A tracking stability control problem for the vertical electric stabilization system of moving tank based on adaptive robust servo control is addressed.This paper mainly focuses on two types of possibly fast timevaryin...A tracking stability control problem for the vertical electric stabilization system of moving tank based on adaptive robust servo control is addressed.This paper mainly focuses on two types of possibly fast timevarying but bounded uncertainty within the vertical electric stabilization system:model parameter uncertainty and uncertain nonlinearity.First,the vertical electric stabilization system is constructed as an uncertain nonlinear dynamic system that can reflect the practical mechanics transfer process of the system.Second,the dynamical equation in the form of state space is established by designing the angular tracking error.Third,the comprehensive parameter of system uncertainty is designed to estimate the most conservative effects of uncertainty.Finally,an adaptive robust servo control which can effectively handle the combined effects of complex nonlinearity and uncertainty is proposed.The feasibility of the proposed control strategy under the practical physical condition is validated through the tests on the experimental platform.This paper pioneers the introduction of the internal nonlinearity and uncertainty of the vertical electric stabilization system into the settlement of the tracking stability control problem,and validates the advanced servo control strategy through experiment for the first time.展开更多
A proportional integral derivative (PID) controller is designed and attached to electro-hydraulic servo actuator system (EHSAS) to control the angular position of the rotary actuator which control the movable surf...A proportional integral derivative (PID) controller is designed and attached to electro-hydraulic servo actuator system (EHSAS) to control the angular position of the rotary actuator which control the movable surface of space vehicles. The PID gain parameters are optimized by the genetic algorithm (GA). The controller is verified on the new state-space model of servo-valves attached to the physical rotary actuator by SIMULINK program. The controller and the state-space model are verified experimentally. Simulation and experimental results verify the effectiveness of the PID controller adaptive by GA to control the angular position of the rotary actuator as compared with the classical PID controller and the compensator controller.展开更多
Voice coil motor(VCM) is a special direct drive linear motor, which can convert electric energy directly into mechanical energy without the use of transmission mechanism. VCM has the advantages of simple structure, go...Voice coil motor(VCM) is a special direct drive linear motor, which can convert electric energy directly into mechanical energy without the use of transmission mechanism. VCM has the advantages of simple structure, good rigidity, fast response, silence, high linearity, no cogging force, no pulsation et al. It is widely used in the field of high-precision control. This paper reviews and summarizes the results of VCM research conducted by scholars from various countries, and summarizes the general situation of VCM servo control technology. Firstly, a basic description of VCM’s mathematical model and common control mechanisms is provided. The benefits, drawbacks, and application of control techniques in the field of VCM are all explored in detail;At the same time, the methods to improve control strategy are proposed;Then, combined with the analysis and research of scholars in various countries on VCM, the problems of difficult to establish accurate model, friction disturbance and mechanical vibration of VCM and the solutions to the corresponding problems are summarized;Finally, a summary of VCM’s application fields is provided.展开更多
The angular position controller is system (EHSAS) to control the output of the rotary applied to electro-hydraulic servo actuator actuator. It works as a compensator based on the frequency response of the EHSAS. Its...The angular position controller is system (EHSAS) to control the output of the rotary applied to electro-hydraulic servo actuator actuator. It works as a compensator based on the frequency response of the EHSAS. Its design model is verified on the state-space model of EHSAS by using simulation program SIMULINK. Real data used to test the system. Simulation results give a good agreement for the controller and also for the state-space model.展开更多
The reliability and robustness of the electro-hydraulic servo control system for heavy-duty forging machine play an important role in forging processes. A mathematic model of 50 MN water press for free forging was cre...The reliability and robustness of the electro-hydraulic servo control system for heavy-duty forging machine play an important role in forging processes. A mathematic model of 50 MN water press for free forging was created in this research. The dynamic robust compensator integrating with PID control method is designed and applied to the mathematical model simulation. The simulated results approved that the dynamic robust compensator application restrains interference from extra load and improves the electro-hydraulic position servo control system accuracy and stability.展开更多
