ATOMIC FORCE MICROSCOPY STUDIES OF POLYCAPROLACTONE RINGED SPHERULITES

The surface morphology of free-surface PCL ringed spherulites was investigated by using atomic force microscopy. The spherulites were obtained by crystallization of PCL/PVC blends of different compositions. It was found that the ringed spherulite exhibited regularly fluctuating rings on its surface. Compared with the bright-dark ring pattern of the spherulite under a polarizing microscope, it was proved that the optical characteristics of the ringed spherulite under polarizing microscope coincided with its surface characteristics. The bright rings in polarizing micrographs of the spherulite coincided with the convex rings on its surface, while the dark rings coincided with the concave rings.

Phase field modeling of the ring-banded spherulites of crystalline polymers: The role of thermal diffusion

The ring-banded spherulite is a special morphology of polymer crystals and has attracted considerable attention over recent decades. In this study, a new phase field model with polymer characteristics is established to investigate the emergence and formation mechanism of the ring-banded spherulites of crystalline polymers. The model consists of a nonconserved phase field representing the phase transition and a temperature field describing the diffusion of the released latent heat. The corresponding model parameters can be obtained from experimentally accessible material parameters.Two-dimensional calculations are carried out for the ring-banded spherulitic growth of polyethylene film under a series of crystallization temperatures. The results of these calculations demonstrate that the formation of ring-banded spherulites can be triggered by the self-generated thermal field. Moreover, some temperature-dependent characteristics of the ring-banded spherulites observed in experiments are reproduced by simulations, which may help to study the effects of crystallization temperature on the ring-banded structures.

ISOTHERMAL CRYSTALLIZATION BEHAVIOR AND UNIQUE BANDED SPHERULITES OF HYDROXYAPATITE/POLY(L-LACTIDE) NANOCOMPOSITES

Hydroxyapatite/poly（L-lactide） （HA/PLLA） nanocomposites were prepared by the solvent mixing method. The isothermal crystallization behavior was studied by differential scanning calorimetry （DSC） and polarized optical microscopy （POM）. The results show that the crystallization behavior of HA/PLLA composites was strongly affected by the content of HA and crystallization temperature, and the addition of HA could promote nucleation and enhance the crystallization rate. When isothermal crystallization was carried out at 110℃, the HA/PLLA nanocomposite with 1% HA content crystallized most rapidly among all the composites and the half crystallization time was only 1.0 min. Banded spherulites were observed for the HA/PLLA composites, but no banded spherulites were seen in the crystals of PLLA under the same condition.

Observation of banded spherulites and lamellar structures by atomic force microscopy

Lamellar structures of banded spherulites of poly(?caprolactone)/poly(vinyl chloride) (PCL/PVC) blends are observed using tapping mode atomic force microscopy (AFM). The surface of the PCL/PVC banded spherulites presents to be concentric periodic ups and downs. The period of the bands corresponds to the extinction rings under the polarized optical microscopy observa-tion. The lamellae with edge-on orientation in the ridges and the flat-on lamellae in the valleys of the banded spherulites are observed clearly. The twisting between the edge-on and flat-on lamel-lae is also observed.

The Banded Spherulites of iPP Induced by Pressure Vibration Injection Molding

Isotactic polypropylene（i PP） samples obtained by pressure vibration injection molding（PVIM） and conventional injection molding（CIM） were studied by polarized-light microscopy（PLM）, respectively. It was found that the alternating bright and dark banded spherulites were generated in the transitional region of PVIM parts. It is the first time that the banded spherulites of isotactic polypropylene were observed in polymer processing. What＇s more, the banded spherulites were proved to be constituted of α-form crystal by hot stage polarized-light microscopy（HT-PLM） and wide angle X-ray diffraction（WAXD）. Morphology of the banded spherulites was also studied by scaning electronical microscopy（SEM）.

