Theoretical and Experimental Study on the Performance of Hermetic Diaphragm Squeeze Film Dampers for Gas-Lubricated Bearings

Low damping characteristics have always been a key sticking points in the development of gas bearings.The application of squeeze film dampers can significantly improve the damping performance of gas lubricated bearings.This paper proposed a novel hermetic diaphragm squeeze film damper(HDSFD)for oil-free turbomachinery supported by gas lubricated bearings.Several types of HDSFDs with symmetrical structure were proposed for good damping performance.By considering the compressibility of the damper fluid,based on hydraulic fluid mechanics theory,a dynamic model of HDSFDs under medium is proposed,which successfully reflects the frequency dependence of force coefficients.Based on the dynamic model,the effects of damper fluid viscosity,bulk modulus of damper fluid,thickness of damper fluid film and plunger thickness on the dynamic stiffness and damping of HDSFDs were analyzed.An experimental test rig was assembled and series of experimental studies on HDSFDs were conducted.The damper fluid transverse flow is added to the existing HDSFD concept,which aims to make the dynamic force coefficients independent of frequency.Although the force coefficient is still frequency dependent,the damping coefficient at high frequency excitation with damper fluid supply twice as that without damper fluid supply.The results serve as a benchmark for the calibration of analytical tools under development.

Genuine entanglement under squeezed generalized amplitude damping channels with memory

We study genuine entanglement among three qubits undergoing a noisy process that includes dissipation, squeezing,and decoherence. We obtain a general solution and analyze the asymptotic quantum states. We find that most of these asymptotic states can be genuinely entangled depending upon the parameters of the channel, memory parameter, and the parameters of the initial states. We study Greenberger–Horne–Zeilinger(GHZ) states and W states, mixed with white noise,and determine the conditions for them to be genuinely entangled at infinity. We find that for these mixtures, it is possible to start with a bi-separable state(with a specific mixture of white noise) and end with genuine entangled states. However, the memory parameter μ must be very high. We find that in contrast to the two-qubit case, none of the three-qubit asymptotic states for n → ∞ are genuinely entangled.

Squeeze casting for metal alloys and composites:An overview of influence of process parameters on mechanical properties and microstructure

Squeeze casting is a well-established and reliable process for fabricating high-integrity metallic alloys,bimetals,and composites.The quality and high performance of squeeze cast components are dependent on optimum casting conditions.Inappropriate selection of parameter values may adversely affect the quality of the casting.The squeeze cast components are generally subjected to secondary processing such as heat treatment,extrusion,and other bulk deformation processes to improve the microstructural features and mechanical properties.Heat treatment further refines the grains and reduces porosity,consequently improving tensile strength,and hardness;however,ductility decreases.This paper provides a comprehensive review on studies concerning the influence of processing parameters on porosity,density,percentage elongation,strength,hardness,wear,and fracture of squeeze casting alloys,aiming to provide sufficient information on the squeeze casting process and the effects of processing parameters on product quality.

A comparative study on Sn macrosegregation behavior of ternary Al-Sn-Cu alloys prepared by gravity casting and squeeze casting

A comprehensive study on Sn macrosegregation behavior in ternary Al-Sn-Cu alloys was carried out by comparative analysis between gravity casting and squeeze casting samples.The microstructure and Sn distribution of the castings were characterized by metallography,scanning electron microscopy(SEM),energy-dispersive X-ray(EDX)spectroscopy,and a direct reading spectrometer.Results show that there are obvious differences in Sn morphology between gravity casting and squeeze casting alloys.Under squeeze casting condition,the grain size of the casting is smaller and the distribution ofβ(Sn)is uniform.This effectively reduces the segregation of triangular grain boundary as well as the segregation of Sn.The segregation types of Sn in gravity casting and squeeze casting samples are obviously different.The upper surfaces of gravity casting samples show severe negative segregation,while all the lower surfaces have positive segregation.Compared with gravity casting,squeeze casting solidifies under isostatic pressure.Due to the direct contact between the upper surface of the casting and the mold,the casting solidifies faster under higher undercooling degree and pressure.Consequently,the uniform distribution of Sn reduces the segregation phenomenon on the surface of the casting.

