Electro-elastic Fields of Piezoelectric Materials with An Elliptic Hole under Uniform Internal Shearing Forces

The existing investigations on piezoelectric materials containing an elliptic hole mainly focus on remote uniform tensile loads. In order to have a better understanding of the fracture behavior of piezoelectric materials under different loading conditions, theoretical and numerical solutions are presented for an elliptic hole in transversely isotropic piezoelectric materials subjected to uniform internal shearing forces based on the complex potential approach. By solving ten variable linear equations, the analytical solutions inside and outside the hole satisfying the permeable electric boundary conditions are obtained. Taking PZT-4 ceramic into consideration, numerical results of electro-elastic fields along the edge of the hole and axes, and the electric displacements in the hole are presented. Comparison with stresses in transverse isotropic elastic materials shows that the hoop stress at the ends of major axis in two kinds of material equals zero for the various ratios of major to minor axis lengths; If the ratio is greater than 1, the hoop stress in piezoelectric materials is smaller than that in elastic materials, and if the ratio is smaller than 1, the hoop stress in piezoelectric materials is greater than that in elastic materials; When it is a circle hole, the shearing stress in two materials along axes is the same. The distribution of electric displacement components shows that the vertical electric displacement in the hole and along axes in the material is always zero though under the permeable electric boundary condition; The horizontal and vertical electric displacement components along the edge of the hole are symmetrical and antisymmetrical about horizontal axis, respectively. The stress and electric displacement distribution tends to zero at distances far from the elliptical hole, which conforms to the conclusion usually made on the basis of Saint-Venant’s principle. Unlike the existing work, uniform shearing forces acting on the edge of the hole, and the distribution of electro-elastic fields inside and outside the elliptic hole are considered.

Analysis of Photoelectric Hybridization Measurement on Shearing Force for Flat Shearer

This paper introduces a kind of photoelectric hybridization measuring process.Owing to the characteristics of the compact form of shearing equipment to be analyzed and the connecting rod existing in two directional stress state during operation etc.,it is hard to obtain results by means of single electrical testing process.For this reason,this paper derives a group of calculation formulas of hybridization measuring process through comprehensive discussion of photoelectric analysis and electrical testing theories,thus providing an analytical method for actual measurement of complex engineering problems.

Establishment of Optimal Blade Clearance of Stainless Steel Rolling-Cut Shear and Test of Shearing Force Parameters

The purpose aims to improve the plate shearing section quality and metal yield by means of optimal blade clearance adjustment model of rolling-cut shear and accurate calculation of the maximum shearing force , as well as for the system optimization design , structure optimization design to provide important basis.A 3 500mm rolling shear of a large stainless steel factory was taken as the test object , and the blade clearance under different influence factors of the clearance value and the shearing section were tested.The optimized production accumulated data regression analysis and the rolling shear process of stainless steel shear test.The test results show that the optimal blade clearance adjustment module is a comprehensive function , which include steel plate thickness , material , temperature and shear plate volume.The shear stress at starting stage with the relative penetration depth increases affected by the above factors , and the fracture peak decreases rapidly after being cut into the roll phase constant.

Numerical Simulation Analysis of Influence Factors to Shearing Force of Rolling Shear

The calculation results show that relative cut-in depth at the moment of maximum shearing force decreases with the increase of steel plate thickness; along with blade clearance increasing, shearing force would increase slightly compared with the slide pressure of blade carrier; shearing force increases significantly with the increasing blunt end radius; shearing force displays a bit decrement with the decreasing platen force, while the pressure on slide plate of blade carrier increases substantially; shearing force increases a bit with the increasing shear velocity and decreases when nip angle increases while the horizontal component force of shearing force along the direction of plate width increases rapidly. The above results have important reference and actual using value for studying calculation of mechanical parameters of rolling shear and its structural design.

BOP shear force evaluation under complex scenarios

As the“throat”of the drilling well control system,ram blowout preventers(BOPs)can effectively prevent blowout accidents.However,the ram shear mechanism under complex working conditions is unclear,and it is difficult to evaluate the ram BOP shear force,leading to frequent shear failure accidents in oilfields.Aiming at the above problems,this paper takes the double-V ram BOP as the research object,and integrates the methods of theoretical analysis,simulation modeling,and test verification to analyze the shear force in the pipe shear process under both static and moving conditions.A ram BOP shear force evaluation method is proposed based on equivalent stress.Finally,by comparing with calculation data and experimental data,the error between them is less than 5%,demonstrating the applicability and effectiveness of the proposed method.The research results can provide a theoretical basis for oilfield operations of ram BOPs.

