This paper proposed a new diagnosis model for the stator inter-turn short circuit fault in synchronous generators.Different from the past methods focused on the current or voltage signals to diagnose the electrical fa...This paper proposed a new diagnosis model for the stator inter-turn short circuit fault in synchronous generators.Different from the past methods focused on the current or voltage signals to diagnose the electrical fault,the sta-tor vibration signal analysis based on ACMD(adaptive chirp mode decomposition)and DEO3S(demodulation energy operator of symmetrical differencing)was adopted to extract the fault feature.Firstly,FT(Fourier trans-form)is applied to the vibration signal to obtain the instantaneous frequency,and PE(permutation entropy)is calculated to select the proper weighting coefficients.Then,the signal is decomposed by ACMD,with the instan-taneous frequency and weighting coefficient acquired in the former step to obtain the optimal mode.Finally,DEO3S is operated to get the envelope spectrum which is able to strengthen the characteristic frequencies of the stator inter-turn short circuit fault.The study on the simulating signal and the real experiment data indicates the effectiveness of the proposed method for the stator inter-turn short circuit fault in synchronous generators.In addition,the comparison with other methods shows the superiority of the proposed model.展开更多
The quality of the stator winding coil directly affects the performance of the motor.A dual-camera online machine vision detection method to detect whether the coil leads and winding regions were qualified was designe...The quality of the stator winding coil directly affects the performance of the motor.A dual-camera online machine vision detection method to detect whether the coil leads and winding regions were qualified was designed.A vision detection platform was designed to capture individual winding images,and an image processing algorithm was used for image pre-processing,template matching and positioning of the coil lead area to set up a coordinate system.After eliminating image noise by Blob analysis,the improved Canny algorithm was used to detect the location of the coil lead paint stripped region,and the time was reduced by about half compared to the Canny algorithm.The coil winding region was trained with the ShuffleNet V2-YOLOv5s model for the dataset,and the detect file was converted to the Open Neural Network Exchange(ONNX)model for the detection of winding cross features with an average accuracy of 99.0%.The software interface of the detection system was designed to perform qualified discrimination tests on the workpieces,and the detection data were recorded and statistically analyzed.The results showed that the stator winding coil qualified discrimination accuracy reached 96.2%,and the average detection time of a single workpiece was about 300 ms,while YOLOv5s took less than 30 ms.展开更多
Based on the 6-pole outer stator(armature winding-stator),the influence of inner(permanent magnet-stator)/outer stator pole ratio n(n=NIS/NOS),stator relative positions and rotor pole number combinations on electromag...Based on the 6-pole outer stator(armature winding-stator),the influence of inner(permanent magnet-stator)/outer stator pole ratio n(n=NIS/NOS),stator relative positions and rotor pole number combinations on electromagnetic performance of partitioned stator switched flux permanent magnet(PM)machines(PS-SFPMMs)is investigated in this paper.Since the armature windings and PMs are located in two separated stators and PMs are stationary,PS-SFPMMs have high fault tolerance capabilities.To maximize the torque performance,the PM of inner stator pole should be aligned with outer stator pole when n is odd while the iron rib of inner stator pole should be aligned with outer stator pole when n is even.No matter what n is selected,the rotor pole number NR can be any integers except the phase number and its multiples.The analysis results indicate that the optimal NR is closed to(NIS+NOS)/2 and it is odd when n is odd while it is even when n is even.Meanwhile,symmetrical phase back-EMF waveform will be obtained when the ratio of Min(NOS,NIS)to the greatest common divisor of Min(NOS,NIS)and NR is even.Based on the optimal rotor pole numbers for 6-pole outer stator with different n and corresponding optimal relative position together with same rated copper loss,the average torque is improved by 18.4%,25.1%and 25.7%respectively in PS-SFPMMs with n equal to 2,3 and 4 when compared with PS-SFPMM with n equal to 1.The analyses are validated by experiment results of the prototype machine.展开更多
This paper analyzes dynamic equivalent circuit of induction motor and the relationship among inner fluxes, then presents a direct stator flux oriented continuous torque control (DSFOCTC) scheme of induction motor , wh...This paper analyzes dynamic equivalent circuit of induction motor and the relationship among inner fluxes, then presents a direct stator flux oriented continuous torque control (DSFOCTC) scheme of induction motor , which uses stator current vector control instead of voltage vector control. As a combination of direct torque control (DTC) and flux oriented vector control, it achieves round stator flux and continuous dynamic torque control resulting in less torque ripple than that in DTC. It reduces the dependence on rotor parameters, and is especially insensitive to rotor resistance. Finally, an induction motor speed control system incorporating this novel scheme is given and checked by simulation.展开更多
The resonances of parametric vibration with forced vibration isanalyzed, the bifurca- tion equation of the system is obtained andthe singularity analysis is made. Some of the laws and phe- nomenaare revealed. The tran...The resonances of parametric vibration with forced vibration isanalyzed, the bifurca- tion equation of the system is obtained andthe singularity analysis is made. Some of the laws and phe- nomenaare revealed. The transition variety and bifurcation diagram of thephysical parameteric plane are given. the results can be used inengineering.展开更多