Evaluation of microstructure and mechanical properties of squeeze overcast Al7075-Cu composite joints

Al7075-Cu composite joints were prepared by the squeeze overcast process.The effects of melt temperature,die temperature,and squeeze pressure on hardness and ultimate tensile strength(UTS)of squeeze overcast Al7075-Cu composite joints were studied.The experimental results depict that squeeze pressure is the most significant process parameter affecting the hardness and UTS.The optimal values of UTS(48 MPa)and hardness(76 HRB)are achieved at a melt temperature of 800℃,a die temperature of 250℃,and a squeeze pressure of 90 MPa.Scanning electron microscopy(SEM)shows that fractured surfaces show flatfaced morphology at the optimal experimental condition.Energy-dispersive spectroscopy(EDS)analysis depicts that the atomic weight percentage of Zn decreases with an increase in melt temperature and squeeze pressure.The optimal mechanical properties of the Al7075-Cu overcast joint were achieved at the Al2Cu eutectic phase due to the large number of copper atoms that dispersed into the aluminum melt during the solidification process and the formation of strong intermetallic bonds.Gray relational analysis integrated with the Taguchi method was used to develop an optimal set of control variables for multi-response parametric optimization.Confirmatory tests were performed to validate the effectiveness of the employed technique.The manufacturing of squeeze overcast Al7075-Cu composite joints at optimal process parameters delivers a great indication to acknowledge a new method for foundry practitioners to manufacture materials with superior mechanical properties.

Review of Design of Process Parameters for Squeeze Casting

Squeeze casting(SC)is an advanced net manufacturing process with many advantages for which the quality and properties of the manufactured parts depend strongly on the process parameters.Unfortunately,a universal efficient method for the determination of optimal process parameters is still unavailable.In view of the shortcomings and development needs of the current research methods for the setting of SC process parameters,by consulting and analyzing the recent research literature on SC process parameters and using the CiteSpace literature analysis software,manual reading and statistical analysis,the current state and characteristics of the research methods used for the determination of SC process parameters are summarized.The literature data show that the number of pub-lications in the literature related to the design of SC process parameters generally trends upward albeit with signifi-cant fluctuations.Analysis of the research focus shows that both“mechanical properties”and“microstructure”are the two main subjects in the studies of SC process parameters.With regard to materials,aluminum alloys have been extensively studied.Five methods have been used to obtain SC process parameters:Physical experiments,numeri-cal simulation,modeling optimization,formula calculation,and the use of empirical values.Physical experiments are the main research methods.The main methods for designing SC process parameters are divided into three categories:Fully experimental methods,optimization methods that involve modeling based on experimental data,and theoreti-cal calculation methods that involve establishing an analytical formula.The research characteristics and shortcomings of each method were analyzed.Numerical simulations and model-based optimization have become the new required methods.Considering the development needs and data-driven trends of the SC process,suggestions for the develop-ment of SC process parameter research have been proposed.

Effects of macrosegregation on mechanical and tribological properties of squeeze casting immiscible bearing alloys

The macrosegregation behaviors of Al-Sn-Cu ternary immiscible alloy castings and their effects on mechanical and tribological properties were investigated.The results demonstrate that Sn and Cu segregate in the casting simultaneously,and the mass fraction of the two elements has a"U"shaped distribution.Significantly,positive and negative segregation occur in the casting,with positive segregation appearing on the top and lower surfaces and negative segregation on the remaining surfaces,with the 1/2 surface(hot node location)having the highest degree of negative segregation.Furthermore,the results of Vickers hardness,tensile strength,and elongation show that Sn and Cu cooperatively affect the mechanical properties of castings.The higher the mass fraction of Sn and Cu elements,the higher the hardness,the greater the tensile strength,and the better the elongation.The findings of the step-by-step loading tests demonstrate that the segregation of Sn and Cu significantly impacts the tribological characteristics of the castings.The higher the mass fraction of Sn and Cu on the sample surface,the better the tribological characteristics.