Near Crack Line Elastic-Plastic Analysis for an Infinite Plate Loaded by a Pair of Point Shear Forces

The near crack line analysis method was used to investigate a crack loaded by a pair of point shear forces in an infinite plate in an elastic-perfectly plastic solid. The analytical solution was obtained, that is the elastic-plastic fields near crack line and law that the length of the plastic zone along the crack line is varied with external loads. The results are sufficiently precise near the crack line and are not confined by small scale yielding conditions.

Effect of ultrasonic power and bonding force on the bonding strength of copper ball bonds

Copper wire, serving as a cost-saving alternative to gold wire, has been used in many high-end thermosonic ball bonding applications. In this paper, the bond shear force, bond shear strength, and the ball bond diameter are adopted to evaluate the bonding quality. It is concluded that the ef/~cient ultrasonic power is needed to soften the ball to form the copper bonds with high bonding strength. However, excessive ultrasonic power would serve as a fatigue loading to weaken the bonding. Excessive or less bonding force would cause cratering in the silicon.

Effect of the particle temperature on lift force of nanoparticle in a shear rarefied flow

The nanoparticles suspended in a shear flow are subjected to a shear lift force,which is of great importance for the nanoparticle transport.In previous theoretical analysis on the shear lift,it is usually assumed that the particle temperature is equal to the temperature of the surrounding gas media.However,in some particular applications,the particle temperature can significantly differ from the gas temperature.In the present study,the effect of particle temperature on the shear lift of nanoparticles is investigated and the corresponding formulas of shear lift force are derived based on the gas kinetic theory.For extremely small nanoparticles(with radius R<2 nm)or large nanoparticles(R>20 nm),the influence of the particle temperature can be neglected.For the intermediate particle size,the relative error induced by the equal gas–particle temperature can be significant.Our findings can bring an insight into accurate evaluation of the nanoparticle transport properties.

A Modified Monte Carlo Model of Speckle Tracking of Shear Wave Induced by Acoustic Radiation Force for Acousto-Optic Elasticity Imaging

A modified Monte Carlo model of speckle tracking of shear wave propagation in scattering media is proposed. The established Monte Carlo model mainly concerns the variations of optical electric field and speckle. The two- dimensional intensity distribution and the time evolution of speckles in different probe locations are obtained. The fluctuation of speckle intensity tracks the acoustic-radiation-force shear wave propagation, and especially the reduction of speckle intensity implies attenuation of shear wave. Then, the shear wave velocity is estimated quantitatively on the basis of the time-to-peak algorithm and linear regression processing. The results reveal that a smaller sampling interval yields higher estimation precision and the shear wave velocity is estimated more efficiently by using speckle intensity difference than by using speckle contrast difference according to the estimation error. Hence, the shear wave velocity is estimated to be 2.25 m/s with relatively high accuracy for the estimation error reaches the minimum （0.071）.

Derivation of energy-based base shear force coefficient considering hysteretic behavior and P-delta effects

A modified energy-balance equation accounting for P-delta effects and hysteretic behavior of reinforced concrete members is derived. Reduced hysteretic properties of structural components due to combined stiffness and strength degradation and pinching effects, and hysteretic damping are taken into account in a simple manner by utilizing plastic energy and seismic input energy modification factors. Having a pre-selected yield mechanism, energy balance of structure in inelastic range is considered. P-delta effects are included in derived equation by adding the external work of gravity loads to the work of equivalent inertia forces and equating the total external work to the modified plastic energy. Earthquake energy input to multi degree of freedom（MDOF） system is approximated by using the modal energy-decomposition. Energybased base shear coefficients are verified by means of both pushover analysis and nonlinear time history（NLTH） analysis of several RC frames having different number of stories. NLTH analyses of frames are performed by using the time histories of ten scaled ground motions compatible with elastic design acceleration spectrum and fulfilling duration/amplitude related requirements of Turkish Seismic Design Code. The observed correlation between energy-based base shear force coefficients and the average base shear force coefficients of NLTH analyses provides a reasonable confidence in estimation of nonlinear base shear force capacity of frames by using the derived equation.

