Effect of Training on Two-way Shape Memory Effect and Its Stability in a Ti-Ni-Hf High Temperature Shape Memory Alloy

The Effect of the thermal cycling training under constant strain on the two-way shape memory effect (TWSME) in a Ti36l\li49Hf15 high temperature shape memory alloy (SMA) has been investigated by bending tests. The results indicated that the training procedure is beneficial to get the better TWSME. The two-way shape memory strain increases with increasing the training strain. And it decreases with increasing the training temperature. The TWSME obtained in the present alloy shows poorer stability compared with that obtained in the TiNi alloys.

Two-way Shape Memory Effect in a Ti-Ni-Nb Shape Memory Alloy with Wide Hysteresis

A two-way shape memory effect (TWSM E) in the Ti46.3Ni44.7Nb9 alloy has been systematically investigated by means of bending test and transmission electron microscopy (TEM ) observations. Based on the analysis of the microstructure after training. the mechanism of TWSME in the Ti46.3 Ni44.7Nb9 alloy has been discussed.

INFLUENCE OF PROCESSING ON SHAPE MEMORY EFFECT OF Fe-Mn-Si-Ni-C-RE SHAPE MEMORY ALLOY

Effect of carbon, compound RE, quenching temperature, pre-strain and recovery temperature on shape memory effect (SME) of Fe-Mn-Si-Ni-C-RE shape memory alloy was studied by bent measurement, thermal cycle training, SEM etc. It was shown that the grains of alloys addition with compound RE became finer and SME increased evidently. SME of the alloy was weakening gradually as carbon content increased under small strain (3%). But in the condition of large strain (more than 6%), SME of the alloy whose carbon content range from 0.1% to 0.12% showed small decreasing range, especially of alloy with the addition of compound RE. Results were also indicated that SME was improved by increasing quenching temperature (>1000℃). The amount of thermal induced martensite increased and the relative shape recovery ratio could be increased to more than 40% after 3-4 times thermal training. The relative shape recovery ratio decreased evidently depending on rising of pre-strain. Furthermore, because speed of martensite transition was extremely great under higher tempering temperature (more than 450℃, ε → γ transition completed in 10s meanwhile the relative shape recovery ratio of the alloy increased rapidly.

Effect of chemical component on shape memory effect of Fe-Mn-Si-Ni-C-RE shape memory alloy

Effect of chemical component on shape memory effect (SME) of Fe-Mn-Si-Ni-C-RE shape memory alloys was studied by bent measurement, thermal cycle training, SEM etc. Results of study indicate that the alloys with high Mn content (25%) appeare better SME, especially in lower strain. SME improves evidently when Si is higher content, especially it’s range from 3% up to 4%. But brittleness of Fe-Mn-Si-Ni-C-RE alloy increases by increasing the Si content. SME of the alloy is weakening gradually as carbon content increases under small strain (3%). But in the condition of large strain (above 6%), SME of the alloy whose carbon content ranges from 0.1 % to 0.12% shows small decreasing range, especially of alloy with the addition of compound RE.

Effect of chemical component on shape memory effect of Fe-Mn-Si-Ni-C-RE shape memory alloy

Effect of chemical component on shape memory effect (SME) of Fe-Mn-Si-Ni-C-REshape memory alloys was studied by bent measurement, thermal cycle training, SEM etc. Results ofstudy indicate that the alloys with high Mn content (25%) appeare better SME, especially in lowerstrain. SME improves evidently when Si is higher content, especially it's range from 3% up to 4%.But brittleness of Fe-Mn-Si-Ni-C-RE alloy increases by increasing the Si content. SME of the alloyis weakening gradually as carbon content increases under small strain (3%). But in the condition oflarge strain (above 6%), SME of the alloy whose carbon content ranges from 0.1 % to 0.12% showssmall decreasing range, especially of alloy with the addition of compound RE.

A macroscopic multi-mechanism based constitutive model for the thermo-mechanical cyclic degeneration of shape memory effect of NiTi shape memory alloy

A macroscopic based multi-mechanism constitutive model is constructed in the framework of irreversible thermodynamics to describe the degeneration of shape memory effect occurring in the thermo-mechanical cyclic deformation of NiTi shape memory alloys (SMAs). Three phases, austenite A, twinned martensite and detwinned martensite , as well as the phase transitions occurring between each pair of phases (, , , , and are considered in the proposed model. Meanwhile, two kinds of inelastic deformation mechanisms, martensite transformation-induced plasticity and reorientation-induced plasticity, are used to explain the degeneration of shape memory effects of NiTi SMAs. The evolution equations of internal variables are proposed by attributing the degeneration of shape memory effect to the interaction between the three phases (A, , and and plastic deformation. Finally, the capability of the proposed model is verified by comparing the predictions with the experimental results of NiTi SMAs. It is shown that the degeneration of shape memory effect and its dependence on the loading level can be reasonably described by the proposed model.

