The causes of local scour are generally categorized into flow condition, structure, and riverbed material. A three-dimensional vortex flow generated with the influence of the structure is the main factors of the flow ...The causes of local scour are generally categorized into flow condition, structure, and riverbed material. A three-dimensional vortex flow generated with the influence of the structure is the main factors of the flow conditions, and the size of the particles is assumed to be the main factor of the riverbed case. Various studies about pier local scour have been carried out by researchers since the 1960s, and a large number of experimental formulas have been suggested. Difficulties were encountered by these past studies, however, in terms of considering the influence of various riverbed materials and scour changes (floods, etc.) on time, with the condition of maximum scour depth. In the case of Korea, especially, scour influenced by various riverbed materials and the frequency of floods have been determined to be very important factors. Therefore, the ultimate purpose of this study on pier scour is to suggest the scour examination method that could consider various riverbed materials and the frequency of floods. In this study, the periodic changes in local scour based on the differences in the diameters of four types of bed materials, and on the hydraulic condition of the initial scour, were determined and compared with those in former studies. Using the results of the comparison, this study aims to determine the changes in the shear-stress around piers for various bed materials through the effect of time on scour depth (S, Smax), the shear-stress around piers, and the particles’ critical shear stress (τc).展开更多
Two improvements have been made on the calculation of plastic strain ratio (r value) in BCC monocrystals by considering the differences in the critical shear stresses among the three slip systems and the rotation of c...Two improvements have been made on the calculation of plastic strain ratio (r value) in BCC monocrystals by considering the differences in the critical shear stresses among the three slip systems and the rotation of crystal lattice. It is found that the results calculated by the improved method are more rational.展开更多
Although the cyclic rotation of the principal stress direction is important,its effect on the deformation behavior and dynamic properties of the reinforced soil has not been reported to date.Tests carried out on large...Although the cyclic rotation of the principal stress direction is important,its effect on the deformation behavior and dynamic properties of the reinforced soil has not been reported to date.Tests carried out on large-scale hollow cylinder samples reveal that the cyclic rotation of the principal stress direction results in significant variations of strain components(ε,ε,εand γ) with periodic characteristics despite the deviatoric stress being constant during tests.This oscillation can be related to the corresponding variations in the stress components and the anisotropic fabric that rotate continuously along the principal stress direction.Sand under rotation appears to develop a plastic strain.Similar trends are observed for reinforced sand,but the shear interaction,the interlocking between particles and reinforcement layer,and the confinement result in significant reductions in the induced strains and associated irrecoverable plastic strains.Most of the strains occur in the first cycle,and as the number of cycles increases,the presence of strains becomes very small,which is almost insignificant.This indicates that the soil has reached anisotropic critical state(ACS),where a stable structure is formed after continuous orientation,realignment and rearrangement of the particles accompanied with increasing cyclic rotation.Rotation in the range of 60°-135° produces more induced strains even in the presence of the reinforcement,when compared with other ranges.This relates to the extension mode of the test in this range in which σ>σand to the relative approach between the mobilized plane and the weakest horizontal plane.Reinforcement results in an increase in shear modulus while it appears to have no effect on the damping ratio.Continuous cycles of rotation result in an increase in shear modulus and lower damping ratio due to the densification that causes a decrease in shear strain and less dissipation of energy.展开更多
文摘The causes of local scour are generally categorized into flow condition, structure, and riverbed material. A three-dimensional vortex flow generated with the influence of the structure is the main factors of the flow conditions, and the size of the particles is assumed to be the main factor of the riverbed case. Various studies about pier local scour have been carried out by researchers since the 1960s, and a large number of experimental formulas have been suggested. Difficulties were encountered by these past studies, however, in terms of considering the influence of various riverbed materials and scour changes (floods, etc.) on time, with the condition of maximum scour depth. In the case of Korea, especially, scour influenced by various riverbed materials and the frequency of floods have been determined to be very important factors. Therefore, the ultimate purpose of this study on pier scour is to suggest the scour examination method that could consider various riverbed materials and the frequency of floods. In this study, the periodic changes in local scour based on the differences in the diameters of four types of bed materials, and on the hydraulic condition of the initial scour, were determined and compared with those in former studies. Using the results of the comparison, this study aims to determine the changes in the shear-stress around piers for various bed materials through the effect of time on scour depth (S, Smax), the shear-stress around piers, and the particles’ critical shear stress (τc).
文摘Two improvements have been made on the calculation of plastic strain ratio (r value) in BCC monocrystals by considering the differences in the critical shear stresses among the three slip systems and the rotation of crystal lattice. It is found that the results calculated by the improved method are more rational.
文摘Although the cyclic rotation of the principal stress direction is important,its effect on the deformation behavior and dynamic properties of the reinforced soil has not been reported to date.Tests carried out on large-scale hollow cylinder samples reveal that the cyclic rotation of the principal stress direction results in significant variations of strain components(ε,ε,εand γ) with periodic characteristics despite the deviatoric stress being constant during tests.This oscillation can be related to the corresponding variations in the stress components and the anisotropic fabric that rotate continuously along the principal stress direction.Sand under rotation appears to develop a plastic strain.Similar trends are observed for reinforced sand,but the shear interaction,the interlocking between particles and reinforcement layer,and the confinement result in significant reductions in the induced strains and associated irrecoverable plastic strains.Most of the strains occur in the first cycle,and as the number of cycles increases,the presence of strains becomes very small,which is almost insignificant.This indicates that the soil has reached anisotropic critical state(ACS),where a stable structure is formed after continuous orientation,realignment and rearrangement of the particles accompanied with increasing cyclic rotation.Rotation in the range of 60°-135° produces more induced strains even in the presence of the reinforcement,when compared with other ranges.This relates to the extension mode of the test in this range in which σ>σand to the relative approach between the mobilized plane and the weakest horizontal plane.Reinforcement results in an increase in shear modulus while it appears to have no effect on the damping ratio.Continuous cycles of rotation result in an increase in shear modulus and lower damping ratio due to the densification that causes a decrease in shear strain and less dissipation of energy.