A force control high-order single-step-β method (HSM) for substructure pseudo-dynamic testing

This paper proposes a new technique which introduces the high-order single-step-β method(HSM)into the experimental study on the substructure pseudo-dynamic testing(SPDT).The technique is based on the proposed concept of equivalent shear stiffness which can meet the requirement of the HSM algorithm.A study is done to theoretically validate the technique by the numerical analysis of two-storey shear building structure,in comparison of the proposed substructure pseudo-dynamic testing algorithm with the central difference method(CDM).Then,a full-scale SPDT model,the three-storey frame-supported reinforced concrete short-limb masonry shear wall structure,is designed and tested to simulate the seismic response of the corresponding six-storey structure and verify the proposed force control HSM technique.Meanwhile,the techniques of both stiffness correction and force control are suggested to control algorithmic error,control error and measurement error.The results indicate that the force control HSM can be used in the full-scale multi-degree-of-freedom(MDOF)substructure pseudo-dynamic testing before descent segment of structure restoring force properties.

Role of Interatomic Force to Critical Resolved Shear Stress of Single Crystals

Experimental results of the temperature dependence of critical resolved. shear stresses (CRSS)of Mo, Fe, Al and Mg single crystals are shown. Associating reports in recent years, we point out that the approximate exponential relationship between CRSS and the absolute temperatureat least in the region of the steep temperature dependence range of many materials is more common, even for bcc, fcc, and hcp single crystals. polycrystals and other covalent crystals,provided that the slip plane and slip direction are kept the same. Successful explanation with atomic force law shows that the interatomic forces (electronic structure) play a decisive role in determining the temperature dependence of yield stresses for a large number of materials.

Study on the resistance spot welding technology of 22MnMoB hot stamping quenched steel

In this paper, the spot welding technology of a new kind of 22MnMoB hot stamping quenched steel sheet was systematically studied by power frequency spot welder. Through a series of technology and test experiments, we have obtained the optimal spot welding technological parameter condition. According to the results, the relations among spot welding technological parameter, welding nugget, mechanical property and fracture mode were discussed. The effects of all the welding parameters such as welding current, welding time and electrode force on the quality of joint can be boiled down to one thing--the diameter of welding nugget. The experimental results showed that welding nugget diameter determines the mechanical property of spot welding joint and the relation between welding nugget diameter and the mechanical property of joint presents a kind of linear mathematic representation. There are two typical fracture models of 22MnMoB hot stamping quenched steel sheet, i.e., interracial fracture and nugget pullout. Other than mild steel or normal high strength steel, in the shearing tensile test, hot stamping quenched steel has a great tendency to fail in interfacial mode due to the effects of high strength matrix structure, welding soft zone and the porosity level of fusion zone.

SEISMIC DAMAGE PREDICTION ON MULTI-STORYBRIOK BUILDINGS WITH TWO FRAME-SHEAR-WALL-SUPPORTED STORIES

This paper presents a method for searching the weak story by using the ultimate shear force coefficient on the multi-story brick buildings with two frame-shear-wall-supported stories. The method of seismic damage prediction is discussed according to different weak stories. When the first story is t theweak one,the damage state of the building can be determined by the displacement ratio. The prediction method is also used in a practical engineering project.

Effect of Delay Chilling on μ-calpain Activities and the Tenderness of Bovine M. longissimus

μ-calpain activities and shear force values of bovine M. longissimus from Chinese Yellow crossbred bulls were analyzed,and the effect of delay chilling on μ-calpain activities and the tenderness of beef during postmortem aging were studied. The results showed that delay chilling significantly improved μ-calpain activities (P<0.05) and enhanced the tenderness of bovine M. longissimus during earlier aging periods compared with conventional chilling. But in later aging periods,delay chilling weakened the effect on the tenderness of beef because of premature consumption of μ-calpain. The experiment results confirmed that delay chilling improved the rate of postmortem aging of beef and remarkably enhanced the tenderness of beef through the effect of delay chilling on μ-calpain activities.

Recent Advances in Directed Assembly of Nanowires or Nanotubes

Nanowires and nanotubes of diverse material compositions,properties and/or functions have been produced or fabricated through various bottom-up or top-down approaches.These nanowires or nanotubes have also been utilized as potential building blocks for functional nanodevices.The key for the integration of those nanowire or nanotube based devices is to assemble these one dimensional nanomaterials to specific locations using techniques that are highly controllable and scalable.Ideally such techniques should enable assembly of highly uniform nanowire/nanotube arrays with precise control of density,location,dimension or even material types of nanowires/nanotubes.Numerous assembly techniques are being developed that can quickly align and assemble large quantities of one type or multiple types of nanowires through parallel processes,including flow-assisted alignment,Langmuir-Blodgett assembly,bubble-blown technique,electric/magnetic-field directed assembly,contact/roll printing,knocking-down,etc..With these assembling techniques,applications of nanowire/nanotube based devices such as flexible electronics and sensors have been demonstrated.This paper delivers an overall review of directed nanowire/nanotube assembling approaches and analyzes advantages and limitations of each method.The future research directions have also been discussed.

