A new analytical model of high voltage silicon on insulator(SOI) thin film devices

A new analytical model of high voltage silicon on insulator （SOI） thin film devices is proposed, and a formula of silicon critical electric field is derived as a function of silicon film thickness by solving a 2D Poisson equation from an effective ionization rate, with a threshold energy taken into account for electron multiplying. Unlike a conventional silicon critical electric field that is constant and independent of silicon film thickness, the proposed silicon critical electric field increases sharply with silicon fihn thickness decreasing especially in the case of thin films, and can come to 141V/μm at a film thickness of 0.1 μm which is much larger than the normal value of about 30 V/μm. From the proposed formula of silicon critical electric field, the expressions of dielectric layer electric field and vertical breakdown voltage （VB,V） are obtained. Based on the model, an ultra thin film can be used to enhance dielectric layer electric field and so increase vertical breakdown voltage for SOI devices because of its high silicon critical electric field, and with a dielectric layer thickness of 2 μm the vertical breakdown voltages reach 852 and 300V for the silicon film thicknesses of 0.1 and 5μm, respectively. In addition, a relation between dielectric layer thickness and silicon film thickness is obtained, indicating a minimum vertical breakdown voltage that should be avoided when an SOI device is designed. 2D simulated results and some experimental results are in good agreement with analytical results.

THE GROWTH OF MONOCRYSTALLINE SILICON THIN FILM ON INSULATOR (SOI) BY SCANNING ELECTRON BEAM

An experiment for preparation of SOI films by using the scanning electron beam to modify the polycrystalline silicon on SiO2 is presented. This method takes on the epitaxial lateral growth of liquid phase with the crystallon to form monocrystalline silicon films. The effects of the beam power density, scanning velocity, temperature of the substrates and the construction of samples on the quality of the monocrystalline silicon films were discussed. A good experimental result has been obtained, the monocrystalline silicon zone is nearly 200×25μm2.

Design and Fabrication of Ultracompact 3-dB MMI Coupler in Silicon-on-Insulator

An ultracompact 3 dB coupler is designed and fabricated in silicon on insulator,based on 1×2 line tapered multimode interference (MMI) coupler.Comparing with the conventional straight MMI coupler,the device is ～40% shorter in length.The device exhibits uniformity of 1 3dB and excess loss of 2 5dB.

Transfer of Thin Epitaxial Silicon Films by Wafer Bonding and Splitting of Double Layered Porous Silicon for SOI Fabrication

A double layered porous silicon with different porosity is formed on a heavy doped p type Si(111) substrate by changing current density during the anodizing.Then a high quality epitaxial mono crystalline silicon film is grown on the porous silicon using an ultra high vacuum electron beam evaporator.This wafer is bonded with other silicon wafer with a thermal oxide layer at room temperature.The bonded pairs are split along the porous silicon layer during subsequent thermal annealing.Thus the epitaxial Si film is transferred to the oxidized wafer to form a silicon on insulator structure.SEM,XTEM,spreading resistance probe and Hall measurement show that the SOI structure has good structural and electrical quality.

Dependence of R-G Currenton Bulk Traps Characteristics and Silicon Film Structure in SOI Gated-Diode

The dependence of the Recombination- Generation( R- G) current on the bulk trap characteristics and sili- con film structure in SOI lateral p+ p- n+ diode has been analyzed num erically by using the simulation tool,DESSIS- ISE.By varying the bulk trap characteristics such as the trap density and energy level spectrum systematically,the dependence of the R- G current on both of them has been dem onstrated in details.Moreover,the silicon film doping concentration and thickness are changed to make silicon body varies from the fully- depletion m ode into the partial- ly- depletion one.The influence of the transfer of silicon body characteristics on the R- G currenthas also been care- fully examined.A better understanding is obtained of the behavior of bulk trap R- G current in the SOI lateral gat- ed- diode.