Effects of solvents and temperature on spherulites of self-assembled phloroglucinol tristearate

Herein,phloroglucinol tristearate(PhgTS)was used to study the crystallization process due to its unique symmetric structure containing a benzene ring and three aliphatic chains.Spherulites of crystallized PhgTS from four solvents under diverse conditions were analyzed in detail and their formation process was studied.Maltese cross is shown by PhgTS spherulites obtained from aprotic solvents via polarized optical microscopy.In comparison,no Maltese cross can be observed from branch-like crystals formed from protic solvents.Independent on the micro-scaled morphology,lamellae were found to be the basic blocks constructing both PhgTS spherulites and branch-like crystals,which were formed predominantly by stacked PhgTS molecules.Although differential characters of the solvents did not affect the formation of lamellas,the solvents played a crucial role in the formation of self-assembled microscaled morphologies.In particular,the morphologies of spherulites were strongly affected by the concentration of PhgTS solutions,surrounding tempera-ture and evaporation rate of solvents.Generally,a higher concentration of PhgTS led to more homogeneous spherulites,a lower evaporation rate resulted in more compact spherulites,and a higher surounding temperature generated preferentially more ring-banded spherulites of PhgTS.

Texture Induced by Molecular Weight Dispersity: Polymorphism within Poly(L-lactic acid) Spherulites

Poly(L-lactic acid)(PLLA)has drawn much attention due to its excellent medical and pharmaceutical applications for decades.As a semi-crystalline polymer,morphology and crystal structure of PLLA greatly determine its properties.Here,w e demonstrate,for PLLA films,a nonconventional texture featuring two types of spherulites emerging in pairs to form a distinct nested structure where a small spherulite(〜10μm)is embedded in a large one(100μm to 300μm).In addition to the size,the molecular weight and polymorph are different in the large and small spherulites.Crystallographic a-form and relatively low molecular weight are identified in the large spherulites,while meta-stable a'-form and relatively high molecular weight in the small ones.These differences suggest that the polydisperse PLLA polymers fractionate during film formation and the high-molecular-weight fraction crystallizes into the small spherulites with meta-stable structure because of its complicated polymer entanglement and high viscosity.In contrast,the rest of polymers crystallize into the large spherulites with the thermodynamically stable polymorph.Furthermore,this texture exhibits accelerated PLLA degradation initiated from the small spherulites,which is distinct from the typical PLLA spherulites.Insights provided by this work may lead to new texture-properties relationship associated with polydispersity of molecular weight.

The Effect of Annealing Treatments on Spherulitic Morphology and Physical Ageing on Glass Transition of Poly Lactic Acid (PLLA)

Spherulitic morphology of pure poly lactic acid (PLLA) PLLA have investigated after thermal annealing. The morphology of spherulite of pure poly lactic acid (PLLA) PLLA have investigated after thermal annealing. The effect of both annealing temperature and crystallization temperature on the formation of cracks was described by polarized optical microscope (POM). Non banded spherulite (fibrils) with cracks was detected in PLLA film after annealing at 160°C (180 min.) and isothermal crystallization temperatures at 140°C and 150°C. With increasing temperature after annealing treatment the size of spherulite is increased and more cracks are formed. The maximum growth rate of spherulites was found at 130°C. The physical ageing was carried out by annealing the PLLA sample at room temperature for several annealing time (ta) from 0 h to 720 h. The enthalpy relaxation has been studied by differential scanning calorimetry (DSC) through analysis of the endothermic peak of glass transition temperature, which increased and shifted towards higher temperature as the annealing time increased.

MORPHOLOGY EVOLUTION IN PTFE AS A FUNCTION OF MELT TIME AND TEMPERATURE——Ⅱ.LOW MOLECULAR WEIGHT FOLDED CHAIN SINGLE CRYSTALS AND BAND STRUCTURES

The effect of sintering dispersed and bulk,low molecular weight(M_n=50,000 Da),nano-emulsionpolytetrafluoroethylene(PTFE)particles near their melting point is described.With the nascent particles consisting of ca.75 nm diameter,hexagonal,single crystals,sintering at,e.g.,350℃,results,initially,in merger of neighboring particles,followed by individual molecular motion on the substrate and the formation of folded chain,lamellar single crystals andspherulites,and on-edge ribbons.It is suggested these structures develop,with time,in the mesomorphic“melt”.Sintering ofthe bulk resin yields extended chain,band structures,as well as folded chain lamellae;end-surface to end-surface merger,possibly by end-to-end polymerization,occurs with increasing time.