An ultra-precision servo control system for MWEDM (micro wire electrical discharge machining) based on piezoelectric ceramic motor drivers was developed. The servo discharge detection adopts an average voltage detecti...An ultra-precision servo control system for MWEDM (micro wire electrical discharge machining) based on piezoelectric ceramic motor drivers was developed. The servo discharge detection adopts an average voltage detection method, utilizes statistical methods to analyze the measured data, then controls discharge gap and makes the process more stable. The servo feed system based on DSP microprocessors applies a PID controller with incomplete derivation to reduce overshoot to improve machining accuracy, and also adopts adaptive dead-zone inverse compensation to eliminate dead-zone caused by piezoelectric ceramic motions in low servo feed speed. The simulation results show that the methods proposed in this paper can make the system recover its linearity and converge the dead-zone parameters. It is proved that the method proposed is efficient in solving this problem. Cooperating with a micro energy pulse generator, this equipment’s machining accuracy is smaller than ±0.2 micron, and surface roughness Ra is less than 0.1 micron. Punch die and cavity die (micro gear die, module 100 micron, thickness 3.5 millimeter) have been machined independently in two die steel work-pieces. These pieces can mate very well to work, which shows that the servo control system satisfies the need of MWEDM for high precision micro fabrication.展开更多
A new visual servo control scheme for a robotic manipulator is presented in this paper, where a back propagation (BP) neural network is used to make a direct transition from image feature to joint angles without req...A new visual servo control scheme for a robotic manipulator is presented in this paper, where a back propagation (BP) neural network is used to make a direct transition from image feature to joint angles without requiring robot kinematics and camera calibration. To speed up the convergence and avoid local minimum of the neural network, this paper uses a genetic algorithm to find the optimal initial weights and thresholds and then uses the BP Mgorithm to train the neural network according to the data given. The proposed method can effectively combine the good global searching ability of genetic algorithms with the accurate local searching feature of BP neural network. The Simulink model for PUMA560 robot visual servo system based on the improved BP neural network is built with the Robotics Toolbox of Matlab. The simulation results indicate that the proposed method can accelerate convergence of the image errors and provide a simple and effective way of robot control.展开更多
A novel electro-hydraulic servo control algorithm was introduced. The primary idea of this algorithm was to combine the notion of model prediction with the generic model control (GMC). The performance of the GMC al-...A novel electro-hydraulic servo control algorithm was introduced. The primary idea of this algorithm was to combine the notion of model prediction with the generic model control (GMC). The performance of the GMC al- gorithm was improved by receding optimization and feedback correction. By the predictive model of output errors of an electro-hydraulic servo control system based on the improved weighted least square support vector machines (WLS-SVM) to forecast and compensate the future sequence errors, the control precision and robustness were im- proved. The improved GMC based on the improved WLS-SVM was applied to an electro-hydraulic servo control sys- tem for hot strip rolling control systems. The simulation results showed the feasibility and effectiveness of the pres- ent algorithm.展开更多
The recoil distance Doppler shift method has been widely used in the study of nuclear structure to determine the level lifetime and absolute transition probabilities.A capacitance servo control plunger based on this m...The recoil distance Doppler shift method has been widely used in the study of nuclear structure to determine the level lifetime and absolute transition probabilities.A capacitance servo control plunger based on this method has been successfully developed by the Nuclear Structure Group of the China Institute of Atomic Energy.Three microscopes were employed to check the parallelism and can therefore guarantee a delicate measurement of the distance between the target and the stopper.This new plunger made a successful performance in the test experiment and the measured lifetime of the 2~+→0~+ transition in ^(78)Kr is in agreement with the previous value.展开更多
The tele-operation robotic system which consists of an excavator as the construction robot, and two joysticks for operating the robot from a safe place are useful for performing restoration in damaged areas. In order ...The tele-operation robotic system which consists of an excavator as the construction robot, and two joysticks for operating the robot from a safe place are useful for performing restoration in damaged areas. In order to accomplish a precise task, the operator needs to feel a realistic sense of task force brought about from a feedback force between the fork glove of slave robot and unfamiliar environment. A novel force feedback model is proposed based on velocity control of cylinder to determine environment force acting on fork glove. Namely, the feedback force is formed by the error of displacement of joystick with velocity and driving force of piston, and the gain is calculated by the driving force and threshold of driving force of hydraulic cylinder. Moreover, the variable gain improved algorithm is developed to overcome the defect for grasping soft object. Experimental results for fork glove freedom of robotic system are provided to demonstrate the developed algorithm is available for grasping soft object.展开更多