With application of the lock-up clutch in the torque converter(TC), fuel economy is not much determined by its high-speed ratio transmission efficiency. As a benefit, more researches are focused on its low-speed rat...With application of the lock-up clutch in the torque converter(TC), fuel economy is not much determined by its high-speed ratio transmission efficiency. As a benefit, more researches are focused on its low-speed ratio performance so as to improve vehicle gradeability and launching acceleration performance. According to the results of computational fluid dynamics(CFD) analysis, hydrodynamic loss inside the stator cascade accounts for 42% of the total energy loss at stalling speed ratio. It is found that upstream flow with large impingement angle results in boundary layer separation at the leading edge, which aggregates hydrodynamic loss and decreases circular flow rate dramatically at low-speed ratio. In this paper, a dual-blade stator is proposed to suppress the boundary layer separation, which is parameterized by using the non-uniform rational B spline(NURBS) method. The mean camber line and blade profile curve are expressed by a three control points quadratic open NURBS and a cubic closed one respectively. The key design parameters included the slot width and suction side shape of the primary blade are analyzed. The most effective slot width is found to be between 4% and 8% chord length, and the boundary layer separation can be suppressed completely by decreasing distribution of momentum moment at the primary blade and adding it to the leading edge of the secondary blade. As a result, circular flow rate and impeller torque capacity is increased by 17.9% and 9.6% respectively at stalling speed ratio, meanwhile, low-speed ratio efficiency is also improved. Maximum efficiency at high-speed ratio decreases by 0.5%, which can be ignored as the work of lock-up clutch. This research focuses on using the dual-blade stator to optimize low-speed ratio performance of the TC, which is benefit to vehicle power performance.展开更多
Rotor–stator reactor(RSR), an efficient mass transfer enhancer, has been applied in many fields. However,the hydrodynamic characteristics of liquid flow in RSR are still a mystery despite they are fundamental for the...Rotor–stator reactor(RSR), an efficient mass transfer enhancer, has been applied in many fields. However,the hydrodynamic characteristics of liquid flow in RSR are still a mystery despite they are fundamental for the mass transfer performance and processing capacity. In view of the above, this paper studies the liquid–liquid flow and liquid holdup in RSR under various conditions with a high-speed camera. The paper firstly demonstrates two flow patterns and liquid holdup patterns that we obtained from our experiment and then presents in succession a flow pattern and a liquid holdup criterion for the transition of film flow to filament flow and complete filling to incomplete filling. It is found that experimental parameters, including rotor–stator distance, rotational speed and volume flow rate exert great influence on the average droplet diameter and size distribution. Besides, by comparison and contrast, we also find that the experimental values match well with our previous predicted calculations of the average diameter, and the relation between the average diameter and the mean energy dissipation rate.展开更多
The research object used in the dissertation was screw pump, which was widely applied in engineering field. The analysis of end face profile formation was completed on its main working components, i.e., rotor and stat...The research object used in the dissertation was screw pump, which was widely applied in engineering field. The analysis of end face profile formation was completed on its main working components, i.e., rotor and stator. With the purpose of finding optimal parameters to improve the efficiency of screw pump design, the key technologies involved in the parametric modeling of rotor and stator were analyzed. The three-dimensional (3D) design software SolidWorks was used for the secondary development and parametric modeling of rotor and stator. After that the simulation models of different kinds of screw pumps were established based on the cycloid type, variation coefficient, and screw head number. Finally the COSMOSMotion was used to analyze the motion characteristics on the equidistant line of rotor, including velocity and acceleration. This design and modeling method has been used in screw pump enterprises for design and development, laying the foundation for finite element analysis and further optimization of screw pump.展开更多
Presents the mathematic model built for double stator permanent magnet synchronous motors through a brief analysis of their future development, and the equations established for calculation of their torques, and the d...Presents the mathematic model built for double stator permanent magnet synchronous motors through a brief analysis of their future development, and the equations established for calculation of their torques, and the development of prototypes, and discusses the comparison of the motor under development with the conventional motors with the same volume, stator structure, and magnet shape, and concludes the motor under development is one of the ways to improve the performance/volume ratio of motors.展开更多
With the development of aviation electrification,higher demands for electrical machines are put forward in aircraft electric propulsion systems.The aircraft electric propulsion requirements and propulsion motor featur...With the development of aviation electrification,higher demands for electrical machines are put forward in aircraft electric propulsion systems.The aircraft electric propulsion requirements and propulsion motor features are analyzed in this paper.Comparing with conventional PM machines,ironless stator axial flux permanent magnet(AFPM)machine topologies with Litz wire windings allow designs with higher compactness,lightness and efficiency,which are suitable for high-frequency and high-power density applications.Based on the motor requirements and constraints of aircraft electric propulsion systems,this paper investigates a high-power 1 MW multi-stack ironless stator AFPM machine,which is composed of four 250kW modular motors by stacking in axial.The design guidelines and special attentions are presented,in term of electromagnetic,thermal,and mechanical performance for the high-frequency coils and Halbach-array PM rotor.Finally,an ironless stator AFPM motor is manufactured,tested and evaluated with the consideration of cost and processing cycle.The results show that the output power is up to 53.8kW with 95%efficiency at 9000r/min at this stage.The proposed ironless stator AFPM machine with oil immersed forced cooling proves to be a favorable candidate for application in electric aircraft as propulsion motors.展开更多
