection of Fluoride Anions

To address the limitations of the separate fluoride removal or detection in the existing materials,herein,amino-decorated metal organic frameworks NH_(2)-MIL-53(Al)have been succinctly fabricated by a sol-hydrothermal method for simultaneous removal and determination of fluoride.As a consequence,the proposed NH_(2)-MIL-53(Al)features high uptake capacity(202.5 mg/g)as well as fast adsorption rate,being capable of treating 5 ppm of fluoride solution to below the permitted threshold in drinking water within 15 min.Specifically,the specific binding between fluoride and NH_(2)-MIL-53(Al)results in the release of fluorescent ligand NH2-BDC,conducive to the determination of fluoride via a concentration-dependent fluorescence enhancement effect.As expected,the resulting NH_(2)-MIL-53(Al)sensor exhibits selective and sensitive detection(with the detection limit of 0.31μmol/L)toward fluoride accompanied with a wide response interval(0.5-100μmol/L).More importantly,the developed sensor can be utilized for fluoride detection in practical water systems with satisfying recoveries from 89.6% to 116.1%,confirming its feasibility in monitoring the practical fluoride-contaminated waters.

Simultaneous Removal of SO2 and NOx From Flue Gas

In this paper,the recent progress of simultaneous removal of SO_2 and NO_x process at home and abroad is reviewed.We mainly introduced calcium based absorbent catalytic oxidation method,complexation absorption process,Electron beam method et al,principle of each technology are described,and the development direction was put forward in the future.

Hierarchical Reduced Graphene Oxide-MnO_(2)@Polypyrrole Coaxial Nanotube Composite Hydrogel as a Potential Adsorbent for Cr(Ⅵ)Removal

A hierarchical reduced graphene oxide-MnO_(2)@polypyrrole coaxial nanotube composite hydrogel was prepared via oxidative polymerization of pyrrole in the presence of MnO_(2)nanotubes,followed by the hydrothermal treatment of graphene oxide and MnO_(2)@polypyrrole coaxial nanotubes.The stable composite hydrogel with a hierarchical network was composed of one-dimensional MnO_(2)@polypyrrole coaxial nanotube and two-dimensional graphene nanosheet and characterized by scanning electron microscope,Fourier transform infrared spectroscopy,X-ray diffraction,Brunauer-Emmett-Teller surface,and X-ray photoelectron spectroscopy measurements.The composite hydrogel can be used as an efficient adsorbent for Cr(Ⅵ)removal due to the synergistic interaction between graphene and MnO_(2)@polypyrrole and the hierarchical structure of the hydrogel.Moreover,the composite hydrogel is easily separated because of its stable monolith,and it is reusable(76.8%of removal ability remaining after five adsorption-desorption cycles).The simple fabrication and cost-effective separation process together with the excellent absorption performance endow the composite hydrogel with great potential for practical wastewater treatment.

Efficient removal of Al(Ⅲ)and P507 from high concentration MgCl_(2)solution based on in-situ reaction strategy

For a highly efficient recycling of a wastewater containing a high concentration of MgCl_(2),Al(Ⅲ)and P507 were scheduled to be removed in advance.In this study,the in-situ removal of Al(Ⅲ)and P507 from a high concentration MgCl_(2)solution at different pH values and Al/P molar ratios was investigated.The results showed that P507 formed organic complexes of Al_(x)(OH)_y^(Z+)-P507 at pH of 2.0-4.0.At pH of 4.0-5.0,Al(Ⅲ)precipitated and transferred into Al(OH)_(3)with a flocculent amorphous morphology.Active sites on the Al(OH)_(3)surface enhanced the removal efficiency of P507.At pH of 6.0-6.5,Al(Ⅲ)and Mg(Ⅱ)formed layered crystalline Al(OH)_(3)and MgAl_(2)(OH)_(8with)small pore channels and fewer active sites,resulting in a reduced removal efficiency of P507.When the Al/P molar ratio exceeded 13 and the pH was between 4.0 and 5.0,the removal rates of both Al(Ⅲ)and P507 were higher than98%,while the concentration loss of Mg(Ⅱ)was only 0.2%-0.9%.

Simultaneous nitrification and denitrification in step feeding biological nitrogen removal process

The simultaneous nitrification and denitrification in step-feeding biological nitrogen removal process were investigated under different influent substrate concentrations and aeration flow rates. Biological occurrence of simultaneous nitrification and denitrification was verified in the aspect of nitrogen mass balance and alkalinity. The experimental results also showed that there was a distinct linear relationship between simultaneous nitrification and denitrification and DO concentration under the conditions of low and high aeration flow rate. In each experimental run the floc sizes of activated sludge were also measured and the results showed that simultaneous nitrification and denitrification could occur with very small size of floc.