Performance optimization on finite-time quantum Carnot engines and refrigerators based on spin-1/2 systems driven by a squeezed reservoir

We investigate the finite-time performance of a quantum endoreversible Carnot engine cycle and its inverse operation-Carnot refrigeration cycle,employing a spin-1/2 system as the working substance.The thermal machine is alternatively driven by a hot boson bath of inverse temperatureβ_(h)and a cold boson bath at inverse temperatureβ_(c)(>βh).While for the engine model the hot bath is constructed to be squeezed,in the refrigeration cycle the cold bath is established to be squeezed,with squeezing parameter r.We obtain the analytical expressions for both efficiency and power in heat engines and for coefficient of performance and cooling rate in refrigerators.We find that,in the high-temperature limit,the efficiency at maximum power is bounded by the analytical valueη_(+)=√sech(2r)(1-η_(C)),and the coefficient of performance at the maximum figure of merit is limited byε_(+)=√sech(2r)(1+ε_(C))/sech(2r)(1+ε_(C))-εC)-1,whereη_(C)=1-β_(h)/β_(c)andε_(C)=β_(h)/(β_(c)-β_(h))are the respective Carnot values of the engines and refrigerators.These analytical results are identical to those obtained from the Carnot engines based on harmonic systems,indicating that the efficiency at maximum power and coefficient at maximum figure of merit are independent of the working substance.

Squeezed state generation using cryogenic InP HEMT nonlinearity

This study focuses on generating and manipulating squeezed states with two external oscillators coupled by an InP HEMT operating at cryogenic temperatures.First,the small-signal nonlinear model of the transistor at high frequency at 5 K is analyzed using quantum theory,and the related Lagrangian is theoretically derived.Subsequently,the total quantum Hamiltonian of the system is derived using Legendre transformation.The Hamiltonian of the system includes linear and nonlinear terms by which the effects on the time evolution of the states are studied.The main result shows that the squeezed state can be generated owing to the transistor’s nonlinearity;more importantly,it can be manipulated by some specific terms introduced in the nonlinear Hamiltonian.In fact,the nonlinearity of the transistors induces some effects,such as capacitance,inductance,and second-order transconductance,by which the properties of the external oscillators are changed.These changes may lead to squeezing or manipulating the parameters related to squeezing in the oscillators.In addition,it is theoretically derived that the circuit can generate two-mode squeezing.Finally,second-order correlation(photon counting statistics)is studied,and the results demonstrate that the designed circuit exhibits antibunching,where the quadrature operator shows squeezing behavior.

Preparation of squeezed light with low average photon number based on dynamic Casimir effect

It is well known that squeezed states can be produced by nonlinear optical processes,such as parametric amplification and four wave mixing,in which two photons are created or annihilated simultaneously.Since the Hamiltonian of the dynamic Casimir effect contains a~2 and a~(+2),photons in such a process are also generated or annihilated in pairs.Here we propose to get squeezed light through the dynamic Casimir effect.Specifically,we demonstrate it from the full quantum perspective and the semiclassical perspective successively.Different from previous work,we focus on generating squeezed states with the lowest average photon number,because such squeezed states have better quantum properties.For the full quantum picture,that is,phonons also have quantum properties,when the system is initially in the excited state of phonons,squeezed light cannot be generated during the evolution,but the light field can collapse to the squeezed state by measuring the state of phonons.When the phonon is treated as a classical quantity,that is,the cavity wall is continuously driven,squeezed light with the minimum average photon number will be generated in the case of off-resonance.This will play a positive role in better regulating the photon state generated by the dynamic Casimir system in the future.

