In case of manufacturing hexahedral ABS (Acrylonitrile Butadiene Styrene) plastic components using a FDM (Fused Deposition Modeling)-based 3D printer, undesirable shape errors occur in the product due to heat shrinkag...In case of manufacturing hexahedral ABS (Acrylonitrile Butadiene Styrene) plastic components using a FDM (Fused Deposition Modeling)-based 3D printer, undesirable shape errors occur in the product due to heat shrinkage. This paper experimentally ob-served the influence of the bed temperature change on the deformed shape errors of a hexahedral specimen of 100 × 50 × 50 mm3 produced by using a 3D printer. During printing work, the head nozzle temperature was kept at 240?C and the head speed was set at 50 mm/s. The chamber was enclosed with a PC-plate. 3D printing was conducted at four different bed temperatures;50?C, 70?C, 90?C, and 110?C. After the produced specimens naturally cooled down to room temperature, their deformed shape errors were measured. As a result, the higher the bed temperature, the lower the deformed shape errors of the specimens were. However, if the bed temperature had exceeded 120?C, laminating adhesion became poor. That seems to occur because of the material phase change and can make 3D printing work very hard as a consequence. Results of this study can be helpful to set optimum bed temperature condition in FDM additive manufacturing.展开更多
The successive approximation register(SAR)is one of the most energy-efficient analog-to-digital converter(ADC)architecture for medium-resolution applications.However,its high energy efficiency quickly diminishes when ...The successive approximation register(SAR)is one of the most energy-efficient analog-to-digital converter(ADC)architecture for medium-resolution applications.However,its high energy efficiency quickly diminishes when the target resolution increases.This is because a SAR ADC suffers from several major error source,including the sampling kT/C noise,the comparator noise,and the DAC mismatch.These errors are increasing hard to address in high-resolution SAR ADCs.This paper reviews recent advances on error suppression techniques for SAR ADCs,including the sampling kT/C noise reduction,the noise-shaping(NS)SAR,and the mismatch error shaping(MES).These techniques aim to boost the resolution of SAR ADCs while maintaining their superior energy efficiency.展开更多
A novel approach for engineering application to human error probability quantification is presented based on an overview of the existing human reliability analysis methods.The set of performance shaping factors is cla...A novel approach for engineering application to human error probability quantification is presented based on an overview of the existing human reliability analysis methods.The set of performance shaping factors is classified as two subsets of dominant factors and adjusting factors respectively.Firstly,the dominant factors are used to determine the probabilities of three behavior modes.The basic probability and its interval of human error for each behavior mode are given.Secondly,the basic probability and its interval are modified by the adjusting factors,and the total probability of human error is calculated by a total probability formula.Finally,a simple example is introduced,and the consistency and validity of the presented approach are illustrated.展开更多
Shape from shading(SFS)is an important domain in computer vision.The paper presented an improved algorithm of shape from shading based on a single image according to an existed one.The presented algorithm enhanced the...Shape from shading(SFS)is an important domain in computer vision.The paper presented an improved algorithm of shape from shading based on a single image according to an existed one.The presented algorithm enhanced the boundary constraints to eliminate the rotation distortion on the border of reconstructed object and introduced the factor of brightness error to weaken the influence irradiance equation’s nonlinearity on reconstructed errors.The reconstructed results verify the performance improvement in terms of accuracy by the input image of a synthetic image and a real image of weld.展开更多
This paper aims at analyzing the shapes of the bounded traveling wave solutions for a class of nonlinear wave equation with a quintic term and obtaining its damped oscillatory solutions. The theory and method of plana...This paper aims at analyzing the shapes of the bounded traveling wave solutions for a class of nonlinear wave equation with a quintic term and obtaining its damped oscillatory solutions. The theory and method of planar dynamical systems are used to make a qualitative analysis to the planar dynamical system which the bounded traveling wave solutions of this equation correspond to. The shapes, existent number, and conditions are presented for all bounded traveling wave solutions. The bounded traveling wave solutions are obtained by the undetermined coefcients method according to their shapes, including exact expressions of bell and kink profile solitary wave solutions and approximate expressions of damped oscillatory solutions. For the approximate damped oscillatory solution, using the homogenization principle, its error estimate is given by establishing the integral equation, which reflects the relation between the exact and approximate solutions. It can be seen that the error is infinitesimal decreasing in the exponential form.展开更多
文摘In case of manufacturing hexahedral ABS (Acrylonitrile Butadiene Styrene) plastic components using a FDM (Fused Deposition Modeling)-based 3D printer, undesirable shape errors occur in the product due to heat shrinkage. This paper experimentally ob-served the influence of the bed temperature change on the deformed shape errors of a hexahedral specimen of 100 × 50 × 50 mm3 produced by using a 3D printer. During printing work, the head nozzle temperature was kept at 240?C and the head speed was set at 50 mm/s. The chamber was enclosed with a PC-plate. 3D printing was conducted at four different bed temperatures;50?C, 70?C, 90?C, and 110?C. After the produced specimens naturally cooled down to room temperature, their deformed shape errors were measured. As a result, the higher the bed temperature, the lower the deformed shape errors of the specimens were. However, if the bed temperature had exceeded 120?C, laminating adhesion became poor. That seems to occur because of the material phase change and can make 3D printing work very hard as a consequence. Results of this study can be helpful to set optimum bed temperature condition in FDM additive manufacturing.