Microstructure,compression property and shape memory effect of Ru-Nb high temperature shape memory alloy

The microstructure,phase transformation,compression property and strain recovery characteristics of equiatomic Ru-Nb high temperature shape memory alloy were investigated by means of optical microscope,X-ray diffraction(XRD),differential scanning calorimetry(DSC),compression tests and transmission electron microscopy(TEM).When cooling the alloy specimen from high temperature to room temperature,β(parent phase)→β’(interphase)→β″(martensite) two step phase transformation occurs.The microstructure at room temperature shows regularly arranged band morphology with the monoclinic crystal structure.The twinning relationship between the martensite bands was determined to be(101) Type I.Reorientation and of the martensite bands inside the variant and dislocation were found during compression at room temperature.The maximum complete recovery strain is about 1.5%.

Phase transformation behaviors and shape memory effects of TiNiFeAl shape memory alloys

Measurements of electrical resistivity, X-ray diffraction, and tensile test at room temperature and ？196°C were performed to investigate the effects of Al addition substituting Ni on the phase transformation behaviors, the mechanical properties, and the shape memory effects of Ti50Ni47Fe2Al1 and Ti50Ni46.5Fe2.5Al1 alloys. It is found that 1at% Al addition dramatically decreases the martensitic start transformation temperature and expands the transformation temperature range of R-phase for TiNiFeAl alloys. The results of tensile test indicate that 1at% Al improves the yield strength of Ti50Ni47Fe2Al1 and Ti50Ni46.5Fe2.5Al1 alloys by 40% and 64%, but de- creases the plasticity to 11% and 12% from 26% and 27% respectively. Moreover, excellent shape memory effect of 6.6% and 7.5% were found in Ti50Ni47Fe2Al1 and Ti50Ni46.5Fe2.5Al1 alloys, which results from the stress-induced martensite transformation from the R-phase.

Slow Relaxation and Memory Effect in Ti_(50)Ni_(47)Fe_3 Shape Memory Alloy

The slow relaxation of resistance and memory effect in TisoNi_(47)Fe_3 shape memory alloy(SMA) are found for the first time.An evidence for CDW mechanism of incommensurate and commensurate phases in SMA was provided.

Microstructure,Compression Property and Shape Memory Effect of Equiatomic TaRu High Temperature Shape Memory Alloy

The microstructure, phase transformation, compression property and strain recovery characteristics of equiatomic TaRu super high temperature shape memory alloy have been studied by optical microscope, XRD, DTA, compression tests and TEM observations. When cooling the alloy specimen from high temperature to the room temperature, β(parent phase)→β'(interphase) β→' (martensite) two-step phase transformations occur. The microstructure at room temperature show regularly arranged band morphology, with the monoclinic crystal structure. The twinning relationship between the martensite bands is determined to be (101) of Type I. Reorientation and coalescence of the martensite bands inside the variant happened during compression at room temperature. The β'→β reversible transformation contributes mainly the shape memory effect, with the maximum completely recovery strain of 2%.

Microstructure and Shape Memory Effect of Cu-Zn-Ni Shape Memory Alloys

The microstructure, martensitic transformation behavior and shape memory effect of Cu-Zn-Ni shape memory alloy have been studied by X-ray diffraction (XRD), optical microscopy (OM) and differential scanning calorimetry (DSC). The results show that the recrystallization occurs in the hot-rolled Cu-Zn-Ni alloy by annealing at 800℃ and alloy is primarily composed of martensite. A reverse martensite transformation temperature higher than 100℃ upon heating has been detected. The alloys exhibit good ductility and shape memory effect (SME). The results obtained are discussed in detail.

Twice reverse shape memory effect in CuZnAl shape memory alloy

The variations of the shape memory effects in the Cu-13Zn-15Al(mole fraction,%) alloy upon successive heating (the rate of heating is 5 ℃/min) have been st udied by means of ρ—T curve,shape memory effect measurement,optical met allographical observation and X-ray diffraction. The first abnormal reverse sha pe memory effect occurs when the tested alloy is heated to the temperature below 320 ℃;when it is heated to the temperature between 320 ℃ and 450 ℃,the forward shape memory effect occurs;in the two stages,the shape of the sample r emains the same as that in the furnace when it is taken out from the furnace and air-cooled;when the tested alloy is heated to the temperature above 450 ℃,the shape of the sample remains unchanged during heating,but the second reverse shape memory effect occurs after it is air-quenched.