Quantum-enhanced optical precision measurement assisted by low-frequency squeezed vacuum states

Stable low-frequency squeezed vacuum states at a wavelength of 1550 nm were generated.By controlling the squeezing angle of the squeezed vacuum states,two types of low-frequency quadrature-phase squeezed vacuum states and quadrature-amplitude squeezed vacuum states were obtained using one setup respectively.A quantum-enhanced fiber Mach–Zehnder interferometer(FMZI)was demonstrated for low-frequency phase measurement using the generated quadrature-phase squeezed vacuum states that were injected.When phase modulation was measured with the quantumenhanced FMZI,there were above 3 dB quantum improvements beyond the shot-noise limit(SNL)from 40 kHz to 200 kHz,and 2.3 dB quantum improvement beyond the SNL at 20 kHz was obtained.The generated quadrature-amplitude squeezed vacuum state was applied to perform low-frequency amplitude modulation measurement for sensitivity beyond the SNL based on optical fiber construction.There were about 2 dB quantum improvements beyond the SNL from 60 kHz to 200 kHz.The current scheme proves that quantum-enhanced fiber-based sensors are feasible and have potential applications in high-precision measurements based on fiber,particularly in the low-frequency range.

Quantum speed limit of a single atom in a squeezed optical cavity mode

We theoretically study the quantum speed limit of a single atom trapped in a Fabry-Perot microresonator.The cavity mode will be squeezed when a driving laser is applied to the second-order nonlinear medium,and the effective Hamiltonian can be obtained under the Bogoliubov squeezing transformation.The analytical expression of the evolved atom state can be obtained by using the non-Hermitian Schr¨odinger equation for the initial excited state,and the quantum speed limit time coincides very well for both the analytical expression and the master equation method.From the perspective of quantum speed limit,it is more conducive to accelerate the evolution of the quantum state for the large detuning,strong driving,and coupling strength.For the case of the initial superposition state,the form of the initial state has more influence on the evolution speed.The quantum speed limit time is not only dependent on the system parameters but also determined by the initial state.

Time evolution of a squeezed chaotic field in an amplitude damping channel when used as a generating field for a squeezed number state

We investigate how an optical squeezed chaotic field（SCF） evolves in an amplitude dissipation channel. We have used the integration within ordered product of operators technique to derive its evolution law. We also show that the density operator of SCF can be viewed as a generating field of the squeezed number state.

The state of the art in scale inhibitor squeeze treatment

The mechanistic understanding of the reactions that govern the inhibitor retention and release,modeling,and the state-ofthe-art innovation in squeeze treatment are reviewed.The retention and release are governed by(1)the amount of calcite that can dissolve prior to inhibitor-induced surface poisoning;(2)calcite surface poisoning after^20 molecular layers of surface coverage by the adsorbed inhibitors to retard further calcite dissolution;(3)less base,CO3^2-,is released into the aqueous solution;(4)formation of the more acidic inhibitor precipitates;(5)phase transformation and maturation of the more acidic inhibitor precipitates;and(6)dissolution of the less soluble crystalline inhibitor precipitates.The trend to advance squeeze technologies is through(1)enhancing scale inhibitor retention,(2)optimizing the delivery of scale inhibitors to the target zone,and(3)improving monitoring methods.Lastly,a prototype yardstick for measuring the squeeze performance is used to compare the squeeze life of 17 actual squeeze treatments.Even though the various squeeze treatments appear to be different.all published squeeze durations can be rated based on the normalized squeeze life per unit mass of inhibitors.

Mechanism and application of a newly developed pressure casting process:horizontal squeeze casting

Compared to traditional high-pressure die casting(HPDC),horizontal squeeze casting(HSC)is a more promising way to fabricate high-integrity castings,owing to a reduced number of gas and shrinkage porosities produced in the casting.In this paper,the differences between HSC and HPDC are assessed,through which it is shown that the cavity filling velocity and the size of the gating system to be the most notable differences.Equipment development and related applications are also reviewed.Furthermore,numerical simulation is used to analyze the three fundamental characteristics of HSC:slow cavity filling,squeeze feeding and slow sleeve filling.From this,a selection principle is given based on the three related critical casting parameters:cavity filling velocity,gate size and sleeve filling velocity.Finally,two specific applications of HSC are introduced,and the future direction of HSC development is discussed.