SOI高压LDMOS器件氧化层抗总电离剂量辐射效应研究

绝缘体上硅(SOI)高压横向扩散金属氧化物半导体(LDMOS)器件是高压集成电路的核心器件,对其进行了总电离剂量(TID)辐射效应研究。利用仿真软件研究了器件栅氧化层、场氧化层和埋氧化层辐射陷阱电荷对电场和载流子分布的调制作用,栅氧化层辐射陷阱电荷主要作用于器件沟道区,而场氧化层和埋氧化层辐射陷阱电荷则主要作用于器件漂移区;辐射陷阱电荷在器件内部感生出的镜像电荷改变了器件原有的电场和载流子分布,从而导致器件阈值电压、击穿电压和导通电阻等参数的退化。对80 V SOI高压LDMOS器件进行了总电离剂量辐射实验,结果表明在ON态和OFF态下随着辐射剂量的增加器件性能逐步衰退,当累积辐射剂量为200 krad(Si)时,器件的击穿电压大于80 V,阈值电压漂移为0.3 V,器件抗总电离剂量辐射能力大于200 krad(Si)。

Estimation of pulsed laser-induced single event transient in a partially depleted silicon-on-insulator 0.18-μm MOSFET

In this paper, we investigate the single event transient （SET） occurring in partially depleted silicon-on-insulator （PDSOI） metal-oxide-semiconductor （MOS） devices irradiated by pulsed laser beams. Transient signal characteristics of a 0.18-p.m single MOS device, such as SET pulse width, pulse maximum, and collected charge, are measured and an- alyzed at wafer level. We analyze in detail the influences of supply voltage and pulse energy on the SET characteristics of the device under test （DUT）. The dependences of SET characteristics on drain-induced barrier lowering （DIBL） and the parasitic bipolar junction transistor （PBJT） are also discussed. These results provide a guide for radiation-hardened deep sub-micrometer PDSOI technology for space electronics applications.

热老化对不同封装形式SOI基压阻式芯片的影响

采用热老化的手段提高封装后芯片的输出稳定性及使用寿命,并对热老化温度与老化时间的匹配问题进行了研究。首先介绍了压阻传感器的老化机理,然后在不同温度下对同批次不同封装形式绝缘体上硅(SOI)基压阻芯片进行老化,并对芯片老化前后数据进行对比。结果表明,300℃加电老化情况下,芯片稳定输出的时间为12h,且老化后芯片的各项指标均有改善。在温度允许范围内,适当的老化温度可以使芯片达到稳定输出状态,提升工作效率的同时为优化SOI基压阻芯片的老化时间提供了参考。

Effects of source-drain underlaps on the performance of silicon nanowire on insulator transistors

The effects of source-drain underlaps on the performance of a top gate silicon nanowire on insulator transistor are studied using a three dimensional(3D) self-consistent Poisson-Schrodinger quantum simulation. Voltage-controlled tunnel barrier is the device transport physics. The off current, the on/off current ratio, and the inverse subthreshold slope are improved while the on current is degraded with underlap. The physics behind this behavior is the modulation of a tunnel barrier with underlap. The underlap primarily affects the tunneling component of drain current. About 50% contribution to the gate capacitance comes from the fringing electric fields emanating from the gate metal to the source and drain. The gate capacitance reduces with underlap, which should reduce the intrinsic switching delay and increase the intrinsic cut-off frequency. However, both the on current and the transconductance reduce with underlap, and the consequence is the increase of delay and the reduction of cut-off frequency.

Microwave absorption and thermal properties of coral-like SiC aerogel composites prepared by water glass as a silicon source

As a heat-resistant wave-absorbing material,silicon carbide(SiC)aerogel has become a research hotspot at present.However,the most common silicon sources are organosilanes,which are costly and toxic.In this work,SiC aerogels were successfully prepared by using water glass as the silicon source.Specifically,the microstructure and chemical composition of SiC aerogels were controlled by adjusting the Si to C molar ratio during the sol–gel process,and the effect on SiC aerogel microwave absorption properties was investigated.The SiC aerogels prepared with Si:C molar ratio of 1:1 have an effective electromagnetic wave absorption capacity,with a minimum reflection loss value of-46.30 dB at 12.88 GHz and an effective frequency bandwidth of 4.02 GHz.They also have good physical properties,such as the density of0.0444 g/cm^(3),the thermal conductivity of 0.0621 W/(m·K),and the specific surface area of 1099 m^(2)/g.These lightweight composites with microwave-absorbing properties and low thermal conductivity can be used as thermal protection materials for space shuttles and reusable carriers.