A new kind of volume control hydraulic press that combines the advantages of both hydraulic and SRM(switched reluctance motor) driving technology is developed.Considering that the serious dead zone and time-variant no...A new kind of volume control hydraulic press that combines the advantages of both hydraulic and SRM(switched reluctance motor) driving technology is developed.Considering that the serious dead zone and time-variant nonlinearity exist in the volume control electro-hydraulic servo system,the ILC(iterative learning control) method is applied to tracking the displacement curve of the hydraulic press slider.In order to improve the convergence speed and precision of ILC,a fuzzy ILC algorithm that utilizes the fuzzy strategy to adaptively adjust the iterative learning gains is put forward.The simulation and experimental researches are carried out to investigate the convergence speed and precision of the fuzzy ILC for hydraulic press slider position tracking.The results show that the fuzzy ILC can raise the iterative learning speed enormously,and realize the tracking control of slider displacement curve with rapid response speed and high control precision.In experiment,the maximum tracking error 0.02 V is achieved through 12 iterations only.展开更多
The dynamics of hydraulic systems are highly nonlinear and the system may be subjected to non-smooth and discontinuous nonlinearities due to directional change of valve opening, friction, etc. Aside from the nonlinear...The dynamics of hydraulic systems are highly nonlinear and the system may be subjected to non-smooth and discontinuous nonlinearities due to directional change of valve opening, friction, etc. Aside from the nonlinear nature of hydraulic dynamics, hydraulic servo systems also have large extent of model uncertainties. To address these challenging issues, a robust state-feedback controller is designed by employing backstepping design technique such that the system output tracks a given signal arbitrarily well, and all signals in the closed-loop system remain bounded. Moreover, a relevant disturbance attenuation inequality is satisfied by the closed-loop signals. Compared with previously proposed robust controllers, this paper's robust controller based on backstepping recursive design method is easier to design, and is more suitable for implementation.展开更多
A learning-based control approach is presented for force servoing of a robot with vision in an unknown environment. Firstly, mapping relationships between image features of the servoing object and the joint angles of ...A learning-based control approach is presented for force servoing of a robot with vision in an unknown environment. Firstly, mapping relationships between image features of the servoing object and the joint angles of the robot are derived and learned by a neural network. Secondly, a learning controller based on the neural network is designed for the robot to trace the object. Thirdly, a discrete time impedance control law is obtained for the force servoing of the robot, the on-line learning algorithms for three neural networks are developed to adjust the impedance parameters of the robot in the unknown environment. Lastly, wiping experiments are carried out by using a 6 DOF industrial robot with a CCD camera and a force/torque sensor in its end effector, and the experimental results confirm the effecti veness of the approach.展开更多
The pneumatic rotary position system, in which an electro-pneumatic proportional flow valve controled a rotary cylinder, was studied, and its mathematical model was built. The model indicated that the controlled pneum...The pneumatic rotary position system, in which an electro-pneumatic proportional flow valve controled a rotary cylinder, was studied, and its mathematical model was built. The model indicated that the controlled pneumatic system had disadvantages such as inherent non-linearity and variations of system parameters with working points. In order to improve the dynamic performance of the system, feed forward compensation self-tuning pole-placement strategy was adopted to place the poles of the system in a desired position in real time, and a recursive least square method with fixed forgetting factors was also used in the parameter estimation. Experimental results show that the steady state error of the pneumatic rotary position system is within 3% and the identified system parameters can be converged in 5 s. Under different loads, the controlled system has an excellent tracking performance and robustness of anti-disturbance.展开更多
A visual servoing tracking controller is proposed based on the sliding mode control theory in order to achieve strong robustness against parameter variations and external disturbances. A sliding plane with time delay ...A visual servoing tracking controller is proposed based on the sliding mode control theory in order to achieve strong robustness against parameter variations and external disturbances. A sliding plane with time delay compensation is presented by the pre-estimate of states. To reduce the chattering of the sliding mode controller, a modified exponential reaching law and hyperbolic tangent function are applied to the design of visual controller and robot joint controller. Simulation results show that the visual servoing control scheme is robust and has good tracking performance.展开更多