基金supported by National Natural Science Foundation of China(No.61904094,No.61934009)China Postdoctoral Science Foundation(No.2020M670329)Beijing Innovation Center for Future Chips(ICFC).
文摘The successive approximation register(SAR)is one of the most energy-efficient analog-to-digital converter(ADC)architecture for medium-resolution applications.However,its high energy efficiency quickly diminishes when the target resolution increases.This is because a SAR ADC suffers from several major error source,including the sampling kT/C noise,the comparator noise,and the DAC mismatch.These errors are increasing hard to address in high-resolution SAR ADCs.This paper reviews recent advances on error suppression techniques for SAR ADCs,including the sampling kT/C noise reduction,the noise-shaping(NS)SAR,and the mismatch error shaping(MES).These techniques aim to boost the resolution of SAR ADCs while maintaining their superior energy efficiency.
文摘A novel approach for engineering application to human error probability quantification is presented based on an overview of the existing human reliability analysis methods.The set of performance shaping factors is classified as two subsets of dominant factors and adjusting factors respectively.Firstly,the dominant factors are used to determine the probabilities of three behavior modes.The basic probability and its interval of human error for each behavior mode are given.Secondly,the basic probability and its interval are modified by the adjusting factors,and the total probability of human error is calculated by a total probability formula.Finally,a simple example is introduced,and the consistency and validity of the presented approach are illustrated.
基金National Natural Science Foundation ofChina(No.60 4740 3 6)
文摘Shape from shading(SFS)is an important domain in computer vision.The paper presented an improved algorithm of shape from shading based on a single image according to an existed one.The presented algorithm enhanced the boundary constraints to eliminate the rotation distortion on the border of reconstructed object and introduced the factor of brightness error to weaken the influence irradiance equation’s nonlinearity on reconstructed errors.The reconstructed results verify the performance improvement in terms of accuracy by the input image of a synthetic image and a real image of weld.
基金Project supported by the National Natural Science Foundation of China(No.11071164)the Innovation Program of Shanghai Municipal Education Commission(No.13ZZ118)+1 种基金the Shanghai Leading Academic Discipline Project(No.XTKX2012)the Innovation Fund Project for Graduate Stu-dent of Shanghai(No.JWCXSL1201)
文摘This paper aims at analyzing the shapes of the bounded traveling wave solutions for a class of nonlinear wave equation with a quintic term and obtaining its damped oscillatory solutions. The theory and method of planar dynamical systems are used to make a qualitative analysis to the planar dynamical system which the bounded traveling wave solutions of this equation correspond to. The shapes, existent number, and conditions are presented for all bounded traveling wave solutions. The bounded traveling wave solutions are obtained by the undetermined coefcients method according to their shapes, including exact expressions of bell and kink profile solitary wave solutions and approximate expressions of damped oscillatory solutions. For the approximate damped oscillatory solution, using the homogenization principle, its error estimate is given by establishing the integral equation, which reflects the relation between the exact and approximate solutions. It can be seen that the error is infinitesimal decreasing in the exponential form.