Analytical base collector depletion capacitance in vertical SiGe heterojunction bipolar transistors fabricated on CMOS-compatible silicon on insulator

The base-collector depletion capacitance for vertical SiGe npn heterojunction bipolar transistors （HBTs） on silicon on insulator （SOI） is split into vertical and lateral parts. This paper proposes a novel analytical depletion capacitance model of this structure for the first time. A large discrepancy is predicted when the present model is compared with the conventional depletion model, and it is shown that the capacitance decreases with the increase of the reverse collector- base bias-and shows a kink as the reverse collector-base bias reaches the effective vertical punch-through voltage while the voltage differs with the collector doping concentrations, which is consistent with measurement results. The model can be employed for a fast evaluation of the depletion capacitance of an SOI SiGe HBT and has useful applications on the design and simulation of high performance SiGe circuits and devices.

基于45 nm CMOS SOI工艺的毫米波双频段低相噪压控振荡器设计

本文基于45 nm互补金属氧化物半导体绝缘体上硅工艺(Complementary Metal Oxide Semiconductor Silicon On Insulator,CMOS SOI)设计了一款支持5G毫米波24.25~27.5 GHz和37~43.5 GHz双频段的低相位噪声压控振荡器(Voltage Controlled Oscillator,VCO).基于CMOS SOI工艺良好的晶体管开关特性,结合开关电容阵列及开关电感方案,提高宽带调谐电容、电感Q值,扩展VCO工作频段,降低相位噪声.同时,输出匹配网络也采用开关电容切换方式,实现了5G毫米波双频段良好阻抗匹配及稳定功率输出.流片测试结果表明该VCO可以完整覆盖5G毫米波双频段24.25~27.5 GHz和37~43.5 GHz,低频段输出功率-4.8~0 dBm,高频段输出功率-6.4~-2.3 dBm.在24.482 GHz载频,1 MHz频偏处的相位噪声为-105.1 dBc/Hz;在43.308 GHz载频,1 MHz频偏处的相位噪声为-95.3 dBc/Hz.VCO核心直流功耗15.3~18.5 mW,电路核心面积为0.198 mm^(2).低频段(高频段)的FoM(Figure of Merit)及FoMT优值分别达到-181.3 dBc/Hz(-175.4 dBc/Hz)、-194.3 dBc/Hz(-188.3 dBc/Hz).

Study on the defect-related emissions in the light self-ion-implanted Si films by a silicon-on-insulator structure

This paper reports that the Si＋ self-ion-implantation are conducted on the silicon-on-insulator wafers with the 2SSi＋ doses of 7 ×1012, 1 × 1013, 4 × 1013, and 3× 1014 cm-2, respectively. After the suitable annealing, these samples are characterized by using the photoluminescence technique at different recorded temperatures. Plentiful emission peaks are observed in these implanted silicon-on-insulator samples, including the unwonted intense P~ band which exhibits a great potential in the optoelectronic application. These results indicate that severe transformation of the interstitial clusters can be manipulated by the implanting dose at suitable annealing temperatures. The high critical temperatures for the photoluminescence intensity growth of the two signatures are well discussed based on the thermal ionization model of free exciton.

Analysis of single-event transient sensitivity in fully depleted silicon-on-insulator MOSFETs

Based on 3 D-TCAD simulations, single-event transient(SET) effects and charge collection mechanisms in fully depleted silicon-on-insulator(FDSOI) transistors are investigated. This work presents a comparison between28-nm technology and 0.2-lm technology to analyze the impact of strike location on SET sensitivity in FDSOI devices. Simulation results show that the most SET-sensitive region in FDSOI transistors is the drain region near the gate. An in-depth analysis shows that the bipolar amplification effect in FDSOI devices is dependent on the strike locations. In addition, when the drain contact is moved toward the drain direction, the most sensitive region drifts toward the drain and collects more charge. This provides theoretical guidance for SET hardening.