TiO2-PES Fibrous Composite Material for Ammonia Removal Using UV-A Photocatalyst

This study focused on the development and characterization of TiO2-PES composite fibers with varying TiO2 loading amounts using a phase inversion process. The resulting composite fibers exhibited a sponge-like structure with embedded TiO2 nanoparticles within a polymer matrix. Their photocatalytic performance for ammonia removal from aqueous solutions under UV-A light exposure was thoroughly investigated. The findings revealed that PeTi8 composite fibers displayed superior adsorption capacity compared to other samples. Moreover, the study explored the impact of pH, light intensity, and catalyst dosage on the photocatalytic degradation of ammonia. Adsorption equilibrium isotherms closely followed the Langmuir model, with the results indicating a correlation between qm values of 2.49 mg/g and the porous structure of the adsorbents. The research underscored the efficacy of TiO2 composite fibers in the photocatalytic removal of aqueous under UV-A light. Notably, increasing the distance between the photocatalyst and the light source resulted in de-creased hydroxyl radical concentration, influencing photocatalytic efficiency. These findings contribute to our understanding of TiO2 composite fibers as promising photocatalysts for ammonia removal in water treatment applications.

Nitrogen Removal by Simultaneous Nitrification and Denitrification via Nitrite in a Sequence Hybrid Biological Reactor

Sequence hybrid biological reactor （SHBR） was proposed, and some key control parameters were investigated for nitrogen removal from wastewater by simultaneous nitrification and denitrification （SND） via nitrite. SND via nitrite was achieved in SHBR by controlling demand oxygen （DO） concentration. There was a programmed decrease of the DO from 2.50 mg·L^-1 to 0.30 mg·L^-1, and the average nitrite accumulation rate （NAR） was increased from 16.5% to 95.5% in 3 weeks. Subsequently, further increase in DO concentration to 1.50 mg·L^-1 did not destroy the partial nitrification to nitrite. The results showed that limited air flow rate to cause oxygen deficiency in the reactor would eventually induce only nitrification to nitrite and not further to nitrate. Nitrogen removal efficiency was increased with the increase in NAR, that is, NAR was increased from 60% to 90%, and total nitrogen removal efficiency was increased from 68% to 85%. The SHBR could tolerate high organic loading rate （OLR）, COD and ammonia-nitrogen removal efficiency were greater than 92% and 93.5%, respectively,, and it even operated under low DO concentration （0.5 mg·L^-1） and maintained high OLR （4.0 kg COD·m^-3·d^-1）. The presence of biofilm positively affected the activated sludge settling capability, and sludge volume index （SVI） of activated sludge in SHBR never hit more than 90 ml·L^-1 throughout the experiments.

Simultaneous removal of Cr(Ⅵ), Cd, and Pb from aqueous solution by iron sulfide nanoparticles: Influencing factors and interactions of metals

Cadmium(Cd),lead(Pb),and hexavalent chromium(Cr(Ⅵ)) are often found in soils and water affected by metal smelting,chemical manufacturing,and electroplating.In this study,synthetic iron sulfide nanoparticles(FeS NPs) were stabilized with carboxymethyl cellulose(CMC) and utilized to remove Cr(Ⅵ),Cd,and Pb from an aqueous solution.Batch experiments,a Visual MINTEQ model,scanning electron microscopy(SEM),X-ray diffraction(XRD),and X-ray photoelectron spectrometer(XPS) analysis were used to determine the removal efficiencies,influencing factors,and mechanisms.The FeS NP suspension simultaneously removed Cr(Ⅵ),Cd,and Pb from an aqueous solution.The concentrations of Cr(Ⅵ),Cd,and Pb decreased from 50,10,and 50 mg·L^(-1) to 2.5,0.1,and 0.1 mg·L^(-1),respectively.The removal capacities were up to 418,96,and 585 mg per gram of stabilized FeS NPs,respectively.The acidic conditions significantly favored the removal of aqueous Cr(Ⅵ) while the alkaline conditions favored the removal of Cd and Pb.Oxygen slightly inhibited the removal of Cr(Ⅵ),but it had no significant influence on the removal of Cd and Pb.A potential mechanism was proposed for the simultaneous removal of Cr(Ⅵ),Cd,and Pb using FeS NPs.The interactions of the three heavy metals involved a cationic bridging effect on Cr(Ⅵ) by Cd,an enhanced adsorption effect on Cd by [Cr,Fe](OH)_3,precipitation of PbCrO_4,and transformation of PbCrO_4 to PbS.Therefore,FeS NPs have a high potential for use in the simultaneous removal of Cr(Ⅵ),Cd,and Pb from contaminated aqueous solutions.