An alternative practical design method for structures with viscoelastic dampers

Viscoelastic dampers（VEDs） are one of the most common passive control devices used in new and retrofit building projects which reduce the structure responses and dissipate seismic energy during an earthquake.Various methods to design this kind of dampers have been proposed based on the desired level of additional damping,eigenvalue assignment,modal strain energy,linear quadratic regulator control theories,and other approaches.In the current engineering practice,the popular method is the one based on the modal strain energy that uses the inter-story lateral stiffness as one of the main variables for damper design.However,depending on the configuration of the structure,in some cases the resulting interstory lateral stiffness can be very large.Consequently,the dampers size would also be large producing much more damping than that effectively necessary,resulting in an increase of the overall cost of the supplemental damping system and causing excessive stress on the structural elements connected to the dampers.In this paper an alternative practical design method for structures with VEDs is proposed.This method uses the inter-story shear forces as one of the main variables to accomplish the damper design compared to what was done in previous studies.Nonlinear time-history analyses were conducted on a 7-story reinforced concrete（RC） structure to check the reliability and effectiveness of the proposed method.Comparisons on the seismic performance between the structure without dampers and that equipped with VEDs were carried out.It is concluded that the proposed method results in a very suitable size of dampers,which are able to improve the performance of the structure at all levels of earthquake ground motions and satisfying the drift requirement prescribed in the codes.

A numerical study of macro-mesoscopic mechanical properties of gangue backfill under biaxial compression

Based on the Particle Flow Code(PFC^(2D)) program,we set up gangue backfill models with different gangue contents and bond strength,and studied the stress-strain behaviours,the pattern of shear band and force chains,motion and fragmentation of particles under biaxial compression.The results show that when the bond strength or contents of gangue are high,the peak strength is high and the phenomena of post-peak softening and fluctuation are obvious.When gangue contents are low,the shape of the shear band is symmetrical and most strong force chains transfer in soil particles.With an increase in gangue content,the shape of the shear band becomes irregular and the majority of strong force chains turn to transfer in gangue particles gradually,most of which distribute along the axial direction.When the gangue content is higher than 50%,the interconnectivity of strong force chains decreases gradually:at the same time,the strong force chains become tilted and the stability of the system tends to decrease.With an increase in external loading,the coordination numbers of the system increase at first and then decrease and the main pattern of force chains changes into columnar from annular.However,after the forming of the advantageous shear band,the force chains external to the shear band maintain their columnar shape while the inner ones bend obviously.As a result,annular force chains form.

Effect of welding current on strength and microstructure in resistance spot welding of AZ31 Mg alloy

In this paper, resistance spot welding were performed on lmm-thickness magnesium AZ31B plates. The effect of welding current on the microstructure and tensile shear force was investigated. It was found that the welding current governed the nugget growth, and the nugget could not form if current levels were insufficient. The nugget revealed a homogeneous, equiaxed, fine-grained structure, which consisted of non-equilibrium microstructure of α-phase dendrites surrounded by eutectic mixtures of α and β（ Mg17All2 ） in the grain boundaries. With increasing welding current, the size of grains in nugget would be more smaller and uniform, and the width of plastic rings would be larger. Tensile shear tests showed that tensile shear force of the joints increased with increasing welding current when the welding current was smaller than 17 000 A. The maximum tensile shear force was up to 1980 N.

Effect of surfactant on zeta potential and rheology behavior of methylene bis (thiocyanate) suspension concentrate

Methylene bis(thiocyanate)(MBT) is insoluble in water, so suspension concentrate(SC) of MBT is extremely relied on surfactants. In this paper, SC of MBT was prepared with wet-grinding technology, and the effect of surfactants,such as Morwet D425(D425) and Morwet EFW(EFW)(two kinds of dispersant), on the Zeta potential and rheology behavior of MBT SC were investigated. The results showed that the Zeta potential absolute value of MBT SC increased with the increasing content of D425, and it decreased with the increasing content of EFW at acidic solution(pH = 4.5). In the combination system of D425 and EFW, Zeta potential of MBT SC decreased first and then increased with the increasing content of EFW. The relationship between shear rate(γ) and viscosity(η) was studied according to Herschel–Bulkley model: η = η0+ k/γ, and the relationship between shear rate(γ) and shear force(τ) was investigated according to:τ = τ0+Kγ~n. It was revealed that the mixed fluid belonged to Yield Pseudoplastic Fluid.