Electrical and mechanical properties of vapour grown gallium monotelluride crystals

The physical vapour deposition （PVD） of gallium monotelluride （GaTe） in different crystalline habits was established in the growth ampoule, strongly depending on the temperature gradient. Proper control on the temperatures of source and growth zones in an indigenously fabricated dual zone furnace could yield the crystals in the form of whiskers and spherulites. Optical and electron microscopic images were examined to predict the growth mechanism of morphologies. The structural parameters of the grown spherulites were determined by X-ray powder diffraction （XRD）. The stoichiometric composition of these crystals was confirmed using energy dispersive analysis by X-rays （EDAX）. The type and nature of electrical conductivity were identified by the conventional hot probe and two probe methods, respectively. The mechanical parameters, such as Vickers microhardness, work hardening index, and yield strength, were deduced from microindentation measurements. The results show that the vapour grown p-GaTe crystals exhibit novel physical properties, which make them suitable for device applications.

Changes of crystallinity and spherulite morphology in isotactic polypropylene after rolling and heat treatment

The spherulite morphology of the rolled and subsequent heat-treated isotactic polypropylene （iPP） was observed by polarized microscopy, and the crystallinity evolution of materials was also measured by the wide angle X-ray scattering （WAXS）. Rolling led to the oblate spherulites in the deformed iPP samples. The sheared crystalline lamellae broke apart into sets of crystalline blocks during rolling. As a result, the crystallinity of the iPP samples was greatly reduced during deformation, which induced the unclear spherulites and spherulite boundaries. Subsequent heat treatment resulted in the strong reerystallization of the rolled iPP samples. But the recrystaUizatinn in this work only meant the rearrangement of the macromolecule along the unbroken crystalline lamellae and the existing small crystalline blocks in the deformed spherulites. Heat treatment did not change the shape of the spherulites formed during deformation. The recrystallization also resulted in very clear spherulites and spherulite boundaries.

CRYSTALLIZATION CHARACTERISTICS OF β-PHASE CRYSTALS IN COPOLYMERS OF POLYPROPYLENE WITH LOW ETHYLENE CONTENT

Polypropylene copolymers (CPP) containing β-nucleating agent were investigated by differential scanningcalorimetry (DSC), wide-angle X-ray diffraction (WAXD) and polarizing light microscopy (PLM). The results show thathigh content of β-phase crystals can also be formed for CPPs. Like PP homopolymers, the CPPs also have a most favorabletemperature near 132℃ for β-phase crystal growth. The crystallization rate of CPPs containing β-nucleating agent (β-CPP) ismuch greater than that of PP homopolymer containing β-nucleating agent (β-PP homopolymer). The observation ofspherulite morphology of β-CPP and β-PP homopolymer shows that the spherulites of β-CPP are more imperfect than thoseof β-PP homopolymer.

Synthesis and Structure of Butylene Terephthalate-ε-Caprolactone Copolyesters

A series of butylene terephthalate-E-caprolactone copolyesters (BCL) with different hard segment content were successfully synthesized and characterized by 1H-NMR. DSC. PLM and U viscometer, The sequence structure and crystallization characteristics of BCL copolyesters were carefully investigated.

MORPHOLOGY OF A THERMOTROPIC AROMATIC POLYESTER

The crystalline morphology of a thermotropic aromatic polyester has been studied by microscopy techniques. Spherulites with ringed structure under polarizing micioscope were observed for solution cast specimens, They were composed of radially growing crystalline lamellae of thickness around 100. It was found that the molecules were packed in the thickness direction. Banded texture was observed in randomly packed domains for melt cast specimens. The bands have the same width and internal structure as those usually observed in oriented specimens of these polymers obtained by shearing their mesomorphic melt.

POLYCAPROLACTAM MODIFIED BY POLYPHENYLQUINOXALINE

Three polycaprolactam samples modified by 0.05—0.50% polyphenylquinoxaline(PPQ)by weight were prepared.Their structure and mechanical properties were characterized by FT-IR, SEM, density, tensile, impact, DTAand visco-elastic method, PPQ induced the formation of 'crystal grains' distributed evenly over nylon spherulites in modified samples, which were observed for the first time, and strengthened modified samples. Modified nylons had higher crystallinities, higher T_g, more nearly perfect spherulites than MC nylon itself, and showed typical reinforcing effect on mechanical properties.