Removal of SO_2 and NO_x by Pulsed Corona Combined with in situ Ca(OH)2 Absorption

Removal of SO2 and NOx by pulsed corona combined with in situ alkali absorption was experimentally investigated.In the reactor,a plate-wire-plate combination is devised for generating pulsed corona and then alkaline absorbent slurries were introduced into the reactor by a continuous band conveying system to capture the gaseous reaction products.It was found that both SO2 and NO could be removed by corona combined with in situ alkali absorption.The removal of SO2 increased to 75%with the corona discharge,compared with 60%removal only with Ca(OH)2 absorption.About 40%removal of NO was reached by pulsed corona combined with in situ Ca(OH)2 absorption.It was found that SO2 and NO in the gas stream are oxidized to SO3 and NO2 by pulsed corona respectively,and then absorbed by the alkali in the reactor.The removals of SO2 as well as NO were higher with Ca(OH)2 as the absorbent,compared with using CaCO3 or ZnO.

Simultaneous removal of nitrogen and phosphorus from swine wastewater in a sequencing batch biofilm reactor

In this study, the performance of a sequencing batch biofilm reactor(SBBR) for removal of nitrogen and phosphorus from swine wastewater was evaluated. The replacement rate of wastewater was set at 12.5% throughout the experiment. The anaerobic and aerobic times were 3 h and 7 h, respectively, and the dissolved oxygen concentration of the aerobic phase was about 3.95 mg·L-1. The SBBR process demonstrated good performance in treating swine wastewater. The percentage removal of total chemical oxygen demand(COD), ammonia nitrogen(NH4+-N), total nitrogen(TN), and total phosphorus(TP) was 98.2%, 95.7%, 95.6%, and 96.2% at effluent concentrations of COD85.6 mg·L-1, NH4+-N 35.22 mg·L-1, TN 44.64 mg·L-1, and TP 1.13 mg·L-1, respectively. Simultaneous nitrification and denitrification phenomenon was observed. Further improvement in removal efficiency of NH4+-N and TN occurred at COD/TN ratio of 11:1, with effluent concentrations at NH4+-N 18.5 mg·L-1and TN 34 mg·L-1, while no such improvement in COD and TP removal was found. Microbial electron microscopy analysis showed that the filler surface was covered with a thick biofilm, forming an anaerobic–aerobic microenvironment and facilitating the removal of nitrogen, phosphorus and organic matters. A long-term experiment(15 weeks) showed that stable removal efficiency for N and P could be achieved in the SBBR system.

Simultaneous catalytic removal of NOx and diesel PM over La_(0.9) K_(0.1) CoO_3 catalyst assisted by plasma

The simultaneous removal of NOx and particulate matter(PM) from diesel exhaust is investigated over a mixed metal oxide catalyst of La 0.9 K 0.1 CoO 3 loaded on γ-Al 2O 3 spherules with the assistant of plasma. It was found that NOx was reduced by PM in oxygen rich atmosphere, the CO 2 and N 2 were produced in the same temperature window without considering the N 2 formed by plasma decomposition. As a result, the temperature for the PM combustion decreases and the reduction efficiency of NOx to N 2 increases during the plasma process, which indicated that the activity of the catalyst can be improved by plasma. The NOx is decomposed by plasma at both low temperature and high temperature. Therefore, the whole efficiency of NOx conversion is enhanced.

SO_2/Hg removal from flue gas by dry FGD

To study the mechanism of SO2 and Hg removal from flue gas, an experimental packed bed reactor was designed to simulate the dry FGD, where a mixture of lime and fly ash in ratio 1：3 w/w was used as the S02 and Hg sorbent, and steam at temperature of 100 ℃ was applied for activation of the sorbent, while the activation time set to 20 rain. The experimental factors including the SO2/Hg sorbent characteristics, 50% breakthrough time for SO2/Hg removal, sorbent packed bed depth and reaction temperature were investigated. The experimental results show that after steam activation, the BET specific surface area and specific pore volume increased from 37.8 to 45.5 m^2/g and from 0.42 to 0.51 cm^3/g, respectively. With activation of the sorbent by steam, the 50% breakthrough times of SO2 and Hg removal increased from 34 to 42 rain and from 23 to 45 rain, respectively. When the packed bed depth was increased from 5 to 25 ram. the 50% breakthrough times for Hg and S02 removal increased from 12 to 52 rain and from 6 to 47 rain, respectively. With the increase of the reaction temperature, the 50% breakthrough of SO2/Hg removal decreased accordingly. Steam activation can efficiently improve SO2/Hg removal simultaneously.

Science Letters:Simultaneous removal of nitrate and heavy metals by iron metal

Great attention should be paid now to simultaneously removing common pollutants, especially inorganic pollutants such as nitrate and heavy metals, as individual removal has been investigated extensively. Removing common pollutants simul- taneously by iron metal is a very effective alternative method. Near neutral pH, heavy metals, such as copper and nickel, can be removed rapidly by iron metal, while nitrate removal very much slower than that of copper and nickel, and copper can accelerate nitrate removal when both are removed simultaneously. Even a little amount of copper can enhance nitrate removal efficiently. Different mechanisms of these contaminants removal by iron metal were also discussed.