In IBVS (image based visual servoing), the error signal in image space should be transformed into the control signal in the input space quickly. To avoid the iterative adjustment and complicated inverse solution of im...In IBVS (image based visual servoing), the error signal in image space should be transformed into the control signal in the input space quickly. To avoid the iterative adjustment and complicated inverse solution of image Jacobian, CMAC (cerebellar model articulation controller) neural network is inserted into visual servo control loop to implement the nonlinear mapping. Two control schemes are used. Simulation results on two schemes are provided, which show a better tracking precision and stability can be achieved using scheme 2.展开更多
Flight simulator is an important device and a typical high-performance position and speed servo system used in the hardware-in-the-loop simulation of flight control system. Friction is the main nonlinear resistance in...Flight simulator is an important device and a typical high-performance position and speed servo system used in the hardware-in-the-loop simulation of flight control system. Friction is the main nonlinear resistance in the flight simulator servo system, especially in a low-speed state. Based on the description of dynamic and static models of a nonlinear Stribeck friction model, this paper puts forward sliding mode controller to overcome the friction, whose stability is展开更多
Although conventional model reference adaptive control (MRAC) achieves good tracking performance for cylinder control, the controller structure is much more complicated and has less robustness to disturbance in real...Although conventional model reference adaptive control (MRAC) achieves good tracking performance for cylinder control, the controller structure is much more complicated and has less robustness to disturbance in real applications. This paper discusses the use of simple adaptive control (SAC) for positioning a water hydraulic servo cylinder system. Compared with MRAC, SAC has a simpler and lower order structure, i.e., higher feasibility. The control performance of SAC is examined and evaluated on a water hydraulic servo cylinder system. With the recent increased concerns over global environmental problems, the water hydraulic technique using pure tap water as a pressure medium has become a new drive source comparable to electric, oil hydraulic, and pneumatic drive systems. This technique is also preferred because of its high power density, high safety against fire hazards in production plants, and easy availability. However, the main problems for precise control in a water hydraulic system are steady state errors and overshoot due to its large friction torque and considerable leakage flow. MRAC has been already applied to compensate for these effects, and better control performances have been obtained. However, there have been no reports on the application of SAC for water hydraulics. To make clear the merits of SAC, the tracking control performance and robustness are discussed based on experimental results. SAC is confirmed to give better tracking performance compared with PI control, and a control precision comparable to MRAC (within 10 μm of the reference position) and higher robustness to parameter change, despite the simple controller. The research results ensure a wider application of simple adaptive control in real mechanical systems.展开更多
An AC servo system based on neuron control theory is presented. Experimental results show that the neuralcontrol mode doesn't need the Precise model of the system, therefore, it has many advantages, such as simple...An AC servo system based on neuron control theory is presented. Experimental results show that the neuralcontrol mode doesn't need the Precise model of the system, therefore, it has many advantages, such as simple designand high response performance. The simulation research of the AC servo system which is non-linear, time-varied.based on neuro-fuzzy controller is done. The results of the simulation show that the performances of the system areconsiderably improved and it is one of the novel pathways to realize intelligent control of servo system.展开更多
基金supported in part by the Nation Natural Science Foundation of China under Grant No.52175099China Postdoctoral Science Foundation under Grant No.2020M671494Jiangsu Planned Projects for Postdoctoral Research Funds under Grant No.2020Z179。
文摘A tracking stability control problem for the vertical electric stabilization system of moving tank based on adaptive robust servo control is addressed.This paper mainly focuses on two types of possibly fast timevarying but bounded uncertainty within the vertical electric stabilization system:model parameter uncertainty and uncertain nonlinearity.First,the vertical electric stabilization system is constructed as an uncertain nonlinear dynamic system that can reflect the practical mechanics transfer process of the system.Second,the dynamical equation in the form of state space is established by designing the angular tracking error.Third,the comprehensive parameter of system uncertainty is designed to estimate the most conservative effects of uncertainty.Finally,an adaptive robust servo control which can effectively handle the combined effects of complex nonlinearity and uncertainty is proposed.The feasibility of the proposed control strategy under the practical physical condition is validated through the tests on the experimental platform.This paper pioneers the introduction of the internal nonlinearity and uncertainty of the vertical electric stabilization system into the settlement of the tracking stability control problem,and validates the advanced servo control strategy through experiment for the first time.