The suppressing design of the engine nacelle in an aircraft can benefit from the development of the prediction system for the sound fields in engine ducts which includes the prediction of the source generation and tha...The suppressing design of the engine nacelle in an aircraft can benefit from the development of the prediction system for the sound fields in engine ducts which includes the prediction of the source generation and that of sound propagation in ducts. First, the acoustic match mode principle between the source modes of rotor stator interaction noise and the propagation modes is presented in this paper. Second, by utilizing this principle, the theoretical prediction method for rotor stator interaction noise generation and its propagation and attenuation in an annular duct with multi treatments is developed. That means that the prediction of sound propagation and attenuation in the segmented ducts might no longer completely depend on the in duct mode measurements, and the investigation on the sound propagation and attenuation in ducts can be accomplished not only by acoustic mode measurement, but also by making use of the source prediction to determine the source modes excited by rotor stator interaction. The effects of fan speed, blade/vane numbers, axial spacing between rotor and stator on the in duct sound attenuation and generated sound power level before and after ducts (also including the sound power level of blade passing frequency and its harmonics at the inlet of ducts) have been numerically calculated by using this prediction method. The reliability of this prediction method is verified by reasonable agreement between the predicted results with measured results in references. By analyzing the results of calculating cases, some reference criteria are provided for the engineering design of the suppressing engine nacelle.展开更多
The stator flux and electromagnetic torque observation is the basis of direct torque controlled permanent magnet synchronous motor( PMSM) drive system. However,the traditional stator flux observer based on voltage mod...The stator flux and electromagnetic torque observation is the basis of direct torque controlled permanent magnet synchronous motor( PMSM) drive system. However,the traditional stator flux observer based on voltage model is affected by integral initial values and integral drift,that based on current model is affected by the parameters of PMSM,so a new stator flux observation method is proposed based on an improved secondorder generalized integrator( SOGI). Compared to the stator flux observation method based on the conventional SOGI,the proposed method can not only overcome the influence of integral initial values and integral drift,but also completely eliminate the DC offset's influence. Therefore,the observation accuracy of stator flux is further improved. The simulation and experimental results both show that the proposed method has a higher stator flux and electromagnetic torque observation precision.展开更多
Rotor vibration characteristics are first analyzed, which are that the rotor vibration of fundamental frequency will increase due to rotor winding inter-turn short circuit fault, air-gap dynamic eccentricity fault, or...Rotor vibration characteristics are first analyzed, which are that the rotor vibration of fundamental frequency will increase due to rotor winding inter-turn short circuit fault, air-gap dynamic eccentricity fault, or imbalance fault, and the vibration of the second frequency will increase when the air-gap static eccentricity fault occurs. Next, the characteristics of the stator winding parallel branches circulating current are analyzed, which are that the second harmonics circulating current will increase when the rotor winding inter-turn short circuit fault occurs, and the fundamental circulating current will increase when the air-gap eccentricity fault occurs, neither being strongly affected by the imbalance fault. Considering the differences of the rotor vibration and circulating current characteristics caused by different rotor faults, a method of generator vibration fault diagnosis, based on rotor vibration and circulating current characteristics, is developed. Finally, the rotor vibration and circulating current of a type SDF-9 generator is measured in the laboratory to verify the theoretical analysis presented above.展开更多
A novel cooling system with cooling channels is proposed for the stator of 3MW wind-driven generator.An experimental platform is built to investigate the performance of the cooling system with different loads.At30%,50...A novel cooling system with cooling channels is proposed for the stator of 3MW wind-driven generator.An experimental platform is built to investigate the performance of the cooling system with different loads.At30%,50% or 80% generator loads,the temperatures meet the design requirement.However,it is a little over the requirement at 100%load,duo to experimental errors and some unknown thermal resistances.In the test at 100%load,the developing trends of the parameters of these two generators are similar and only minor differences occurs when they reach steady state our work can be benefit for the design and improvement of MW wind-driven generator cooling solutions.展开更多