Modeling of a triple reduced surface field silicon-on-insulator lateral double-diffused metal–oxide–semiconductor field-effect transistor with low on-state resistance

An analytical model for a novel triple reduced surface field（RESURF） silicon-on-insulator（SOI） lateral doublediffused metal–oxide–semiconductor（LDMOS） field effect transistor with n-type top（N-top） layer, which can obtain a low on-state resistance, is proposed in this paper. The analytical model for surface potential and electric field distributions of the novel triple RESURF SOI LDMOS is presented by solving the two-dimensional（2D） Poisson＇s equation, which can also be applied to single, double and conventional triple RESURF SOI structures. The breakdown voltage（BV） is formulized to quantify the breakdown characteristic. Besides, the optimal integrated charge of N-top layer（Q_（ntop）） is derived, which can give guidance for doping the N-top layer. All the analytical results are well verified by numerical simulation results,showing the validity of the presented model. Hence, the proposed model can be a good tool for the device designers to provide accurate first-order design schemes and physical insights into the high voltage triple RESURF SOI device with N-top layer.

Mechanism of floating body effect mitigation via cutting off source injection in a fully-depleted silicon-on-insulator technology

In this paper, the effect of floating body effect （FBE） on a single event transient generation mechanism in fully depleted （FD） silicon-on-insulator （SOI） technology is investigated using three-dimensional technology computer-aided design （3D- TCAD） numerical simulation. The results indicate that the main SET generation mechanism is not carder drift/diffusion but floating body effect （FBE） whether for positive or negative channel metal oxide semiconductor （PMOS or NMOS）. Two stacking layout designs mitigating FBE are investigated as well, and the results indicate that the in-line stacking （IS） layout can mitigate FBE completely and is area penalty saving compared with the conventional stacking layout.

Simulation Study of Nanoscale FDSOI MOSFET Characteristics

Silicon on insulator (SOI) technology permits a good solution to the miniaturization as the MOSFET size scales down. This paper is about to compare the electrical performance of nanoscale FD-SOI MOSFET at various gate lengths. The performance is compared and contrasted with the help of threshold voltage, subthreshold slope, on-state current and leakage current. Interestingly, by decreasing the gate length, the leakage current and on-state current are increased but the threshold voltage is decreased and the sub-threshold slope is degraded. Silvaco two-dimensional simulations are used to analyze the performance of the proposed structures.

Total dose radiation response of modified commercial silicon-on-insulator materials with nitrogen implanted buried oxide

Nitrogen ions of various doses are implanted into the buried oxide （BOX） of commercial silicon-on-insulator （SOI） materials, and subsequent annealings are carried out at various temperatures. The total dose radiation responses of the nitrogen-implanted SOI wafers are characterized by the high frequency capacitance-voltage （C-V） technique after irradi- ation using a Co-60 source. It is found that there exist relatively complex relationships between the radiation hardness of the nitrogen implanted BOX and the nitrogen implantation dose at different irradiation doses. The experimental results also suggest that a lower dose nitrogen implantation and a higher post-implantation annealing temperature are suitable for improving the radiation hardness of SOI wafer. Based on the measured C V data, secondary ion mass spectrometry （SIMS）, and Fourier transform infrared （FTIR） spectroscopy, the total dose responses of the nitrogen-implanted SOI wafers are discussed.

The study on two-dimensional analytical model for gate stack fully depleted strained Si on silicon-germanium-on-insulator MOSFETs

Based on the exact resultant solution of two-dimensional Poisson＇s equation in strained Si and Si1-xCex layer, a simple and accurate two-dimensional.analytical model including surface channel potential, surface channel electric field, threshold voltage and subthreshold swing for fully depleted gate stack strained Si on silicon-germanium-on-insulator （SGOI） MOSFETs has been developed. The results show that this novel structure can suppress the short channel effects （SCE）, the drain-induced barrier-lowering （DIBL） and improve the subthreshold performance in nanoelectronics application. The model is verified by numerical simulation. The model provides the basic designing guidance of gate stack strained Si on SGOI MOSFETs.

An analytical model for coplanar waveguide on silicon-on-insulator substrate with conformal mapping technique

In this paper, the authors present an analytical model for coplanar waveguide on silicon-on-insulator substrate. The four-element topological network and the conformal mapping technique are used to analyse the capacitance and the conductance of the sandwich substrate. The validity of the model is verified by the full-wave method and the experimental data. It is found that the inductance, the resistance, the capacitance and the conductance from the analytical model show they are in good agreement with the corresponding values extracted from experimental Sparameter until 10 GHz.