文摘A proportional integral derivative (PID) controller is designed and attached to electro-hydraulic servo actuator system (EHSAS) to control the angular position of the rotary actuator which control the movable surface of space vehicles. The PID gain parameters are optimized by the genetic algorithm (GA). The controller is verified on the new state-space model of servo-valves attached to the physical rotary actuator by SIMULINK program. The controller and the state-space model are verified experimentally. Simulation and experimental results verify the effectiveness of the PID controller adaptive by GA to control the angular position of the rotary actuator as compared with the classical PID controller and the compensator controller.
文摘Voice coil motor(VCM) is a special direct drive linear motor, which can convert electric energy directly into mechanical energy without the use of transmission mechanism. VCM has the advantages of simple structure, good rigidity, fast response, silence, high linearity, no cogging force, no pulsation et al. It is widely used in the field of high-precision control. This paper reviews and summarizes the results of VCM research conducted by scholars from various countries, and summarizes the general situation of VCM servo control technology. Firstly, a basic description of VCM’s mathematical model and common control mechanisms is provided. The benefits, drawbacks, and application of control techniques in the field of VCM are all explored in detail;At the same time, the methods to improve control strategy are proposed;Then, combined with the analysis and research of scholars in various countries on VCM, the problems of difficult to establish accurate model, friction disturbance and mechanical vibration of VCM and the solutions to the corresponding problems are summarized;Finally, a summary of VCM’s application fields is provided.
文摘The angular position controller is system (EHSAS) to control the output of the rotary applied to electro-hydraulic servo actuator actuator. It works as a compensator based on the frequency response of the EHSAS. Its design model is verified on the state-space model of EHSAS by using simulation program SIMULINK. Real data used to test the system. Simulation results give a good agreement for the controller and also for the state-space model.
文摘The reliability and robustness of the electro-hydraulic servo control system for heavy-duty forging machine play an important role in forging processes. A mathematic model of 50 MN water press for free forging was created in this research. The dynamic robust compensator integrating with PID control method is designed and applied to the mathematical model simulation. The simulated results approved that the dynamic robust compensator application restrains interference from extra load and improves the electro-hydraulic position servo control system accuracy and stability.
文摘An ultra-precision servo control system for MWEDM (micro wire electrical discharge machining) based on piezoelectric ceramic motor drivers was developed. The servo discharge detection adopts an average voltage detection method, utilizes statistical methods to analyze the measured data, then controls discharge gap and makes the process more stable. The servo feed system based on DSP microprocessors applies a PID controller with incomplete derivation to reduce overshoot to improve machining accuracy, and also adopts adaptive dead-zone inverse compensation to eliminate dead-zone caused by piezoelectric ceramic motions in low servo feed speed. The simulation results show that the methods proposed in this paper can make the system recover its linearity and converge the dead-zone parameters. It is proved that the method proposed is efficient in solving this problem. Cooperating with a micro energy pulse generator, this equipment’s machining accuracy is smaller than ±0.2 micron, and surface roughness Ra is less than 0.1 micron. Punch die and cavity die (micro gear die, module 100 micron, thickness 3.5 millimeter) have been machined independently in two die steel work-pieces. These pieces can mate very well to work, which shows that the servo control system satisfies the need of MWEDM for high precision micro fabrication.
文摘A new visual servo control scheme for a robotic manipulator is presented in this paper, where a back propagation (BP) neural network is used to make a direct transition from image feature to joint angles without requiring robot kinematics and camera calibration. To speed up the convergence and avoid local minimum of the neural network, this paper uses a genetic algorithm to find the optimal initial weights and thresholds and then uses the BP Mgorithm to train the neural network according to the data given. The proposed method can effectively combine the good global searching ability of genetic algorithms with the accurate local searching feature of BP neural network. The Simulink model for PUMA560 robot visual servo system based on the improved BP neural network is built with the Robotics Toolbox of Matlab. The simulation results indicate that the proposed method can accelerate convergence of the image errors and provide a simple and effective way of robot control.