In large-scale electric machines, unbalanced magnetic pull (UMP) caused by eccentricity usually results in stator-rotor rub, so it is necessary to investigate the amplitude and the influencing factors. This paper ta...In large-scale electric machines, unbalanced magnetic pull (UMP) caused by eccentricity usually results in stator-rotor rub, so it is necessary to investigate the amplitude and the influencing factors. This paper takes the squirrel-cage induction motor as an example. A magnetic loop model of an induction motor is established by an analytical method. The impact of stator winding setup (parallel branch and pole pairs) on each magnetomotive force (MMF) and unbalanced magnetic pull is analyzed. Using the finite element simulation method, the spatial and time distribution of flux density of the rotor outer circle under static eccentricity is obtained, and the unbalanced magnetic pull calculation caused by static eccentricity is completed. The conclusion of the influence of stator winding on the size of unbalanced magnetic pull provides reliable gist for motor noise and vibration analysis, and especially provides an important reference for large induction motor design.展开更多
A new design of stato magnetic System is Proposed for 3-phase & 12-pole HB stepper, and it features bet-ter distribution of magntic lield to incare Pullou tope and bopmve Operaonal stability of moor and minimummut...A new design of stato magnetic System is Proposed for 3-phase & 12-pole HB stepper, and it features bet-ter distribution of magntic lield to incare Pullou tope and bopmve Operaonal stability of moor and minimummutual inductance between phase windimp to make design of control circuit easier, and application proved it is as good as expected.展开更多
The breakdown voltage plays an important role in evaluating residual life of stator insulation in generator.In this paper,we discussed BP neural network that was used to predict the breakdown voltage of stator insulat...The breakdown voltage plays an important role in evaluating residual life of stator insulation in generator.In this paper,we discussed BP neural network that was used to predict the breakdown voltage of stator insulation in generator of 300MW/18kV.At first the neural network has been trained by the samples that include the varieties of dielectric loss factor tanδ,the partial discharge parameters and breakdown voltage.Then we tried to predict the breakdown voltage of samples and stator insulations subjected to multi-stress aging by the trained neural network.We found that it's feasible and accurate to predict the voltage.This method can be applied to predict breakdown voltage of other generators which have the same insulation structure and material.展开更多
A double-shell model of hydroelectric-generator stator system was established. Applying the theory of mechano-electric analytical dynamics theory, the nonlinear vibration equation of magnetism and solid coupling of hy...A double-shell model of hydroelectric-generator stator system was established. Applying the theory of mechano-electric analytical dynamics theory, the nonlinear vibration equation of magnetism and solid coupling of hydroelectric-generator stator system, under steadily balanced three-phases operating condition, was obtained. According to the method of multiple scales for nonlinear oscillations, the double resonances of magnetism and solid coupling of hydroelectric-generator stater system, were investigated. It is pointed out that the system has abundant dynamics phenomenon including the attendant jumps and coexistence of multiple stable motions.展开更多
Quick detection of a small initial fault is important for an induction motor to prevent a consequent large fault.The mathematical model with basic motor equations among voltages,currents,and fluxes is analyzed and the...Quick detection of a small initial fault is important for an induction motor to prevent a consequent large fault.The mathematical model with basic motor equations among voltages,currents,and fluxes is analyzed and the motor model equations are described.The fault related features are extracted.An immune memory dynamic clonal strategy(IMDCS)system is applied to detecting the stator faults of induction motor.Four features are obtained from the induction motor,and then these features are given to the IMDCS system.After the motor condition has been learned by the IMDCS system,the memory set obtained in the training stage can be used to detect any fault.The proposed method is experimentally implemented on the induction motor,and the experimental results show the applicability and effectiveness of the proposed method to the diagnosis of stator winding turn faults in induction motors.展开更多
One of the solutions to reduce fuel consumption of diesel generators (DG) is to adapt the rotational speed to mechanical torque of the crankshaft. When load power decreases, a reduction in both mechanical torque and r...One of the solutions to reduce fuel consumption of diesel generators (DG) is to adapt the rotational speed to mechanical torque of the crankshaft. When load power decreases, a reduction in both mechanical torque and rotational speed of the diesel engine will maintain the combustion efficiency near the levels of the nominal regime. Accordingly, the generator itself should operate at a variable speed which normally requires power electronics converters. In this paper, we are exploring a new generator concept that uses a stator rotating in opposite direction to the rotor such as the relative velocity between the two components remains constant when diesel engine slows down. The stator itself is driven by a compensator synchronous motor (CM) such as the relative velocity of the rotor is constant, eliminating as such sophisticated power electronics. The model developed for the synchronous machine with a rotating stator is based on Park’s transformation. This new concept was modelled using MATLAB software. Experimental analysis has been conducted using a 500-kW diesel GENSET equipped with a permanent magnet synchronous generator (PMSG). The numerical and experimental results are in good agreement and demonstrate that fuel consumption is reduced with a rotating-mode stator for PMSG during low electrical loads.展开更多
基金supported in part by the National Natural Science Foundation of China(52177042)Natural Science Foundation of Hebei Province(E2020502031)+1 种基金the Fundamental Research Funds for the Central Universities(2017MS151),Suzhou Social Developing Innovation Project of Science and Technology(SS202134)the Top Youth Talent Support Program of Hebei Province([2018]-27).