Squeeze-swapping by Bell measurement studied in terms of the entangled state representation

By virtue of the entangled state representation （Hong-Yi Fan and J R Klauder 1994 Phys. Rev. A 49 704） and the two-mode squeezing operator＇s natural representation （Hong-Yi Fan and Yue Fan 1996 Phys. Rev. A 54 958） we propose the squeeze-swapping mechanism which can generate quantum entanglement and new squeezed states of continuum variables.

Research progress on squeeze casting in China

Squeeze casting is a technology with short route,high efficiency and precise forming,possessing features of casting and plastic processing.It is widely used to produce high performance metallic structural parts.As energy conservation and environmental protection concerns have risen,lightweight and high performance metal parts are urgently needed,which accelerated the development of squeeze casting technology over the past two decades in China.In this paper,research progress on squeeze casting alloys,typical parts manufacturing and development of squeeze casting equipment in China are introduced.The future trend and development priorities of squeeze casting are discussed.

Effect of heat treatment on microstructure and properties of semi-solid squeeze casting AZ91D

Semi-solid AZ91D magnesium alloy billets were prepared by near-liquidus heat holding.Semi-solid squeeze casting was conducted at 575,585 and 595℃,respectively,with 1 mm·s^-1 squeeze speed.The semisolid squeeze casting AZ91D samples were heat treated by T4(solution at 415℃for 24 h)and T6(solution at 415℃for 24 h+220℃for 8 h)processes,respectively.The microstructure and mechanical properties of the alloy in different states were investigated by means of OM,SEM and tensile testing machine.The results show that compared to as-cast alloy,the grain size of the semi-solid squeezed AZ91D decreased significantly,and with the increase of semi-solid squeeze temperature,the grain size of AZ91D increased.The grains of the alloy were refined by T4 treatment,and further refined by T6 treatment.T6 treatment greatly improved the tensile strength,elongation,and hardness,but did not significantly improve yield strength.After 575℃squeeze casting and T6 treatment,the ultimate tensile strength(UTS)reached 285 MPa,the elongation reached 13.36%,and the hardness also reached the maximum(106.8 HV),but the yield strength(YS)was only 180 MPa.During the process of semi-solid squeeze casting and heat treatment,the matrix grain was refined and a large number of precipitated and secondary precipitated phases of Mg17Al12 appeared.Both the average size of matrix grain and secondary precipitated phase decreased,while the volume fraction of secondary precipitated phase increased.All these resulted in high tensile strength,elongation and hardness.

Evaluation of the mold-filling ability of alloy melt in squeeze casting

The mold-filling ability of alloy mclt in squceze casting process was evaluated by means of the maximum length of Archimedes spiral line. A theoretical evaluating model to predict the maximum filling length was built based on the flowing theory of the incompressible viscous fluid. It was proved by experiments and calculations that the mold-tilling pressure and velocity are prominent influencing factors on the mold-filling ability of alloy melt. The mold-filling ability increases with the increase of the mold-filling pressure and the decrease of the proper mold-filling velocity. Moreover, the pouring temperature relatively has less effect on the mold-filling ability under the experimental conditions. The maximum deviation of theoretical calculating values with experimental results is less than 15%. The model can quantitatively estimate the effect of every factor on the mold-filling ability.

Bearing behavior and failure mechanism of squeezed branch piles

The current practice for the design of squeezed branch piles is mainly based on the calculated bearing capacity of circular piles. Insufficient considerations of the load-transfer mechanism, branch effect and failure mechanism, as well as overreliance on pile load tests, have led to conservative designs and limited application. This study performs full-scale field load tests on instrumented squeezed branch piles and shows that the shaft force curves have obvious drop steps at the branch position, indicating that the branches can effectively share the pile top load. The effects of branch position, spacing, number and diameter on the pile bearing capacity are analyzed numerically. The numerical results indicate that the squeezed branch piles have two types of failure mechanisms, i.e. individual branch failure mechanism and cylindrical failure mechanism. Further research should focus on the development of the calculation method to determine the bearing capacities of squeezed branch piles considering these two failure mechanisms.