基金Item Sponsored by National Development and Reform Commission Tech-Industry Project Foundation of China(High-Tech1899)
文摘A novel electro-hydraulic servo control algorithm was introduced. The primary idea of this algorithm was to combine the notion of model prediction with the generic model control (GMC). The performance of the GMC al- gorithm was improved by receding optimization and feedback correction. By the predictive model of output errors of an electro-hydraulic servo control system based on the improved weighted least square support vector machines (WLS-SVM) to forecast and compensate the future sequence errors, the control precision and robustness were im- proved. The improved GMC based on the improved WLS-SVM was applied to an electro-hydraulic servo control sys- tem for hot strip rolling control systems. The simulation results showed the feasibility and effectiveness of the pres- ent algorithm.
基金Supported by National Natural Science Foundation of China(10675171,10927507,11075214,11175259)
文摘The recoil distance Doppler shift method has been widely used in the study of nuclear structure to determine the level lifetime and absolute transition probabilities.A capacitance servo control plunger based on this method has been successfully developed by the Nuclear Structure Group of the China Institute of Atomic Energy.Three microscopes were employed to check the parallelism and can therefore guarantee a delicate measurement of the distance between the target and the stopper.This new plunger made a successful performance in the test experiment and the measured lifetime of the 2~+→0~+ transition in ^(78)Kr is in agreement with the previous value.
基金supported by National Natural Science Foundation of China(No.50475011).
文摘The tele-operation robotic system which consists of an excavator as the construction robot, and two joysticks for operating the robot from a safe place are useful for performing restoration in damaged areas. In order to accomplish a precise task, the operator needs to feel a realistic sense of task force brought about from a feedback force between the fork glove of slave robot and unfamiliar environment. A novel force feedback model is proposed based on velocity control of cylinder to determine environment force acting on fork glove. Namely, the feedback force is formed by the error of displacement of joystick with velocity and driving force of piston, and the gain is calculated by the driving force and threshold of driving force of hydraulic cylinder. Moreover, the variable gain improved algorithm is developed to overcome the defect for grasping soft object. Experimental results for fork glove freedom of robotic system are provided to demonstrate the developed algorithm is available for grasping soft object.
基金Project(2007AA04Z144) supported by the National High-Tech Research and Development Program of ChinaProject(2007421119) supported by the China Postdoctoral Science Foundation
文摘A new kind of volume control hydraulic press that combines the advantages of both hydraulic and SRM(switched reluctance motor) driving technology is developed.Considering that the serious dead zone and time-variant nonlinearity exist in the volume control electro-hydraulic servo system,the ILC(iterative learning control) method is applied to tracking the displacement curve of the hydraulic press slider.In order to improve the convergence speed and precision of ILC,a fuzzy ILC algorithm that utilizes the fuzzy strategy to adaptively adjust the iterative learning gains is put forward.The simulation and experimental researches are carried out to investigate the convergence speed and precision of the fuzzy ILC for hydraulic press slider position tracking.The results show that the fuzzy ILC can raise the iterative learning speed enormously,and realize the tracking control of slider displacement curve with rapid response speed and high control precision.In experiment,the maximum tracking error 0.02 V is achieved through 12 iterations only.
文摘The dynamics of hydraulic systems are highly nonlinear and the system may be subjected to non-smooth and discontinuous nonlinearities due to directional change of valve opening, friction, etc. Aside from the nonlinear nature of hydraulic dynamics, hydraulic servo systems also have large extent of model uncertainties. To address these challenging issues, a robust state-feedback controller is designed by employing backstepping design technique such that the system output tracks a given signal arbitrarily well, and all signals in the closed-loop system remain bounded. Moreover, a relevant disturbance attenuation inequality is satisfied by the closed-loop signals. Compared with previously proposed robust controllers, this paper's robust controller based on backstepping recursive design method is easier to design, and is more suitable for implementation.
基金This project was supported by the research foundation of China Education Ministry for the scholars from abroad (2002247).
文摘A learning-based control approach is presented for force servoing of a robot with vision in an unknown environment. Firstly, mapping relationships between image features of the servoing object and the joint angles of the robot are derived and learned by a neural network. Secondly, a learning controller based on the neural network is designed for the robot to trace the object. Thirdly, a discrete time impedance control law is obtained for the force servoing of the robot, the on-line learning algorithms for three neural networks are developed to adjust the impedance parameters of the robot in the unknown environment. Lastly, wiping experiments are carried out by using a 6 DOF industrial robot with a CCD camera and a force/torque sensor in its end effector, and the experimental results confirm the effecti veness of the approach.