文摘This paper proposed a new diagnosis model for the stator inter-turn short circuit fault in synchronous generators.Different from the past methods focused on the current or voltage signals to diagnose the electrical fault,the sta-tor vibration signal analysis based on ACMD(adaptive chirp mode decomposition)and DEO3S(demodulation energy operator of symmetrical differencing)was adopted to extract the fault feature.Firstly,FT(Fourier trans-form)is applied to the vibration signal to obtain the instantaneous frequency,and PE(permutation entropy)is calculated to select the proper weighting coefficients.Then,the signal is decomposed by ACMD,with the instan-taneous frequency and weighting coefficient acquired in the former step to obtain the optimal mode.Finally,DEO3S is operated to get the envelope spectrum which is able to strengthen the characteristic frequencies of the stator inter-turn short circuit fault.The study on the simulating signal and the real experiment data indicates the effectiveness of the proposed method for the stator inter-turn short circuit fault in synchronous generators.In addition,the comparison with other methods shows the superiority of the proposed model.
基金National Natural Science Foundation of China(No.U1831123)。
文摘The quality of the stator winding coil directly affects the performance of the motor.A dual-camera online machine vision detection method to detect whether the coil leads and winding regions were qualified was designed.A vision detection platform was designed to capture individual winding images,and an image processing algorithm was used for image pre-processing,template matching and positioning of the coil lead area to set up a coordinate system.After eliminating image noise by Blob analysis,the improved Canny algorithm was used to detect the location of the coil lead paint stripped region,and the time was reduced by about half compared to the Canny algorithm.The coil winding region was trained with the ShuffleNet V2-YOLOv5s model for the dataset,and the detect file was converted to the Open Neural Network Exchange(ONNX)model for the detection of winding cross features with an average accuracy of 99.0%.The software interface of the detection system was designed to perform qualified discrimination tests on the workpieces,and the detection data were recorded and statistically analyzed.The results showed that the stator winding coil qualified discrimination accuracy reached 96.2%,and the average detection time of a single workpiece was about 300 ms,while YOLOv5s took less than 30 ms.
文摘Based on the 6-pole outer stator(armature winding-stator),the influence of inner(permanent magnet-stator)/outer stator pole ratio n(n=NIS/NOS),stator relative positions and rotor pole number combinations on electromagnetic performance of partitioned stator switched flux permanent magnet(PM)machines(PS-SFPMMs)is investigated in this paper.Since the armature windings and PMs are located in two separated stators and PMs are stationary,PS-SFPMMs have high fault tolerance capabilities.To maximize the torque performance,the PM of inner stator pole should be aligned with outer stator pole when n is odd while the iron rib of inner stator pole should be aligned with outer stator pole when n is even.No matter what n is selected,the rotor pole number NR can be any integers except the phase number and its multiples.The analysis results indicate that the optimal NR is closed to(NIS+NOS)/2 and it is odd when n is odd while it is even when n is even.Meanwhile,symmetrical phase back-EMF waveform will be obtained when the ratio of Min(NOS,NIS)to the greatest common divisor of Min(NOS,NIS)and NR is even.Based on the optimal rotor pole numbers for 6-pole outer stator with different n and corresponding optimal relative position together with same rated copper loss,the average torque is improved by 18.4%,25.1%and 25.7%respectively in PS-SFPMMs with n equal to 2,3 and 4 when compared with PS-SFPMM with n equal to 1.The analyses are validated by experiment results of the prototype machine.