TIME-DEPENDENT MORPHOLOGY OF POLYETHYLENE-POLYPROPYLENE BLENDS

The effect of time-temperature treatment on morphology of polyethylene-polypropylene (PE-PP) blends wasstudied to establish a relationship between thermal history, morphology and mechanical properties. Polypropylene (PP)homopolymers were used to blend with various polyethylenes (PE), including high density polyethylene (HDPE), lowdensity polyethylene (LDPE), linear low density polyethylene (LLDPE), and very and ultra low density polyethylene(VLDPE and ULDPE). The majority of the blends were prepared at a ratio of PE:PP = 80:20, while blends of PP and LLDPEwere prepared at various compositions. Thermal treatment was carried out at temperatures between the crystallizationtemperatures of PP and PEs to allow PP to crystallize first from the blends. On cooling further, PE crystallized too. A verydiffuse PP spherulite morphology in the PE matrix was formed in some partially miscible blends when PP was less than 20%by mass. Droplet-matrix structures were developed in other blends with either PP or PE as dispersed domains in a continuousmatrix, depending on the composition ratio. The scanning electron microscopy (SEM) images displayed a fibrillar structureof PP spherulite in the LLDPE-PP (80:20) and large droplets of PP in the HDPE-PP (80:20) blend, providing larger surfacearea and better bonding in the LLDPE-PP (80:20) blends. This explains why the blends with diffuse spherulite morphologyshowed greater improvement in tensile properties than droplet-matrix morphology blends after time-temperature treatment.

PREPARATION AND MORPHOLOGY OF ISOTACTIC POLYPROPYLENE WITH HIGH CONTENT OF β CRYSTALLINE FORM

Isotactic polypropylene (iPP) with high content of ~ crystalline form was prepared by adding a series of new p form nucleators. The spherulites and morphology of//farm iPP (//-iPP) were investigated by wide-angle X-ray diffraction(WAXD), polarizing microscope (PLM), scanning electron microscope (SEM) and small-angle light scattering (SALS). WAXD experimental results indicate that the amount of p form in iPP (K_x) increases with increasing /~ nucleator content from zero to 0.07 wt% or crystallization temperature T_c from 20 to 120℃ and that the highest K_x value is up to 0.95. PLM observations suggest that p spherulites exhibit bright color and that their Maltese Crosses display some concentric banding of a rather spiky, jagged character. Their !amellae are smooth and relaxed layer-plate like structure by SEM and their SALS H_v patterns arc four-petalled.

Study of Spherulite Growth Rate and Morphology of Polypropylenebased Blends by Image Processing Technology

The method for measuring the spherulite growth rate and studying the morphology of polypropylene - based blends by image processing technology is described. The main advantages of this method, as compared to existing techniques, are: better reliability; reproducibility; ease of manipulation. Such an approach provides a means of measuring the rate of spherulite growth. In this study, isotactic polypropylene (PP), polystyrene (PS)/PP, and polybutylene terephthalate (PBT)/PP have been studied. The results show that the technology of image analysis is very useful in the study of the kinetics of crystallization of polymer.

CRYSTALLINE MORPHOLOGY IN A SERIES OF CH3-SUBSTITUTED THERMOTROPIC AROMATIC POLYESTERS WITH EVEN AND ODD FLEXIBLE SPACERS

Crystalline morphology in a series of CH3-substituted main chain thermotropic aromatic polyesters with even and odd numbered methylene spacers has been studied by polarizing optical microscopy (POM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). On crystallization from solution evaporation spherulites of radial structure were observed in the polymers with even numbered spacers, but spherulites with concentric rings form in the polymer with odd numbered spacers. Both spherulites have a lamellar structure, which is about 10 nm in thickness. On crystallization from nematic glassy state spherulites can not be grown; lamellar structure was only observed around disclinations in a specimen during crystallization. Ln the case of crystallization from nematic melt two types of spherulites can be observed far the sample with even numbered spacers. For the sample with add numbered spacers spherulites can not be formed, but only irregular crystallites.

Studies on the Crystallization Behavior of Polypropylene Solid Phase Grafted Maleic Anhydride

ＳｔｕｄｉｅｓｏｎｔｈｅＣｒｙｓｔａｌｌｉｚａｔｉｏｎＢｅｈａｖｉｏｒｏｆＰｏｌｙｐｒｏｐｙｌｅｎｅＳｏｌｉｄＰｈａｓｅＧｒａｆｔｅｄＭａｌｅｉｃＡｎｈｙｄｒｉｄｅＳｔｕｄｉｅｓｏｎｔｈｅＣｒｙｓｔａｌｌｉｚａｔｉｏｎＢｅｈａｖｉｏｒｏｆＰｏｌｙｐｒ...