基金Project(50375034) supported by the National Natural Science Foundation of China
文摘The pneumatic rotary position system, in which an electro-pneumatic proportional flow valve controled a rotary cylinder, was studied, and its mathematical model was built. The model indicated that the controlled pneumatic system had disadvantages such as inherent non-linearity and variations of system parameters with working points. In order to improve the dynamic performance of the system, feed forward compensation self-tuning pole-placement strategy was adopted to place the poles of the system in a desired position in real time, and a recursive least square method with fixed forgetting factors was also used in the parameter estimation. Experimental results show that the steady state error of the pneumatic rotary position system is within 3% and the identified system parameters can be converged in 5 s. Under different loads, the controlled system has an excellent tracking performance and robustness of anti-disturbance.
基金supported by China Postdoctoral Science Founda-tion (No. 20080441093)Key Laboratory Foundation of Liaoning Province (No. 2008S088).
文摘A visual servoing tracking controller is proposed based on the sliding mode control theory in order to achieve strong robustness against parameter variations and external disturbances. A sliding plane with time delay compensation is presented by the pre-estimate of states. To reduce the chattering of the sliding mode controller, a modified exponential reaching law and hyperbolic tangent function are applied to the design of visual controller and robot joint controller. Simulation results show that the visual servoing control scheme is robust and has good tracking performance.
基金This project is supported by National Natural Science Foundation of China (No.59990470).
文摘In IBVS (image based visual servoing), the error signal in image space should be transformed into the control signal in the input space quickly. To avoid the iterative adjustment and complicated inverse solution of image Jacobian, CMAC (cerebellar model articulation controller) neural network is inserted into visual servo control loop to implement the nonlinear mapping. Two control schemes are used. Simulation results on two schemes are provided, which show a better tracking precision and stability can be achieved using scheme 2.
基金This project was supported by the Aeronautics Foundation of China (00E21022).
文摘Flight simulator is an important device and a typical high-performance position and speed servo system used in the hardware-in-the-loop simulation of flight control system. Friction is the main nonlinear resistance in the flight simulator servo system, especially in a low-speed state. Based on the description of dynamic and static models of a nonlinear Stribeck friction model, this paper puts forward sliding mode controller to overcome the friction, whose stability is
文摘Although conventional model reference adaptive control (MRAC) achieves good tracking performance for cylinder control, the controller structure is much more complicated and has less robustness to disturbance in real applications. This paper discusses the use of simple adaptive control (SAC) for positioning a water hydraulic servo cylinder system. Compared with MRAC, SAC has a simpler and lower order structure, i.e., higher feasibility. The control performance of SAC is examined and evaluated on a water hydraulic servo cylinder system. With the recent increased concerns over global environmental problems, the water hydraulic technique using pure tap water as a pressure medium has become a new drive source comparable to electric, oil hydraulic, and pneumatic drive systems. This technique is also preferred because of its high power density, high safety against fire hazards in production plants, and easy availability. However, the main problems for precise control in a water hydraulic system are steady state errors and overshoot due to its large friction torque and considerable leakage flow. MRAC has been already applied to compensate for these effects, and better control performances have been obtained. However, there have been no reports on the application of SAC for water hydraulics. To make clear the merits of SAC, the tracking control performance and robustness are discussed based on experimental results. SAC is confirmed to give better tracking performance compared with PI control, and a control precision comparable to MRAC (within 10 μm of the reference position) and higher robustness to parameter change, despite the simple controller. The research results ensure a wider application of simple adaptive control in real mechanical systems.
文摘An AC servo system based on neuron control theory is presented. Experimental results show that the neuralcontrol mode doesn't need the Precise model of the system, therefore, it has many advantages, such as simple designand high response performance. The simulation research of the AC servo system which is non-linear, time-varied.based on neuro-fuzzy controller is done. The results of the simulation show that the performances of the system areconsiderably improved and it is one of the novel pathways to realize intelligent control of servo system.