文摘This paper analyzes dynamic equivalent circuit of induction motor and the relationship among inner fluxes, then presents a direct stator flux oriented continuous torque control (DSFOCTC) scheme of induction motor , which uses stator current vector control instead of voltage vector control. As a combination of direct torque control (DTC) and flux oriented vector control, it achieves round stator flux and continuous dynamic torque control resulting in less torque ripple than that in DTC. It reduces the dependence on rotor parameters, and is especially insensitive to rotor resistance. Finally, an induction motor speed control system incorporating this novel scheme is given and checked by simulation.
基金National Natural Science FoundationDoctoral Programme Foundation of Institution of Higher Education of China
文摘The resonances of parametric vibration with forced vibration isanalyzed, the bifurca- tion equation of the system is obtained andthe singularity analysis is made. Some of the laws and phe- nomenaare revealed. The transition variety and bifurcation diagram of thephysical parameteric plane are given. the results can be used inengineering.
基金Supported by National Natural Science Foundation of China(Grant No.51575393)
文摘With application of the lock-up clutch in the torque converter(TC), fuel economy is not much determined by its high-speed ratio transmission efficiency. As a benefit, more researches are focused on its low-speed ratio performance so as to improve vehicle gradeability and launching acceleration performance. According to the results of computational fluid dynamics(CFD) analysis, hydrodynamic loss inside the stator cascade accounts for 42% of the total energy loss at stalling speed ratio. It is found that upstream flow with large impingement angle results in boundary layer separation at the leading edge, which aggregates hydrodynamic loss and decreases circular flow rate dramatically at low-speed ratio. In this paper, a dual-blade stator is proposed to suppress the boundary layer separation, which is parameterized by using the non-uniform rational B spline(NURBS) method. The mean camber line and blade profile curve are expressed by a three control points quadratic open NURBS and a cubic closed one respectively. The key design parameters included the slot width and suction side shape of the primary blade are analyzed. The most effective slot width is found to be between 4% and 8% chord length, and the boundary layer separation can be suppressed completely by decreasing distribution of momentum moment at the primary blade and adding it to the leading edge of the secondary blade. As a result, circular flow rate and impeller torque capacity is increased by 17.9% and 9.6% respectively at stalling speed ratio, meanwhile, low-speed ratio efficiency is also improved. Maximum efficiency at high-speed ratio decreases by 0.5%, which can be ignored as the work of lock-up clutch. This research focuses on using the dual-blade stator to optimize low-speed ratio performance of the TC, which is benefit to vehicle power performance.
基金Supported by the National Natural Science Foundation of China(21776180,21776181,21306116)Hou Hua Ku Project of Sichuan University(2018SCUH0012).
文摘Rotor–stator reactor(RSR), an efficient mass transfer enhancer, has been applied in many fields. However,the hydrodynamic characteristics of liquid flow in RSR are still a mystery despite they are fundamental for the mass transfer performance and processing capacity. In view of the above, this paper studies the liquid–liquid flow and liquid holdup in RSR under various conditions with a high-speed camera. The paper firstly demonstrates two flow patterns and liquid holdup patterns that we obtained from our experiment and then presents in succession a flow pattern and a liquid holdup criterion for the transition of film flow to filament flow and complete filling to incomplete filling. It is found that experimental parameters, including rotor–stator distance, rotational speed and volume flow rate exert great influence on the average droplet diameter and size distribution. Besides, by comparison and contrast, we also find that the experimental values match well with our previous predicted calculations of the average diameter, and the relation between the average diameter and the mean energy dissipation rate.
基金National Nature Science Foundation of China(No.61175125) 2010 Major Project of Yuhang City Technology Division of China
文摘The research object used in the dissertation was screw pump, which was widely applied in engineering field. The analysis of end face profile formation was completed on its main working components, i.e., rotor and stator. With the purpose of finding optimal parameters to improve the efficiency of screw pump design, the key technologies involved in the parametric modeling of rotor and stator were analyzed. The three-dimensional (3D) design software SolidWorks was used for the secondary development and parametric modeling of rotor and stator. After that the simulation models of different kinds of screw pumps were established based on the cycloid type, variation coefficient, and screw head number. Finally the COSMOSMotion was used to analyze the motion characteristics on the equidistant line of rotor, including velocity and acceleration. This design and modeling method has been used in screw pump enterprises for design and development, laying the foundation for finite element analysis and further optimization of screw pump.