Two-way shape memory effect and its stability in Ti-Ni-Hf high temperature shape memory alloy

The two-way shape memory effect（TWSME） in a Ti36Ni49Hf15 high temperature shape memory alloy（SMA） was systematically studied by bending tests. In the TiNiHf alloy, the martensite deformation is an effective method to get two-way shape memory effect even with a small deformation strain. The results indicate that the internal stress field formed by the bending deformation is in the direction of the preferentially oriented martensite variants formed during the bending deformation. Upon cooling the preferentially oriented martensite variants form under such an oriented stress field, which should be responsible for the generation of the two-way shape memory effect. Proper training process benefits the formation of the oriented stress field, resulting in the improvement of the two-way shape memory effect. A maximum TWSME of 0.88% is obtained in the present alloy.

DSC study on temperature memory effect of NiTi shape memory alloy

A systematic study on the temperature memory effect (TME) in a polycrystalline NiTi shape memory alloy was presented. The investigation was carried out through a series of differential scanning calorimeter (DSC) tests. Two types of tests were conducted, namely single-step test and multi-step test. The influence of the step temperature on the peak/trough temperatures in the subsequent heating process and the associated energy absorption/release in the phase transformations was investigated. Using a simple theoretical model, the exact mechanism behind TME was studied.

Effect of solution treatment on the microstructure,phase transformation behavior and functional properties of NiTiNb ternary shape memory alloys fabricated via laser powder bed fusion in-situ alloying

Post-heat treatment is commonly employed to improve the microstructural homogeneity and enhance the mechanical performances of the additively manufactured metallic materials.In this work,a ternary(NiTi)91Nb9(at.%)shape memory alloy was produced by laser powder bed fusion(L-PBF)using pre-alloyed NiTi and elemental Nb powders.The effect of solution treatment on the microstructure,phase transformation behavior and mechanical/functional performances was investigated.The in-situ alloyed(NiTi)91Nb9 alloy exhibits a submicron cellular-dendritic structure surrounding the supersaturated B2-NiTi matrix.Upon high-temperature(1273 K)solution treatment,Nb-rich precipitates were precipitated from the supersaturated matrix.The fragmentation and spheroidization of the NiTi/Nb eutectics occurred during solution treatment,leading to a morphological transition from mesh-like into rod-like and sphere-like.Coarsening of theβ-Nb phases occurred with increasing holding time.The martensite transformation temperature increases after solution treatment,mainly attributed to:(i)reduced lattice distortion due to the Nb expulsion from the supersaturated B2-NiTi,and(ii)the Ti expulsion from theβ-Nb phases that lowers the ratio Ni/Ti in the B2-NiTi matrix,which resulted from the microstructure changes from non-equilibrium to equilibrium state.The thermal hysteresis of the solutionized alloys is around 145 K after 20%pre-deformation,which is comparable to the conventional NiTiNb alloys.A short-term solution treatment(i.e.at 1273 K for 30 min)enhances the ductility and strength of the as-printed specimen,with the increase of fracture stress from(613±19)MPa to(781±20)MPa and the increase of fracture strain from(7.6±0.1)%to(9.5±0.4)%.Both the as-printed and solutionized samples exhibit good tensile shape memory effects with recovery rates>90%.This work suggests that post-process heat treatment is essential to optimize the microstructure and improve the mechanical performances of the L-PBF in-situ alloyed parts.

Effect of solution treatment and aging on microstructural evolution and mechanical behavior of NiTi shape memory alloy

As-received nickel-titanium （NiTi） shape memory alloy with a nominal composition of Ni50.9Ti49.1 （mole fraction,%） was subjected to solution treatment at 1123 K for 2 h and subsequent aging for 2 h at 573 K, 723 K and 873 K, respectively. The influence of solution treatment and aging on microstructural evolution and mechanical behavior of NiTi alloy was systematically investigated by transmission electron microscopy （TEM）, high resolution transmission electron microscopy （HRTEM）, scanning electron microscopy （SEM） and compression test. Solution treatment contributes to eliminating the Ti2Ni phase in the as-received NiTi sample, in which the TiC phase is unable to be removed. Solution treatment leads to ordered domain of atomic arrangement in NiTi alloy. In all the aged NiTi samples, the Ni4Ti3 precipitates, the R phase and the B2 austenite coexist in the NiTi matrix at room temperature, while the martensitic twins can be observed in the NiTi samples aged at 873 K. In the NiTi samples aged at 573 and 723 K, the fine and dense Ni4Ti3 precipitates distribute uniformly in the NiTi matrix, and thus they are coherent with the B2 matrix. However, in the NiTi sample aged at 873 K, the Ni4Ti3 precipitates exhibit the very inhomogeneous size, and they are coherent, semi-coherent and incoherent with the B2 matrix. In the case of aging at 723 K, the NiTi sample exhibits the maximum yield strength, where the fine and homogeneous Ni4Ti3 precipitates act as the effective obstacles against the dislocation motion, which results in the maximum critical resolved shear stress for dislocation slip.