文摘Presents the mathematic model built for double stator permanent magnet synchronous motors through a brief analysis of their future development, and the equations established for calculation of their torques, and the development of prototypes, and discusses the comparison of the motor under development with the conventional motors with the same volume, stator structure, and magnet shape, and concludes the motor under development is one of the ways to improve the performance/volume ratio of motors.
基金This work was supported in part by National Natural Science Foundation for Excellent Young Scholar of China under Award 51622704,in part by Jiangsu provincial key research and development project under Award BE2017160。
文摘With the development of aviation electrification,higher demands for electrical machines are put forward in aircraft electric propulsion systems.The aircraft electric propulsion requirements and propulsion motor features are analyzed in this paper.Comparing with conventional PM machines,ironless stator axial flux permanent magnet(AFPM)machine topologies with Litz wire windings allow designs with higher compactness,lightness and efficiency,which are suitable for high-frequency and high-power density applications.Based on the motor requirements and constraints of aircraft electric propulsion systems,this paper investigates a high-power 1 MW multi-stack ironless stator AFPM machine,which is composed of four 250kW modular motors by stacking in axial.The design guidelines and special attentions are presented,in term of electromagnetic,thermal,and mechanical performance for the high-frequency coils and Halbach-array PM rotor.Finally,an ironless stator AFPM motor is manufactured,tested and evaluated with the consideration of cost and processing cycle.The results show that the output power is up to 53.8kW with 95%efficiency at 9000r/min at this stage.The proposed ironless stator AFPM machine with oil immersed forced cooling proves to be a favorable candidate for application in electric aircraft as propulsion motors.
文摘The suppressing design of the engine nacelle in an aircraft can benefit from the development of the prediction system for the sound fields in engine ducts which includes the prediction of the source generation and that of sound propagation in ducts. First, the acoustic match mode principle between the source modes of rotor stator interaction noise and the propagation modes is presented in this paper. Second, by utilizing this principle, the theoretical prediction method for rotor stator interaction noise generation and its propagation and attenuation in an annular duct with multi treatments is developed. That means that the prediction of sound propagation and attenuation in the segmented ducts might no longer completely depend on the in duct mode measurements, and the investigation on the sound propagation and attenuation in ducts can be accomplished not only by acoustic mode measurement, but also by making use of the source prediction to determine the source modes excited by rotor stator interaction. The effects of fan speed, blade/vane numbers, axial spacing between rotor and stator on the in duct sound attenuation and generated sound power level before and after ducts (also including the sound power level of blade passing frequency and its harmonics at the inlet of ducts) have been numerically calculated by using this prediction method. The reliability of this prediction method is verified by reasonable agreement between the predicted results with measured results in references. By analyzing the results of calculating cases, some reference criteria are provided for the engineering design of the suppressing engine nacelle.
基金Sponsored by the National Natural Science Foundation of China(Grant No.51377041)
文摘The stator flux and electromagnetic torque observation is the basis of direct torque controlled permanent magnet synchronous motor( PMSM) drive system. However,the traditional stator flux observer based on voltage model is affected by integral initial values and integral drift,that based on current model is affected by the parameters of PMSM,so a new stator flux observation method is proposed based on an improved secondorder generalized integrator( SOGI). Compared to the stator flux observation method based on the conventional SOGI,the proposed method can not only overcome the influence of integral initial values and integral drift,but also completely eliminate the DC offset's influence. Therefore,the observation accuracy of stator flux is further improved. The simulation and experimental results both show that the proposed method has a higher stator flux and electromagnetic torque observation precision.
基金This project is supported by Provincial Science Foundation of Education Office of Hebei(No.Z2004455)Youth Research Fundation of State Power of China(No.SPQKJ02-10).
文摘Rotor vibration characteristics are first analyzed, which are that the rotor vibration of fundamental frequency will increase due to rotor winding inter-turn short circuit fault, air-gap dynamic eccentricity fault, or imbalance fault, and the vibration of the second frequency will increase when the air-gap static eccentricity fault occurs. Next, the characteristics of the stator winding parallel branches circulating current are analyzed, which are that the second harmonics circulating current will increase when the rotor winding inter-turn short circuit fault occurs, and the fundamental circulating current will increase when the air-gap eccentricity fault occurs, neither being strongly affected by the imbalance fault. Considering the differences of the rotor vibration and circulating current characteristics caused by different rotor faults, a method of generator vibration fault diagnosis, based on rotor vibration and circulating current characteristics, is developed. Finally, the rotor vibration and circulating current of a type SDF-9 generator is measured in the laboratory to verify the theoretical analysis presented above.
文摘A novel cooling system with cooling channels is proposed for the stator of 3MW wind-driven generator.An experimental platform is built to investigate the performance of the cooling system with different loads.At30%,50% or 80% generator loads,the temperatures meet the design requirement.However,it is a little over the requirement at 100%load,duo to experimental errors and some unknown thermal resistances.In the test at 100%load,the developing trends of the parameters of these two generators are similar and only minor differences occurs when they reach steady state our work can be benefit for the design and improvement of MW wind-driven generator cooling solutions.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51677051 and 51377039)the Fund from the Anhui Province Key Laboratory of Large-scale Submersible Electric Pump and Accoutrements
文摘In large-scale electric machines, unbalanced magnetic pull (UMP) caused by eccentricity usually results in stator-rotor rub, so it is necessary to investigate the amplitude and the influencing factors. This paper takes the squirrel-cage induction motor as an example. A magnetic loop model of an induction motor is established by an analytical method. The impact of stator winding setup (parallel branch and pole pairs) on each magnetomotive force (MMF) and unbalanced magnetic pull is analyzed. Using the finite element simulation method, the spatial and time distribution of flux density of the rotor outer circle under static eccentricity is obtained, and the unbalanced magnetic pull calculation caused by static eccentricity is completed. The conclusion of the influence of stator winding on the size of unbalanced magnetic pull provides reliable gist for motor noise and vibration analysis, and especially provides an important reference for large induction motor design.
文摘A new design of stato magnetic System is Proposed for 3-phase & 12-pole HB stepper, and it features bet-ter distribution of magntic lield to incare Pullou tope and bopmve Operaonal stability of moor and minimummutual inductance between phase windimp to make design of control circuit easier, and application proved it is as good as expected.
基金This research was supported by the Key Technology R&D Programof State Power Corporation of China During the Tenth-Five-Year Plan Period.
文摘The breakdown voltage plays an important role in evaluating residual life of stator insulation in generator.In this paper,we discussed BP neural network that was used to predict the breakdown voltage of stator insulation in generator of 300MW/18kV.At first the neural network has been trained by the samples that include the varieties of dielectric loss factor tanδ,the partial discharge parameters and breakdown voltage.Then we tried to predict the breakdown voltage of samples and stator insulations subjected to multi-stress aging by the trained neural network.We found that it's feasible and accurate to predict the voltage.This method can be applied to predict breakdown voltage of other generators which have the same insulation structure and material.
文摘A double-shell model of hydroelectric-generator stator system was established. Applying the theory of mechano-electric analytical dynamics theory, the nonlinear vibration equation of magnetism and solid coupling of hydroelectric-generator stator system, under steadily balanced three-phases operating condition, was obtained. According to the method of multiple scales for nonlinear oscillations, the double resonances of magnetism and solid coupling of hydroelectric-generator stater system, were investigated. It is pointed out that the system has abundant dynamics phenomenon including the attendant jumps and coexistence of multiple stable motions.
基金National Natural Science Foundation of China(No.61105114)the Key Technology R&D Program of Jiangsu Province,China(No.BE2010189)
文摘Quick detection of a small initial fault is important for an induction motor to prevent a consequent large fault.The mathematical model with basic motor equations among voltages,currents,and fluxes is analyzed and the motor model equations are described.The fault related features are extracted.An immune memory dynamic clonal strategy(IMDCS)system is applied to detecting the stator faults of induction motor.Four features are obtained from the induction motor,and then these features are given to the IMDCS system.After the motor condition has been learned by the IMDCS system,the memory set obtained in the training stage can be used to detect any fault.The proposed method is experimentally implemented on the induction motor,and the experimental results show the applicability and effectiveness of the proposed method to the diagnosis of stator winding turn faults in induction motors.
文摘One of the solutions to reduce fuel consumption of diesel generators (DG) is to adapt the rotational speed to mechanical torque of the crankshaft. When load power decreases, a reduction in both mechanical torque and rotational speed of the diesel engine will maintain the combustion efficiency near the levels of the nominal regime. Accordingly, the generator itself should operate at a variable speed which normally requires power electronics converters. In this paper, we are exploring a new generator concept that uses a stator rotating in opposite direction to the rotor such as the relative velocity between the two components remains constant when diesel engine slows down. The stator itself is driven by a compensator synchronous motor (CM) such as the relative velocity of the rotor is constant, eliminating as such sophisticated power electronics. The model developed for the synchronous machine with a rotating stator is based on Park’s transformation. This new concept was modelled using MATLAB software. Experimental analysis has been conducted using a 500-kW diesel GENSET equipped with a permanent magnet synchronous generator (PMSG). The numerical and experimental results are in good agreement and demonstrate that fuel consumption is reduced with a rotating-mode stator for PMSG during low electrical loads.