Effects of second phases on mechanical properties and martensitic transformations of ECAPed TiNi and Ti-Mo based shape memory alloys

TiNi and Ti-based shape memory alloys were processed by equal channel angular pressing （ECAP） at 673-773 K along Bc route to obtain ultrafine grains for increasing the strength of parent phase and improving the functional properties. The effects of both thermodynamically stable and metastable second phases on the mechanical properties and martensitic transformations of these alloys were investigated. It is found that thermodynamically stable Ti2Ni phase has no effect on martensitic transformation and superelasticity of Ti-rich TiNi alloy, thermodynamically stable α phase is harmful for ductility of Ti-Mo-Nb-V-Al alloy, but metastable Ti3Ni4 phase is effective for R phase transformation, martensitic transformation and superelasticity of Ni-rich TiNi alloy. The mechanisms of the second phases on the martensitic transformations and mechanical properties were discussed.

Machine learning-assisted efficient design of Cu-based shape memory alloy with specific phase transition temperature

The martensitic transformation temperature is the basis for the application of shape memory alloys(SMAs),and the ability to quickly and accurately predict the transformation temperature of SMAs has very important practical significance.In this work,machine learning(ML)methods were utilized to accelerate the search for shape memory alloys with targeted properties(phase transition temperature).A group of component data was selected to design shape memory alloys using reverse design method from numerous unexplored data.Component modeling and feature modeling were used to predict the phase transition temperature of the shape memory alloys.The experimental results of the shape memory alloys were obtained to verify the effectiveness of the support vector regression(SVR)model.The results show that the machine learning model can obtain target materials more efficiently and pertinently,and realize the accurate and rapid design of shape memory alloys with specific target phase transition temperature.On this basis,the relationship between phase transition temperature and material descriptors is analyzed,and it is proved that the key factors affecting the phase transition temperature of shape memory alloys are based on the strength of the bond energy between atoms.This work provides new ideas for the controllable design and performance optimization of Cu-based shape memory alloys.

Influence of recovery heating rate on shape memory effect in up-quenched Cu-Al-Mn alloy

The effect of recovery heating rate on shape memory effect of the up-quenched Cu-8.88Al-10.27Mn（mass fraction, %） alloy was investigated by optical microscopy, electron transmission microscopy（TEM） and electrical resistivity measurement. It is found that the shape recovery rate decreases as the heating rate decreases. It can reach 75% when the heating rate is 20 ℃/min, while it is only 8% when the heating rate is 1 ℃/min. In situ microstructure observation indicates that the dependence of shape memory effect on recovery heating rate is caused by the stabilization of twinned martensite induced by deformation. The analysis of electrical resistivity shows that the stabilization of twinned martensite may be ascribed to formation of compound defects of vacancies and dislocations at the boundaries of twinned martensite during the slow heating. The compound defects prevent the reverse transformation of twinned martensite.

Effect of Sn substitution and heat treatment on microstructure and microhardness of Co_(38)Ni_(34)Al_(28-x)Sn_x magnetic shape memory alloys

Sn was used to replace Al in Co38Ni34Al28 alloy. The microstructure and microhardness of Co38Ni34Al28-xSnx （x=0, 1, 2, 3） magnetic shape memory alloys were investigated at different heat treatment temperatures （1373 K, 1473 K, and 1573 K） for 2 h. The results show that more Sn substitution reduces the content of γ-phase and a partial phase of martensite can be obtained in Co38Ni34Al28-xSnx （x=1, 2, 3） alloys after treatment at 1573 K for 2 h. The maximum martensite phase appears when 2% Al is substituted by Sn. The reverse martensitic transformation temperature of Co38Ni34Al28-xSnx alloys increases at x=1 and 2, then decreases as x=3. As the content of Sn and the temperature increase, the microhardness will increase.